FCC ID: 2AK7ELVC01 Video Conference System HD, Conference Speaker

FCC Statement Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipemnt has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including intereference that may cause undesired operation. ISED Regulatory Compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas lincence-ex-

empt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure Compliance This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet quipement est conforme aux limites dexposition aux radiations FCC/IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. VuPoint Solutions, Inc. (USA):

710 Nogales Street, City of Industry, CA 91748 VuPoint (Europe) Company Limited:

Innovation Center, Longbridge Technology Park, Longbridge, Birmingham B31 2TS For additional info, visit our website at www.toucansolution.com 2022 VUPOINT SOLUTIONS, INC. All Rights Reserved. The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions Inc. in the United States and other countries. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Product names, logos, brands and other trademarks referred to herein are the property of their respective trademark holders. All trademarks remain the property of their respective holders, and are used only to describe the products or services being provided. These trademark holders are not aliated with VuPoint Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Incs products or services. Thank You for Purchasing CONFERENCE SPEAKER Whats in the Box Conference Speaker S100 Power Adapter USB Cable Warranty Card User Guide Getting to know your Conference Speaker S100 2 Connect S100 to your computer Plug the included USB cable into your computer and connect the end with the type-C connector to S100. Select S100 as the default microphone and speaker source. Bluetooth LED Mute LED 360 Microphones Power LED Volume up Tap to increase volume Volume down Tap to reduce volume Bluetooth Connect with new Bluetooth device Press and hold to enter Bluetooth pairing mode to connect with a new Bluetooth device Disconnect or reconnect with Bluetooth device Tap to disconnect or reconnect with a paired Bluetooth device Power On/O Press and hold to turn S100 on/o Mute Mute microphone Tap to mute or unmute microphone Voice guidance Press and hold 10s to turn voice guidance on/o Getting Started 1 Turn on S100 Plug the included power adapter into a power outlet and connect the other end to S100. Press and hold for 1 second to turn S100 on and 2 seconds to turn it o. 3 Connect S100 with a Bluetooth Device Press and hold for 2 seconds until the Bluetooth LED on S100 begins ashing. You will hear connection guidance voice prompts. Enable Bluetooth on your Bluetooth device. Select S100 from the list of available Bluetooth devices to connect. You will hear a successful connection message from S100. Tap to disconnect with connecting Bluetooth device. internal S100 Bluetooth S100 successful connection 4 Mute/Unmute Tap while calling to mute or unmute the microphone. For detailed product information, set up procedures and FAQs please visit our website: www.toucansolution.com or scan the QR code. FCC Statement Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipemnt has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including intereference that may cause undesired operation. ISED Regulatory Compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas lincence-ex-

empt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure Compliance This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet quipement est conforme aux limites dexposition aux radiations FCC/IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Thank You for Purchasing VIDEO CONFERENCE SYSTEM HD Whats in the Box VuPoint Solutions, Inc. (USA):

710 Nogales Street, City of Industry, CA 91748 VuPoint (Europe) Company Limited:

Innovation Center, Longbridge Technology Park, Longbridge, Birmingham B31 2TS For additional info, visit our website at www.toucansolution.com 2022 VUPOINT SOLUTIONS, INC. All Rights Reserved. The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions Inc. in the United States and other countries. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Product names, logos, brands and other trademarks referred to herein are the property of their respective trademark holders. All trademarks remain the property of their respective holders, and are used only to describe the products or services being provided. These trademark holders are not aliated with VuPoint Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Incs products or services. Conference Speaker S100A Display Mount Conference Camera C100 USB Cable(3m) x1 USB Cable(2m) x1 Warranty Card Power Adapter User Guide Tripod Adapter Getting to know your Video Conference System HD SC100 Bluetooth LED Mute LED 360 Microphones Power LED Volume up Tap to increase volume Volume down Tap to reduce volume Bluetooth Connect with new Bluetooth device Press and hold to enter Bluetooth pairing mode to connect with a new Bluetooth device Disconnect or reconnect with Bluetooth device Tap to disconnect or reconnect with a paired Bluetooth device Power On/O Press and hold to turn S100 on/o Mute Mute microphone Tap to mute or unmute microphone Voice guidance Press and hold 10s to turn voice guidance on/o Getting Started 1 Turn on SC100 Remove the top cover of S100A conference speaker and snap in C100 conference camera module. Plug the included power adapter into a power outlet and connect the other end to SC100 Press and hold on the top of the speaker for 1 second to turn SC100 on and 2 seconds to turn it o. 2 Connect SC100 to your computer Plug the included USB cable into your computer and connect the end with the type-C connector to SC100. Select S100A as the default microphone and speaker source. Select C100 as the default camera source. internal S100A internal C100 3 Connect SC100 with a Bluetooth Device (Audio Only) Press and hold for 2 seconds until the Bluetooth LED on S100A begins ashing. You will hear connection guidance voice prompts. Enable Bluetooth on your Bluetooth device. Select S100A from the list of available Bluetooth devices to connect. You will hear a successful connection message from S100A. Tap to disconnect with connecting Bluetooth device. successful connection Bluetooth S100A 4 Mute/Unmute Tap while calling to mute or unmute the microphone. Mount C100 on Display Snap C100 into tripod adapter and attach it to the included display mount. Mount C100 on top of the display and adjust the camera view to correct position. Plug the included USB cable into either USB port at the bottom of S100A and connect the other end with the type-C connector to C100 Select S100A and C100 as the default audio and video source on your computer For detailed product information, set up procedures and FAQs please visit our website: www.toucansolution.com or scan the QR code. FCC Statement Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipemnt has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including intereference that may cause undesired operation. ISED Regulatory Compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas lincence-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure Compliance This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet quipement est conforme aux limites dexposition aux radiations FCC/IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. Thank You for Purchasing STREAMING WEBCAM W1OO Getting to know your STREAMING WEBCAM W100 Getting Started Camera LED Lens Microphone Tripod Thread 1 Install W100 to the included display mount or tripod (not included). internal W100 2 3 4 Plug the included USB cable into your computer and connect the other end to the back of W100. Place W100 on top of the display and tilt the camera to right position. Select W100 as the default camera and microphone source on your computer. Whats in the Box Streaming Webcam W100 Display Mount USB Cable(2m) Warranty Card User Guide For detailed product information, set up procedures and FAQs please visit our website: www.toucansolution.com or scan the QR code. VuPoint Solutions, Inc. (USA):

710 Nogales Street, City of Industry, CA 91748 VuPoint (Europe) Company Limited:

Innovation Center, Longbridge Technology Park, Longbridge, Birmingham B31 2TS For additional info, visit our website at www.toucansolution.com 2022 VUPOINT SOLUTIONS, INC. All Rights Reserved. The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions Inc. in the United States and other countries. All trademarks remain the property of their respective holders, and are used only to describe the products or services being provided. These trademark holders are not aliated with VuPoint Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Incs products or services.

FCC Statement Warning: Changes or modications to this unit not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including Interference that may cause undesired operation. ISED Regulatory Compliance This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure Compliance This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. Cet quipement est conforme aux limites dexposition aux radiations FCC/IC tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps. EU Compliance VuPoint (Europe) Company Limited declares that the equipment complies with Directive 2014/53/EU. Full declaration text available at:

www.toucansolution.com/pages/certicate VuPoint Solutions, Inc. (USA):

710 Nogales Street, City of Industry, CA 91748 VuPoint (Europe) Company Limited:

Innovation Center, Longbridge Technology Park, Longbridge, Birmingham B31 2TS For additional info, visit our website at www.toucansolution.com 2022 VUPOINT SOLUTIONS, INC. All Rights Reserved. The Toucan logo and Toucan are trademarks or registered trademarks of VuPoint Solutions Inc. in the United States and other countries. The Bluetooth word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. Product names, logos, brands and other trademarks referred to herein are the property of their respective trademark holders. All trademarks remain the property of their respective holders, and are used only to describe the products or services being provided. These trademark holders are not aliated with VuPoint Solutions, Inc. They do not sponsor or endorse VuPoint Solutions, Incs products or services. Thank You for Purchasing VIDEO CONFERENCE SYSTEM HD Whats in the Box Conference Speaker S100A Display Mount Conference Camera C100 USB Cable(3m) x1 USB Cable(2m) x1 Warranty Card Power Adapter User Guide Tripod Adapter Getting to know your Video Conference System HD SC100 Bluetooth LED Mute LED 360 Microphones Power LED Volume up Tap to increase volume Volume down Tap to reduce volume Bluetooth Connect with new Bluetooth device Press and hold to enter Bluetooth pairing mode to connect with a new Bluetooth device Disconnect or reconnect with Bluetooth device Tap to disconnect or reconnect with a paired Bluetooth device Power On/O Press and hold to turn S100 on/o Mute Mute microphone Tap to mute or unmute microphone Voice guidance Press and hold 10s to turn voice guidance on/o Getting Started 1 Turn on SC100 Remove the top cover of S100A conference speaker and snap in C100 conference camera module. Plug the included power adapter into a power outlet and connect the other end to S100A Press and hold [ ] on the top of the speaker for 1 second to turn S100A on and 2 seconds to turn it o. 2 Connect SC100 to your computer Plug the included USB cable into your computer and connect the end with the type-C connector to SC100. Select S100A as the default microphone and speaker source. Select C100 as the default camera source. internal S100A internal C100 3 Connect SC100 with a Bluetooth Device (Audio Only) Press and hold [ ] for 2 seconds until the Bluetooth LED on S100A begins ashing. You will hear connection guidance voice prompts. Enable Bluetooth on your Bluetooth device. Select S100A from the list of available Bluetooth devices to connect. You will hear a successful connection message from S100A. Tap [ ] to disconnect with connecting Bluetooth device. successful connection Bluetooth S100A 4 Mute/Unmute Tap [ ] while calling to mute or unmute the microphone. Mount C100 on Display Snap C100 into tripod adapter and attach it to the included display mount. Mount C100 on top of the display and adjust the camera view to correct position. Plug the included USB cable into either USB port at the bottom of S100A and connect the other end with the type-C connector to C100 Select S100A and C100 as the default audio and video source on your computer USB3.0 Port Maximum Output Rating: DC5V/500mA For detailed product information, set up procedures and FAQs please visit our website: www.toucansolution.com or scan the QR code.

= Y Stoucan Conference Speaker S100 VUPOINT (EUROPE) CO. LTD B31 2TS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that Input:12V ==1A may cause undesired operation. Made in China FCC ID:2AK7ELVC01 Piva aC CAN ICES-3 (B)/NMB-3(B) ls: SRLNA ER ROORIRAN IC: 22430-| eect

= v

S}Toucan Conference Speaker S100A VUPOINT (EUROPE) CO. LTD B31 2TS This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received,including interference that Input:12V == 1A may cause undesired operation. Made in China FCC ID:2AK7ELVC01 PIyel | LC CAN ICES-3 (B)/NMB-3(B) ls: hens IC: 22430-| nel

VuPoint Solutions Inc. Federal Communications Commission Authorization and Evaluation Division Confidentiality Request regarding application for certification of FCC ID: 2AK7ELVC01 Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby request confidential treatment of information accompanying this application as outlined below:

Exhibit Type Block Diagram, Schematics, Operational Description, File Name Block Diagram Operation Description schematic diagram The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. Sam Lin VuPoint Solutions Inc. Rev 11/20/07

Date: 2021-12-28 VuPoint Solutions Inc. To: Federal Communications Commission 7435 Oakland Mills Road Columbia, MD FCC ID: 2AK7ELVC01 To Whom It May Concern:

This letter is to ascertain that VuPoint Solutions Inc. EUTConference Speaker, Video Conference System HD MODEL No.: S100, S100A Has been the units used for conducting FCC compliance testing, the SDoC part will be tested by EMTEK (SHENZHEN) CO., LTD. If you have any question or concerns, pls. contact us. Sam Lin VuPoint Solutions Inc.

Declaration on model difference We the undersigned hereby confirm that any of our production units bearing the following model numbers of difference is that SC100 contains S100A (similar to S100) and C100 (camera). Except above, these models are identical in circuitry and electrical, mechanical and physical construction FCC ID: 2AK7ELVC01 IC:22430-LVC01 Production name Trade name Conference Speaker Toucan Model no. S100 Video Conference System HD Toucan SC100 Confirmed by VuPoint Solutions Inc. Sam Lin VuPoint Solutions Inc. Date:

2021-12-24

VuPoint Solutions Inc. Federal Communications Commission Authorization and Evaluation Division 1435 Oakland Mills Road Columbia, MD 21046 Date: 2021-12-28 SUBJECT: FCC Application for FCC ID: 2AK7ELVC01 To Whom It May Concern:

We, the undersigned, hereby authorize Lisa Wang at EMTEK (SHENZHEN) CO., LTD. on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by EMTEK (SHENZHEN) CO., LTD. on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti- Drug Abuse Act. We, the applicant, are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sam Lin VuPoint Solutions Inc.