FCC ID: EW780-1924-00 Video Monitor

RM5754HD/RM5754-2HD RM5764HD/RM5764-2HD RM5864HD/RM5864-2HD RM7754HD/RM7754-2HD RM7764HD/RM7764-2HD Important safety instructions The applied nameplate is located at the bottom of the baby units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Parent unit power adapter:

Output: 5V DC 1000mA;

Camera unit power adapter:

Output: 5V DC 1000mA. 8. The power adapter is intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-

table or cabinet outlet. 9. For pluggable equipment, the socket-outlet

(power adapter) shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 13. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 14. The equipment is to be supplied from an identified USB port complying with the requirements of Limited Power Source. 15. Do not overload wall outlets or use an extension cord. 16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 20. You should test the sound reception every time you turn on the units or move one of the components. 21. Periodically examine all components for damage. 22. Be aware of possible loss of privacy while using public airwaves. Conversations may be picked up by other nursery monitors, cordless phones, scanners, etc. 23. Children should be supervised to ensure that they do not play with the product. 24. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children. 25. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions Use and store the product at a temperature between 32oF and 104oF. Burn hazard, fire hazard, explosion hazard associated with mishandling of the battery. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. WarningStrangulation Hazard Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. Never place the camera unit(s) inside the babys crib or playpen. Never cover the camera unit(s) or parent unit with anything such as a towel or a blanket. Other electronic products may cause interference with your camera unit. Try installing your camera unit as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. The RBRC seal The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The RBRC program provides a convenient alternative to placing used lithium-ion batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation in RBRC makes it easy for you to drop off the spent battery at local retailers participating in the RBRC program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. RBRC and 1 (800) 8 BATTERY are registered trademarks of the Rechargeable Battery Recycling Corporation. FCC and IC regulations FCC Part 15 NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The camera unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in (20 cm) or more. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/

receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. RF radiation exposure statement The camera unit complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The camera unit should be installed and operated with a minimum distance of 8 in (20 cm) between the main unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. California Energy Commission battery charging testing mode This HD video monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your HD video monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to camera units, the CEC battery charging testing mode is activated while it is powered off and charging. For cETL compliance only Mesures de scurit importantes La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent:

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. 2. Linstallation par un adulte est requise. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilit du parent ou de la personne qui soccupe de lenfant. Ce produit pourrait cesser de fonctionner et, par consquent, vous ne devriez pas prsumer quil continuera de fonctionner correctement pendant une priode de temps donne. De plus, il ne sagit pas dun instrument mdical et ne devrait pas tre utilis comme tel. Ce produit est destin vous aider superviser votre bb. 5. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque dexplosion pourrait survenir si un mauvais type de pile est utilis pour lunit du parent. La pile ne peut pas tre soumise des tempratures extrmes leves ou basses et une faible pression dair haute altitude pendant lutilisation, lentreposage ou le transport. Llimination de la pile dans le feu ou dans un four chaud, ou lcrasement ou le dcoupage mcanique de la pile peuvent entraner une explosion. Laisser la pile dans un environnement temprature extrmement leve peut entraner une explosion ou la fuite dun liquide ou dun gaz inflammable. Une pile soumise une pression dair extrmement basse peut provoquer une explosion ou une fuite de liquide ou de gaz inflammable. liminer la pile usage conformment aux informations du Sceau RBRC. 7. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. Adaptateur de lunit du parent:

Sortie : 5 V CC 1000mA. Adaptateur secteur de la camra :

Sortie : 5 V CC 1000mA. 8. Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. 9. Pour les appareils raccords, la prise de courant

(de ladaptateur secteur) doit tre installe prs de lquipement et doit tre facilement accessible. 10. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 11. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. 12. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 13. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 14. Lquipement doit tre fourni partir dun acquiescement gauche identifi dUSB aux conditions de la source dnergie limite. dexplosion associ une mauvaise manipulation de la batterie. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Assurez-vous que le moniteur et le cordon de ladaptateur sont toujours hors de porte des enfants, au moins 1 mtre (3 pieds) de lenfant ou du berceau, pour viter tout risque de strangulation. 15. Ne surchargez pas les prises de courant murales ni Ne jamais placer le moniteur lintrieur du les rallonges lectriques. 16. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 17. Les trous et ouvertures du botier, situs larrire berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. Dautres produits lectroniques peuvent causer des de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 18. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 19. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 20. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 21. Examinez les composantes afin de vrifier si celles-

ci ne sont pas endommages. 22. Soyez avis de la perte de la confidentialit lorsque vous utilisez les ondes publiques. Les conversations peuvent tre entendues par dautres moniteurs de bb, des tlphones sans fil, des scanneurs, etc. 23. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. 24. Les petites pices de ce moniteur peuvent tre avales par les bbs ou les petits enfants. Veuillez tenir ces pices hors de porte des enfants. 25. Le produit nest pas conu pour tre utilis par des personnes (incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde Utilisez et entreposez le produit une temprature entre 0 C (32F) et 40C (104 F). Risque de brlure, risque dincendie, risque interfrences auprs de votre camra IP. Essayez dinstaller votre camra IP le plus loin possible de ces dispositifs lectroniques : routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs de pices, tlviseurs, ordinateurs personnels, appareils lectriques de cuisine et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil):

Lorganisme Wireless Technology Research, LLC

(WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1 2020 VTech Communications, Inc. All rights reserved. 01/20. RM57X4_77X4_II_V4 Document order number: 96-012901-040-100

Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. Whats in the box Your HD video monitor package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Overview Camera unit overview Parent unit overview Congratulations on purchasing your new VTech product. Before using this HD video monitor, please read Important safety instructions. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, visit www.vtechcanada.com. What does HD Video Monitor do?

VTech 7-inch Smart Wi-Fi 1080p Video Monitor allows you to stay close to your baby when you are on the move or away. This monitor is Wi-Fi enabled, which uses your home wireless network to stream live video and audio through the HD camera unit and 7-inch color screen parent unit. It allows you to maintain a constant connection to your baby. You can also monitor from your smartphone and mobile tablet. VTech 7-inch Smart Wi-Fi 1080p Video Monitor uses MyVTech Baby 1080p app to let you instantly see and hear whats happening with your baby from anywhere in the world. The app can be downloaded from the App Store or the Google PlayTM Store, directly from your smartphone or mobile tablet. Installation guide Quick start guide Important safety instructions 1 2 3 4 x 2 x 2 Requirements For mobile access:

Network Wi-Fi router Internet connection 1 2 3 Wi-Fi 2.4GHz 802.11 b/g/n 4 5 6 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload bandwidth per camera 7 MyVTech Baby 1080p mobile app Connect up to 10 camera units 1 2 3 5 6 7 8 9 10 11 4 Infrared LEDs Allow you to see clearly in a dark surrounding. 8 12 13 1 2 3 4 5 6 7 8 9 Light sensor Camera lens Microphone 5 6 7 Speaker 9 10 11 Press to turn the night light on or off. LED indicator Red is steady on when the camera unit is connecting to the parent unit directly in local mode. Green is steady on when the camera unit and parent unit are connecting to your home Wi-Fi network via the Wi-Fi router. Flashes red slowly during video streaming in local mode. 12 13 Flashes green slowly during video streaming via home Wi-Fi network. ON Power on/off switch. PAIR Reset the camera unit to factory default. 1. Press and hold PAIR key until you hear a beep sound. 2. Release the PAIR key, and then press the PAIR key again five times until you hear another beep sound. 3. The camera unit will sound another beep when the reset completes. Then, the camera unit will reboot. Temperature sensor Night light Power jack 10 11 12 13 Slots for wall mounting Wall mount bracket is included in your package. 8 9 10 11 12 13 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 LINK LED light On when the parent unit is linked to the 6 Arrow keys

, or Flashes when the link to the camera unit camera unit. is lost. LED light 1 2 3 4 5 On when the parent unit is connected to AC power, or the battery is charging. Off when the parent unit is disconnected from AC power, or when the parent unit is connected to AC power and the battery is fully-charged. Flashes when the parent unit battery is low and needs charging. 3- level sound indicator light Green on when low sound level is detected by the camera unit. Green and amber on when moderate sound level is detected by the camera unit. Green, amber and red on when high sound level is detected by the camera unit. TALK Press and hold to talk to the camera unit. While in a submenu, press to exit. Press to zoom in/out. Press to navigate leftward, upward, rightward or downward, within the main menu and submenus. While viewing image from the camera unit, press to pan the camera unit leftward, upward, rightward or downward. While viewing zoomed image, press to move the zoomed image leftward, upward, rightward or downward. MENU/SELECT Press to enter the main menu. While in a menu, press to choose an item, or save a setting.

- VOL/ VOL +

Increase or decrease parent units RESET Force reboot the parent unit. 7 8 10 11 12 14 15 volume. 9 Microphone POWER key Power jack 13 Antenna Speaker Stand How the system works Protect your privacy and online security 1 Connect, charge and power on the baby monitor Local mode The Parent unit and the camera unit of your video monitor connect to each others in Local mode by default, which allows you to stream live video right out of the box. Local mode connection lets you stream live video from parent unit only. You may experience reduced signal strength if your parent unit and camera unit are far apart, or there are obstructing factors, such as internal walls, between them. Move the parent unit closer to the camera unit to improve the signal strength. You can also set up Remote mode to connect via your home Wi-Fi network to improve the connection between your parent unit and camera unit. Remote mode You can continue using your video monitor with Local mode connection, or you can set up your monitor in Remote mode connection. Remote mode uses your home Wi-Fi network to connect your video monitor. It supports streaming live video through parent unit and smartphone app. We recommend that you set up your monitor in Remote mode to enjoy streaming live video via your parent unit with better connection. If you want to stream live video remotely with your mobile device, download and install the MyVTech Baby 1080p mobile app. With the mobile app, your Wi-Fi router (not included) provides Internet connectivity to your HD video monitor system. It serves as a communicating channel between your camera unit and mobile device, allowing you to monitor and/or control your camera unit wherever you are. For detail, see Mobile access section in the quick start guide.

- Does not contain dictionary words or personal information. Charge the parent unit battery Connect the baby monitor The rechargeable battery in the parent unit is built-in. Use only the power adapters supplied with this product. Make sure the parent unit and the camera unit are not connected to the switch controlled electric outlets. Connect the power adapters in a vertical or floor mount position only. The adapters prongs are not designed to hold the weight of the parent unit and the camera unit, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the camera unit and the power adapter cords are out of reach of children. To maintain compliance with the FCCs RF exposure guidelines, place the camera unit at least 20cm from nearby persons. The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, keep the parent unit connected to AC power. With the battery alone, the parent unit can cordlessly run for a short time only. VTech cares about your privacy and peace of mind. Thats why weve put together a list of industry-recommended best practices to help keep your wireless connection private and your devices protected when online. We recommend you carefully review and consider complying with the following tips. Ensure your wireless connection is secure. Before installing a device, ensure your routers wireless signal is encrypted by selecting the WPA2-PSK with AES setting in your routers wireless security menu. Change default settings. Change your wireless routers default wireless network name (SSID) to something unique. Change default passwords to unique, strong passwords. A strong password:

- Is at least 10 characters long.

- Is complex.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers. Keep your devices up to date. Download security patches from manufacturers as soon as they become available. This will ensure you always have the latest security updates. If the feature is available, enable automatic updates for future releases. Disable Universal Plug and Play (UPnP) on your router. UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network devices to open inbound ports without any intervention or approval from you. A virus or other malware program could use this function to compromise security for the entire network. For more information on wireless connections and protecting your data, please review the following resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips www.fcc.gov/consumers/guides/how-protect-yourself-online. 2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet www.us-cert.gov/ncas/tips/ST15-003. 3. Federal Trade Commission: Using IP Cameras Safely https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely. 4. Wi-Fi Alliance: Discover Wi-Fi Security http://www.wi-fi.org/discover-wi-fi/security. Your parent unit detects the connection signal strength. If you have connected your video monitor with your home Wi-Fi network, your parent unit automatically switches to local or remote mode - the one that has stronger signal strength. Slide the ON switch to power on or off your camera unit. Power on Power off 1 Connect, charge and power on the baby monitor (Contd) 2 set up the hd video monitor for mobile access (optional) 4 Test the sound level and position the HD video monitor Raise the parent unit antenna for better reception 2. Adjust the angle of the camera to aim at your baby. After you have connected the parent unit and the camera unit, you can stream live video in local mode right away. You can also set up connection between your HD video monitor system and your home Wi-Fi network for better connection between the parent unit and camera unit. You can also download and install the MyVTech Baby 1080p mobile app to stream video remotely. For detail, refer to the quick start guide included in your package. should not be used as such. This HD video monitor is intended as an aid. It is not a substitute for proper adult supervision, and Testing the sound level of the HD video monitor HD video monitor setup for mobile access:

Set up Wi-Fi connection Pair camera to mobile device To install MyVTech Baby 1080p mobile app:

Browse the App Store store keyword myvtech baby 1080p.

, and search for the mobile app with the or the Google Play OR Scan the QR code to get the app. If you plan to install your camera unit in a designated location, and use your home Wi-Fi network to connect your video monitor, you need to test which of your selected monitoring areas within the house have good Wi-Fi signal strength. After you have powered on your parent unit, you can use your parent units Wi-Fi signal strength indicator to assist in checking. Once you have identified the suitable location, you can install your camera unit. Adjust the distance between your camera unit and the Wi-Fi router if needed. Depending on surroundings and obstruct-

ing factors, such as the effect distance and internal walls have on signal strength, you may experience reduced Wi-Fi signal. To improve the Wi-Fi signal strength, adjust the distance or direction of your parent unit. Check with your parent unit again. Charge the battery before use The parent unit is fully charged after 8 hours of continuous charging. The standby time varies depending on your actual use. After the parent unit is fully charged, press POWER until the welcoming screen appears. 3 test the location for the camera unit The battery icon indicates the battery status (see the following table). Battery indicators Battery status Action The screen displays and

. The light flashes. The battery has very little charge and may be used for only a short time. Charge without interruption (about 30 minutes). The battery icon becomes solid

. The battery is fully charged. To keep the battery charged, connect it to AC power when not in use. mount the camera unit (optional) NOTENotes NOTES Check for reception strength and camera angle before drilling the holes. The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the screws and anchors separately to mount your camera units. 1. Place the wall mount bracket on a wall and then use a pencil to mark two holes in parallel. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit). 3. Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole first, so that the wall mount bracket position is fixed. You can tighten the other screw in the top hole. 4. Place the camera unit on the wall mount bracket, and then slide it forward until it locks into place. Connect the power adapter to the camera unit and a power supply not controlled by a wall switch. 2. If you drill the holes into a stud, go to step 3. If you drill the holes into an object other than a stud, insert the wall anchors into the holes. Tap gently on the ends with a hammer until the wall anchors are flush with the wall. 3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. OR 4. Place the camera unit on the wall mount bracket, and then slide it forward until it locks into place. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place. 2 1 5. You can maximize your camera units viewing angles by tilting the wall mount bracket. Hold the camera unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your camera unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle. For hearing protection, make sure the parent unit is more than 10 feet

(3 meters) away from the camera unit. If you hear any high-pitched noise from the parent unit, move the parent unit further until the noise stops. You can also press - VOL on the parent unit to lower or mute the noise. Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the camera unit. Positioning the HD video monitor 37 10:25 AM

> 3m

> 1m Keep the camera unit out of the reach of your baby. Never place or mount the camera unit inside the babys crib or playpen. 1. Place the camera unit more than 3 feet (1 meter) away from your baby. 3. To avoid causing high-pitched screeching noise from your HD video monitor:

Make sure your camera unit and parent unit are more than 10 feet (3 meters) apart;

OR Turn down the volume of your parent unit.

> 3m

< 3m General product care Limited warranty To keep this product working well and looking good, follow these guidelines:

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors or fluorescent lamps). DO NOT expose it to direct sunlight or moisture. Avoid dropping the product or treating it roughly. Clean with a soft cloth. DO NOT immerse the parent unit and the camera unit in water and do not clean them under the tap. DO NOT use cleaning spray or liquid cleaners. Make sure the parent unit and the camera unit are dry before you connect them to the mains again. Storage When you are not going to use the HD video monitor for some time, store the parent unit, the camera unit and the adapters in a cool and dry place. Can I turn off the parent unit screen but keep hearing sound from the camera unit?

Why does the camera unit not respond normally?

Frequently asked questions Below are the questions most frequently asked about the HD video monitor. If you cannot find the answer to your question in the below table, visit our website at www.vtechphones.com, or call 1-844-848-8324 (1-844-84-VTECH) for customer service. In Canada, go to www.vtechcanada.com or call 1-888-211-2005. The parent units LCD display will dim automatically after being inactive for some time. Press MENU/SELECT will turn the LCD display back on. Try the following (in the order listed) for common cure:

1. Disconnect the power to the camera unit. 2. Wait a few minutes before connecting power back to the camera unit. 3. Reboot the parent unit. Why is my screen in black and white?

The camera unit has a light sensor that measures the ambient light. When the ambient light is dim, such as during nighttime or in a dark room, the camera activates its infrared LEDs, and displays the camera view in black and white. Why does my camera show offline? Why is the connection lost every now and then?

Why dont I hear a sound/Why cant I hear my baby cry?

The camera unit may lose the Internet connection. Check your network and the router setting. Other electronic products may cause interference with your camera. Try installing your camera as far away from these electronic devices as possible. The parent unit speaker volume may be too low. Press VOL + to increase the volume. You may have set a low sound sensitivity level. Set the sound sensitivity to a higher level. For details, go to www.vtechphones.com for online help topics. What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will repair or replace at VTechs option, without charge, a Materially Defective Product. If we repair the Product, we may use new or refurbished replacement parts. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Repair or replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the repaired or replacement Products to you in working condition. You should expect the repair or replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase. If VTech repairs or replaces a Materially Defective Product under the terms of this limited warranty, this limited warranty also applies to the repaired or replacement Product for a period of either (a) 90 days from the date the repaired or replacement Product is shipped to you or (b) the time remaining on the original one-year warranty; whichever is longer. What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, representative of VTech; or systems; or altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 on the following part); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1-844-848-8324

(1-844-84-VTECH). In Canada, go to www.vtechcanada.com or call 1-888-211-2005.NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return repaired or replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. If the Product failure is not covered by this limited warranty, or proof of purchase does not meet the terms of this limited warranty, VTech will notify you and will request that you authorize the cost of repair prior to any further repair activity. You must pay for the cost of repair and return shipping costs for the repair of Products that are not covered by this limited warranty. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and 2. Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/Provincial Law Rights:

This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase.

Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. RM7754HD RM7754-2HD 7-inch Smart Wi-Fi 1080p Video Monitor VTech 7-inch Smart Wi-Fi 1080p Video Monitor allows you to stay close to your baby when you are on the move or away. This monitor is Wi-Fi enabled. At best, it uses your home wireless network to stream live video and audio through the HD camera unit and 7-inch color screen parent unit. It allows you to maintain a constant connection to your baby. You can also monitor from your smartphone and mobile tablet. VTech 7-inch Smart Wi-Fi 1080p Video Monitor uses MyVTech Baby 1080p app to let you instantly see and hear whats happening with your baby from anywhere in the world. The app can be downloaded from the App Store or the Google PlayTM Store, directly from your smartphone or mobile tablet. Quick start guide Document order number: 96-012894-010-100 12/19. RM7754-XHD_QSG_V1. 2019 VTech Communications, Inc. All rights reserved. Specifications are subject to change without notice. Basic operation Connect and charge the parent unit battery before use. See the installation guide for detail. After the parent unit is fully charged, press POWER until the welcoming screen appears. After powering up your video monitor, the parent unit streams live video in local mode. We recommend you follow the instructions on screen to set up home Wi-Fi network with your monitor for functionality enhancements and mobile access. See Auto software and firmware update and Download app for mobile access in this quick start guide. For more information on Local mode and Remote mode, see the installation guide. Use the menu Press MENU on the parent unit to enter the main menu, choose a menu item, or save a setting. You can use the parent unit menu for advanced settings or operations, such as to play or stop lullaby, or adjust the sound detection setting. While in the menu:

Press

, or options. to scroll among the menu Press SELECT to select an item. Press TALK to return to the live video. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. App Store is a trademark of Apple Inc., registered in the U.S. and other countries. Android TM and Google Play TM are trademarks of Google Inc. C22.2 NO.62368-1 CSA STD. CERTIFIED TO 62368-1 UL STD. CONFORMS TO Adjust speaker volume Press -VOL / VOL+ to adjust your parent unit speaker volume. It determines the volume of sound transmitted from your camera unit. Muted Talk to your baby via the camera unit 1. Press and hold the TALK key. 2. When the icon displays on screen, speak to your parent unit. Your voice is transmitted to the camera unit. 3. When finish talking, release the TALK key and hear your baby again. Turn on/off camera's status LED You may set the status LED indicator of your camera unit on or off. Go to

> Status LED. Press and hold Connection status The following icons shown in the parent unit indicate the connection status:

Local mode connection - indicates the signal strength when the parent unit and camera unit connect directly. Zoom Press to zoom in or out. Wi-Fi router connection - indicates the signal strength when the parent unit and camera unit connect to the home Wi-Fi network. You can reset the parent unit by pressing the RESET key at the back of the unit. Use a pin and insert it into the hole on the back of the parent unit, and then press the button inside. Auto software and firmware update Download app for mobile access To ensure that your HD video monitor is always at its best performance, the parent unit will prompt a message and ask you to update its software and the camera unit's firmware when there are new versions available. Follow the instructions on the parent unit screen to update your HD video monitor. If you skip the updates, the parent unit and camera unit will be updated automatically when the parent unit is powered off, and then powered on again. Connect your HD video monitor with home Wi-Fi network You must connect your video monitor to your secured home Wi-Fi network in order to receive the latest software and firmware updates. To set it up, go to

> Configure Wi-Fi. Get help with the online topics RM7754HD online help Driven by system updates, the software, online help topics, and online FAQs will be updated periodically. For latest information and supports, go and check the online help topics and online FAQs. Use your smartphone or mobile device to access our online help. Go to https://help.vtechphones.com/rm7754hd or scan the QR code on the right. If you would like to contact us, visit https://help.vtechphones.com/cs/rm7754hd. 1 You can download the free MyVTech Baby 1080p mobile app and install it to a mobile device, then use your mobile device and the mobile app to monitor your areas remotely. 1. Press MENU when the parent unit is idle, then go to

> Download Mobile App. 2. Scan the QR code in the parent unit to download the app into your mobile device. 3. Follow the instructions in the mobile app to set up and pair your camera unit to the mobile app. Alternatively, you can download the mobile app from the App Store or Google Play store. Install MyVTech Baby 1080p mobile app 1. Browse the App Store 2. Search for the mobile app with the keyword myvtech baby 1080p. 3. Download and install the MyVTech Baby 1080p mobile app to your or the Google Play store

. mobile device. OR Scan the QR codes below to get the app. 2 After installing the mobile app, follow the instructions in the mobile app and parent unit to set up and pair your camera unit. In your mobile device:

camera account. 1. Tap to run the mobile app in your mobile device, and then create a 2. We recommend that you use common webmail services, such as Google Gmail for registration of your camera account. Check your email (and Spam folder), and activate your new camera account via the email link, then sign in to your account. 3. Follow the instructions in the mobile app to pair the camera. Tap + in the mobile app to get started. in the camera list to display In the mobile app, tap the side menu, and then tap Help to go to our online support and read the online help topics for operation instructions. You can also scan the QR code on the right, or go to https://help.vtechphones.com/rm7754hd, to read the online help topics in a web browser. RM7754HD online help Make sure your mobile device meets the minimum requirement for the mobile app. Minimum requirement The mobile app is compatible with:

AndroidTM 5.0 or later; and iOS 8.0 or later. Driven by Android and iOS updates, MyVTech Baby 1080p mobile app, online help topics, and online FAQs will be updated periodically. Download and install the latest mobile app. For latest information and supports, go and check the online help topics and online FAQs.

a) b) c) d) e) f) g) SGS North America Inc. 620 Old Peachtree Road SUITE 100 Suwanee, Georgia 30024 United States Applicant Declaration Applicant Legal Business Name VTech Telecommunications Ltd 23/F Tai Ping Ind Center Block 1, 57 Ting Kok Rd, Tai Po NT, Hong Kong Address Grantee Code FCC ID Contact Email Contact Phone Authorized Contact Name Mr. Michael Tsui EW7 80-1924-00 michael_tsui@vtech.com 852-26805398 I, the undersigned, certify that I am an authorized signatory for the Applicant and therefore declare;

in accordance with 47CFR2.911(d), all of the statements herein and the exhibits attached hereto are true and correct to the best of my knowledge and belief. in accepting a Grant of Equipment Authorization issued by a TCB, under the authority of the FCC, as a result of the representations made in this application, the Applicant is responsible for:

labeling the equipment with the exact FCC ID as specified in this application,

(1)

(2) compliance statement labeling pursuant to the applicable rules,

(3) compliance of the equipment with the applicable technical rules, if the Applicant is not the actual manufacturer of the equipment, appropriate arrangements have been made with the manufacturer to ensure that production units of this equipment will continue to comply with the FCCs technical requirements. in accordance with 47 CFR 2.909 and KDB394321, the Applicant has read, understood and agrees to accept that they are the responsible party and agree to abide by their responsibilities as specified under 47 CFR 2.909 and KDB394321. in accordance with ISO17065, FCC KDB641163, FCC KDB610077, KDB394321 and RSP-100, the Applicant has read, understood, accepts and agrees to abide by the post market surveillance requirements.

(1)

(2)

(3) the Applicant understands, accepts and agrees that a sample may be requested for surveillance testing. the Applicant shall make provisions to always have a production sample available upon request by SGS, FCC and/or ISED. the Applicant shall, upon request by SGS, at the Applicants expense, provide a production sample of the requested product to SGS, FCC and/or ISED as instructed. The sample shall include all support devices, cables, software, accessories or other hardware or software required for evaluation, review, certification and audit surveillance of products certified by SGS. neither the Applicant nor any party to the application is subject to a denial of Federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862 because of a conviction for possession or distribution of a controlled substance. See 47CFR 1.2002(b) for the definition of a party for these purposes. the Applicant has read, understood, accepts and agrees to abide by the SGS North America, Inc.(TCB) terms and conditions. Link to CFRs: https://www.fcc.gov/wireless/bureau-divisions/technologies-systems-and-innovation-division/rules-regulations-title-47 Link to KDBs: https://apps.fcc.gov/oetcf/kdb/index.cfm Link to RSP-100: https://www.ic.gc.ca/eic/site/smt-gst.nsf/eng/sf01130.html Applicant Signature:

Date: Oct. 23, 2020 Print Name:

Title:

Michael Tsui Approbation Supervisor

*NOTE: This declaration cannot be signed by an Agent, it shall be signed by an authorized person listed in the FCC database Applicant Declaration Rev:0.0

VTech Telecommunications Ltd Request for Class II Permissive Change FCC ID EW780-1924-00 DateJan. 04, 2021 TOFederal Communication Commission Please be notified that wethe undersignedVTech Telecommunications Ltd declare that the reasons for this Class II permissive change are as below External appearance is slightly changed;

Power PCB changed from USB type C to DC jack;

Temperature sensor changed from external to internal;

VTPL adaptor VT05EUS05100 change from type C to DC jack;

remove adaptor Ten Pao S005CAU0500100. VTech Telecommunications Ltd According to the changes above, just partial sensor and Power PCB layout interface were change, Hence, Conducted Disturbance at AC Power Line; Conducted Peak Output Power and Radiated Emission were re-evaluated, and then C2PC was requested in this application. Thank you. Sincerely. ________Michael Tsui_______

(Print name) By:

(Signature1) _________________________ Title:

On behalf of:

Telephone: _____852-26805398_________________ ________Approbation supervisor_________________ _____ VTech Telecommunications Ltd______________

23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT Hong Kong To:

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: VTech Telecommunications Ltd Regarding: Confidentiality Request regarding application for FCC ID: EW780-1924-00 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. N/A The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos Sincerely, Print Name: Michael Tsui Signature:

On behalf of Company: VTech Telecommunications Ltd Telephone: 852-26805398 E-mail: michael_tsui@vtech.com Title: Approbation Supervisor

VTech Telecommunications Ltd Oct. 23, 2020 To whom it may concern, Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows:

Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout

(Others, please specify) The only differences between these models are the follows for marketing purpose:

Color Cosmetic details Trade name Model Number

(Others, please specify) Suffix (a, b,x) represents Color code Packing configuration Others, please specify) a= any alphanumeric character or blank is presenting number of baby unit. b = any alphanumeric character or blank is presenting color option For the product subject to authorization under FCC Declaration of Conformity:

In addition, it is to confirm that all the below information 1) the U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual are the same but different in the following model numbers only:

Item No. Model Number Remarks Trade Name vtech 1 2 3 RM5754 BU RM5754HD BU RM5754-2HD BU RM5754-aHD BU RM5854 BU RM5854HD BU RM5854-aHD BU VM813HD BU VM813-1bHD BU VM813-abHD BU 4 5 6 7 8 9 10 11 RM7754 BU 12 RM7754HD BU 13 RM7754-2HD BU 14 RM7754-aHD BU 15 RM7854 BU 16 RM7854HD BU Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 2 Baby units Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit, b color option Same as RM7754HD BU a Baby units, b color option Same as RM7754HD BU 1 Baby unit 1 Baby unit

Same as RM7754HD BU 2 Baby units Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit VTech Telecommunications Ltd 17 RM7854-2HD BU 18 RM7854-aHD BU 19 20 21 VM816HD BU VM816-1bHD BU VM816-abHD BU Same as RM7754HD BU 2 Baby units Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit, b color option Same as RM7754HD BU a Baby units, b color option Regarding:

IC: 1135B-80192400 HVIN: 35-400255BU The sample being submitted to Intertek Testing Services for conformity assessment is RM7754HD BU (test model) of the above list. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Date: Oct. 23, 2020 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: EW780-1924-00 To whom it may concern:

We, the undersigned, hereby authorize SGS Hong Kong Limited and YW Yung in SGS Hong Kong Limited to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with VTech Telecommunications Ltd. This authorization is valid until further written notice from the applicant. Name (Printed):Michael Tsui Signature:

On behalf of Company: VTech Telecommunications Ltd. Telephone: 852-2680-5398 Name (Printed):Michael Tsui

Date: 2019-11-15 TO:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Title: Approbation Supervisor Regarding: FCC ID: EW780-1924-00 To whom it may concern:

We, the undersigned, hereby authorize SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch and Jing Song in SGS-CSTC Standards Technical Services Co., Ltd. (SGS) Shenzhen Branch to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, I acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with VTech Telecommunications Ltd. This authorization is valid until further written notice from the applicant. Print Name: Michael Tsui Signature:

On behalf of Company: VTech Telecommunications Ltd Telephone: 852-26805398 E-mail: michael_tsui@vtech.com

23/F Tai Ping Ind Center Block 1 57 Ting Kok Rd Tai Po NT Hong Kong To:

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: VTech Telecommunications Ltd Regarding: Confidentiality Request regarding application for FCC ID: EW780-1924-00 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 90 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 D01 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Michael Tsui Signature:

On behalf of Company: VTech Telecommunications Ltd Telephone: 852-26805398 E-mail: michael_tsui@vtech.com Title: Approbation Supervisor

VTech Telecommunications Ltd Nov. 14, 2019 To whom it may concern, Multiple Models Confirmation Letter I, the undersigned, hereby confirm that the family models are listed in the following table. These models are identical as follows:

Electronics/electrical designs, including software & firmware Construction design/Physical design/Enclosure PCB layout

(Others, please specify) The only differences between these models are the follows for marketing purpose:

Color Cosmetic details Trade name Model Number

(Others, please specify) Suffix (a, b,x) represents Color code Packing configuration Others, please specify) a= any alphanumeric character or blank is presenting number of baby unit. b = any alphanumeric character or blank is presenting color option For the product subject to authorization under FCC Declaration of Conformity:

In addition, it is to confirm that all the below information 1) the U.S. responsible party, 2) FCC label artworks and location, 3) FCC required statement in the user manual are the same but different in the following model numbers only:

Item No. Model Number New model Trade Name Remarks 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES YES RM5754 BU vtech Same as RM7754HD BU 1 Baby unit RM5754HD BU RM5754-2HD BU RM5754-aHD BU RM5854 BU RM5854HD BU RM5854-aHD BU VM813HD BU VM813-1bHD BU VM813-abHD BU RM7754 BU RM7754HD BU RM7754-2HD BU RM7754-aHD BU RM7854 BU RM7854HD BU Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 2 Baby units Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit, b color option Same as RM7754HD BU a Baby units, b color option Same as RM7754HD BU 1 Baby unit

1 Baby unit Same as RM7754HD BU 2 Baby units Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit VTech Telecommunications Ltd 17 18 19 20 21 YES YES YES YES YES RM7854-2HD BU RM7854-aHD BU VM816HD BU VM816-1bHD BU VM816-abHD BU Same as RM7754HD BU 2 Baby units Same as RM7754HD BU a Baby units Same as RM7754HD BU 1 Baby unit Same as RM7754HD BU 1 Baby unit, b color option Same as RM7754HD BU a Baby units, b color option The sample being submitted to SGS for conformity assessment is RM7754HD BU (test model) of the above list. Regards, Michael Tsui Approbation Supervisor