FCC ID: EW780-1496-00 Video Monitor - Baby Unit

The applied nameplate is located at the bottom of the baby units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above product. 2 meters. 4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parents or caregivers responsibility. This product could cease operating, and therefore you should not assume it will continue working properly for any given period of time. Further, this is not a medical device and should not be used as such. This product is intended to assist you in supervising your baby. 5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Power adapter information:

Output: 6V DC 400mA VTech Telecommunications Ltd. Model: VT05UUS06040 2.4V 400mAh Ni-MH Yiyang Corun Battery Co. Ltd Model: NI-MHAAA4002-FF GPI International Ltd. Model: VTRHC043C040 Rechargeable battery information:

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet. 9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible. 10. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 11. Unplug the power cords before replacing battery. 12. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 15. Do not overload wall outlets or use an extension cord. 16. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 17. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 18. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 19. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 20. You should test the sound reception every time you turn on the units or move one of the components. 21. Periodically examine all components for damage. 22. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 23. Children should be supervised to ensure that they do not play with the product. 24. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions 1. Use and store the product at a temperature between 32oF and 104oF. 2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. 3. Batteries should not be exposed to excessive heat such as bright sunshine or fire. 4. WarningStrangulation Hazard Children have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. 5. Never place the baby unit(s) inside the babys crib or playpen. Never cover the baby unit(s) or parent unit with anything such as a towel or a blanket. 6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic fields (EMF) This VTech product complies with all standards regarding electromagnetic fields (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientific evidence available today. 4 Whats in the box i o n l d r e n . f e e t D o n o t r a n g u l a t H a z a r d S t c h i r e a c h o f t h r e e o f t h i s c o r d o u t t l e a s t o b e a t i m e s . K e e p T h e c o r d n e e d s t l a l D o n o t l d a t t h e c h i t h a n e x t e n s i o n c o r d . r o m f a w a y u s e w i t a g . t h i s R i s q u e r e m o v e r a n g l e m e n t d t L e s . l o i g n e z c e c o r d o n d e s e n f a n t r o i s t a u m o i n s t e m p s . r o u v e r t o u t r e z p a s e n s e c e , c o r d o n d o i i r e t e t N e p i e d s d u n e n f a n t l o n g e . r a l i s e z p a s d e l i t e . N u t i q u e t t e t c e t t t R i e s g o d e r a n g u l a c i n l a a l c a n c e e s t f u e r a d e p o r t a r t e c a b l e t e c a b l e d e b e e s l a a l c a n c e M a n t e n g a e s l o u s e f u e r a d e E s l o s n i o s . N o r e s p i e s N o q u i t o d o m o m e n t o . d e i c a . t l o m e n o s i n a l m b r n i o e n c o n u n a e x t e n s i n d e l i q u e t a . t a e t e s t e Quick Start Guide 1 set for TM8112 2 sets for TM8112-2 i o n l d r e n . f e e t D o n o t r a n g u l a t H a z a r d S t c h i r e a c h o f t h r e e o f t h i s c o r d o u t t l e a s t o b e a t i m e s . K e e p T h e c o r d n e e d s t l a l D o n o t l d a t t h e c h i t h a n e x t e n s i o n c o r d . r o m f a w a y u s e w i t a g . t h i s R i s q u e r e m o v e r a n g l e m e n t d t L e s . l o i g n e z c e c o r d o n d e s e n f a n t r o i s t a u m o i n s t e m p s . r o u v e r t o u t r e z p a s e n s e c e , c o r d o n d o i i r e t e t N e p i e d s d u n e n f a n t l o n g e . r a l i s e z p a s d e l i t e . N u t i q u e t t e t c e t t t R i e s g o d e r a n g u l a c i n l a a l c a n c e e s t f u e r a d e p o r t a r t e c a b l e t e c a b l e d e b e e s l a a l c a n c e M a n t e n g a e s l o u s e f u e r a d e E s l o s n i o s . N o r e s p i e s N o q u i t o d o m o m e n t o . d e i c a . t l o m e n o s i n a l m b r n i o e n c o n u n a e x t e n s i n d e l i q u e t a . t a e t e s t e 1 Install parent unit battery Use only the battery supplied with this product. If the parent unit will not be used for a long time, disconnect and remove the battery to prevent possible leakage. NOTE NOTES 1 2 THIS SIDE UP TTERIES. AVERTISSEMENT :

THIS SIDE UP / CE CT VERS LE HAUT 3 4 Made in China / Fabriqu en chine CR0920 NE PAS INCINRER OU PERCER LES PILES. DO NOT BURN OR PUNCTURE BATTERIES. WARNING / AVERTISSEMENT :

BT183342/BT283342 (2.4V 400mAh Ni-MH) Battery Pack / Bloc-piles :

THIS SIDE UP / CE CT VERS LE HAUT TTERIES. AVERTISSEMENT :

THIS SIDE UP / CE CT VERS LE HAUT Go to www.vtechphones.com to register your product for enhanced warranty support and the latest VTech product news. Digital Audio Monitor with Glow-on-the-Ceiling Night Light TM8112 TM8112-2 Important safety instructions Users manual Congratulations on purchasing your new VTech product. Before using this product, please read Important safety instructions. This manual has all the feature operations and troubleshooting necessary to install and operate your new VTech product. Please review this manual thoroughly to ensure proper installation and operation of this innovative and feature-rich VTech product. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. CONFORMS TO UL STD. 62368-1 CERTIFIED TO CSA STD. C22.2 NO.62368-1 Specifications are subject to change without notice. 2021 VTech Communications, Inc. All rights reserved. 10/21. TM8112-X_QSG_V1 For more support information S m TM8112 TM8112-2 Connect the baby monitor Notes children. Use only the power adapters supplied with this product. Make sure the baby monitor is not connected to a switch-controlled electric outlet. Connect the power adapters in a vertical or floor mount position only. The adapters prongs are not designed to hold the weight of baby monitor, so do not connect them to any ceiling, under-

the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the baby unit and the power adapter cords are out of reach of to power on the baby unit. Press The power indicator LED light turns on. Press and hold off the baby unit. The power indicator LED light turns off. again to power to power on the Press and hold parent unit. The power indicator LED again light turns on. Press and hold to power off the parent unit. The power indicator LED light turns off. 2 Connect and charge the units 3 Power on the baby monitor 5 Positioning the baby monitor

> 3ft (1m) Caution Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the babys cot or playpen.

> 6.5ft (2m)

6.5ft (2m) Caution For hearing protection, make sure the parent unit is more than 6.5 ft (2 m) away from the baby unit. If you experience feedback:

Move the parent unit further until the noise stops. You can also press on the parent unit to lower or mute the noise. Place your baby unit at a location suitable for glow-on-the-ceiling night light to project images onto the ceiling. Charge the parent unit When you have installed the parent unit battery and connected it to power for the first time or after a power outage, the parent unit powers on automatically. Notes battery. The parent unit battery is fully charged after 16 hours of continuous charging. It takes longer to charge the battery when the parent unit is turned on. To shorten the charging time, turn the parent unit off while charging. The standby time varies depending on the volume level you set, your actual use and the age of 4 Status check You may test the baby monitor before initial use, and at regular times thereafter. 1. Make sure your baby unit and parent unit are on. 2. Speak towards the microphone of the baby unit. You will hear the sound at the parent unit, and see the visual sound indicators light up.

6.5ft (2m) Caution For hearing protection, make sure the parent unit is more than 6.5 ft (2 m) away from the baby unit. If you hear feedback, move the units further apart until the noise stops. You can also press lower or mute the noise. on the parent unit to Overview - Baby unit Overview - Parent unit Basic operation Speaker 6 Visual Sound Indicator Remotely on the parent unit:

1 Glow-on-the-ceiling night light 5 Power On/Off projector On/Off 2 Glow-on-the-Ceiling Night Light Press to turn Glow-on-the-Ceiling Night Light on or off. 6 Power jack 7 Speaker Press and hold to power on. Press and hold again to power off. 3 Microphone 4 Power LED light Light on when the baby unit is on. Light off when the baby unit is off. Need help?

TM8112 S m For the latest information and support, check out our website. Use your smartphone or mobile device to access online support by scanning the QR code on the right.

- OR -

Go to https://help.vtechphones.com/tm8112 or https://help.vtechphones.com/tm8112-2 You can also call our Customer Support at 1 (800) 595-9511 [in US]

or 1 (800) 267-7377 [in Canada] for help. 1 2 4 5 Battery LED light Light on when battery is charging. Light flashes when battery is low and needs charging. Light off when the parent unit is running on AC power without battery installed, or the parent unit is running on battery only. 3 Power LED light Light on when parent unit is Light off when the parent unit is powered on. powered off. Light flashes when there is no link between baby unit and parent unit. Power On/Off Press and hold to power on. Press and hold again to power off. 7 8 The visual sound indicator shows the sound level detected by the baby unit, and the volume level when setting unit volume. Green lights indicate a moderate sound level detected by the baby unit. Additional red lights indicate a higher sound level detected by the baby unit (e.g. baby crying loudly). Night Light LED light Light on when the projector is on. Light off when the projector is off. Glow-on-the-Ceiling Night Light On/Off Press to turn Glow-on-the-Ceiling Night Light on or off. TM8112-2

Adjust parent unit speaker volume. 9 Power jack 10 Belt clip 11 Battery compartment cover 10 11 Adjust speaker volume The parent unit speaker volume is preset to Level 3 by default, you can adjust it to your preferred volume level. Press to decrease the volume, and to increase the volume. To mute the speaker volume:

Press repeatedly until the volume reaches the minimum. NOTENote NOTES If you continue to press or when the volume reaches the minimum or maximum setting, the parent unit will beep twice. Turn on and off glow-on-the-ceiling night light Directly on the baby unit:

Press to turn the night light on, and press again to turn it off. Press Press to turn the night light on, the again to turn the night light off, the Night Light LED light will light up. Night Light LED light will switch off. Parent unit alert tones Low battery tone Beeps twice every 10 minutes when the battery is low. Out of range tone Beeps three times every 30 seconds when there is no link between the baby unit and parent unit, or when the parent unit is out of range from the baby unit. General product care or fluorescent lamps). To keep this product working well and looking good, follow these guidelines:

Avoid putting it near heating appliances and devices that generate electrical noise (for example, motors DO NOT expose it to direct sunlight or moisture. Avoid dropping the product or treating it roughly. Clean with a soft cloth. DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap. DO NOT use cleaning spray or liquid cleaners. Make sure the baby unit and parent unit are dry before you connect them to the mains again. Limited warranty What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period

(Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will replace at VTechs option, without charge, a Materially Defective Product. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the replacement Products to you in working condition. You should expect the replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase (90 days on products purchased as Refurbished*). This limited warranty also applies to the replacement Product for a period of either (a) 90 days from the date the replacement Product is shipped to you or (b) the time remaining on the original one-year warranty (90-day limited warranty on products that are purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store carry a 90-day replacement warranty. What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, fire, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modification by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difficulty; and 2. Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modifications to this limited warranty and you should not rely on any such modification. State/

Provincial Law Rights: This warranty gives you specific legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of fitness for a particular purpose and merchantability (an unwritten warranty that the Product is fit for ordinary use) are limited to one year from the date of purchase. Some states/provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost profits or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase. California Energy Commission battery charging testing mode This baby monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your baby monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to baby units, the CEC battery charging testing mode is activated while it is powered off and charging. Disclaimer and Limitation of Liability VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss resulting from the use of this users manual. VTech Communications, Inc. and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of this product. Company: VTech Communications, Inc. Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada For cETL compliance only Mesures de scurit importantes La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base afin de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. Linstallation par un adulte est requise. 2. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit ne remplace pas la surveillance adulte du nourrisson. La supervision du nourrisson est la responsabilit du parent ou de la personne qui soccupe de lenfant. Ce produit pourrait cesser de fonctionner et, par consquent, vous ne devriez pas prsumer quil continuera de fonctionner correctement pendant une priode de temps donne. De plus, il ne sagit pas dun instrument mdical et ne devrait pas tre utilis comme tel. Ce produit est destin vous aider superviser votre bb. 5. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 6. MISE EN GARDE: Utilisez uniquement les piles fournies. Il existe un risque dexplosion si un autre type de batterie est utilis pour lunit Parents. Nincinrez pas les piles. Celles-ci risqueraient dexploser. Jetez les piles uses selon les renseignements suivant le sceau du RBRC. 7. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. Informations sur les adaptateurs lectriques :

Sortie : 6V CC 400mA VTECH TELECOMMUNICATIONS LTD. Modle : VT05UUS06040 Informations sur les piles rechargeables :

2xAAA 2.4V 400mAh Ni-MH YIYANG CORUN BATTERY CO LTD. Modle : NI-MHAAA4002-FF GPI INTERNATIONAL LTD. Modle : VTRHC043C040 Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. Pour les PRODUITS BRANCHER UNE PRISE DE COURANT, la prise de courant doit tre installe prs du produit, afin dassurer une accessibilit scuritaire la prise de courant. 8. 9. 10. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 11. Dbranchez les cordons dalimentation avant de remplacer le bloc-piles. 12. Ne coupez pas les cordons dalimentation pour remplacer les fiches, car ceci peut prsenter un danger potentiel. 13. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 14. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 15. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. 16. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 17. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 18. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-

circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 19. Afin de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 20. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 22. 21. Examinez les composantes afin de vrifier si celles-ci ne sont pas endommages. Il existe un trs faible risque de perte de confidentialit avec certains appareils lectroniques (autres coute-bbs, tlphones sans fils etc.). Pour lviter, sassurer que le produit na jamais t utilis avant lachat, rinitialiser lunit de faon priodique, teindre lcoute-bb quand il nest pas en cours dutilisation. 23. Les enfants devraient tre superviss afin de vous assurer quils ne jouent pas avec lappareil. 24. Le produit nest pas conu pour tre utilis par des personnes

(incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn suffisamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde 1. Utilisez et entreposez le produit une temprature entre 0C

(32F) et 40C (104 F). 2. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Le bloc-piles ne doit pas tre expos la chaleur excessive telle que la lumire du soleil ou au feu. Assurez-vous que le moniteur et le cordon de ladaptateur sont toujours hors de porte des enfants, au moins 1 mtre (3 pieds) de lenfant ou du berceau, pour viter tout risque de strangulation. 5. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. 6. Dautres quipements lectroniques peuvent produire des interfrences sur votre moniteur vido et audio. Tentez dinstaller votre moniteur vido ou audio lcart des appareils lectroniques tels que des routeurs sans fil, radios, tlphones cellulaires, interphones, moniteurs, tlphones, ordinateurs personnels, lectromnagers et tlphones sans fil. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans fil) :

Lorganisme Wireless Technology Research, LLC (WTR), une firme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans fil portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la firme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans fil au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans fil directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identifi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans fil proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientifiques dont nous disposons aujourdhui. 3. 4. FCC and IC regulations FCC Part 15 This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the The RBRC seal amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. Caution: The baby unit must be installed to provide a separation distance of at least 20cm from all persons. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specifications. FCC RF radiation exposure statement Caution: This baby unit must be installed to provide a separation distance of at least 20cm from all persons. For body worn operation, this parent unit has been tested and meets the FCC RF exposure guidelines. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. The RBRC seal on the Ni-MH battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used Ni-MH batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation makes it easy for you to drop off the spent product at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Ni-MH battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY are registered trademarks of Call2recycle, Inc. Technical specifications Frequency control Crystal controlled PLL synthesizer Transmit frequency Channels 5 Baby unit: 1921.536 - 1928.448 MHz Parent unit: 1921.536 - 1928.448 MHz Nominal effective range Maximum power allowed by FCC and IC. Actual operating range may vary according to environmental conditions at the time of use. Power requirements Baby unit adapter: Input: 100-120V AC 60Hz; Output: 6V DC @ 400mA Parent unit adapter: Input: 100-120V AC 60Hz; Output: 6V DC @ 400mA Parent unit battery: 2.4V 400mAh Ni-MH battery

Model: TM8112 PU SN:XXXXXXXXXXX IC: 1135B-80149600 HVIN: 35-201822PU FCC ID: EW780-149600 PU:Label: 28x10 mm

(80-1496-00-05) IC: 1135B-80149601 HVIN: 35-201823BU FCC ID: EW780-149601 A/V I.C.T.E. VTech Customer Service1-800-595-9511 www.vtechphones.com MANUFACTURED IN CHINA Model: TM8112 BU S/N: XXXXXXXXXXX BU:Label: 35.6x24.6 mm

(80-1496-00-05)

VTech Telecommunications Ltd Nov 12, 2021 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 15 Certification FCC ID: EW780-1496-00 Request is hereby submitted by VTech Telecommunications Ltd. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and VTech Telecommunications Ltd. reserves the right to discern which parties can obtain access to these information:

Schematics Detailed Block diagrams Detailed Operational/Functional Description The rationale for request for confidentiality is as followings:

This information represents intellectual property of VTech Telecommunications Ltd. and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards, Michael Tsui Approbation Supervisor

Appendix B1 Letter of Agency for FCC Certification Nov 15, 2021 To whom it may concern, Letter of Agency I, an officer of VTech Telecommunications Limited do hereby authorize Intertek Testing Services (Ms Jess Tang) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in 1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Michael Tsui Approbation Supervisor