FCC ID: EW780-2839-01 Video Monitor - Parent Unit

Go to www.vtechphones.com to register your product for enhanced warranty support and latest VTech product news. RM7868HD RM7868-2HD 7 Touch Screen Wi-Fi 1080p Pan & Tilt Monitor For more support information S m Quick start guide RM7868HD RM7868-2HD Congratulations on purchasing your new VTech product. Before using this baby monitor, please read the Important safety instructions. For support, shopping, and everything new at VTech, visit our website at www.vtechphones.com. In Canada, visit www.vtechcanada.com. What does HD Video Monitor do?

VTech 7 Touch Screen Wi-Fi 1080p Pan & Tilt Monitor allows you to stay close to your baby when you are on the move or away. This monitor is Wi-Fi enabled, using your home wireless network to stream live video and audio through the 1080p baby unit and 7-inch color screen parent unit. It allows you to maintain a constant connection to your baby. You can also monitor from your smartphone and mobile tablet. VTech 7 Touch Screen Wi-Fi 1080p Pan & Tilt Monitor uses MyVTech Baby Pro app to let you instantly see and hear whats happening with your baby from anywhere in the world. The app can be downloaded from the App Store or the Google PlayTM Store. Important safety instructions The applied nameplate is located at the bottom of the baby units base. When using your equipment, basic safety precautions should always be followed to reduce the risk of re, electric shock and injury, including the following:

1. Follow all warnings and instructions marked on the product. 2. Adult setup is required. 3. CAUTION: Do not install the baby unit at a height above 6.5 feet (2 meters). 4. This product is intended as an aid. It is not a substitute for responsible and proper adult supervision and should not be used as such. 5. This product is not intended for use as a medical monitor. 6. Do not use this product near water. For example, do not use it next to a bath tub, wash bowl, kitchen sink, laundry tub or swimming pool, or in a wet basement or shower. 7. CAUTION: Use only the battery provided. There may be a risk of explosion if a wrong type of battery is used for the parent unit. The battery cannot be subjected to high or low extreme temperature and low air pressure at high altitude during use, storage or transportation. Disposal of battery into re or a hot oven, or mechanically crushing or cutting or the battery can result in an explosion. Leaving the battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of ammable liquid of gas. Battery subjected to extremely low air pressure may result in an explosion or the leakage of ammable liquid or gas. Dispose of used battery according to the information in The RBRC seal. 8. Use only the adapters included with this product. Incorrect adapter polarity or voltage can seriously damage the product. Power adapters information:

Baby Unit Output: 5V DC 1000mA VTech Telecommunications Ltd. Model: VT05EUS05100 Parent Unit Output: 5V DC 2A VTech Telecommunications Ltd. Model: VT07EUS05200 Rechargeable battery information:

3.7V 5000mAh, 18.5Wh Lithium-ion battery Zhuhai Great Power Energy Co., Ltd. Model: GSP806090-5Ah-3.7V-1S1P 9. The power adapter is intended to be correctly oriented in a vertical or oor mount position. The prongs are not designed to hold the plug in place if it is plugged into a ceiling, under-

the-table or cabinet outlet. 10. For pluggable equipment, the socket-outlet (power adapter) shall be installed near the equipment and shall be easily accessible. 11. Unplug this product from the wall outlet before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning. 12. Do not cut off the power adapters to replace them with other plugs, as this causes a hazardous situation. 13. Do not allow anything to rest on the power cords. Do not install this product where the cords may be walked on or crimped. 14. This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply in your home, consult your dealer or local power company. 15. The equipment is to be supplied from an identied USB port complying with the requirements of Limited Power Source. 16. Do not overload wall outlets or use an extension cord. 17. Do not place this product on an unstable table, shelf, stand or other unstable surfaces. 18. This product should not be placed in any area where proper ventilation is not provided. Slots and openings in the back or bottom of this product are provided for ventilation. To protect them from overheating, these openings must not be blocked by placing the product on a soft surface such as a bed, sofa or rug. This product should never be placed near or over a radiator or heat register. 19. Never push objects of any kind into this product through the slots because they may touch dangerous voltage points or create a short circuit. Never spill liquid of any kind on the product. 20. To reduce the risk of electric shock, do not disassemble this product, but take it to an authorized service facility. Opening or removing parts of the product other than specied access doors may expose you to dangerous voltages or other risks. Incorrect reassembling can cause electric shock when the product is subsequently used. 21. You should test the sound reception every time you turn on the units or move one of the components. 22. Periodically examine all components for damage. 23. There is a very low risk of privacy loss when using certain electronic devices, such as baby monitors, cordless telephones, etc. To protect your privacy, make sure the product has never been used before purchase, reset the baby monitor periodically by powering off and then powering on the units, and power off the baby monitor if you will not use it for some time. 24. Children should be supervised to ensure that they do not play with the product. 25. The small parts of this monitor can be swallowed by babies or small children. Keep these parts out of reach of children. 26. The product is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. SAVE THESE INSTRUCTIONS Cautions Use and store the product at a temperature between 32oF and 104oF. Burn hazard, re hazard, explosion hazard associated with mishandling of the battery. Do not expose the product to extreme cold, heat or direct sunlight. Do not put the product close to a heating source. WarningStrangulation HazardChildren have STRANGLED in cords. Keep this cord out of the reach of children (more than 3 ft (0.9m) away). Do not remove this tag. Never place the camera unit(s) inside the babys crib or playpen. Never cover the camera unit(s) or parent unit with anything such as a towel or a blanket. Other electronic products may cause interference with your camera unit. Try installing your camera unit as far away from these electronic devices as possible: wireless routers, radios, cellular telephones, intercoms, room monitors, televisions, personal computers, kitchen appliances and cordless telephones. Precautions for users of implanted cardiac pacemakers Cardiac pacemakers (applies only to digital cordless devices):

Wireless Technology Research, LLC (WTR), an independent research entity, led a multidisciplinary evaluation of the interference between portable wireless devices and implanted cardiac pacemakers. Supported by the U.S. Food and Drug Administration, WTR recommends to physicians that:

Pacemaker patients Should keep wireless devices at least six inches from the pacemaker. Should NOT place wireless devices directly over the pacemaker, such as in a breast pocket, when it is turned ON. WTRs evaluation did not identify any risk to bystanders with pacemakers from other persons using wireless devices. Electromagnetic elds (EMF) This VTech product complies with all standards regarding electromagnetic elds (EMF). If handled properly and according to the instructions in this users manual, the product is safe to be used based on scientic evidence available today. All rights reserved. 05/22. RM7766-XHD_QSG_V1 2022 VTech Communications, Inc. Specifications are subject to change without notice. How the system works Direct mode The parent unit and the baby unit of your video monitor connect to each others in Direct mode by default, which allows you to stream live video right out of the box. Direct mode connection lets you stream live video from parent unit only. Overview Baby unit overview Parent unit overview Whats in the box Your baby monitor package contains the following items. Save your sales receipt and original packaging in the event warranty service is necessary. Download app for mobile access 1 Download the free MyVTech Baby Pro mobile app and install it to a mobile device, then use your mobile device and the mobile app to monitor your areas remotely. 1. Press MENU when the parent unit is idle. 2. Go to > > Connect Mobile Phone. 3. Scan the QR code in the parent unit to download the app into your mobile device. 4. Follow the instructions in the mobile app to set up and pair your baby unit to the mobile app. Alternatively, you can download the mobile app from the App Store or Google Play store. Install MyVTech Baby Pro mobile app Quick start guide Requirements For mobile access:

MyVTech Baby Pro mobile app Network Wi-Fi router Internet connection x 2 x 2 1 set for RM7868HD 2 sets for RM7868-2HD Wi-Fi 2.4GHz 802.11 b/g/n 1.5 Mbps @ 720p or 2.5 Mbps @1080p upload bandwidth per baby unit or the Google Play store 1. Browse the App Store 2. Search for the mobile app with the keyword myvtech baby pro. 3. Download and install the MyVTech Baby Pro mobile app to your mobile device. OR Scan the QR codes on the right to get the app. Make sure your mobile device meets the minimum requirement for the mobile app. Minimum requirement The mobile app is compatible with:

AndroidTM 6.0 or later; and iOS 12 or later. 2 After installing the mobile app, follow the instructions in the mobile app and parent unit to set up and pair your baby unit. In your mobile device:

1. Tap to run the mobile app in your mobile device, and then create a user account. 2. We recommend that you use common webmail services, such as Google Gmail for registration of your user account. Check your email (and Spam folder), and activate your new camera account via the email link, then sign in to your account. 3. Follow the instructions in the mobile app to pair the camera. Tap

, then Add Camera in the mobile app to get started. 1 2 3 4 5 9 10 11 6 7 8 12 13 1 2 3 4 5 6 7 Light sensor Camera lens Infrared LEDs Allow you to see clearly in a dark environment. Microphone Night Light Night Light Control Key Go to Night Light section to learn more. LED indicator Red is steadily on when the baby unit is connecting to the parent unit in direct mode. Green is steadily on when the baby unit is connected in Wi-Fi router mode. Red ashing slowly during video streaming in direct mode. Green ashes slowly during video streaming in Wi-Fi router mode. ON/OFF switch Power it on or off. Speaker Temperature sensor Power jack 8 9 10 11 12 Wall mount slots 13 PAIR Press and hold for three seconds to enter pairing mode. Reset the baby unit to factory default. 1. Press and hold PAIR key until you hear a beep sound. 2. Release the PAIR key, and then press the PAIR key again ve times until you hear another beep sound. 3. The baby unit will sound another beep when the reset completes. Then, the baby unit will reboot. CABLE MANAGEMENT Connect, charge and power on the baby monitor Connect the baby monitor Charge the parent unit battery before use The rechargeable battery in the parent unit is built-in. Use only the power adapters supplied with this product. Make sure the parent unit and the baby unit are not connected to the switch controlled electric outlets. Connect the power adapters in a vertical or oor mount position only. The adapters prongs are not designed to hold the weight of the parent unit and the baby unit, so do not connect them to any ceiling, under-the-table, or cabinet outlets. Otherwise, the adapters may not properly connect to the outlets. Make sure the parent unit, the baby unit and the power adapter cords are out of reach of children. The parent unit runs on rechargeable battery or AC power. To continuously monitor your baby, keep the parent unit connected to AC power. Before using the baby monitor for the rst time, charge the parent unit battery for 12 hours. When the parent unit battery is fully charged, the battery icon becomes solid

. The standby time varies depending on your actual use. After the parent unit is fully charged, press Power until the welcoming screen appears. IOS is a trademark or registered trademark of Cisco in the U.S. and other countries and is used under license. App Store is a trademark of Apple Inc., registered in the U.S. and other countries. Android TM and Google Play TM are trademarks of Google Inc. Local access C22.2 NO.62368-1 CSA STD. CERTIFIED TO 62368-1 UL STD. CONFORMS TO You may experience reduced signal strength if your parent unit and baby unit are far apart, or there are obstructing factors, such as internal walls, between them. Move the parent unit closer to the baby unit to improve the signal strength. Protect your privacy and online security 1 2 3 Phone: 1 (800) 595-9511 in the U.S. or 1 (800) 267-7377 in Canada Address: 9020 SW Washington Square Road - Ste 555 Tigard, OR 97223, United States Company: VTech Communications, Inc. responsibility for any loss or claims by third parties that may arise through the use of this product. resulting from the use of this users manual. VTech Communications, Inc. and its suppliers assume no VTech Communications, Inc. and its suppliers assume no responsibility for any damage or loss Disclaimer and Limitation of Liability Parent unit battery: 3.7V 5000mAh, 18.5Wh Lithium-ion battery Parent unit power adapter: Output: 5V DC, 2A. Baby unit power adapter: Output: 5V DC, 1000mA. Power requirement vary according to environmental conditions at the time of use. Maximum power allowed by FCC and IC. Actual operating range may Nominal effective range

(IPS 1280x800 pixels) 7 Color LCD 11 LCD Channels Wi-Fi Router mode To stream live video with better connection, you can also set up your monitor in Router mode connection. Router mode uses your home Wi-Fi network to connect the video monitor. It supports streaming live video through the parent unit and MyVTech Baby Pro app. Download and install the MyVTech Baby Pro mobile app to stream remotely. With the mobile app, your Wi-Fi router (not included) serves as a communicating channel between your baby unit and mobile device, allowing you to monitor and control your baby unit wherever you are. For details, see Download app for mobile access section in this quick start guide. Connecting Wi-Fi to enhance local access Auto mode With Auto mode connection, the parent unit will automatically select the most reliable connection mode (Direct or Wi-Fi) when connecting to the baby unit(s). Mobile app access will not be interrupted in Auto mode. VTech cares about your privacy and peace of mind. Thats why weve put together a list of industry-recommended best practices to help keep your wireless connection private and your devices protected when online. We recommend you carefully review and consider complying with the following tips. Ensure your wireless connection is secure. Before installing a device, ensure your routers wireless signal is encrypted by selecting the WPA2-PSK with AES setting in your routers wireless security menu. Mobile access Change default settings. Change your wireless routers default wireless network name (SSID) to something unique. Change default passwords to unique, strong passwords. A strong password:

Press and hold The battery icon indicates the battery status (see the following table). Battery indicators Battery status Action

- Is at least 10 characters long.

- Is complex.

- Does not contain dictionary words or personal information.

- Contains a mix of uppercase letters, lowercase letters, special characters and numbers. Keep your devices up to date. Download security patches from manufacturers as soon as they become available. This will ensure you always have Slide the switch to ON to power on your baby unit. the latest security updates. If the feature is available, enable automatic updates for future releases. Disable Universal Plug and Play (UPnP) on your router. UPnP enabled on a router can limit the effectiveness of your rewall by allowing other network devices to open inbound ports without any intervention or approval from you. A virus or other malware program could use this function to compromise security for the entire network. For more information on wireless connections and protecting your data, please review the following resources from industry experts:

1. Federal Communications Commission: Wireless Connections and Bluetooth Security Tips www.fcc.gov/consumers/guides/how-protect-yourself-online. 2. U.S. Department of Homeland Security: Before You Connect a New Computer to the Internet www.us-cert.gov/ncas/tips/ST15-003. 3. Federal Trade Commission: Using IP Cameras Safely https://www.consumer.ftc.gov/articles/0382-using-ip-cameras-safely. 4. Wi-Fi Alliance: Discover Wi-Fi Security http://www.wi-.org/discover-wi-/security. When powering up, the baby units status LED turns on. It will turn off after a while and keeps off. The status LED is set to off by default. WARM NOTE:

Camera lens and surface may get warm during normal operation. The screen displays The LED light ashes. and

. The battery has very little charge and may be used for only a short time. Charge without interruption (about 30 minutes). The battery icon becomes solid

. The battery is fully charged. To keep the battery charged, connect it to AC power when not in use. Raise the parent unit antenna for better reception Baby unit: 2412 - 2462 MHz Frequency When both parent unit and app are viewing the camera simultaneously, the video quality will be optimised to deliver the best possible viewing result.

12 13 14 15 1 2 3 4 5 6 7 8 9 10 11 16 1 2 3 4 3- level sound indicator light Green: low sound level is detected by the baby unit. Green and amber: moderate sound level is detected by the baby unit. Green, amber and red: high sound level is detected by the baby unit. LINK LED light On when the parent unit is linked to the baby unit. Flashes when the link to the baby unit is lost. LED light On when the parent unit is connected to AC power, and the battery is charging. Flashes when the parent unit battery is low and needs to be charged. TALK /

Press and hold to talk to the baby unit. While in a sub-menu, press to exit. 6

Arrow keys Press to navigate leftward, upward, rightward or downward, within the main menu and sub-menus. While viewing a zoomed image, press to move the image leftward, upward, rightward or downward.

Increase or decrease parent unit volume. Zoom Press to zoom in/out. While in a sub-menu, press to view the help menu. Power | LCD ON/OFF 7 8 9 10 Microphone 11 Touch screen 12 Antenna 5 MENU | SELECT Press to enter the main menu. While in a menu, press to choose an item, or save a setting. 13 14 15 Speaker Power jack RESET Force reboot the parent unit. 16 Stand Parent unit icons Main Menu Options Main Menu Options Monitoring mode (* For RM7868-2HD only) View baby units in Single mode. View baby units in Patrol mode. View baby units in Split screen. Night light Turn on or turn off night light. Select a night light color. Adjust night light brightness. Set a night light timer. Melodies and soothing sounds Select play all melodies, or play one of the ve melodies and ve soothing sounds. You can also set the timer to stop playing after 15, 30 or 60 minutes, or playing non-stop. Adjust baby unit speaker volume. General settings Wi-Fi settings Congure Wi-Fi Connect to mobile phone Selection Connection Mode Connection Status Turn on/off parking mode Adjust parent unit screen brightness Set screen lock timer Set screen off timer Temperature display format Languages, reset settings, software update. Alerts Settings Adjust alerts volume Turn on/off temperature alert Select maximum and minimum temperature for alert range. Turn on/off low battery alert tone Turn on/off motion detection alert tone Select motion sensitivity level. Turn on/off no link alert Help and info Support information System information Privacy information Status icons Direct mode Parent unit, baby unit 1 and baby unit 2

(*For RM7868-2HD only) are connected to each others directly. Wi-Fi Router mode Parent unit, baby unit 1 and baby unit 2

(*For RM7868-2HD only) are connected to home Wi-Fi network. Baby unit 1 and 2 are being viewed in Patrol mode (*For RM7868-2HD only). Baby unit 1 and 2 are being viewed in Split mode (*For RM7868-2HD only). Touch screen is locked. Night vision is turned on. Motion detection alert is turned on. Melodies and soothing sounds are playing. Night light is turned on. Auto night light brightness is activated. Temperature alert is turned on. Parent unit is muted. Temperature is lower than 68F. Temperature is within 68F and 75F. Temperature is higher than 75F. Battery indicator. Basic operation After powering up your video monitor, the parent unit streams live video in direct mode. We recommend you follow the instructions on screen to set up home Wi-Fi network with your monitor for functionality enhancements and mobile access. See Auto software and rmware update and Download app for mobile access in this quick start guide. Use the Control Panel Tap the screen to open and use the Control Panel. Tap to lock the panel, and tap to unlock it. Use the Main Menu Press MENU on the parent unit to enter the main menu, choose a menu item, or save a setting. You can use the parent unit menu for advanced settings or operations, such as to play or stop the baby unit lullaby, or adjust the baby unit sound sensitivity. While in the menu:

menu options. Press

to scroll among the Press SELECT to select an item. Press TALK to return to the live video. Press to go to the Help & info page. Adjust speaker volume

Press speaker volume level received from the baby unit. to adjust the parent unit Zoom to zoom in or out in a xed Press zoom sequence. indicates that the image is magnied 3 times. Muted Talk to your baby via the baby unit 1. Press and hold the TALK key. 2. When the icon displays on screen, speak to your parent unit. Your voice is transmitted to the baby unit. 3. When nished talking, release the TALK key to hear your baby again. Turn on/off the parent unit screen You can turn on or turn off the parent unit screen without powering off the unit. You will still hear sounds from the baby unit. Press

| LCD ON/OFF on the parent unit to turn off the screen. Press any key on the parent unit to turn the screen on again. You can reset the parent unit by pressing the RESET key at the back of the unit. Insert a pin into the RESET hole on the back of the parent unit, and then press the key inside. Night Light Test the sound level and position the baby monitor You can control the night light remotely on the parent unit or directly on the baby unit. Testing the sound level of the baby monitor Press and hold On the baby unit:

On the parent unit:

1. Press MENU. 2. Press or to scroll to Night Light menu, then press MENU or to enter. 3. Press or to choose below options:

Turn on/off night light Change night light color Night Light Control Key Adjust night light brightness Single Tap: Turn on/off Set night light timer Tap and hold: Adjust night light brightness This baby monitor is intended as an aid. It is not a substitute for proper adult supervision, and should not be used as such. For hearing protection, make sure the parent unit is more than 3 feet away from the baby unit. If you hear any high-pitched noise from the parent unit, move the parent unit further until the noise stops. You can also press on the parent unit to lower or mute the noise.

> 3ft (1m) Increase the parent unit speaker volume if you cannot hear the sounds transmitted from the baby unit. 3. To avoid causing high-pitched screeching noise from your baby monitor:

Make sure your baby unit and parent unit are more than 3 feet apart; OR Turn down the volume of your parent unit.

To ensure that your baby monitor is always at its best performance, the parent unit will prompt you to update its software and the baby unit rmware when there are new versions available. Follow the instructions on the parent unit screen to update your baby monitor. If you skip the updates, the parent unit and baby unit will be updated automatically when the parent unit is powered off, and then powered on again. To check if your device is running on the latest software or to update your device software, go to:

> > Connect Mobile Phone Connect your baby monitor to Wi-Fi You must connect your video monitor to your secured home Wi-Fi network in order to receive the latest software and rmware updates. To set it up, go to:

For RM7868-2HD only

> 3ft Press and hold Monitoring Modes When more than one baby unit is paired to the parent unit, you can choose to view different baby units in three monitoring modes. Learn more about each below:

Positioning the baby monitor Single Mode Split Mode Patrol Mode The screen displays images only from the selected baby unit in full screen. The screen displays images from all paired baby units at the same time in split view. The screen displays a single cam view that transitions to a different baby unit every 10 seconds. Change the monitoring mode:

1. Press MENU when the parent unit is idle. 2. Press MENU or to enter Monitoring Mode menu. Keep the baby unit out of the reach of your baby. Never place or mount the baby unit inside the babys crib or playpen. 1. Place the baby unit more than 3 feet away 2. Adjust the angle of the baby unit to aim from your baby. at your baby. 3. Press or to choose between Single mode options. Press SELECT to conrm.

, Split

, and Patrol monitoring mount the baby unit (optional) NONONotes Check for reception strength and camera angle of the baby unit before drilling the holes. The types of screws and plugs you need depend on the composition of the wall. You may need to purchase the screws and plugs separately to mount your baby units. 1. Place the wall mount bracket on a wall and then use a pencil to mark two holes in parallel. Remove the wall mount bracket and drill two holes in the wall (7/32 inch drill bit). 3. Align the wall mount bracket and screws with the holes in the wall as shown. Tighten the screw in the middle hole rst, so that the wall mount bracket position is xed. You can tighten the other screw in the top hole. 4. Place the baby unit on the wall mount bracket, and then slide it forward until it locks into place. Connect the power adapter to the baby unit and a power supply not controlled by a wall switch. 2. If you drill the holes into a stud, go to step 3. If you drill the holes into an object other than a stud, insert the wall plugs into the holes. Tap gently on the ends with a hammer until the wall plugs are ush with the wall. 3. Insert the screws into the holes and tighten the screws until only 1/4 inch of the screws are exposed. OR 4. Place the baby unit on the wall mount bracket, and then slide it forward until it locks into place. Align the holes on the wall mount bracket with the screws on the wall, and slide the wall mount bracket down until it locks into place. 1 2 5. You can maximize your baby units viewing angles by tilting the wall mount bracket. Hold the baby unit, and then rotate the knob in anticlockwise direction. This will loosen the joint of the wall mount bracket. Tilt your baby unit up or down to adjust to your preferred angle. Then, rotate the knob in clockwise direction to tighten the joint and secure the angle. General product care The RBRC seal To keep this product working well and looking good, follow these guidelines:

Avoid placing it near heating appliances and devices that generate electrical noise (for example, motors or uorescent lamps). DO NOT expose it to direct sunlight or moisture. Avoid dropping the product or treating it roughly. Clean with a soft damp cloth. DO NOT immerse the parent unit and the baby unit in water and do not clean them under the tap. DO NOT use cleaning spray or liquid cleaners. Make sure the parent unit and the baby unit are dry before you connect them to the mains again. Clean the USB charging port of dust, dirt, and lint regularly. Storage When you are not going to use the video monitor for some time, store the parent unit, the baby unit and the adapters in a cool and dry place. Frequently asked questions Below are the questions most frequently asked about the video monitor. Can I turn the parent unit display screen off but keep hearing sounds from the baby unit?

Why is the baby unit not responding normally?

Why is my screen in black and white?

Why does my baby unit show ofine? Why is the connection lost every now and then?

Why cant I hear a sound/Why cant I hear my baby crying?

| LCD ON/OFF on the parent unit to turn off the screen. The parent Yes, press unit display will also dim automatically after being inactive for some time. In both instances, you will still be able to hear all sounds from the baby unit. Press any key to turn the screen back on. Try the following (in the order listed) for a common cure:

1. Disconnect the power to the baby unit. 2. Wait a few minutes before connecting power back to the baby unit. 3. Reboot the parent unit. The baby unit has a light sensor that measures ambient light. When the ambient light is dim, such as during night time or in a dark room, the baby unit activates its infrared LEDs, and displays the camera images in black and white night vision. The baby unit may have lost connection to the Wi-Fi router. Check your network and router settings. Other electronic products may cause interference with your baby unit. Try installing your baby unit as far away from these electronic devices as possible. The parent unit speaker volume may be too low. Press to increase the volume. on the parent unit You may have set a low sound sensitivity level. Set the sound sensitivity to a higher level. For details, go to www.vtechphones.com for online help topics. The RBRC seal on the lithium-ion battery indicates that VTech Communications, Inc. is voluntarily participating in an industry program to collect and recycle these batteries at the end of their useful lives, when taken out of service within the United States and Canada. The program provides a convenient alternative to placing used lithium-ion batteries into the trash or municipal waste, which may be illegal in your area. VTechs participation makes it easy for you to drop off the spent product at local retailers participating in the program or at authorized VTech product service centers. Please call 1 (800) 8 BATTERY for information on Li-ion battery recycling and disposal bans/restrictions in your area. VTechs involvement in this program is part of its commitment to protecting our environment and conserving natural resources. The RBRC Seal and 1 (800) 8 BATTERY are registered trademarks of Call2recycle, Inc. FCC and IC regulations Increase the separation between the equipment and receiver. FCC Part 15 NOTE: This equipment has been tested and found to comply with the requirements for a Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These requirements are intended to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. WARNING: Changes or modications to this equipment not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that can be safely absorbed by a user or bystander according to the intended usage of the product. This product has been tested and found to comply with the FCC criteria. The baby unit shall be installed and used such that parts of all persons body are maintained at a distance of approximately 8 in

(20 cm) or more. The transmitter and antenna of the parent unit shall be held at least 1 in (2.5 cm) from your face. This Class B digital apparatus complies with Canadian requirement:

CAN ICES-3 (B)/NMB-3(B) Industry Canada This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interference. (2) This device must accept any interference, including interference that may cause undesired operation of the device. The term IC: before the certication/registration number only signies that the Industry Canada technical specications were met. This product meets the applicable Innovation, Science and Economic Development Canada technical specications. RF radiation exposure statement The product complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. The baby unit should be installed and operated with a minimum distance of 8 in (20 cm) between the baby unit and all persons body. Use of other accessories may not ensure compliance with FCC RF exposure guidelines. This equipment complies also with Industry Canada RSS-102 with respect to Canadas Health Code 6 for Exposure of Humans to RF Fields. California Energy Commission battery charging testing mode This video monitor meets the California Energy Commission (CEC) regulations for energy consumption. Your video monitor is set up to comply with the energy-conserving standards right out of the box. Follow the instructions to install and charge the battery. The CEC battery charging testing mode is activated while charging. Even if the parent unit is paired to camera units, the CEC battery charging testing mode is activated while it is powered off and charging.

< 3ft (1m)

test the location for the baby unit If you plan to install your baby unit in a designated location, and use your home Wi-Fi network to connect your video monitor, you need to test which of your selected monitoring areas within the house have good Wi-Fi signal strength. After you have powered on your parent unit, you can use your parent units Wi-Fi signal strength indicator to assist in checking. Once you have identied the suitable location, you can install your baby unit. Adjust the distance between your baby unit and the Wi-Fi router if needed. Depending on surroundings and obstructing factors, such as the effect distance and internal walls have on signal strength, you may experience reduced Wi-Fi signal. To improve the Wi-Fi signal strength, adjust the distance or direction of your parent unit. Check with your parent unit again. For cETL compliance only La plaque signaltique applique est situe au bas du socle de lunit du bb. Lorsque vous utilisez votre appareil, vous devriez toujours suivre certaines mesures de prcaution de base an de rduire les risques dincendie, dlectrocution et de blessures corporelles, dont ceux qui suivent:

1. Observez toutes les instructions et mises en garde inscrites sur lappareil. 2. Linstallation par un adulte est requise. 3. MISE EN GARDE: Ninstallez pas lunit du bb une hauteur suprieure 2 mtres. 4. Ce produit a t conu pour tre un dispositif dappoint seulement. Il nest pas le remplacement dune supervision responsable et adquate par un adulte et ne devrait pas tre utilis comme telle. 5. Ce produit nest pas conu pour tre utilis en tant que moniteur mdical. 6. Nutilisez pas cet appareil prs de leau ni de toute autre source dhumidit, par exemple, prs dune baignoire, cuve lessive, vier de cuisine, dans un sous-sol humide ni prs dune piscine, dans un soussol humide ou une douche. 7. MISE EN GARDE: Utilisez uniquement la pile fournie. Un risque dexplosion pourrait survenir si un mauvais type de pile est utilis pour lunit du parent. La pile ne peut pas tre soumise des tempratures extrmes leves ou basses et une faible pression dair haute altitude pendant lutilisation, lentreposage ou le transport. Llimination de la pile dans le feu ou dans un four chaud, ou lcrasement ou le dcoupage mcanique de la pile peuvent entraner une explosion. Laisser la pile dans un environnement temprature extrmement leve peut entraner une explosion ou la fuite dun liquide ou dun gaz inammable. Une pile soumise une pression dair extrmement basse peut provoquer une explosion ou une fuite de liquide ou de gaz inammable. liminer la pile usage conformment aux informations du Sceau RBRC. 8. Nutilisez que les adaptateurs inclus avec ce produit. Lutilisation dun adaptateur dont la polarit ou la tension serait inadquate risque dendommager srieusement le produit et mettre votre scurit en pril. Informations sur les adaptateurs lectriques :

Sortie : 5 V CC 1000mA. VTech Telecommunications Ltd. Modle : VT05EUS05100 Sortie : 5 V CC 2A. VTech Telecommunications Ltd. Modle : VT07EUS05200 Informations sur les piles rechargeables :

3.7V 5000mAh, 18.5Wh Lithium-ion batterie Zhuhai Great Power Energy Co., Ltd. Modle : GSP806090-5Ah-3.7V-1S1P 9. Lorsquils sont branchs dans une prise de courant, les adaptateurs secteur ont t conus pour tre orients correctement, soit la verticale ou au plancher. Les broches nont pas t conues pour supporter le poids du bloc dalimentation et le maintenir en place si celuici est branch dans une prise au plafond, sous une table ou dans un meuble. 10. Pour les appareils raccords, la prise de courant (de ladaptateur secteur) doit tre installe prs de lquipement et doit tre facilement accessible. 11. Dbranchez ce produit de la prise de courant avant de procder au nettoyage. Nutilisez pas de nettoyants en arosols. Utilisez un chiffon humide pour le nettoyer. 12. Ne coupez pas les cordons dalimentation pour remplacer les ches, car ceci peut prsenter un danger potentiel. 13. Ne laissez aucun objet reposer ni appuyer sur le cordon dalimentation. Ninstallez pas cet appareil dans un endroit o lon risque dcraser le cordon dalimentation ou de le pitiner. 14. Ne faites fonctionner cet appareil quavec le type dalimentation indiqu sur ltiquette. Si vous ne connaissez pas le type dalimentation que vous possdez votre domicile, consultez votre marchand ou votre compagnie locale dlectricit. 15. Lquipement doit tre fourni partir dun acquiescement gauche identi dUSB aux conditions de la source dnergie limite. 16. Ne surchargez pas les prises de courant murales ni les rallonges lectriques. 17. Ne placez pas cet appareil sur un chariot, meuble, trpied, support de montage ni table chancelants. 18. Les trous et ouvertures du botier, situs larrire de lappareil ou sous celui-ci, servent arer lappareil. Pour lempcher de surchauffer, ne bloquez sous aucun prtexte ces ouvertures et nempchez pas laration adquate de lappareil en le plaant sur un lit, divan, tapis ou toute autre surface similaire. De mme, ne le positionnez pas proximit ni au-dessus dune source de chaleur ou dun calorifre. De plus, ne placez pas lappareil dans un endroit avant de vous assurer quil y ait une bonne circulation dair. 19. Nenfoncez jamais dobjets travers les ouvertures de cet appareil, car ils pourraient entrer en contact avec des points de tension dangereux ou causer des courts-circuits qui peuvent dgnrer en incendies ou en risques dlectrocution. Ne renversez jamais de liquide dans ce produit. 20. An de rduire les risques dlectrocution, ne dmontez pas cet appareil, mais apportez-le dans un centre de service autoris. Louverture du botier ou le retrait de toutes pices que contient cet appareil, lexception de laccs autoris certaines portes ou ouvertures, risque de vous exposer des points de tension dangereux ou dautres dangers. Un remontage incorrect peut par la suite prsenter des risques dlectrocution. 21. Vous devriez tester la rception chaque fois que vous mettez lappareil en fonction. 22. Examinez les composantes an de vrier si celles-ci ne sont pas endommages. 23. Il existe un trs faible risque de perte de condentialit avec certains appareils lectroniques (autres coute-bbs, tlphones sans ls etc.). Pour lviter, sassurer que le produit na jamais t utilis avant lachat, rinitialiser lunit de faon priodique, teindre lcoute-bb quand il nest pas en cours dutilisation. 24. Les enfants devraient tre superviss an de vous assurer quils ne jouent pas avec lappareil. 25. Les petites pices de ce moniteur peuvent tre avales par les bbs ou les petits enfants. Veuillez tenir ces pices hors de porte des enfants. 26. Le produit nest pas conu pour tre utilis par des personnes

(incluant des enfants) aux capacits physiques, sensorielles ou mentales rduites ou qui manquent dexprience et de connaissances, moins quon leur ait donn sufsamment de supervision ou dinstructions relativement lutilisation de lappareil par une personne responsable de leur scurit. CONSERVEZ CES INSTRUCTIONS Mises en garde Utilisez et entreposez le produit une temprature entre 0 C

(32F) et 40C (104 F). Risque de brlure, risque dincendie, risque dexplosion associ une mauvaise manipulation de la batterie. Nexposez pas cet appareil des froids ou des chaleurs extrmes, ainsi qu la lumire directe du soleil. Ne linstallez pas prs dune source de chauffage. Avertissement - Risque de strangulation -

Les enfants se sont TRANGLS dans des cordons. Gardez ce cordon hors de porte des enfants ( plus de 0,9 m). Nenlevez pas cette tiquette. Ne jamais placer le moniteur lintrieur du berceau ou du parc de bb. Ne jamais couvrir le moniteur ou lunit (s) portative avec un article tel une serviette ou une couverture. Dautres produits lectroniques peuvent causer des interfrences auprs de votre camra IP. Essayez dinstaller votre camra IP le plus loin possible de ces dispositifs lectroniques : routeurs sans l, radios, tlphones cellulaires, interphones, moniteurs de pices, tlviseurs, ordinateurs personnels, appareils lectriques de cuisine et tlphones sans l. Stimulateurs cardiaques implants dans lorganisme Les simulateurs cardiaques (ne sapplique quaux dispositifs numriques sans l):

Lorganisme Wireless Technology Research, LLC (WTR), une rme de recherche indpendante, a men une valuation pluridisciplinaire des interfrences entre les tlphones sans l portatifs et les stimulateurs cardiaques implants dans lorganisme. Appuye par lAdministration des aliments et drogues (FDA) des tats-Unis, la rme WTR recommande aux mdecins:

Avis aux dtenteurs de stimulateurs cardiaques Vous devriez maintenir les dispositifs sans l au moins six pouces du simulateur cardiaque. Ils ne doivent PAS placer le tlphone sans l directement sur le stimulateur cardiaque, tel que dans une poche de chemise, lorsque celui-ci est en marche. Ltude effectue par lorganisme WRS na pas identi de risque pour les dtenteurs de simulateurs cardiaques causs par les gens qui utilisent dispositifs sans l proximit de ceux-ci. Champs lectromagntiques (EMF) Ce produit de VTech est conforme toutes les normes se rapportant aux champs lectromagntiques (EMF) standard. Si vous le manipulez correctement en suivant les instructions de ce guide, son utilisation sera scuritaire pendant de nombreuses annes, selon les meilleures vidences scientiques dont nous disposons aujourdhui. Need help?

For instructions and guides to make the best use of your baby monitor, and for the latest information and support, check out our online help topics and FAQs. The online help page will also be updated periodically to reect product system updates. Use your smartphone or mobile device to access our online help. Go to https://help.vtechphones.com/RM7868HD or https://help.vtechphones.com/RM7868-2HD; OR Scan the QR code on the right. Launch the camera app or QR code scanner app on your smartphone or tablet. Hold the devices camera up to the QR code and frame it. Tap the notication to be redirected to the online help page.

If the QR code is not clearly displayed, adjust your cameras focus by moving your device closer or further away until the image is clear. S m RM7868HD online help If you would like to contact us, visit https://help.vtechphones.com/cs. You can also call our Customer Support at 1-844-848-8324 (1-844-84-VTECH) [in US] or 1-888-211-2005 [in Canada] for help. Limited warranty What does this limited warranty cover?

The manufacturer of this VTech Product warrants to the holder of a valid proof of purchase (Consumer or you) that the Product and all accessories provided in the sales package (Product) are free from defects in material and workmanship, pursuant to the following terms and conditions, when installed and used normally and in accordance with the Product operating instructions. This limited warranty extends only to the Consumer for Products purchased and used in the United States of America and Canada. What will VTech do if the Product is not free from defects in materials and workmanship during the limited warranty period (Materially Defective Product)?

During the limited warranty period, VTechs authorized service representative will replace at VTechs option, without charge, a Materially Defective Product. If we choose to replace the Product, we may replace it with a new or refurbished Product of the same or similar design. We will retain defective parts, modules, or equipment. Replacement of the Product, at VTechs option, is your exclusive remedy. VTech will return the replacement Products to you in working condition. You should expect the replacement to take approximately 30 days. How long is the limited warranty period?

The limited warranty period for the Product extends for ONE (1) YEAR from the date of purchase (90 days on products purchased as Refurbished*). This limited warranty also applies to the replacement Product for a period of either (a) 90 days from the date the replacement Product is shipped to you or (b) the time remaining on the original one-year warranty (90-day limited warranty on products that are purchased as Refurbished*); whichever is longer.

*Refurbished products purchased from our online store carry a 90-day replacement warranty. What is not covered by this limited warranty?

This limited warranty does not cover:

1. Product that has been subjected to misuse, accident, shipping or other physical damage, improper installation, abnormal operation or handling, neglect, inundation, re, water or other liquid intrusion; or 2. Product that has been damaged due to repair, alteration or modication by anyone other than an authorized service representative of VTech; or 3. Product to the extent that the problem experienced is caused by signal conditions, network reliability, or cable or antenna systems; or 4. Product to the extent that the problem is caused by use with non-VTech accessories; or 5. Product whose warranty/quality stickers, product serial number plates or electronic serial numbers have been removed, altered or rendered illegible; or 6. Product purchased, used, serviced, or shipped for repair from outside the United States of America or Canada, or used for commercial or institutional purposes (including but not limited to Products used for rental purposes); or 7. Product returned without a valid proof of purchase (see item 2 below); or 8. Charges for installation or set up, adjustment of customer controls, and installation or repair of systems outside the unit. RM7868-2HD online help How do you get warranty service?

To obtain warranty service in the USA, please visit our website at www.vtechphones.com or call 1 (800) 595-

9511. In Canada, go to www.vtechcanada.com or call 1 (800) 267-7377. NOTE: Before calling for service, please review the users manual - a check of the Products controls and features may save you a service call. Except as provided by applicable law, you assume the risk of loss or damage during transit and transportation and are responsible for delivery or handling charges incurred in the transport of the Product(s) to the service location. VTech will return replaced Product under this limited warranty. Transportation, delivery or handling charges are prepaid. VTech assumes no risk for damage or loss of the Product in transit. What must you return with the Product to get warranty service?

1. Return the entire original package and contents including the Product to the VTech service location along with a description of the malfunction or difculty; and 2. Include a valid proof of purchase (sales receipt) identifying the Product purchased (Product model) and the date of purchase or receipt; and 3. Provide your name, complete and correct mailing address, and telephone number. Other limitations This warranty is the complete and exclusive agreement between you and VTech. It supersedes all other written or oral communications related to this Product. VTech provides no other warranties for this Product. The warranty exclusively describes all of VTechs responsibilities regarding the Product. There are no other express warranties. No one is authorized to make modications to this limited warranty and you should not rely on any such modication. State/Provincial Law Rights: This warranty gives you specic legal rights, and you may also have other rights, which vary from state to state or province to province. Limitations: Implied warranties, including those of tness for a particular purpose and merchantability (an unwritten warranty that the Product is t for ordinary use) are limited to one year from the date of purchase. Some states/

provinces do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you. In no event shall VTech be liable for any indirect, special, incidental, consequential, or similar damages (including, but not limited to lost prots or revenue, inability to use the Product or other associated equipment, the cost of substitute equipment, and claims by third parties) resulting from the use of this Product. Some states/provinces do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. Please retain your original sales receipt as proof of purchase.

Model: RM7868HD PU S/N: XXXXXXXXXXX WIFI MAC: xxxxxxxxxxxxxx DiSa: xxxxxxxxxxxxx UPC: 7- 3507805371 -8 FCC ID: EW780-2839-01 IC: 1135B-80283901 HVIN: 35-201949PU 23.50 0 5 7 1

. PU Model: RM7868HD PU Model: RM7868-2HD PU S/N: XXXXXXXXXXX WIFI MAC: xxxxxxxxxxxxxx DiSa: xxxxxxxxxxxxx UPC: 7- 3507805371 -8 FCC ID: EW780-2839-01 IC: 1135B-80283901 HVIN: 35-201949PU S/N: XXXXXXXXXXX WIFI MAC: xxxxxxxxxxxxxx FCC ID: EW780-2839-01 IC: 1135B-80283901 HVIN: 35-201949PU Label 23x17mm

Model: RM7768HD PU S/N: XXXXXXXXXXX WIFI MAC: xxxxxxxxxxxxxx FCC ID: EW780-2839-01 IC: 1135B-80283901 HVIN: 35-201949PU 23.50 0 5 7 1

. PU Model: RM7768HD PU Model: RM7768-2HD PU S/N: XXXXXXXXXXX WIFI MAC: xxxxxxxxxxxxxx S/N: XXXXXXXXXXX WIFI MAC: xxxxxxxxxxxxxx FCC ID: EW780-2839-01 IC: 1135B-80283901 HVIN: 35-201949PU FCC ID: EW780-2839-01 IC: 1135B-80283901 HVIN: 35-201949PU Label 23x17mm

vtech Attention: Application Examiner Re: Covered List, located at https://www.fcc.gov/supplychain/coveredlist and Report & Order 22-84 located at https://docs. fec.gov/public/attachments/DOC-389524A | pdf Applicant: VTech Telecommunications Ltd. FCC ID: EW780-2839-01 To whom it may concern, Pursuant to FCC Report & Order 22-84 section IV. Interim Freeze Order, paragraphs 264, 265, and 266, as an authorized representative of VTech Telecommunications Ltd., I attest that the equipment for which we are seeking equipment authorization through certification is not prohibited from receiving an equipment authorization; and VTech Telecommunications Ltd. is not an entity identified on the Covered List or an affiliate or subsidiary of an entity identified on the Covered List, established pursuant to 47 CFR 1.50002. I HEREBY CERTIFY THAT I am authorized to make the representations above on behalf of the company and agree to immediately notify Intertek if there is any change in the status identified above. Aull Lew Mr. Michael Tsui A Approbation Supervisor VTech Telecommunications Ltd. Form: RFT-AMER-TCB-OP-19m Revision: 1 P Date: 21 December 2022 ape at]

VTech Telecommunications Ltd May 25, 2022 To whom it may concern, Request for Permanent Confidentiality Under FCC Part 15 Certification FCC ID: EW780-2839-01 Request is hereby submitted by VTech Telecommunications Ltd. to withhold permanently from public review certain portions of the application for equipment certification for the referenced FCC identifiers. This request for confidentiality is made pursuant to 47 CFR 0.457(d) and 0.459 of the FCC Rules. In particular, the following sections of the application are to be kept permanently confidential and VTech Telecommunications Ltd. reserves the right to discern which parties can obtain access to these information:

Schematics Detailed Block diagrams Detailed Operational/Functional Description The rationale for request for confidentiality is as followings:

This information represents intellectual property of VTech Telecommunications Ltd. and it is subject to competition. We have invested considerable time and materials in research and development to produce the referenced product. Disclosure of the permanently confidential portions of this application to competitors would not only give them significant competitive advantages in developing similar products, but would also disclose successful implementation of unpublished, leading edge technology developed by us. If you have questions or need further information, please contact the undersigned. Regards, Michael Tsui Approbation Supervisor

VTech Telecommunications Ltd Appendix B1 Letter of Agency for FCC Certification Sep. 27, 2017 To whom it may concern, Letter of Agency I, an officer of VTech Telecommunications Ltd do hereby authorize Intertek Testing Services (Terry Chan/ Koo Wai Ip/ Kenneth Wong/ Jess Tang) to act on our behalf in front of the Federal Communications Commission with respect to all matters relating to certification of equipment under Part 15 and/or Part 95 of the FCC Rules until further notice. I further certify that no party (as defined in 1.2002(b) of CFR 47, 2004) to this application, including myself, is subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C., 862. Regards, Michael Tsui Approbation Supervisor