User Manual V0.4 eDVR DS412 FCC Compliance Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This Device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Caution : Any changes or modifications in construction of this device which are not expressly approved the party responsible for compliance could void the user's authority to operate the equipment. NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications, However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
-
- Connect the equipment into an outlet on a circuit different from that to which Increase the separation between the equipment and receiver. the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. CAUTION Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type. Disposal of used batteries according to the general recommendations against the environmental pollution. WEBGATE INC. 1 / 1 User Manual V0.4 eDVR DS412 Important Notice 1. When using DS412, do not put heavy monitor or others on DS412. 2. DS412 is indoor use and all the communication wirings are limited to inside of building. Therefore you should consider environmental specifications that are included in the manual. For DS412 cleaning, gently wipe the outside with a clean dry cloth. 3. Be sure to use a DC adapter that is provided by Web Gate Inc. Connecting DS412 directly to a AC current, may cause electric damages to DS412. 4. Be cautious of handling DS412. Physical shocks may harm the product. 5. DS412 is made with a metal case. When installing the camera, be sure it is attached securely to avoid any injures. Be careful to locate the camera where children cannot reach it 6. If DS412 does not operate properly, please contact the closest local WebGate distributor for after sales service. In all cases, you are prohibited to disassemble the product. If so, WebGate is not responsible for any malfunction nor service warranty. 7. Security surveillance laws may differ for each country. Therefore, please contact the local region first to avoid any surveillance law violations and to apply for authorized purposes only. WEBGATE INC. 2 / 2 eDVR DS412 User Manual V0.4 EDVR Manual Version : 0.4 Making Date : January, 28, 2003 Revision Date : February, 25, 2003 1. Install & Run 1.1. Descriptions A. Front Panel DIGITAL VIDEO RECODER AX-100L WEBGATE ALARM 1 2 3 4 MENU HELP IEEE1394 USB 1 2 3 4 5 6 7 8 9 0
+10 ENTER EXIT Remote controller Channel selection LED Function selection Direction/Replay receiver button button button
(1) Remote Controller Receiver
(2) Channel Selection Button
- To select video input channel in monitoring and playback mode
(3) LED PWR : To show power supplying status. ON means to supply power.
-
- NET : To show the status of Ethernet and communication. It blinks as many as transmitted frames per second.
- REC : To show frame recording status. It blinks as many as recording frame per second. PLAY : To show playback mode. It blinks as many as replaying frame per second.
-
- ALARM 1~4
(4) Function selection button
-
SEQ : To show with converting all connected video channels
- MULTI : To show multi channels (4-9-16-13 divided screen)
-
- ZOOM : To show expanded image via one channel mode SELECT : To select video channel for PTZ control WEBGATE INC. 3 / 3 User Manual V0.4 eDVR DS412
-
SEARCH : To search the recorded image in Playback mode
(5) Direction/Replaying Button
- MENU : To set PTZ and configuration menu
- ENTER : To confirm the selected menu
- HELP :
- EXIT : To exit form the selected menu
- Arrow key : Replay function or menu moving function B. Rear Panel 1.RXD 2.TXD 3.GND 4.R+
5.R-
6.T+
7.T-
8.GND COM2/RS232 AUDIO MIC VIDEO OUTPUT MONITOR VIDEO INPUT Ch1 Ch2 COM1 SENSOR IN RS232 RS422/485 S1 S1 S1 S1 1 2 3 4 5 6 7 8 ALARM OUT O1 O2 O3 04
+ - + - + - + - + - + - + - + -
LINE VCR Ch3 Ch4 POWER ON ETHERNET 10/100 REMOTE CONTROL VIDEO INPUT HI-Z NTSC ON USB1 IEEE1394 DC12V 3.5A GND 1 2 3 4 75ohm PAL OFF 1 2 USB2 Serial port &
Audio input DIO Video output Video input Ethernet Power
(1) Serial Port & DIO Serial : RS232 9Pin D-Sub Connector & RS232/422/485 terminal block Sensor In : 4 sensor inputs
-
-
- Alarm Out : 4 Alarm Relay outputs
(2) Audio In/Output
-
1 audio input & 1 output
(3) Video Output
-
1 monitor output & 1 VCR output
(4) Video Input
-
4 video inputs
(5) Ethernet
(6) Power WEBGATE INC. 4 / 4 User Manual V0.4 eDVR DS412 1.2. Connect Device A. Connect Video B. Connect Monitor C. Connect Ethernet D. Connect Audio E. Connect Power & Run 2. Monitor It is to monitor real time image. Ch. 1~4 are for analogue image input via BNC cable, and Ch. 5~16 are for digital image input of network camera via network. A. View basic screen (quad-split)
(1) Supply power.
(2) Power LED is on, and DVR starts booting.
(3) After booting, basic screen (quad-split) shows. If user password is set, a dialogue for entering password will be indicated. B. View full screen
(1) Press the button of channel that user to view from multi screen wants
(4/9/16/13).
(2) When selecting one between channel 10 and 16, press the [+10] button at first then the other number.
(3) Screen changes into 1 channel full screen, and the related channel shows.
(4) If pressing the [MULTI] button, full screen moves to the previous multi screen. C
. View multi screen WEBGATE INC. 5 / 5 User Manual V0.4 eDVR DS412
(1) Press the [MULTI] button for viewing several channels simultaneously.
(2) Whenever pressing the [MULTI] button, 4-9-16-13 split screens are chang ed in due order.
(3) In quad-split mode, images of channels 1 to 4 show. Channels 1 to 9 in 9-split mode, chann els 1 to 16 in 16-split mode, and channels 1 to 12 in 13-split mode. D
. View all channels with automatic converting
(1) All channels can be viewed in due orde
(2) Press the [SEQ] button from current multi screen (except 16/13-split screen).
(3) Show [SEQ] mode in the right of screen and sequential images as much as the r automatically with using the [SEQ] button. configured Auto SW Interval value. If connected channels
(4)
(5) Set Auto SW Interval value in menu. Default value is 3 seconds.
(6) To shut down [SEQ] function, press the [SEQ] button. are smaller than number of current split screen, SEQ function will not run. E
. View an alarm triggered channel
(1) Set Alarm Pop-up Screen function in menu.
(2) When alarm is triggered, the related channel po ps up automatically.
(3) According to alarm triggered channel number, a split screen shows a utomatically. For example, if alarm triggered channels are three, the images show in quad-split screen. Show type of alarm trigger in the left of screen.
(4)
. View extended image F
(1) Extended image
(2) Press the [ZOOM] button.
(3) Extended image shows by t wice size.
(4) Default place of extended image is on can be viewed with [ZOOM] button from Full screen mode. the center of screen. And it can move each 10th step to left and right and 4th to up and down. To move it, use the [Arrow] button
(5)
.
(6) If repress the [ZOOM] button, the fu nction is cancelled. View with connecting PTZ G
(1) When PTZ controller is connected to eDVR and Serial Conf. is set in menu, PTZ can be controlled. Press the [S ELECT] button in monitor mode.
(2)
(3) Channel selection menu shows.
(4) Select a channel with [Arrow] bu tton. WEBGATE INC. 6 / 6 User Manual V0.4 eDVR DS412
(5) Press the [MENU] button.
(6) PTZ menu (PAN/TILT, ZOOM/FOCUS, Preset, Preset Save) shows.
(7) Press the [ENTER] button after selecting one.
(8) When selecting PAN/TILT or ZOOM/FOCU S, [UP/DOWN] arrow key is for TILT/FOCUS and [LEFT/RIGHT] arrow key for PAN/ZOOM. When selecting Preset, a dialogue for selecting stored preset
(9) shows.
(10) When selecting Preset Save, a dialogue for storing current point as p reset shows. H
. View network cameras image
(1) Channels 5 to 16 are for input of network cameras (WebEye Series, I-Rec Series).
(2) eDVR should be connected to Ethernet and the related channel be set in MENU. 3
. Playback It is to replay A recorded images via full screen or quad split screen. Playback via basic screen (full screen)
(1) Press the Play [] button.
(2) Play [] button is to replay as 1x.
(3) The recorded image of channel 1 be B
. Playback via split screen fore 1 minute 45 seconds is displayed.
(1) Press the [MULTI] button from
(2) Channels 1 to 4 shows in quad-split screen.
(3) To move into basic screen playback, press th basic screen playback mode. e related channel number. C
. Playback with extending
(1) Press the [ZOOM] button from
(2) Extended image shows by twice size.
(3) Default place of extended image is on basic screen playback mode. the center of screen. And it can move each 10th step to left and right and 4th to up and down. To move it, use the [Arrow] button
(4)
.
(5) If repress the [ZOOM] button, the fu nction is cancelled. D
. Various playback modes
(1) (PLAY) : To rep lay as 1x.
(2) (STOP) : To stop replaying WEBGATE INC. 7 / 7 User Manual V0.4 eDVR DS412
(3) (PAUSE) : To pause replaying
(4) (FAST FORWARD) : Whenev er pressing the button, replaying speed increases gradually
(5)
(6)
(7)
(x1, x2, x4, x8, x16)
(FAST REWIN gradually (x1, x2, x4, x8, x16) STEP FORWARD : When pres pause status, image is replayed frame by frame. STEP REWIND : When pressing [, FAST R replayed frame by frame. D) : Whenever pressing the button, reverse replaying speed increases sing [, Replay] or [, FAST FORWARD] button from EWIND] button from pause status, image is
. Search 4 It is to sea rch any image in playback mode.
(1) Press the [SEARCH] button in playback mode.
(2) Search something with entering date/time or sele
(3) Searching channel is current playback channel.
(4) Press the [ENTER] button after entering the rela
(5) The searched image is replayed.
(6) To exit from search mode, press t he [EXIT] button. cting log in log browser. ted value or selecting log. nel and recording schedule with using [MENU] button. There are total seven menus 5
. Setting menu It is to set chan
(Camera, Normal Rec., Alarm Rec., Relay, Monitor, System, Utility) A
. Descriptions
(1) Press th
(2) Enter Admin password, if it is set.
(3) Main menu can be selected with left e [Menu] button of front panel.
/right button. To move to the sub menu, press the [Enter]
button. To move t o upper menu, press the [Exit] button.
(4)
(5) A changed value is applied instantly.
(6) Status bar indicates value of selected m enu or help. B
. Dialogue for entering word
(1) When setting value is a word, t
(2) To set a word, use direction arrow keys and number keys 0 to 9". he related dialogue box is indicated. WEBGATE INC. 8 / 8 User Manual V0.4 eDVR DS412
(3) The matching point between horizontal and vertical bar is selecting value.
(4) Or enter the related numbers in order of horizontal/vertical. (For example, i n order to select N, press [4] and [3] button.) Press the [ENTER] button in ord
(5)
(6) After setting all values, press the [Exit] button. er to confirm the selected value. Camera setting C
(1) Analogue Video ideo input are same like picture above. If pressing [Enter] key after selecting a channel, user can move to the sub
(Ch1 Ch4) Input
- All setting menus for analogue v
-
- Name: If pressing [Enter] key, the related dialogue box is indicated.
- Activity: Set On/Off with using button or button after p ressing [Enter] key.
- Type: It only shows input video signal(NTSC/PAL). To set it, use dip switch on the rear o
- Color: Set Color/Mono with using button or button after pressing [Enter] key.
- Gain/Bright/Contrast; Set the value between 9 and +9 with using button or butto
-menu. n f DVR. after pressing [Enter] key. PTZ Port: Set the value with
-
- Address: If pressing [Enter] key, the related dialogue box is indicated. using button or button after pressing [Enter] key.
(2) Network Camera Video (Ch5 Ch16) Input
* There are Login menu and Network menu. 1) Login menu
- Name: If pressing [Enter] key, the related dialogue box is indicated.
- Activity: Set On/Off with using button or button after p ressing [Enter] key.
- Access Token: If the related network camera is encrypted, the same value that is set in its admin word should be entered. Default value
-
menu should be configured. Default value is NULL. User ID/Password: The related network cameras ID/Pass is guest/guest. Type: Set WebEy e/I-Rec with using button or button after pressing [Enter] key.
-
- CH: Set one between Ch1 and Ch6. IP Address(URL): If pressing [Enter]
-
key, the related dialogue box is indicated. Port: If pressing [Enter] key, the related dialogue box is indicated. The de
-
different according to camera type; 8080 in WebEye and 8001 in i-Rec. fault values are WEBGATE INC. 9 / 9 User Manual V0.4 eDVR DS412 2) Network menu
- Refresh: If selecting it, all local cameras are listed up. If using this menu, it is needless to enter each local cameras IP address manually in Login menu. D. Normal Recording
* There are four types (Weekday Day/Weekday Night/Weekend Day/Weekend Night).
- Normal Recording: There are five conditions
(No Rec./Low/Standard/High/Custom). All conditions except Custom operate together with Frame Rate and Quality automatically; 3fps/Q1 in Low, 10fps/Q3 in Standard, and 20fps/Q5 in High. When setting Custom, Frame Rate and Quality can be set separately. Special Time Recording: There are five conditions
(No Rec./Low/Standard/High/Schedule). It can be set in System menu.
-
- Alarm Recording: Set On/Off with using button or button after pressing [Enter] key. E. Alarm Recording
* Among these menus, some menu may not be activated. Namely, setting menus are different according to camera type(analogue camera/network camera). In addition to that, WebEye series doesnt support Alarm Recording currently. WebEye can support this menu after upgrading Firmware in July.
-
IP Cam Event: It is only for I-Rec series(Ch.5 ~ Ch.16) currently. If setting as On after registering I-Rec series, its related data are recorded according to setting menu in cameras admin menu.
- MD/S1/S2/S3/S4: It is only for analogue cameras(Ch.1 ~ Ch.4). Be carious that DVR is set on the base of NO(Normal Open) type sensor.
- Alarm Recording: There are five conditions.
(No Rec./Low/Standard/High/Custom) All conditions except Custom operate together with Frame Rate and Quality automatically. When setting Custom, Frame Rate and Quality can be set separately. Pre/Post Alarm: Maximal 10 seconds can be set.
-
WEBGATE INC. 10 / 10 User Manual V0.4 eDVR DS412 F. Relay
* There are four types(Weekday Day/Weekday Night/Weekend Day/Weekend Night). Setup: It can be set from Relay1 to Relay4. It is for sending digital output signal in case of alarm triggered event(MD or Sensor). Special Time: It is for setting in Special Time zone.
-
-
G. Monitor
- Auto Sequence: It is for setting auto sequence cycle in monitoring mode. Its maximal value is 60 seconds.
- Alarm Pop-up: It is for setting automatic video pop-up, when alarm is triggered.
-
Pop-up Hold: It is for setting pop-up images duration among 5/6/7/8/9/10 seconds/Keep. H. System 1) Audio
- Recording: It is to set whether audio is recorded or not.
- Level: It can be set between 7 and +8.
-
- Video Link: It is to link with replayed video channel.
+20dB: It is for amplifying audio input signal against low input level. 2) Time
- Date/Time: It is to set Date and Time.
- Date Format: It is set one between MM/DD/YYYY and YYYY/ MM/DD.
- Weekday Start/End: It is to set a range of Weekday. The other range will be Weekend.
- Day Start/End: It is to set a range of Day. The other range will be Night.
- Daylight Saving: It is to set daylight saving. If it set as On, time will be changed automatically in related period.
- Time Zone: It is to set time zone.
-
Set time: To set a value, another menu has only to exit from the related menu. But for setting time, user should certainly press this button. 3) Special Time
- It is to set maximal four zones as Special Time. WEBGATE INC. 11 / 11 User Manual V0.4 eDVR DS412 4) Security
- User Password: It is to set Users Password only for monitoring and playback.
- Admin Password: It is to set Admins Password for all controlling.
- Remote Setup: If setting as Enable, user can set DVR with specific S/W in remote site via network.
- Remote DIO: It is to set DIO menu in remote site. 5) Disk Setup
- Auto Del. Normal: When HDD is full of recorded data, they can be deleted automatically except alarm-triggered data.
- Auto Del. Alarm: If setting it, alarm-triggered data will be also deleted in case of being full.
- Alarm Partition: DVR recognizes all connected HDDs as one. It is to set percentage of HDDs for alarm recording range within HDDs total sizes.
- Backup Reminder: It is to set backup information showing according to EveryDay, EveryWeek, or EveryMonth.
- Day/Time: According to setting values of Backup Reminder, setting ranges are indicated differently. 6) Network 6)-1: Network
- Type: It is to set connected network line(Ethernet/xDSL).
- DHCP: It is to set DHCP using or not.
- Network information setting: It is to set IP address, Netmask, Gateway, or DNS servers IP address. 6)-2 xDSL
- User ID/Password: When DVR is connected to xDSL, access ID and Password should be entered.
- WRS Interval/URL/Group: It is to set server registering interval, servers URL, or configured group ID.
- Status: It shows xDSLs accessing status.
* Currently(25, February), eDVR supports only Ethernet, not xDSL. After upgrading xDSL function, WebGate will let you know it instantly. WEBGATE INC. 12 / 12 User Manual V0.4 6)-3 Server eDVR DS412
- Monitoring Port/Playback Port: DVR use 8001 port as Monitoring port and 8105 port as Playback port. When selecting one for changing, the related dialogue box is indicated.
- Firewall/Port: When using Firewall, set is as Yes and enter its port. 7) Serial Setup
* There are two RS232 menus (One is for external device via DB-9 pin, and the other is for PTZ setting) and RS 422/485 menu.
- Device: It is to set a connected external device.
- Baud rate/Parity/Stop bit/Data bit: Each value should be set normally according to a connected external device. 8) Miscellaneous
- Remote Control ID: Total sixteen remote control IDs can be set. So with this seeing, maximal sixteen DVRs can be controlled with one remote controller.
- DVR ID: It shows in specific DVR manager S/W in order to manage several DVRs easily.
-
Factory Setting: It is for factory setting. I. Utility 1) Disk Manager
- A connected HDD is detected automatically.
- Action: Set one among Add/Remove/Format/Confirm Removed.
-
- Type: There are several kinds of indicating words. Select Disk: It is to select a setting Disk.
[?] : It shows a detected HDDs status before formatting
[*] : It shows a added HDDs status before formatting
[R] : It shows a using HDDs status after formatting
[X] : It shows a not-detected HDDs status that is used previously. 2) Disk Backup
-
-
Start Date/End Date: It is to set backup range. Select Disk: The connected backup HDD is detected automatically. At first, backup HDD should be added and formatted in Disk Manager menu. WEBGATE INC. 13 / 13