FCC ID: EW780-2517-00 Video Monitor - Baby Unit

 

Connect, charge and power on the baby monitor

2. Charge the Parent Viewer battery before use

3. Power On or Off the Baby Monitor

1. Slide the On/Off switch to ON in order

to power on your Baby Unit.

2. After the Parent Viewer is fully charged,

until the welcome screen

press and hold

appears.

4. Positioning the Baby Monitor

1.

> 3ft (1m)

4.

70

25.5°C

> 3ft (1m)

Important Safety Instructions

The applied nameplate is located at the bottom of the Baby Unit’s base.

When using your equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock

and injury, including the following:

1. Follow all warnings and instructions marked on the product.

2. Adult setup is required.

3. CAUTION: Do not install the Baby Unit at a height above 2 meters.

4. This product is not a substitute for adult supervision of the infant. Supervising the infant is the parent’s or caregiver’s

responsibility. This product could cease operating, and therefore you should not assume it will continue working

properly for any given period of time. Further, this is not a medical device and should not be used as such. This product

is intended to assist you in supervising your baby.

5. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub

or swimming pool, or in a wet basement or shower.

6. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the

Parent Viewer. The battery cannot be subjected to high or low extreme temperature and low air pressure at high

altitude during use, storage or transportation. Disposal of battery into fire or a hot oven, or mechanically crushing or

cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding

environment can result in an explosion or the leakage of flammable liquid of gas. Battery subjected to extremely low

air pressure may result in an explosion or the leakage of flammable liquid or gas. Dispose of used battery according to

the information in The RBRC seal.

7. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the

product.

Power adapter information:

Baby Unit output: Output: 5V DC 1A; VTech Telecommunications Ltd.; Model: VT05EUS05100

Parent Viewer output: Output: 5V DC 2A; VTech Telecommunications Ltd.; Model: VT07EUS05200

Rechargeable battery information:

Zhuhai Great Power Energy Co., Ltd.; Lithium battery, 3.7V 5000mAh; Model: GSP806090-5Ah-3.7V-1S1P

1. Connect the Baby Monitor

Notes:

• The rechargeable battery in the Parent Viewer is built-in.

• Use only the power adapters supplied with this product.

• Make sure the Parent Viewer and the Baby Unit are not connected to the switch controlled electric outlets.

• Connect the power adapters in a vertical or floor mount position only. The adapters’ prongs are not designed to hold

the weight of the Parent Viewer and the Baby Unit, so do not connect them to any ceiling, under-the-table, or cabinet

outlets. Otherwise, the adapters may not properly connect to the outlets.

• Make sure the Parent Viewer, the Baby Unit and the power adapter cords are out of reach of children.

• To maintain compliance with the FCC’s RF exposure guidelines, place the Baby Unit at least 20cm from nearby persons.

8. The power adapters are intended to be correctly oriented in a vertical or floor mount position. The prongs are not

designed to hold the plug in place if it is plugged into a ceiling, under-the-table or cabinet outlet.

9. For pluggable equipment, the socket-outlet shall be installed near the equipment and shall be easily accessible.

10. Unplug this product from the wall outlet before cleaning.

11. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. Do not cut off the power adapters to replace

them with other plugs, as this causes a hazardous situation.

12. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or

crimped.

capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning

use of the appliance by a person responsible for their safety.

What’s Included

Cautions

1. Use and store the product at a temperature between 32oF and 104oF.

2. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source.

3. Batteries should not be exposed to excessive heat such as bright sunshine or fire.

SAVE THESE INSTRUCTIONS

13. This product should be operated only from the type of power source indicated on the marking label. If you are not

4.

Warning—Strangulation Hazard—Children have STRANGLED in cords. Keep this cord out of the

sure of the type of power supply in your home, consult your dealer or local power company.

reach of children (more than 3 ft (0.9m) away). Do not remove this tag.

14. Do not overload wall outlets or use an extension cord.

15. Do not place this product on an unstable table, shelf, stand or other unstable surfaces.

16. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the

back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must

not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be

placed near or over a radiator or heat register.

17. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points

or create a short circuit. Never spill liquid of any kind on the product.

18. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility.

Opening or removing parts of the product other than specified access doors may expose you to dangerous voltages

or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used.

19. You should test the sound reception every time you turn on the units or move one of the components.

20. Periodically examine all components for damage.

21. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless

telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby

monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not

use it for some time.

22. Children should be supervised to ensure that they do not play with the product.

23. The product is not intended for use by persons (including children) with reduced physical, sensory or mental

5. Never place the Baby Unit(s) inside the baby’s crib or playpen. Never cover the Baby Unit(s) or Parent

Viewer with anything such as a towel or a blanket.

6. Other electronic products may cause interference with your baby monitor. Try installing your baby monitor as far away

from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors,

televisions, personal computers, kitchen appliances and cordless telephones.

Precautions for users of implanted cardiac pacemakers

Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the

interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug

Administration, WTR recommends to physicians that:

Pacemaker patients

• Should keep wireless devices at least six inches from the pacemaker.

• Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON.

WTR’s evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices.

Electromagnetic fields (EMF)

This LeapFrog product complies with all standards regarding electromagnetic fields (EMF). If handled properly and

according to the instructions in this user’s manual, the product is safe to be used based on scientific evidence available

today.

Parent Guide

x 2

x 2

1 set for LF815HD

2 sets for LF815-2HD

Requirements

For mobile access:

LeapFrog mobile app

Network

Wi-Fi router

Wi-Fi

2.4GHz 802.11 b/g/n

Internet connection

1.5 Mbps @ 720p or 2.5 Mbps @1080p upload bandwidth per Baby Unit

When you connect and turn on the Parent Viewer, the battery charges automatically.

Notes:

• Before using the baby monitor for the first time, charge the Parent Viewer battery for 12 hours.

When the Parent Viewer battery is fully charged, the battery icon becomes solid

.

• The standby time varies depending on the Baby Unit sensitivity levels you set for Auto Wake-Up,

your actual usage time and the age of the battery.

The battery icon on the screen indicates the battery status (see the following table).

Battery Indicators

Battery Status

Action

The screen displays

light flashes.

The

.

The battery icon becomes

solid

.

The battery has very little

power left and may only be

used for a short time.

The battery is fully charged.

Charge without interruption

(about 30 minutes).

To keep the battery charged,

connect it to AC power when

not in use.

How the system works?

Direct mode

The Parent Viewer and the Baby Unit of your video monitor connect to each other in Direct mode by

default, which allows you to stream live video right out of the box. Direct mode connection lets you

stream live video from the Parent Viewer only.

2.

Press and hold

3.

3. Status Check

Once your Baby Unit and Parent Viewer are

powered on, your Parent Viewer displays image

from the Baby Unit, and the

LINK LED light

turns on. The Baby Unit’s POWER LED light also

turns on.

70

25.5°C

>

3ft (1m)

< 3ft (1m)

70

25.5°C

Note:

• The POWER LED Light is OFF by default.

Parent Viewer Icons

Main Menu Icons

Monitoring mode (For LF815-2HD only)

Detection

Sound

Humidity and Temperature

Sensor

Lullabies and

Soothing Sounds

is

in with

real-time

Rest assured of the environment

the

your baby

built-in

temperature

and humidity sensor. It lets you

know when the room is outside

a comfortable temperature and

humidity range. For more details,

see Parent Viewer Icons section.

Comforting and engaging your

baby can be done easily and

from a distance. Choose from 5

lullabies and 5 soothing sounds to

help lull your baby back to sleep.

For more details, see Parent

Viewer Icons - lullaby section.

Motion and Sound Sensor

With adjustable alerts on noise

or motion detected from the baby

monitor, give yourself a peace of

mind with an extra set of eyes. For

more details, see Parent Viewer

Icons - Detection section.

Key Features

Color and B&W

Automatic Night Vision

Thanks to the

latest starlight

sensor and noise suppression

technology, you can check in on

your baby 24/7 with the finest

clarity. Night vision is no longer

just black-and-white, you can

choose to see your baby in color at

night! For more details, see Night

Vision (B&W and Color) section.

Night Light

Need some additional

lighting

near your baby for those bedtime

stories? The built-in night light on

the baby monitor can help with

that. You can control the night

light directly on the Baby Unit, or

remotely from the Parent Viewer.

For more details, see Parent

Viewer Icons - Night Light section.

Technical Specifications

Frequency

Channels

LCD

2412-2462 MHz

1-11

5” Color LCD

(IPS 1280x720 pixels)

Nominal effective range

Maximum power allowed by FCC and IC. Actual operating range may vary according to

environmental conditions at the time of use.

4

Power requirements

Parent Viewer: 3.7V 5000mAh Lithium-ion battery

Baby Unit power adapter: Output: 5V DC @ 1A

Parent Viewer power adapter: Output: 5V DC @ 2A

Credits:

The Background Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.

The Stream Noise sound file was created by Caroline Ford, and is used under the Creative Commons license.

The Crickets At Night sound file was created by Mike Koenig, and is used under the Creative Commons license.

The Heart Beat sound file was created by Zarabadeu, and is used under the Creative Commons license.

Overview - Parent Viewer

1

2

3

4

5

6

7

8

9

10

11

12

13

14

1

2

3

4

Link LED light

• On when the Parent Viewer

is linked to the Baby Unit.

• Flashes when the link to the

Baby Unit is lost.

Battery LED light

3-level sound indicator light

Night Mode quick set key

• Select black-and-white or

color night vision viewing

mode.

• Adjust night light

brightness.

5

6

7

9

Arrow Keys

Menu / Select

Zoom

10

11

Power /

LCD Off

Talk /

Return

• Press and hold to talk to the

12 Antenna

13 Power jack

• While in a sub-menu, press

14 RESET

Baby Unit.

to exit.

• Force reboot the

Parent Viewer.

15 Stand

8 Microphone

Volume

• Press to view the volume

adjustment bar.

Overview - Baby Unit

9

9

6

9

6

6

6

1

2

3

4

5

1

2

3

5

1

2

3

1

2

3

4

4

5

5

CONFORMS TO

UL STD.

62368-1

CERTIFIED TO

CSA STD.

C22.2 NO.62368-1

7

8

7

8

7

8

7

8

1

2

3

4

5

6

7

8

Light sensor

Camera

Microphone

Infrared LEDs

Night light

Speaker

POWER LED Light

On / Off switch

9

10

12

12

13

13

12

13

12

13

10

11

10

11

9

10

11

11

Night light control key

• Press to turn the night light on or off.

• Tap and hold to adjust the degree of brightness

alternately; release when it reaches your

desired brightness level.

10

11

Antenna

Power jack

12 Wall mount holes

13

PAIR key

• The Parent Viewer and Baby Unit(s) provided

are already paired.

15

70

25.5°C

Local access

Tip:

• You may experience reduced signal strength if your Parent Viewer and Baby Unit are far apart, or there are

obstructing factors, such as internal walls, between them. Move the Parent Viewer closer to the Baby Unit to

improve the signal strength. You can also set up Router mode to connect the units via your home Wi-Fi network

to improve the connection between your Parent Viewer and Baby Unit.

Night light

Wi-Fi Router mode

You can continue using your video monitor

with Direct mode connection, or you can set

up your monitor in Router mode connection.

Router mode uses your home Wi-Fi network

to connect your video monitor. It supports live

video streaming through the Parent Viewer

and smartphone app.

We recommend that you set up your monitor

in Router mode to enjoy live video streaming

via your Parent Viewer with an enhanced

connection.

70

25.5°C

Lullaby

If you want to stream live video remotely with

your mobile device, download and install the

LeapFrog mobile app. With the mobile app,

your Wi-Fi router (not included) provides

Internet connectivity to your HD video monitor system. It serves as a communicating channel

between your Baby Unit and mobile device, allowing you to monitor and/or control your Baby Unit

wherever you are. For more details, see Download app for mobile access section in this Parent Guide.

Enhanced local access

Mobile access

Notes:

• Your Parent Viewer detects the connection signal strength. If you have connected your video monitor with your

home Wi-Fi network, your Parent Viewer automatically switches to direct or router mode - whichever has a

stronger signal strength.

• When both Parent Viewer and app are viewing the camera simultaneously, the video quality will be optimised

to deliver the best possible viewing result.

1

2

1 2

• Baby Unit 1 in Single mode

• Baby Unit 2 in Single mode

• Patrol mode

Viewer displays video feeds from all

paired Baby Units at the same time

in split view.

• Split mode

Viewer displays a single Baby Unit’s

video feed that transitions to a

different Baby Unit every 10 seconds.

• Turn On/Off night light.

• Select a night light Color.

Choose from 7 preset colors

and 3 light patterns.

• Select Auto Brightness mode (or)

• Adjust the fixed level night light

brightness.

• Set a Timer to turn the night

light off after 15, 30, or 60

minutes.

• Stop melody playing.

• Play all melodies.

• Play and view all Songs.

Choose from 5 melodies and

5 soothing sounds.

• Set a timer to stop playing

melodies after 15, 30, or 60

minutes, or let them play

non-stop.

Tip: Do you icons look a little different? Your baby monitor

probably got a recent software update. Go to our online manual for

an overview of the latest icons (See Online Help).

Baby Unit settings

General settings

• Select sound Sensitivity level.

• Turn on/off Sound Detection Alert.

Parent Viewer beeps when the Baby Unit

detects sounds above the chosen sound

sensitivity level.

• Turn on/off Auto Wake Up function.

Once the Baby Unit detects sounds

that are louder than the chosen sound

sensitivity level, the Parent Viewer screen

and speaker turn on automatically.

Motion

• Turn on/off Motion Alert.

Parent Viewer beeps when the Baby

Unit detects movements larger than the

chosen motion sensitivity level.

• Select motion Sensitivity level.

Temperature

• Turn on/off Temperature Alert.

Status Bar Icons

When you turn it on, the Parent Viewer

beeps whenever the room temperature

detected by the Baby Unit falls outside the

set temperature range.

or

Parent Viewer settings

• Select the Minimum temperature of the

temperature alert range.

• Select Maximum temperature of the

temperature alert range.

• Select temperature Format.

Change the temperature display format to

Fahrenheit (oF) or Celsius (oC ).

• Adjust Parent Viewer screen Brightness.

• Adjust Low Battery Alert Tone Volume.

• Adjust No Link Alert Tone Volume.

• Turn on/off Dim Mode.

(See Dim Mode section to learn more)

• Change the Language on your Parent Viewer

70

25.5°C

< 3ft (1m)

Note:

• To avoid interference from other electronic

devices, place your baby monitor at least 3

feet (1 meter) away from devices such as

wireless routers, microwaves, cell phones

and computers.

Caution:

• The default volume of your Parent Viewer

is level 3, and the maximum volume is

level 5. If you experience a high-pitched

screeching noise from your baby monitor

while positioning:

- Make sure your Baby Unit and Parent Viewer

are more than 3 feet (1 meter) apart, OR

- Lower the volume of your Parent Viewer.

• Turn on/off Status LED indicator.

When on, the POWER LED light on the

Baby Unit turns on/off or flash to indicate

the camera’s conditions.

• Adjust the Baby Unit’s speaker Volume.

• Configure Wi-Fi.

Change your Wi-Fi network, select a

Connection Mode, and check the Baby Unit

and Parent Viewer’s Connection Status.

• Connect Mobile Phone

• Add Baby Unit

• Remove Baby Unit

• Reset Settings to default.

• Software Update

Check if your Parent Viewer software is up to

date, or install a new update when available.

Current view status

• The Baby Unit number that is being viewed when in:

- Single Baby Unit mode

- Patrol mode

(* For LF815-2HD or pairing with LF815-0HD)

- Split mode

(* For LF815-2HD or pairing with LF815-0HD)

Split mode (* For LF815-2HD or pairing with LF815-0HD)

Patrol mode (* For LF815-2HD or pairing with LF815-0HD)

Black and white night vision is activated.

Color night vision is activated.

Motion detection and alert is turned on.

Sound detection and alert is turned on.

Melodies or soothing sounds are playing.

Night light is turned on and the automatic

brightness setting is turned off.

Touch and learn!Touch and learn!Read our complete warranty policy online at leapfrog.com/warranty.Visit our website leapfrog.com leapfrog.com for more information about products, downloads, resources and more.LeapFrog Enterprises, Inc.,a subsidiary of VTech Holdings Limited.TM and © 2021 LeapFrog Enterprises, Inc.All right reserved.Scan the QR code to enter our Knowledge Base:Or go to www.leapfrog.zendesk.comLF815HDLF815-2HD LF815-0HD5” WiFi 5” WiFi High DefinitionHigh Definition Video MonitorVideo MonitorNeed help?Visit leapfrog.com/support Parent GuideThis guide contains important information.Please keep it for future reference.Parent Viewer Icons (continued)

Night light is turned on and the automatic

brightness setting is turned on.

Alert Icons

5050

Parent Viewer speaker is muted.

Temperature alert is turned on.

Humidity is lower than 30%.

Humidity is within 30-60%.

Humidity is higher than 60%.

70 FF ˚˚FF Temperature is lower than 68°F.

˚˚FF Temperature is between 68-75°F.

˚˚FF Temperature is higher than 75°F.

Battery level indicator

• Displays when the Parent

Viewer’s battery is low

and needs charging.

• Displays when motion is

detected by a Baby Unit.

• Displays when sound is

detected by a Baby Unit.

• Displays when the

temperature detected by

the Baby Unit exceeds the

set maximum.

• Displays when the

temperature detected

by the Baby Unit is lower

than the set minimum.

Night Vision (B&W and Color)

When the Baby Unit being viewed detects

low light levels, the infrared LEDs switch on

automatically with the activiation of the B&W

Night Vision mode. Baby Unit has infrared LEDs

that allow you to see your baby clearly at night

or in a dark room.

When Black and White Night Vision mode is

activated,

appears on the screen. When

Color Night Vision mode is activated,

appears on the screen.

Notes:

• It is normal to see a short white glare on your Parent

Viewer screen as the Baby Unit is adapting to the

dark environment.

• If you adjust the night vision mode while night vision

is not activated, the new settings will be saved and

applied the next time it activates.

Tip:

• The video quality may vary depending on the

surrounding environment and interfering factors like

lightings, objects, colors and backgrounds. Adjust the

Baby Unit’s angle or place the Baby Unit at a higher

elevation to prevent glare and blurry displays.

Night Vision

Mode

Description

B&W Night Vision

Suitable for extremely dark or low

light environments.

Images will be in black-and-white.

Color Night Vision

Suitable for low-light room

conditions with night light as an

assisting light source.

Images will be in color.

Change your night vision viewing mode

1. Press the Night Mode quick set key

to view the Night Mode menu.

or

2. Press

to choose

black-and-white night vision viewing or

for color night vision viewing.

for

Basic Operation - Parent Viewer

to open the volume adjustment

Adjust Parent Viewer’s speaker volume

1. Press

bar.

2. Press

and

to decrease the speaker volume.

to increase the speaker volume

Turn on/off the Parent Viewer screen

You can turn on or off the Parent Viewer

screen without powering off the Parent Viewer.

You will still be able to hear sounds from the

Baby Unit.

• Press

on the Parent Viewer to turn off

the screen.

• Press any key on the Parent Viewer to turn

on the screen again.

Talk to your baby via the Baby Unit

1. Press and hold the

key.

2. When the

icon displays on the screen,

speak to your Parent Viewer. Your voice is

transmitted to the Baby Unit.

3. When finished talking, release the

key

and hear your baby again.

to enter the menu, choose a menu

Use the menu

Press

item, or save a setting. You can use the Parent

Viewer for advanced settings or operations,

such as to play or stop the Baby Unit’s lullaby,

or to adjust the Baby Unit sound sensitivity.

, or

to scroll among the

While in the menu:

• Press

,

menu options.

,

setting.

Press and hold

• Press

to select an item, or to save a

Zoom

Press

sequence is 1x

to zoom in or out. The zoom

, 4x

, then 8x

, 2x

.

• Press

/

to return to the live video.

• Press

to go to the Help & Info page.

70

25.5°C

70

25.5°C

70

25.5°C

Mount the Baby Unit on a dry wall (optional)

Notes:

• Check for reception strength and the Baby Unit’s viewing angle before drilling the holes.

• The types of screws and anchors you need depend on the composition of the wall. You may need to purchase the

screws and anchors separately to mount your Baby Units.

Protect your privacy and online security

LeapFrog cares about your privacy and peace of mind. That’s why we’ve put together a list of industry-

recommended best practices to help keep your wireless connection private and your devices protected

when online. We recommend you carefully review and consider complying with the following tips.

Ensure your wireless connection is secure.

• Before installing a device, ensure your router’s wireless signal is encrypted by selecting the

2. If you drill the holes into a stud, go

“WPA2-PSK with AES” setting in your router’s wireless security menu.

to step 3.

•

If you drill the holes into an object

other than a stud, insert the wall

anchors into the holes. Tap gently

on the ends with a hammer until

the wall anchors are flush with the

wall.

3. Insert the screws into

the holes and tighten

the screws until only 1/4

inch of the screws are

exposed.

OR

4. Place the Baby Unit on

the wall mount bracket.

Tighten the screw into

the threaded socket at

the bottom to secure

the Baby Unit. Align

the holes on the wall

mount bracket with the

screws on the wall, and

slide the wall mount

bracket down until it

locks into place.

1

2

1. Place the wall mount bracket

on a wall and then use a

pencil to mark the top and

the bottom holes as shown.

Remove the wall mount

bracket and drill two holes in

the wall (7/32 inch drill bit).

3. Align the wall mount

bracket and screws with

the holes in the wall as

shown. Tighten the screw

in the middle hole first,

so that the wall mount

bracket position is fixed.

You can tighten the other

screw in the top hole.

4. Place the Baby Unit on

the wall mount bracket.

Tighten the screw into

the threaded socket at

the bottom to secure the

Baby Unit.

5. You can maximize your Baby Unit’s

viewing angles by tilting the wall mount

bracket.

Hold the Baby Unit, and then rotate

the knob in an anti-clockwise direction.

This will loosen the joint of the wall

mount bracket.

Tilt your Baby Unit up or down to adjust

to your preferred angle. Then, rotate

the knob in a clockwise direction to

tighten the joint and secure the angle.

Change default settings.

• Change your wireless router’s default wireless network name (SSID) to something unique.

• Change default passwords to unique, strong passwords. A strong password:

- Is at least 10 characters long.

- Is complex.

- Does not contain dictionary words or personal information.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers.

Keep your devices up to date.

• Download security patches from manufacturers as soon as they become available. This will ensure

you always have the latest security updates.

If the feature is available, enable automatic updates for future releases.

•

Disable Universal Plug and Play (UPnP) on your router.

• UPnP enabled on a router can limit the effectiveness of your firewall by allowing other network

devices to open inbound ports without any intervention or approval from you. A virus or other

malware program could use this function to compromise security for the entire network.

For more information on wireless connections and protecting your data, please review the following

resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips –

www.fcc.gov/consumers/guides/how-protect-yourself-online.

2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet –

www.us-cert.gov/ncas/tips/ST15-003.

3. Federal Trade Commission: Using IP Cameras Safely –

https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely.

4. Wi-Fi Alliance: Discover Wi-Fi Security –

http://www.wi-fi.org/discover-wi-fi/security.

Instructions for Care

FOR INDOOR, DRY-LOCATION USE ONLY.

To keep this product in good condition, follow these guidelines:

•

•

•

Avoid putting it near heating appliances and devices

that generate electrical noise (for example, motors or

fluorescent lamps).

Do not spill liquid of any kind on this product or

immerse the product in water as it may render it

inoperative.

Clean with a slightly damp cloth in cold water (do not

use soap, detergent, or other chemicals).

Keep food and beverages away from this product.

• Make sure the product is dry before you connect it to

the power source again.

Never try to dismantle the unit.

Avoid prolonged exposure to extreme temperatures

and direct sunlight or moisture.

Avoid dropping the product or treating it roughly.

•

•

•

•

Night Light

Want a softer hue from the Baby Unit’s night light to relax your little one? You can control the brightness

of its glow remotely from your Parent Viewer, or directly on the Baby Unit.

Dim Mode

Adjust the night light on the Parent Viewer

Adjust the night light on the Baby Unit

The Parent Viewer display will dim to conserve energy after 5 minutes of inactivity, in which

there were neither any key pressed nor alert received from the Baby Unit.

•

•

Tap the Night light control key

located

on the top of the Baby Unit to turn on/off the

night light.

Tap and hold the Night light control key

to adjust the night light’s brightness. It

changes level by level at a time.There are 5

levels in total.

5 minutes of inactivity

70

25.5°C

Press any button

1. Press the Night Mode quick set key

to view the Night Mode menu.

2. Press

the night light when it is switched off).

to brighten the night light (or turn on

Press

to dim the night light (or turn off the

night light when it is at the lowest brightness

level).

- OR -

1. Press

to enter the main menu.

2. Press

again to select

.

3. Press

and

to select

, press

.

4. Press

and

to choose the desired

brightness level, then press

your selection.

to confirm

Test the location for the Baby Unit

If you plan to install your Baby Unit in a designated location,

and use your home Wi-Fi network to connect your video

monitor, you need to test which of your selected monitoring

areas within the house have good Wi-Fi signal strength.

After you have powered on your Parent Viewer, you can

check the Parent Viewer’s Wi-Fi signal strength by going to:

> Configure Wifi > Connection Status.

Adjust the distance between your Baby Unit and the Wi-Fi

router if needed. Once you have identified the suitable

location, you can install your Baby Unit.

Note:

• If Auto Brightness has been pre-selected, any adjustment in night light brightness (either on the Baby Unit or

the Parent Viewer) will automatically turn off Auto Brightness mode and switch to the fixed level of brightness.

Select Baby Unit 1

view the image from the selected Baby Unit.

or Baby Unit 2

to

For LF815-2HD and Pairing with LF815-0HD Only

Single CAM mode

70

25.5°C

Monitoring mode

1

2

Patrol mode

70

25.5°C

70

25.5°C

70

25.5°C

Select Patrol mode as your monitoring

mode to alternately view the image from

Baby Units

and

seconds.

every 10

70

25.5°C

10s

70

25.5°C

70

25.5°C

1 2

Split mode

Select Split mode as your monitoring mode to view the images from

both Baby Units at the same time.

Note:

• While in Split mode, you can press

or Baby Unit 2

Baby Unit 1

highlighted Baby Unit.

or

to highlight the view of the

, and hear the sounds transmitted from the

Disclaimer and Limitation of Liability

LeapFrog and its suppliers assume no responsibility for any damage or loss resulting from the use of this handbook.

LeapFrog and its suppliers assume no responsibility for any loss or claims by third parties that may arise through the use of

this software. LeapFrog and its suppliers assume no responsibility for any damage or loss caused by deletion of data as a

result of malfunction, dead battery, or repairs. Be sure to make backup copies of important data on other media to protect

against data loss.

THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO

CONDITIONS: (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT

ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

CAN ICES-3 (B)/NMB-3(B)

Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s

authority to operate the equipment.

Warranty: Please visit our website at leapfrog.com for full details of the warranty provided in your country.

The RBRC seal

The RBRC seal on the Li-ion battery indicates that VTech Communications, Inc. is voluntarily participating

in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out

of service within the United States and Canada. The program provides a convenient alternative to placing

used Li-ion batteries into the trash or municipal waste, which may be illegal in your area.

VTech’s participation makes it easy for you to drop off the spent battery at local retailers participating in the

program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY® for information

on Li-ion battery recycling and disposal bans/restrictions in your area. VTech’s involvement in this program is part of its

commitment to protecting our environment and conserving natural resources.

The RBRC Seal and 1 (800) 8 BATTERY® are registered trademarks of Call2recycle, Inc.

FCC and IC regulations

FCC Part 15

This equipment has been tested and found to comply with

the requirements for a Class B digital device under Part 15 of

the Federal Communications Commission (FCC) rules. These

requirements are intended to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with

the instructions, may cause harmful interference to radio

communications. However, there

is no guarantee that

interference will not occur in a particular installation. If

this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and

• Connect the equipment into an outlet on a circuit different

from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician

receiver.

for help.

WARNING: Changes or modifications to this equipment not

expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC rules. Operation

is subject to the following two conditions: (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

To ensure safety of users, the FCC has established criteria for the

amount of radio frequency energy that can be safely absorbed

by a user or bystander according to the intended usage of the

product. This product has been tested and found to comply

with the FCC criteria. The Baby Unit shall be installed and used

such that parts of all persons’ body are maintained at a distance

of approximately 8 in (20 cm) or more. The transmitter and

antenna of the Parent Viewer shall be held at least 1 in (2.5 cm)

from your face.

This Class B digital apparatus complies with Canadian

requirement: CAN ICES-3 (B)/NMB-3(B)

device

contains

licence-exempt

Industry Canada

This

transmitter(s)/

receiver(s) that comply with Innovation, Science and Economic

Development Canada’s

licence-exempt RSS(s). Operation

is subject to the following two conditions: (1) This device

may not cause interference. (2) This device must accept any

interference, including interference that may cause undesired

operation of the device.

The term ‘’IC:‘’ before the certification/registration number only

signifies that the Industry Canada technical specifications were

met.

This product meets the applicable Innovation, Science and

Economic Development Canada technical specifications.

RF radiation exposure statement

The product complies with FCC RF radiation exposure limits set

forth for an uncontrolled environment. The Baby Unit should

be installed and operated with a minimum distance of 8 in (20

cm) between the Baby Unit and all persons’ body. Use of other

accessories may not ensure compliance with FCC RF exposure

guidelines. This equipment complies also with Industry Canada

RSS-102 with respect to Canada’s Health Code 6 for Exposure

of Humans to RF Fields.

For cETL compliance only

Mesures de sécurité importantes

La plaque signalétique appliquée est située au bas du socle de

l’unité du bébé.

Lorsque vous utilisez votre appareil, vous devriez toujours suivre

certaines mesures de précaution de base afin de réduire les

risques d’incendie, d’électrocution et de blessures corporelles,

dont ceux qui suivent :

1. Observez toutes les instructions et mises en garde inscrites

sur l’appareil.

L’installation par un adulte est requise.

2.

3. MISE EN GARDE: N’installez pas l’unité du bébé à une hauteur

supérieure à 2 mètres.

4. Ce produit ne remplace pas la surveillance adulte du nourrisson.

La supervision du nourrisson est la responsabilité du parent

ou de la personne qui s’occupe de l’enfant. Ce produit pourrait

cesser de fonctionner et, par conséquent, vous ne devriez pas

présumer qu’il continuera de fonctionner correctement pendant

une période de temps donnée. De plus, il ne s’agit pas d’un

instrument médical et ne devrait pas être utilisé comme tel. Ce

produit est destiné à vous aider à superviser votre bébé.

5. N’utilisez pas cet appareil près de l’eau ni de toute autre

source d’humidité, par exemple, près d’une baignoire, cuve

à lessive, évier de cuisine, dans un sous-sol humide ni près

d’une piscine, dans un soussol humide ou une douche.

6. MISE EN GARDE: Utilisez uniquement la pile fournie. Un

risque d’explosion pourrait survenir si un mauvais type de

pile est utilisé pour l’unité du parent. La pile ne peut pas être

soumise à des températures extrêmes élevées ou basses et à

une faible pression d’air à haute altitude pendant l’utilisation,

l’entreposage ou le transport. L’élimination de la pile dans le

feu ou dans un four chaud, ou l’écrasement ou le découpage

mécanique de la pile peuvent entraîner une explosion. Laisser

la pile dans un environnement à température extrêmement

élevée peut entraîner une explosion ou la fuite d’un liquide ou

d’un gaz inflammable. Une pile soumise à une pression d’air

extrêmement basse peut provoquer une explosion ou une

fuite de liquide ou de gaz inflammable. Éliminer la pile usagée

conformément aux informations du Sceau RBRC.

7. N’utilisez que les adaptateurs inclus avec ce produit.

L’utilisation d’un adaptateur dont la polarité ou la tension

serait inadéquate risque d’endommager sérieusement le

produit et mettre votre sécurité en péril.

8.

9.

Informations sur les adaptateurs électriques :

Adaptateur de l’unité du parent : Sortie : 5V DC 2A

VTech Telecommunications Ltd.

Modèle: VT07EUS05150

Adaptateur de l’unité du bébé : Sortie : 5V DC 1A

VTech Telecommunications Ltd.

Modèle: VT05EUS05100

3.

4.

Informations sur les piles rechargeables :

Zhuhai Great Power Energy Co., Ltd.

Lithium battery, 3.7V 5000mAh;

Modèle: GSP806090-5Ah-3.7V-1S1P

Lorsqu’ils sont branchés dans une prise de courant, les

adaptateurs secteur ont été conçus pour être orientés

correctement, soit à la verticale ou au plancher. Les broches

n’ont pas été conçues pour supporter le poids du bloc

d’alimentation et le maintenir en place si celuici est branché

dans une prise au plafond, sous une table ou dans un meuble.

Pour les PRODUITS À BRANCHER À UNE PRISE DE

COURANT, la prise de courant doit être installée près du

produit, afin d’assurer une accessibilité sécuritaire à la prise

de courant.

10. Débranchez ce produit de la prise de courant avant de

procéder au nettoyage. N’utilisez pas de nettoyants en

aérosols. Utilisez un chiffon humide pour le nettoyer.

11. Ne coupez pas les cordons d’alimentation pour remplacer les

fiches, car ceci peut présenter un danger potentiel.

12. Ne laissez aucun objet reposer ni appuyer sur le cordon

d’alimentation. N’installez pas cet appareil dans un endroit

où l’on risque d’écraser le cordon d’alimentation ou de le

piétiner.

13. Ne faites fonctionner cet appareil qu’avec le type

d’alimentation indiqué sur l’étiquette. Si vous ne connaissez

pas le type d’alimentation que vous possédez à votre

domicile, consultez votre marchand ou votre compagnie

locale d’électricité.

14. Ne surchargez pas les prises de courant murales ni les

rallonges électriques.

15. Ne placez pas cet appareil sur un chariot, meuble, trépied,

support de montage ni table chancelants.

16. Les trous et ouvertures du boîtier, situés à l’arrière de

l’appareil ou sous celui-ci, servent à aérer l’appareil. Pour

l’empêcher de surchauffer, ne bloquez sous aucun prétexte

ces ouvertures et n’empêchez pas l’aération adéquate de

l’appareil en le plaçant sur un lit, divan, tapis ou toute autre

surface similaire. De même, ne le positionnez pas à proximité

ni au-dessus d’une source de chaleur ou d’un calorifère. De

plus, ne placez pas l’appareil dans un endroit avant de vous

assurer qu’il y ait une bonne circulation d’air.

17. N’enfoncez jamais d’objets à travers les ouvertures de cet

appareil, car ils pourraient entrer en contact avec des points de

tension dangereux ou causer des courts-circuits qui peuvent

dégénérer en incendies ou en risques d’électrocution. Ne

renversez jamais de liquide dans ce produit.

18. Afin de réduire les risques d’électrocution, ne démontez

pas cet appareil, mais apportez-le dans un centre de service

autorisé. L’ouverture du boîtier ou le retrait de toutes pièces

que contient cet appareil, à l’exception de l’accès autorisé

à certaines portes ou ouvertures, risque de vous exposer à

des points de tension dangereux ou d’autres dangers. Un

remontage incorrect peut par la suite présenter des risques

d’électrocution.

19. Vous devriez tester la réception chaque fois que vous mettez

l’appareil en fonction.

21.

20. Examinez les composantes afin de vérifier si celles-ci ne sont

pas endommagées.

Il existe un très faible risque de perte de confidentialité

avec certains appareils électroniques (autres écoute-bébés,

téléphones sans fils etc.). Pour l’éviter, s’assurer que le

produit n’a jamais été utilisé avant l’achat, réinitialiser l’unité

de façon périodique, éteindre l’écoute-bébé quand il n’est

pas en cours d’utilisation.

22. Les enfants devraient être supervisés afin de vous assurer

qu’ils ne jouent pas avec l’appareil.

23. Le produit n’est pas conçu pour être utilisé par des personnes

(incluant des enfants) aux capacités physiques, sensorielles

ou mentales réduites ou qui manquent d’expérience et de

connaissances, à moins qu’on leur ait donné suffisamment

de supervision ou d’instructions relativement à l’utilisation de

l’appareil par une personne responsable de leur sécurité.

CONSERVEZ CES INSTRUCTIONS

Mises en garde

1. Utilisez et entreposez le produit à une température entre 0˚

C (32˚F) et 40˚C (104˚ F).

2. N’exposez pas cet appareil à des froids ou des chaleurs

extrêmes, ainsi qu’à la lumière directe du soleil. Ne l’installez

pas près d’une source de chauffage.

Le bloc-piles ne doit pas être exposé à la chaleur excessive

telle que la lumière du soleil ou au feu.

Avertissement - Risque de strangulation

- Les enfants se sont ÉTRANGLÉS dans des

cordons. Gardez ce cordon hors de portée des

enfants (à plus de 0,9 m). N’enlevez pas cette

étiquette.

5. Ne jamais placer le moniteur à l’intérieur du berceau ou du

parc de bébé. Ne jamais couvrir le moniteur ou l’unité (s)

portative avec un article tel une serviette ou une couverture.

6. D’autres équipements électroniques peuvent produire des

interférences sur votre moniteur vidéo et audio. Tentez

d’installer votre moniteur vidéo ou audio à l’écart des appareils

électroniques tels que des routeurs sans fil, radios, téléphones

cellulaires, interphones, moniteurs, téléphones, ordinateurs

personnels, électroménagers et téléphones sans fil.

Stimulateurs cardiaques implantés dans l’organisme

Les simulateurs cardiaques (ne s’applique qu’aux dispositifs

numériques sans fil) :

L’organisme ‘Wireless Technology Research, LLC (WTR)’,

une firme de recherche indépendante, a mené une évaluation

pluridisciplinaire des interférences entre les téléphones sans

fil portatifs et les stimulateurs cardiaques implantés dans

l’organisme. Appuyée par l’Administration des aliments et

drogues (FDA) des États-Unis, la firme WTR recommande aux

médecins:

Avis aux détenteurs de stimulateurs cardiaques

• Vous devriez maintenir les dispositifs sans fil à au moins six

•

pouces du simulateur cardiaque.

Ils ne doivent PAS placer le téléphone sans fil directement sur

le stimulateur cardiaque, tel que dans une poche de chemise,

lorsque celui-ci est en marche.

L’étude effectuée par l’organisme WRS n’a pas identifié de risque

pour les détenteurs de simulateurs cardiaques causés par les gens

qui utilisent dispositifs sans fil à proximité de ceux-ci.

Champs électromagnétiques (EMF)

Ce produit de LeapFrog est conforme à toutes les normes se

rapportant aux champs électromagnétiques (EMF) standard. Si

vous le manipulez correctement en suivant les instructions de

ce guide, son utilisation sera sécuritaire pendant de nombreuses

années, selon les meilleures évidences scientifiques dont nous

disposons aujourd’hui.

Download app for mobile access

Step 1

Download the free LeapFrog baby

monitor mobile app and install it to a

mobile device, then use your mobile

device and the mobile app to monitor

your areas remotely.

1. Press

MENU when the Parent Viewer is in idle.

2. Go to

> Connect Mobile Phone.

3. Scan the QR code in the Parent Viewer to

download the app into your mobile device.

4. Follow the instructions in the mobile app to set

up and pair your Baby Unit to the mobile app.

Alternatively, you can download the mobile app

from the App Store or Google Play store.

or the Google Play

2. Download and install the free LeapFrog mobile

Install the mobile app

1. Browse the App Store

.

store

app to your device.

-OR-

Scan the QR code below to get the app.

Note:

• Make sure your mobile device meets the

minimum requirement for the mobile app.

Minimum requirements:

The mobile app is compatible with:

• AndroidTM 5.0 or later; and

•

iOS 11.0 or later.

Step 2

After installing the mobile app, follow the

instructions in the mobile app and Parent Viewer

to set up and pair your Baby Unit.

In your mobile device:

1. Tap the app icon to run the mobile app in

your mobile device, and then create a user

account.

2. We recommend that you use common

webmail services, such as Google Gmail, for

the registration of your user account. Check

your email (and Spam folder), and activate

your new user account via the email link

Then, sign in to your account.

3. Follow the instructions in the mobile app to

pair the camera. Tap

app to get started.

, then in the mobile

Auto software and firmware update

To ensure that your baby monitor is always at its best performance, the Parent Viewer will

prompt a message and ask you to update its software and the Baby Unit's firmware when there

are new versions available.

• Follow the instructions on the Parent Viewer screen to update your baby monitor.

To check if your device is running on the latest software, or to update your device software, go to:

> Software Update

Connect your baby monitor to Wi-Fi

• You must connect your baby monitor to your secured home Wi-Fi network in order to receive

the latest software and firmware updates. To set Wi-Fi up, go to:

> Configure Wi-Fi > Change Wi-Fi Networks.

Troubleshooting

Symptom

Try this

Why does the baby

monitor not respond

normally?

Try the following (in the order listed) for a common cure:

1. Disconnect the power to the Baby Unit(s) and the Parent Viewer.

2. Wait a few seconds before connecting power back to the Baby Unit(s) and the Parent Viewer.

3. Turn on the Baby Unit(s) and the Parent Viewer.

4. Wait for the Parent Viewer to synchronize with the Baby Unit(s). Allow up to one minute for this

to take place.

Why doesn’t the Baby

Unit’s and Parent

Viewer’s power LED turn

on when I switch on the

units?

The Parent Viewer may not be connected to power. Insert the appliance plug into the power jack

of the Parent Viewer and put the adapter in a wall socket. Then, press the

Power button on the

Parent Viewer to establish connection with the Baby Unit.

The Baby Unit may not be connected to power. Insert the appliance plug into the power jack of the

Baby Unit and put the adapter in a wall socket. Then, slide the On/Off switch on the Baby Unit to

establish connection with the Parent Viewer.

Why are my images in

black and white?

The images are in black white during night-time or in a dark room when night vision is

automatically activated. You can also choose to view your baby at night in color, see Night Vision

(B&W and Color) to learn how.

Why is the Baby Unit

producing a high-pitched

noise?

The Parent Viewer and Baby Unit(s) may be too close to each other.

• Move the Parent Viewer away from the Baby Unit(s) until the noise stops (OR)

• Turn down the volume of your Parent Viewer.

Why does the Parent

Viewer beep?

The Baby Unit(s) may be out of range. Move the Parent Viewer closer to the Baby Unit(s) (but not

less than 3 feet).

Why can’t I hear any

sounds from the Parent

Viewer? Why can’t I

hear my baby cry?

Why can’t I establish a

connection? Why does

my connection cut off

every now and then?

Why are there sound

interruptions?

The Parent Viewer may not have enough battery for the Parent Viewer to perform normally.

Charge the Parent Viewer until the battery icon becomes solid

.

The temperature of your baby’s room may be too high or too low.

The Parent Viewer speaker volume may be too low or muted. Press

adjustment menu, then press

menu to change the Parent Viewer’s sound sensitivity to the highest level (level 5), see Sound

Detection and Auto Wake Up.

to increase the speaker volume. Or you can use the Parent Viewer

to open the volume

The Baby Unit(s) may be out of range. Move the Parent Viewer closer to the Baby Unit(s) (but not

less than 3 feet).

Other electronic and wireless products may cause interference with your baby monitor. Try

installing your baby monitor as far away from these devices as possible.

If you powered on only one Baby Unit but have two paired to the Parent Viewer, your Parent

Viewer may display

turned on via the menu.

and the LINK LED light flashes. Switch to the Baby Unit you have

Customer Support

Visit our Consumer Support website 24 hours a day at:

U.S.: leapfrog.com/support

C.A.: leapfrog.ca/support

Or call our Customer Service number: 1 (800) 701-5327 in the U.S. and Canada during Customer Service hours

Monday to Friday, 9am - 6pm Central Time

Online Help

Find the answer to your questions on our Online Support page . There, you will find information

about product installation, features, operations and settings. Get assisted at your own pace with

video walk-throughs and Frequently Asked Questions.

Visit www.leapfrog.zendesk.com or scan the QR code on the left to enter our Online Support page.

Specifications are subject to change without notice.

© 2021 LeapFrog Enterprises, Inc.,

a subsidiary of VTech Holdings Limited.

All rights reserved. 08/21. LF815-XHD_QSG_V2.

Monitoring mode

1

2

1 2

1

2

1

Help

50

26°C

Select

Exit

Tip:

• Depending on surroundings and obstructing factors that affect signal strength, such as distance and internal

walls, you may experience reduced Wi-Fi signal. To improve the Wi-Fi signal strength, adjust the distance or

direction of your Parent Viewer. Check with your Parent Viewer again.



 

 

 

 

 

 

 

 

 

 

 

 

 

 

VTech Telecommunications Ltd

June 05, 2021

To whom it may concern,

Request for Permanent Confidentiality

Under FCC Part 15 Certification

FCC ID: EW780-2517-00

Request is hereby submitted by VTech Telecommunications Ltd. to withhold

permanently from public review certain portions of the application for equipment

certification for the referenced FCC identifiers. This request for confidentiality is

made pursuant to 47 CFR § 0.457(d) and 0.459 of the FCC Rules. In particular, the

following sections of the application are to be kept permanently confidential and

VTech Telecommunications Ltd. reserves the right to discern which parties can

obtain access to these information:

 Schematics

 Detailed Block diagrams

 Detailed Operational/Functional Description

The rationale for request for confidentiality is as followings:

This information represents intellectual property of VTech Telecommunications Ltd.

and it is subject to competition. We have invested considerable time and materials in

research and development to produce the referenced product. Disclosure of the

permanently confidential portions of this application to competitors would not only

give them significant competitive advantages in developing similar products, but

would also disclose successful implementation of unpublished, leading edge

technology developed by us.

If you have questions or need further information, please contact the undersigned.

Regards,

Michael Tsui

Approbation Supervisor



 

 

 

 

 

 

Appendix B1

Letter of Agency for FCC Certification

June 05, 2021

To whom it may concern,

Letter of Agency

I, an officer of VTech Telecommunications Limited do hereby

authorize Intertek Testing Services (Mr. Kenneth Wong) to act on our

behalf in front of the Federal Communications Commission with respect

to all matters relating to certification of equipment under Part 15 and/or

Part 95 of the FCC Rules until further notice.

I further certify that no party (as defined in §1.2002(b) of CFR 47, 2004) to

this application, including myself, is subject to a denial of federal benefits,

that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug

Abuse Act of 1988, 21 U.S.C., 862.

Regards,

Michael Tsui

Approbation Supervisor