Module Pin Name and Description:
Pin #
Pin Name Pin Description 1 2 3 4 5 6 7 8 9 10 GND VCC Ground Power supply DOUT / DIO-
PA9 DIN / DIO-
PA10 UART Data Out / GPIO / I2C SCL / PWM UART Data In / GPIO / I2C SDA / PWM DIO-PC13 GPIO / RTC Alarm
*RESET Module Reset RX Signal Strength Indicator / GPIO RSSI PWM/DIO-
PB4 DIO-PB10 Pulse Width Modulator / GPIO
[reserved]
Do not connect
*DTR /
SLEEP_RQ /
DIO-PB0 Pin Sleep Control Line / GPIO / A2D input /
PWM 11 12 13 14 15 16 17 18 19 20 GND Ground
*SPI_ATTN /
*BOOTMODE
, DIO-PF11 Select boot source / GPIO Can boot from UART, FLASH, RAM, I2C, or USB GND Ground SPI_CLK /
DIO-PA5 Serial Peripheral Interface Clock / GPIO / A2D input / PWM
*SPI_SSEL /
DIO-PA4 Serial Peripheral Interface not Select / GPIO /
A2D input / PWM SPI_MOSI /
DIO-PA7 Serial Peripheral Interface Data In / GPIO /
A2D input / PWM SPI_MISO /
DIO-PA6 Serial Peripheral Interface Data In / GPIO /
A2D input / PWM
[reserved]
Do not connect SWCLK; used in production to program uC
[reserved]
Do not connect / GPIO
[reserved]
Do not connect PWM / GPIO 21
[reserved]
Do not connect SWDIO; used in production to program uC 22 23 24 25 26 27 28 GND Ground
[reserved]
Do not connect GPIO DIO-PC14 GPIO
*CTS / DIO-
PA11 Clear to Send Flow Control / GPIO / PWM /
CAN / USB ON / *SLEEP
/ DIO-PA15 Module Status Indicator / GPIO / PWM /
UART2 RX AD9 A2D input / PWM / GPIO DIO-PB3 GPIO / PWM 29 30 31 32 33 34 35 36 37 38 39 40
*RTS / DIO-
PA12 Request to Send Flow Control / GPIO / PWM /
CAN / USB AD3 / DIO-
PA3 AD2 / DIO-
PA2 AD1 / DIO-
PA1 AD0 / DIO-
PA0 Attn GND
-
Analog Input / GPIO / PWM / UART2 RX Analog Input / GPIO / PWM / UART2 TX Analog Input / GPIO / PWM / UART2 RTS Analog Input / GPIO / PWM / UART2 CTS Radio Module asserts this when it requires attention Ground Not connected
[reserved]
Do not connect CAN_TX CAN TX/ I2C SDA / PWM / GPIO / IR_OUT CAN_RX CAN RX / I2C SCL / PWM / GPIO VBAT Voltage supply for small amount of RAM and RTC (intended to be connected to a battery) Host PCB mating footprint:
Antenna Type:
Antenna A: Dipole antenna Antenna B: Matel antenna or Spiral antenna The two antenna can not work at the same time. external antenna is not allowed and it may subject to additional testing and certification. Warnings:
FCC Warning: Changes or modifications to this unit not expressly approved compliance could void the users authority to operate the equipment. by the party responsible for limits for a Class B digital device, harmful interference in a residential installation. This equipment generates, occur in a particular installation. If this equipment does cause harmful interference in accordance with the instructions, may cause communications. However, there is no guarantee that interference will Note: This equipment has been tested and found to comply with the pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against radio frequency energy and, if not installed and used harmful interference to radio not television reception, which can be determined by turning the equipment encouraged to try to correct the interference by Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the connected. Consult the dealer or an experienced radio/TV technician for help. of the following measures:
off and on, the user is one or more to radio or receiver is uses and can radiate This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation. Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
"This equipment & Host complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment & Host should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body."
This module is designed to comply with the FCC statement, FCC ID is: 2AEOD-1400004B00101. IC is 20139-1400004B001 The host system using this module, should have label in a visible area indicated the following texts:
"Contains FCC ID: 2AEOD-1400004B00101, IC: 20139-1400004B001". This LMA is tested and approved as standalone configuration, additional evaluation may be required for any system integrated this radio module this module and its antenna should not be installed and operated with other radio simultaneously IC Caution. RSS-Gen Issue 4 Nov 2014"&"CNR-Gen 4e ditionNovembre 2014:
English:
-
This device complies with Industry Canada licence-exempt RSS standard(s). following two conditions: (1) This device may not any interference, including Operation is subject to the cause interference, and (2) This device must accept interference that may cause undesired operation of the device. French:
-
Le presentappareilest conforme aux CNR d'Industrie Canada applicables aux licence. L'exploitationestautorise aux deux
(1)
(2) l'utilisateur de l'appareildoit accepter tout brouillageradiolectriquesubi, susceptible d'encompromettre le fonctionnement. l'appareil ne doit pas produire de brouillage, et conditions suivantes:
appareils radio exempts de mmesi le brouillageest