WWST Sensor Installation Guide WWST Sensor At a Glance Equipment Monitoring Device (EMD) Connector Gasket IP65 Connector 7 Foot Sensor Cable STEP 1 Attaching the Connector 1 After removing EMD from cardboard sleeve, attach connector to the battery-
powered node. 1 Connector Gasket 2 2 Tighten connector enough to slightly compress connector gasket. STEP 2 Installing the EMD Epoxy EMD to equipment housing with the Y axis perpendicular to rotating shaft. Connector Gasket Connector Gasket INCORRECT CORRECT 3 Be sure to note the node number for later use. 3 4 INCORRECT CORRECT STEP 3 WWST Application Form Fill out the Waites Wireless Sensor Technology Application Form. Waites Wireless Sensor Technology Application Form Node Connector # _____________________ Equipment ID _________________________ Location on Equipment (i.e. inboard beam, outboard bay, etc.) ____________________ _____________________________________ STEP 4 Powering Up 1 Con! rm that any EMD Connectors are correctly attached to the battery-powered node. Open lid of node. 5 6 2 Place two (2) D size lithium batteries in battery carriage. Note orientation of battery so that the back of battery compresses carriage springs. 3 Immediately upon installation of 2nd battery, the blue LED on the front of battery-powered node will quickly give three (3) blinks. This means the unit is in standby mode and ready to be powered up. 7 8 4 Power up unit by ! rmly pressing and releasing blue LED button on the front of node. 5 The node will ! rst perform a quality control test to ensure each EMD is correctly attached. This is communicated via six (6) blinks of the blue LED button. If the node detects a properly attached EMD at a particular node number (see p. 3 for reference), the blink is quicker than if the node does not detect a properly attached EMD. Example:
1 4
=
2 5 3 6 9 10 FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. To maintain compliance with FCCs RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna. IC Caution:
Radio Standards Specification RSS-Gen, issue 5 IC Caution:
RSS-Gen Issue 5 March 2019 "&" RSS-Gen numro 5 mars 2019
- English:
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause undesired operation of the device. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. RF exposure statement:
The equipment complies with IC Radiation exposure limit set forth for uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.
- French:
Cet appareil contient des metteurs / rcepteurs exempts de licence conformes aux RSS (RSS) d'Innovation, Sciences et Dveloppement conomique Canada. Le fonctionnement est soumis aux deux conditions suivantes:
(1) Cet appareil ne doit pas causer d'interfrences.
(2) Cet appareil doit accepter toutes les interfrences, y compris celles susceptibles de provoquer un fonctionnement indsirable de l'appareil. Tout changement ou modification non expressment approuv par la partie responsable de la conformit pourrait annuler l'autorit de l'utilisateur utiliser l'quipement. Dclaration d'exposition RF:
L'quipement est conforme la limite d'exposition aux radiations de la IC tablie pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps.