FCC ID: 2APNF-IWL102 LongBoxSmart(Bluetooth)WallSconcet

User Manual Smart Wall Light WSW R Part 1 How to install the Wall Light Warnings and cautions

(1) All parts must be used as indicated in these instructions. This product is designed for use only with the supplied parts and/or accessories designated for use by manufacturer. Substitution of parts or accessories not designated for use with this product by manufacturer could result in personal injury or property damage, and will void the warranty. Contact an authorized dealer or the manufacturer if any parts are damaged or missing.

(2) Make sure to cut off power before installation

(3) If there is any damage to the cord, Please cut off the power and stop using it immediately

(4) Suitable for general outdoor use.

(5) Do not submerge in water.

(6) This product is not a toy and is not designed for use by children.

(7) For safety reasons and under the terms of the warranty, the enclosed device should not be opened

(8) In case of explosion. Please keep the light away from fire and high temperature. FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . This transmitter must not be colocated or operating in conjunction with any other antenna or transmitter. Any Changes expressly or modifications not approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Specification SKU Input Voltage Input Wattage Output Wattage Color Light output Wireless type IP rating Use temperature Warranty WSW R1 120V 12-watt RGB, 4-watt of each color. W, 12-watt RGBW, W=2700K 810 Lumen at 2700K, 80+CRI BLE 5.0 (2.4G) Wet Location

-20~40C 2-year 1 / 5 User Manual Smart Wall Light WSW R Components Gasket (2pcs) Wire connector (3pcs) D F C E Junction box Screw (2pcs) Mounting Screw (2pcs) A Fixture B Back Plate Installation Step 1, Mount the fixture

(1) Secure the back plate (B) to the junction box with junction box screw (C).

(2) Do the wiring connection with wire connector (F) and following the indication of fig.1 and fig.2.

(3) Put the gasket(D) over the mounting screw(E), and fasten the lamp(A) to back plate via mounting screw.

(4) To prevent moisture/water from entering the outlet box and causing a short, use clear caulking (i.e. outdoor silicone sealant) to outline the outside of lamp canopy where it meets the wall. Leave a space at the bottom to allow moisture to escape (Fig.4). A Fixture (A) Junction box screw Mounting screw (E) Wire connector (F) Back Plate (B) Gasket Fig.1 Fig.2 Fig.3 2 / 5 User Manual Smart Wall Light WSW R Part 2 How to Pair the light to smart life app?

Important notes before starting -

(1) Ihomeyhome bridge (Sold separately) is required working with Alexa, Google assistant or do the non-local control. Bridge is not required using as a Bluetooth light.

(2) Please make sure the WiFi signal strength is strong enough for the wall light.

(3) We strongly recommend that the distance between the wall light and the bridge is kept within 65ft/20m, that the distance between the bridge and your WiFi router is kept within 65ft/20m.

(4) Before starting the paring, please make sure to turn on the Bluetooth and WiFi on your phone.

(5) The smart light only support 2.4GHz WiFi network, not 5.0GHz. Please make sure the working network is 2.4G, and your phone is connected to it. If your WiFi router supports both 2.4G and 5.0GHz, please separate the two frequency bands in the router settings, and select the 2.4GHz for connection. Step 1, Smart Life app installation. Please choose either way below to download and install the app.

(1) As per your phone system, choose the QR code to scan. iOS Android

(2) Search keyword Smart Life in Apple Store or Google Play. Step 2, Create an account on Smart life and login Note: Please keep your account and password in mind for Alexa or Google Assistant App pairing later. Step3, Add the light to smart life App

(1) Find the device of ihomeyhome bridge, see the manual of ihomeyhome bridge, Tap the bridge, click the button of Add new device.

(2) Power on the light with your own switch, if you find the light breathe in white light, Tap + button on top right corner to add devices. then find the light device and click add. If you find the light did not breathe when turn on the power. Reset the device that repeatedly turn on-off-on-off-on-off-on switch (3 times), the light breathe that mean its ready for the connection, Tap + button on top right corner to add device. To find the light device and click Add.

(3) Choose your WiFi network, enter your password, and tap the Next button. Then give a name to the light and tap the Done button. 3 / 5 User Manual Smart Wall Light WSW R Step 4, Give a name to the light

(1) A simple name is recommended for easier voice recognition with Alexa or Google Assistant.

(2) The name given to the light will be the same for voice control on Alexa or google assistant. Step 5, Control the light The named light will be shown on the app homepage. Now you can control the light (turn on/off, change colors, adjust brightness ect) with Smart life on the setting page. Step 6, How to group the wall light Note, all the light need to be the same model and already paired to smart life APP before create a group.

(1), Choose any wall light on the app, click the edit button on the top right corner, then click create group.

(2), Choose the wall lights you want to group from the device list and rename the group. Now you can control the wall lights and sync with the music, the colors will be synchronized in the group. 4 / 5 User Manual Smart Wall Light WSW R Part 3 How to control the light with Amazon Alexa?

Please make sure that your Alexa app is connected to Echo, and both work well under your WiFi network. Step 1, Log in your Alexa App, tap top left corner, and tap Skills. Step 2, Type Smart Life, find Smart Life from the search result and tap it to enable the skill. Step 3, Enter your smart life APP account and password. Tap Link Now, then tap Authorize on the next page to bind Smart life account to Alexa. Step 4, When your smart life account is bound to Alexa, Tap Discover Devices to detect the light. Step 5, When the named light is paired to Alexa from Smart Life, it will show on the device page (see the smart light example). Step 6, Now you can control the light with Alexa App on the setting page, To turn on or off the light, simply tap the bulb icon. Step 7, You can also voice control the light with Alexa by giving these commands: Alexa, Turn on Device name, Alexa, set device name to color, Alexa, set device name to number . Device name is the one you give to the light. The light is named Smart Light in this user guide. For example, Alexa, turn on smart life , Alexa, Set smart light to blue etc. Note: To control the light with Google Assistant, please continue to read Part Four. 5 / 5 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. Warning: changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

Pinging if ty an i a Qh!" ue Noy YAMS

=H i 24, LA Ho eth A UA creat 20S te et "aS 339 VOL \Z Seo Zz BUS LC SAS Ve 69 # g 0 20 BL Oe Rew cA 2 Gh 8 et Ea vi Ol Ly Bt oy 18 ry LY Ww wv OC a i An 1, AH 9 billith 4 ela 6, 0 \\\\ I, r WW ey Ov By AY nc aN, AWN AN &

C5266091_X24_Ed.1 Attestation Statements TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 The Commission adopted rules that prohibit equipment authorization for covered telecommunications equipment and video surveillance equipment produced by entities identified on the Commissions Covered List1, which is periodically updated. See the Covered List for more details. This Attestation Statement is to confirm that we follow the Section 2.911(d)(5)(i)-(ii) Applicant Company name:WAC LIGHTING CO Product Description: BG Linkable PIR solar path light Grantee code:2APNF FCC ID:2APNF-IPA302 2APNF-IWL102 Contact Name:Xiongkang Liu Address:Room No.390 Qingfeng RD, Qingxi TW Dongguan City, Guangdong Province China Telephone No: +86-769-87311200 Email:Tom.Liu@WACLighting.COM.CN i.

[WAC LIGHTING CO] (the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. The applicant must sign this certification. ii.

[WAC LIGHTING CO] (the applicant) certifies that, as of the date of the filing of the application, the applicant [ is not] identified on the Covered List as an entity producing covered equipment. The applicant must sign this certification. Date: 3/30/2023 Applicants Name:Xiongkang Liu Title:Manager Signature 1 The Commissions Covered List is published by the Public Safety and Homeland Security Bureau and posted on the Commissions website. This Covered List, which is periodically updated, identifies particular equipment, produced by particular entities, that constitutes covered equipment. https://www.fcc.gov/supplychain/coveredlist 1/1

C5266091_X10_Ed.2 WAC LIGHTING CO Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 Subject: Request for Confidentiality FCC ID: 2APNF-IWL102 To Whom It May Concern, Date: Mar 31, 2023 Pursuant to the provisions of Sections 0.457 and 0.459 of Commission's rules

(47CFR0.457, 0.459), we are requesting the Commission to withhold the following attachment(s) as confidential document from public disclosure. Exhibits ID Label/Location Attestation Statement External Photos Block Diagram Schematics Test Report Test Setup Photos Users Manual Internal Photos Parts List / Tune Up RF Exposure Info Operational Description Cover Letter(s) SDR Software / Security Info Long-Term Confidentiality No Short-Term Confidentiality NOTE 2 No No No No NOTE 1 NOTE 1 No No No No No No NOTE 1: Long-Term Confidentiality may be permitted under special conditions (See II. LONG-TERM CONFIDENTIALITY, Section 3 of KDB 726920, use last in force) NOTE 2: Short-Term Confidentiality can be requested for a maximum of 180 days from the date of the grant. Above mentioned document contains detailed system and equipment description are considered as proprietary information in operation of the equipment. The public disclosure of above documents might be harmful to our company and would give competitor an unfair advantage in the market. 1/1 C5266091_X10_Ed.2 short-term Confidentiality, the applicant requests the exhibits selected In case of above are withheld from public view for a period of ______ days from the date of the Grant of Equipment Authorization and prior to marketing. It is our understanding that all measurement test reports, FCC ID label format and correspondent during certification review process cannot be granted as confidential documents and those information will be available for public review once the grant of equipment authorization is issued. Sincerely, Name: Xiongkang Liu Date: Mar 31. 2023 Title: Manager Signature of applicant:

1/1

Model difference declaration letter Differences Description We WAC LIGHTING CO state:

Product Model Name Long Box Smart (Bluetooth) Wall Sconcet iWL102-01BK01,iWL102-**, WSW R The above product with same circuit, PCB layout, electrical parts, materials and wiring structures, the materials of decorative accessories is same, For the product appearance difference, the size is the same, but the color of the product is different (** represents different color, packaging) Signatory Date: 03-31.2023 Name: Xiongkang Liu Date: Mar 31. 2023 Title: Manager Signature of applicant:

C5266091_X8_Ed.1 WAC LIGHTING CO Letter of Authorization Company:WAC LIGHTING CO Address: No.390 Qingfeng RD, Qingxi TW Dongguan City, Guangdong Province Product Name: Long Box Smart (Bluetooth) Wall Sconcet Model Number: iWL102-01BK01,iWL102-**, WSW R FCC Identifier: 2APNF-IWL102 We authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, to act on our behalf on all matters concerning the above named equipment. Any individual within LGAI Technological Center S.A. is authorized to act on our behalf and take action on the application. We declare that authorize LGAI Technological Center S.A., Ronda de la Font del Carme, s/n, 08193 Bellaterra, Spain, information related to the approval project to the Federal Communication Commission and to discuss any issues concerning the approval application. Any and all acts carried out by LGAI Technological Center S.A. on our behalf shall have the same effect as acts of our own. is allowed to forward all Name: Xiongkang Liu Date: Mar 31. 2023 Title: Manager Signature of applicant:

1/1

US Agent for Service of Process LETTER OF ATTESTATION TO:

Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 US Agent for Service of Process:

Company Name: USA MEIHUA TRADING INC FRN: 0033406166 Contact Name: Harley Quinn Address: 5379 Pine Valley Ct Boulder CO 80301 United States Telephone No:1-312-363-9424 Email: meihua-trading-inc@foxmail,com Applicant:

Company name:WAC LIGHTING CO Product Description: BG Linkable PIR solar path light Grantee code:2APNF FCC ID:2APNF-IPA302 Contact Name:Xiongkang Liu Address:Room No.390 Qingfeng RD, Qingxi TW Dongguan City, Guangdong Province China Telephone No: +86-769-87311200 Email:Tom.Liu@WACLighting.COM.CN Company name:WAC LIGHTING CO Product Description: Long Box Smart (Bluetooth) Wall Sconcet Grantee code:2APNF FCC ID:2APNF-IWL102 Contact Name:Xiongkang Liu Address:Room No.390 Qingfeng RD, Qingxi TW Dongguan City, Guangdong Province China Telephone No: +86-769-87311200 Email:Tom.Liu@WACLighting.COM.CN

[WAC LIGHTING CO] certifies that, as of the date of this filing of the application with the TCB, [USA MEIHUA TRADING INC] is our designated US agent for service of process for the above referenced FCC ID. [WAC LIGHTING CO]

accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any commission related proceeding involving equipment. [USA MEIHUA TRADING INC] accepts, as of the date of the filing of the application, the obligation of the designated US agent for service of process for the above reference FCC ID. The US Agent for Service of Process is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. The Applicant is aware of and agrees to comply with the requirements outlined in the FCC Equipment Authorization Program, Report and Order FCC 22-84, and clause 2.911. 1/1 1/1