FCC ID: EW780-1960-00A Video Baby Monitor

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5480368.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Go to www.vtechcanada.com for the latest VTech product news. VM3254 VM3254-2 Video Baby Monitor Quick start guide

(Canada version) For more support information S m 06/21. VM3254-X_CA_QSG_V1. 2021 VTech Technologies Canada Ltd. All rights reserved. Specifications are subject to change without notice. C22.2 NO.62368-1 CSA STD. CERTIFIED TO 62368-1 UL STD. CONFORMS TO The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license. The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license. The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license. Credits:

Parent unit power adapter: Output: 5V DC @ 1A Baby unit power adapter: Output: 6V DC @ 400mA Parent unit: 3.6V, 2600mAh Li-ion, 9.36Wh Li-ion battery Power requirements may vary according to environmental conditions at the time of use. Nominal effective rangeMaximum power allowed by FCC and IC. Actual operating range

(QVGA 320x240 pixel) 2.8 Color LCD 32 LCD Channels Parent unit: 2405 - 2475 MHz Baby unit: 2405 - 2475 MHz Transmit frequency Crystal controlled PLL synthesizer Frequency control Technical specifications Important safety instructions The applied nameplate is located at the bottom of the baby units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Power adapter information:

Parent unit output: 5V DC 1A VTech Telecommunications Ltd. Model: VT05EUS05100 Baby unit output: 6V DC 400mA. VTech Telecommunications Ltd. Model: VT05EUS06040 Rechargeable battery information:

Zhuhai Great Power Energy Co., Ltd. Li-ion battery, 3.6V, 2600mAh, 9.36Wh;

Model: ICR18650-2.6Ah-3.6V-1S1P 8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. Do not overload wall outlets or use an extension cord. 15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 19. You should test the sound reception every time you turn on the units or move one of the components. 20. Periodically examine all components for damage. 21. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 22. Children should be supervised to ensure that they do not play with the product. 23. The product is not intended for use by persons

(including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between 32oF and 104oF. 2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire. 4. WarningStrangulation Hazard Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. 5. Never place the baby unit(s) inside the babys crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket. 6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. Basic operation - Parent unit Overview - Baby unit Use the menu Adjust parent unit speaker volume Zoom Press MENU to enter the menu, or save a setting. You can use the parent unit for advanced settings or operations, such as to play or stop the baby units lullaby, or to adjust the baby units sound sensitivity. VOL+ /

Press parent unit speaker volume. VOL- to adjust your 1. Press MENU when in idle mode. 2. Choose

. 3. Press or to choose

(Zoom in) or

(Zoom out), then press SELECT to confirm your selection. 1 2 3 4 5 6 7 8 n o i t a l u g n a r t S d r a z a H

. n e r d l i h c f o h c a e r f o t u o d r o c s i h t p e e K t e e f e e r h t t s a e l t a e b o t s d e e n d r o c e h T t o n o D

. s e m i t l l a t a d l i h c e h t m o r f y a w a t o n o D

. d r o c n o i s n e t x e n a h t i w e s u

. g a t s i h t e v o m e r e u q s i R t n e m e l g n a r t d i s i o r t s n o m u a r e v u o r t e s t i o d n o d r o c e L

. s t n a f n e s e d n o d r o c e c z e n g o l i

. s p m e t t u o t n e

, e c t e t n a f n e n u d s d e p i s a p z e r i t e r e N

. e g n o l l a r e d s a p z e s i l i t u N e d o g s e i R n i c a l u g n a r t s e e c n a c l a a l l e d a r e u f e b a c e t s e a g n e t n a M r o p r a t s e e b e d e b a c e t s E l i

. s o n s o l e d e c n a c l a a l e d a r e u f i s e p s e r t s o n e m o l

. e t t e u q i t e t t e c e s u o l o N

. o t n e m o m o d o t n e o n i l e d e t i u q o N

. a c i r b m a n l i n i s n e t x e a n u n o c

. a t e u q i t e a t s e Strangulation Hazard Keep this cord out of reach of children. The cord needs to be at least three feet away from the child at all times. Do not use with an extension cord. Do not remove this tag. Risque dtranglement loignez ce cordon des enfants. Le cordon doit se trouver au moins trois pieds dun enfant et ce, en tout temps. Nutilisez pas de rallonge. Ne retirez pas cette tiquette. Riesgo de estrangulacin Mantenga este cable fuera de la alcance de los nios. Este cable debe estar por lo menos tres pies fuera de la alcance del nio en todo momento. No lo use con una extensin inalmbrica. No quite esta etiqueta. 9 10 11 to scroll among While in the menu:

or Press the menu options. or Press to select an item. Press SELECT to confirm your selection. Press TALK/EXIT to exit the menu and return to live view. Submenu Main menu Talk to your baby unit Turn off the screen Press and hold TALK and speak to your parent unit. Your voice is transmitted to the baby unit. Release TALK when done talking and hear your baby again. Press POWER/LCD OFF to switch off the screen. You can still hear sound from the selected baby unit. 1 2 3 4 5 6 Overview - Parent unit 1 2 3 4 5 6 7 8 9 7 8 10 11 9 10 11 12 1 2 3 4 5 Microphone Camera lens Infrared LEDs Light sensor POWER LED light 6 7 8 Night light Night light ON/OFF PAIR hole The parent unit and baby unit(s) provided are already paired. 9 10 11 12 Speaker ON/OFF switch Power jack Slots for wall mounting Need help?

7 8 9 10 POWER/LCD OFF Microphone Power jack RESET Force reboot the parent unit. 11 Speaker For operations and guides to help you using your video monitor, and for latest information and supports, go and check the online help topics and online FAQs. Use your smartphone or mobile device to access our online help. Go to https://phones.vtechcanada.com/manuals; OR Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the devices camera up to the QR code and frame it. Tap the notification to trigger the redirection of the online help.

If the QR code is not clearly displayed, adjust your cameras focus by moving your device closer or further away until it is clear. You can also call our Customer Support at 1 (800) 267-7377 for help. S m Press and hold Tip Press any key on the parent unit to turn on the screen again. 1 2 3 4 Battery LED light 3-level sound indicator light Arrow keys VOL+ /

VOL-

MENU/SELECT 5 6 LINK LED light On when the parent unit is linked to the baby unit. Flashes when the link to the baby unit is lost. TALK/EXIT Press and hold to talk to the baby unit. While in a submenu, press to exit. Whats in the box 1 Connect the baby monitor (contd) 3 Positioning the baby monitor e t i u e e q c r e s o c u o n a p n N o c r a l

. n l a c a a t l o c a s a N i r i e c d a l e a

. b e e l o d b e t m a e d n e l d a a s a

. s p s i p z o r m e r t e i t t t o

. e n n e t e f o o r e D n d l e

. o i r s h h e D c t f t m

. d n o i t d o t r s i a h e l l o c c l a a r a t t n l a e a a o t n e s L n i t r e t r l e r m o u u e e l o n i e

. o s u o t e N t n m a u n

. e m e e f n a e g e e

, n u l g q n s i a r c o l e t l s e d v e a r u t n o n e

. e o r a d t t t R r d f r e n t o s e s e a u p q g g s n f b u f e a m n l s c b e i o s a e i d n

. a e a t p c s o e t i r e E R t t

. e r n s s t e s e o x u e q a i t s t t e e s o a o i g n n i n e u a n e n n t s s e t o m l o e e l c n a e o d l d M u z r e i d s f b o l i n g a t o h e

. g n H t c t a u x t o s e e d h s i a d e t n h r r e o n t c m h e o t v d c t i n z i t e o u e c d s z n d i l e i t e s t t o n d u e g i o d e c i N o p l c a t r s d r i i r f h o y w o m t c a e p e w s u e r e h e T a K S 1 set for VM3254 2 sets for VM3254-2 e t i u e e q c r e s o c u o n a p n N o c r a l

. n l a c a a t l o c Quick start guide s a

. s p s i p z o r m e r t e i t i e c d a s a N i r a l e a

. b e e l o d b e t m a e d n e l d a a t n e s L n i t r e t r l e r m o u u e e l o n i e

. o s u m t n m o t e N a u n

. e e e f n a e g e e

, n u l g q n s i a r c o l e t l s e d v e a r u t n o n e

. e o r a d t t t R r d f r e n t o s e s e a u p q g g s n f b u f e a m n l s c b e i o s a e i d n

. a e a t p c s o e t i r e E R t t

. e r n s s t e s e o x u e q a i t s t t e e s o a o i g n n i n e u a n e n n t s s e t o m l o e e l c n a e o d l d M d c t i n z i t e o u e c d s z n d i l e i t e s t t o n d u e d e c g i o r i N o p l c t t o

. e n n e t e f o o r e D n d l e

. o i r s h h e D c t f t m

. d n o i t d o t r s i a h e l l o c c l a a r a t t n l a e a a o u z r e i d s f b o l i n g a t o h e

. g n H t c t a u x t o s e e d h s i a d e t n h r r e o n a t m h e t c o t v S s d r i i r f h o y w o m t c a e p e w s u e r e h e T a K Charge the parent unit battery When you have connected and turned on the parent unit, the battery will be charged automatically. NOTENotes NOTES Before using the baby monitor for the first time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid

. It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging. The standby time varies depending on the sensitivity level you set, your actual use and the age of the battery. The battery icon indicates the battery status (see the following table). Battery indicators Battery status Action The screen displays light flashes. The

. The battery icon becomes solid

. The battery has very little charge and may be used for only a short time. The battery is fully charged. Charge without interruption (about 30 minutes). To keep the battery charged, connect it to AC power when not in use. 1 Connect the baby monitor 2 Power on or off the baby monitor Slide the ON/OFF switch to power on or off your baby unit. Press and hold POWER to power on or off your parent unit. NOTE NOTES The rechargeable battery in the parent unit is built-in. Use only the power adapters supplied with this product. Make sure the baby monitor is not connected to a switch-controlled electric outlet. Connect the power adapters in a vertical or floor mount position only. The adapters prongs are not designed to hold the weight of a baby monitor, so do not connect them to any ceiling, under-the-

table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the baby units and the power adapter cords are out of reach of children. Caution Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the babys crib or playpen. 3ft (1m)

< 3ft (1m) Caution The default volume of your parent unit is level 3, and the maximum volume is level 5. If you experience high-pitched screeching noise from your baby monitor while positioning:

- Make sure your baby unit and parent unit are more than 3 feet (1 meter) apart, OR

- Turn down the volume of your parent unit. NOTENote NOTES To avoid interference from other electronic devices, place your baby monitor at least 3 feet (1 meter) away from devices such as wireless routers, microwaves, cell phones and computers. 4 Status check Once you power on both your baby unit and parent unit, your parent unit displays image from the baby unit, and the LINK LED light turns on. Press and hold The baby units POWER LED light turns on. Parent unit icons Status icons Connection status or unit and the parent unit. displays when strong signal strength is detected between the baby or displays when moderate or low signal strength is detected between the baby unit and the parent unit. 12 Main menu icons Main Sub-menu menu Zoom Zoom in and out of the video displayed from the baby unit. Main menu Sub-menu Sound Detection Patrol mode Displays when the parent unit is in PATROL mode (For VM3254-2 only). or Current view status Displays the baby unit number of the baby unit that is being viewed. Zoom Displays when the current image on the parent unit has zoomed in. Night vision Displays when the baby unit being viewed has activated the night vision feature. Talkback Displays when talking back to the baby units from parent unit. Lullaby Displays when a lullaby is playing. Night light Displays when the baby units night light is turned on. Mute alert Displays when the parent unit speaker volume is set to zero. Displays when the parent unit is talking to the baby unit. Real-time temperature Displays the real-time temperature detected by the baby unit in Fahrenheit (oF) or Celsius (oC) (e.g. 57 oF or 14 oC). or Settings Temperature Screen off timer The parent unit display will dim to conserve energy after your chosen amount of time of inactivity. Brightness Adjust the parent units LCD screen brightness level. Turn on/off temperature alert tone. Set the parent unit to beep whenever the room temperature detected by the baby unit falls outside of the set temperature range. Battery status displays solid when the battery is fully charged. displays when the battery is low and needs charging. animates when the battery is charging. animates when the battery is charging after it went empty. Set the minimum/maximum temperature. Set temperature display in Fahrenheit (oF) or Celsius (oC). VOX (Voice Activated Alert) Sensitivity You can choose to hear sounds from the baby unit all the time, or to only hear sounds that exceed a certain level. Adjust the microphone sensitivity of your baby unit, the higher the sensitivity level, the more sensitive the baby unit is in detecting sounds to be transmitted to the parent unit. See Sound sensitivity and sound activation section. Sound-activated screen When it is on, and the baby unit detects no sound, the parent unit screen stays off to save power. Once a sound is detected, the parent unit screen and speaker turns on automatically, and you can see and hear your baby. The parent unit will then turn off again after 50 seconds of no sound detection. NOTENote NOTES When the parent unit screen is off and it receives alerts, for example, link lost between parent unit and baby unit, or battery is low, the parent unit screen and speaker will turn on for 10 seconds. Parent unit icons (contd) Sound sensitivity and sound activation Dim mode For VM3254-2 only Mount the baby unit on dry wall (optional) Main menu icons Sub-menu Main menu Lullaby Lullaby volume Adjust the baby units speaker volume when playing the lullaby. Warning icons and messages The battery is empty and needs to be recharged. Battery low at Parent Unit Operation is in progress. The temperature detected by the baby unit is higher than the desired temperature alert range. Select one of the four melodies to play, or stop a lullaby. Temperature too high Night Light Turn on/off the night light. Monitoring Mode (For VM3254-2 only) Patrol mode Monitor your baby in PATROL mode, where the screen will cycle through display videos streamed from all the linked baby units (For VM3254-2 only). View the video from your selected baby units camera. The temperature detected by the baby unit is lower than the desired temperature alert range. Temperature too low No Link to Camera The parent unit is searching for baby units or the link between the baby unit and the parent unit is lost. The parent unit is connected to AC power. Parent Unit Indication Lights LINK On when the parent unit is linked to the baby unit. Flashes when the link to the baby unit being viewed is lost. On when the parent unit is connected to AC power, or the battery is charging. Flashes when the parent unit battery is low and needs charging. Off when the parent unit is disconnected from AC power. Adjust the sound sensitivity of the baby unit You can choose to hear sounds from the baby unit all the time, or to hear sounds that exceed a certain level. You can use the parent unit to adjust the microphone sensitivity of your baby unit. The higher the sensitivity level, the more sensitive the baby unit is in detecting sounds that transmit to the parent unit. The VOX sensitivity level is preset to the highest level. The dim mode is to help you save the parent unit power. Your parent unit display will dim automatically after 10 minutes of inactivity, in which there is neither key pressed nor alert received from the baby unit. 10 min inactivity Status check - Two baby units If you are viewing baby unit As baby unit is not being viewed, its POWER LED light flashes.

, the POWER LED light of baby unit turns on. VOX Sensitivity level Description Highest High Medium Low Lowest The parent unit speaker is constantly on, and you will hear all sounds

(including background noises) from your babys room. The parent unit speaker turns on for soft babbling and louder sounds from your baby. It remains quiet when your baby sleeps soundly. The parent unit speaker turns on for loud babbling and louder sounds from your baby. It remains quiet when your baby makes soft sounds. The parent unit speaker turns on for crying and louder sounds from your baby. It remains quiet when your baby makes soft sounds. The parent unit speaker turns on for loud crying or screeching sounds from your baby. It remains quiet when your baby makes soft sounds. Sound activated screen When sound activation is on, the parent unit screen stays off to save power when the baby unit detects no sound. Once the baby unit detects sounds that are louder than the chosen sound sensitivity level, the parent unit screen turns on automatically. It will then turn off again after 50 seconds of no sound detection. Press any buttons NOTENote NOTES If you power on only one baby unit, your parent unit may display and the LINK LED light will flash. NOTENote NOTES While the screen is dimmed, any keypress or alert message will trigger the screen to return to the preset brightness level. After 10 minutes of inactivity, it will resume to dim mode. Change different views - Patrol Night vision 1. Press MENU when the parent unit is idle. 2. Press 3. Press to choose to choose or or

, then press SELECT to confirm your selection. 10s Change different views - Single-cam Items to purchase You will need to purchase the following items separately to mount your baby unit:

2 screws 2 anchors NOTENote NOTES The types of screws and anchors you need depend on the composition of the wall. NOTENote NOTES Check for reception strength and camera angle before drilling the holes. Use a pencil to mark two holes in parallel. Make sure they are the same distance apart as the wall mount holes on the baby unit. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. Align the wall mount holes on the baby unit with the screws on the wall. Slide the baby unit down until it locks into place. 1. Press MENU when the parent unit is idle. or 2. Press 3. Press or you would like to view. to choose to choose between and

, then press SELECT to confirm the baby unit Drill two holes in the wall ( 7/23 inch drill bit ). If you drill the holes into a stud, go to step 3.

-OR-

If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall. Adjust the camera angle. The baby unit has infrared LEDs that allow you to see your baby clearly at night or in a dark room. When the baby unit being viewed detects low light levels, the infrared LEDs are switched on automatically. The images from the baby unit are in black and white, and appears on the screen. Notes It is normal to see a short white glare on your parent unit screen as the baby unit is adapting to the dark environment. When the infrared LEDs are on, the images are in black and white. This is normal. Tip Depending on the surroundings and other interfering factors, like lighting, objects, colors and backgrounds, the display resolution may vary. Adjust the baby units angle or place the baby unit at a higher level to prevent glare and blurry display. How do you get warranty service?

To obtain warranty service in Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and 2. Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase. Frequently asked questions Below are the questions most frequently asked about the baby monitor. Why does the baby monitor not respond normally?

Why dont the power-on light of the baby unit and parent unit go on when I switch on the units?

Why doesnt my parent unit charge while connected to AC power?

Try the following (in the order listed) for common cure:

1. Disconnect the power to the baby units and the parent unit. 2. Wait a few seconds before connecting power back to the baby units and the parent unit. 3. Turn on the baby units and the parent unit. 4. Wait for the parent unit to synchronize with the baby units. Allow up to one minute for this to take place. Perhaps the parent unit is not connected to the power. Insert the appliance plug into the parent unit and put the adapter in a wall socket. Then, press and hold POWER to switch on the parent unit and to establish connection with the baby unit. Perhaps the baby unit is not connected to the power. Insert the appliance plug into the baby unit and put the adapter in a wall socket. Then, slide the ON/OFF switch to ON to switch on the baby unit and to establish connection with the parent unit. Make sure the power is not controlled by a wall switch. You may have used the battery for a long time. See Warranty for repair/replacement. Why is my screen in black and white?

The screen is in black and white during night-time or in a dark room when the night vision feature is activated. This is normal. Why do I get glare or blurry display on my screen when viewing my baby at night?

During night-time or in a dark room, the surroundings and other interfering factors, like lightings, objects, colors and backgrounds may affect the image quality on your parent unit screen. Adjust the baby units angle or place the baby unit at a higher level to prevent glare and blurry display. Why does the baby monitor produce a high-pitched noise?

The parent unit and baby units may be too close to each other. Move the parent unit away from the baby units until the noise stops; OR Turn down the volume of your parent unit. Why does the parent unit beep?

The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). Why does the parent unit react too quickly to other sounds?

Why dont I hear a sound/Why cant I hear my baby cry?

Why cant I establish a connection? Why is the connection lost every now and then? Why are there sound interruptions?

The parent unit may not have enough charge for the parent unit to perform normally. Charge the battery in the parent unit until the battery icon becomes solid

. The temperature of your babys room may be too high or too low. The baby unit also picks up other sounds than those of your baby. Adjust the VOX sensitivity level to a lower level or lower the parent unit speaker volume. The parent unit speaker volume may be too low. See Adjust parent unit speaker volume to increase the volume. You may have set a low VOX sensitivity level. See Adjust the sound sensitivity of the baby unit to set to a higher level. The baby units may be out of range. Move the parent unit closer to the baby units (but not less than 3 feet). Other electronic products and wireless products may cause interference with your baby monitor. Try installing your baby monitor as far away from these devices as possible. If you power on only one baby unit, your parent unit may display LED light will flash.

, and the LINK The RBRC seal The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Li-ion batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation makes it easy for you to drop off the spent battery at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY are registered trademarks of Call2recycle, Inc. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The baby unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. Limited warranty What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will replace at VTechs option, without charge, a Materially Defective Product. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the replacement Products to you in working condition. You should expect the replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE

(1) YEAR from the date of purchase (90 days on products purchased as Refurbished*). This limited warranty also applies to the replacement Product for a period of either (a) 90 days from the date the replacement Product is shipped to you or (b) the time remaining on the original one-year warranty (90-day limited warranty on products that are purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store carry a 90-day replacement warranty. What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit.

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5480361.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case Bay Area Compliance Laboratories Corp. (Shenzhen) Project No.: SZ1210906-46304E-RF EXHIBIT A - FCC ID LABEL AND LOCATION FCC ID Label Label Location on EUT The label shown shall be permanently affixed at a conspicuous location on the device and be readily visible to the user at the time purchase (Labeling requirements per 2.925)

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5480357.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com FCC Confidential Authorization Date: 2021/09/08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Confidentiality Request regarding application for certification of FCC ID: EW780-1960-00A In accordance with Sections 0.457 and 0.459 of the Commissions Rules, VTech Telecommunications Ltd hereby requests long-term confidential treatment of information accompanying this application as outlined below:

Block Diagram Schematics Operation Description The above materials contain proprietary and confidential information not customarily released to the public. The public disclosure of these materials provides unjustified benefits to its competitors in the market. Sincerely Yours, Signature Michael Tsui Approbation Supervisor

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5480356.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case VTech Telecommunications Ltd Add: 23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT, Hong Kong Telephone: (852)2680 5398 Fax: (852)2680 5252 E-mail: Michael_Tsui@vtech.com FCC Authorization Date: 2021/09/08 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Subject: Agent Authorization To whom it may concern:

We, VTech Telecommunications Ltd, the undersigned, Hereby authorizes Bay Area Compliance Laboratories Corporation (Shenzhen)to act on its behalf in all matters relating to application for Equipment authorization, including the signing of all documents relating to these matters. All acts carried out by Bay Area Compliance Laboratory Corporation(Shenzhen) on our behalf shall have the same effect as our own action. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. This authorization is valid until further written notice from the applicant. Sincerely Yours, Signature Michael Tsui Approbation Supervisor QA-FR-170-B

WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/5480358.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case VTech Telecommunications Ltd Sep 02, 2021 To whom it may concern, Multiple Models Confirmation Letter-BU I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows:

Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout

(Others, please specify) The only differences between these models are the follows for marketing purpose:

Color Cosmetic details Trade name Model Number

(Others, please specify) Suffix (a, b) represents Color code Packing configuration Others, please specify) . a=any alphanumeric character or blank is presenting number of baby unit. b = any alphanumeric character or blank is presenting color of enclosure. For the product subject to authorization under FCC Declaration of Conformity:

In addition, it is to confirm that all the below information 1) the U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual are the same but different in the following model numbers only:

Item No. New model 1 2 3 YES YES YES Model Number VM3254 BU VM3254-2 BU VM3254-ab BU Trade Name vtech vtech vtech 1 baby unit 2 baby unit a baby unit Remarks The sample being submitted to Bay Area Compliance Labs Corp.(Shenzhen) for conformity assessment is VM3254 BU (test model) of the above list. All above model's FCC ID is EW780-1960-00A, IC is 1135B-80196000A. Regards, Michael Tsui Approbation Supervisor