all | frequencies |
|
|
|
|
exhibits | applications |
---|---|---|---|---|---|---|---|
manual | photos | label |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User-Manual | Users Manual | 4.66 MiB | January 26 2021 / July 25 2021 | delayed release | ||
1 2 |
|
Int photos | Internal Photos | 837.13 KiB | January 26 2021 / July 25 2021 | delayed release | ||
1 2 |
|
External Photos | External Photos | 287.66 KiB | January 26 2021 / July 25 2021 | delayed release | ||
1 2 |
|
label | ID Label/Location Info | 3.54 MiB | January 26 2021 | |||
1 2 |
|
Agent Authorization | Cover Letter(s) | 285.82 KiB | January 26 2021 | |||
1 2 | BOM | Parts List/Tune Up Info | January 26 2021 | confidential | ||||
1 2 | Block Diagram | Block Diagram | January 26 2021 | confidential | ||||
1 2 |
|
Declaration of Compliance | Cover Letter(s) | 213.42 KiB | January 26 2021 | |||
1 2 |
|
MPE | RF Exposure Info | 66.28 KiB | January 26 2021 | |||
1 2 | Operational Description | Operational Description | January 26 2021 | confidential | ||||
1 2 | Schematic | Schematics | January 26 2021 | confidential | ||||
1 2 |
|
Test Photos | Test Setup Photos | 383.48 KiB | January 26 2021 / July 25 2021 | delayed release | ||
1 2 |
|
attestation letter | Attestation Statements | 281.55 KiB | January 26 2021 | |||
1 2 |
|
request for confidentiality Part 20 | Cover Letter(s) | 331.93 KiB | January 26 2021 | |||
1 2 |
|
request for confidentiality Part | Cover Letter(s) | 333.19 KiB | January 26 2021 | |||
1 2 |
|
test report | Test Report | 1.49 MiB | January 26 2021 |
1 2 | User-Manual | Users Manual | 4.66 MiB | January 26 2021 / July 25 2021 | delayed release |
CS40-734834-00D-A0 Product Manual
5689
April 2020, Rev A
CS40-734834-00D-A0 2.5W Public Safety
Signal Booster
Users Guide
P
R
O
D
U
C
T
M
A
N
U
A
L
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 1 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
DISCLAIMER
All information and statements contained herein are accurate to the best of Westell Technologies knowledge.
Westell makes no warranty with respect there to, including without limitation any results that may be obtained
from the products described herein or the infringement by such products of any property rights of any persons.
Use or application of such information or statements is at the users’ sole risk, without any liability on the part of
Westell. Nothing herein shall be construed as license or recommendation for use, which infringes upon any
propriety rights of any person. Product material and specifications are subject to change without notice. Westell
standard terms of sale and the specific terms of any particular sale apply.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 2 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Table of Contents
TABLE OF FIGURES ..................................................................................................................... 6
LIST OF TABLES ........................................................................................................................... 7
Preface 8
Purpose 8
Scope 8
Audience................................................................................................................................................................ 8
Document Organization ......................................................................................................................................... 8
References ........................................................................................................................................................... 10
Document Conventions ........................................................................................................................................ 10
Safety Notices ...................................................................................................................................................... 11
Technical Support ................................................................................................................................................ 11
Acronyms and Abbreviations ............................................................................................................................... 11
Copyright and Trademark Acknowledgements ..................................................................................................... 11
1 GENERAL INFORMATION ...................................................................................................... 12
1.1 Document Purpose and Intended Users ......................................................................................................... 12
1.2 Application ..................................................................................................................................................... 12
1.3 Product Registration Information ................................................................................................................... 12
1.4 Safety Guidelines ........................................................................................................................................... 14
1.5 Important Safety Information ........................................................................................................................ 15
1.6 FCC Part 90 Signal Boosters ............................................................................................................................ 15
▣ FCC Part 15 Class A .................................................................................................................................... 17
1.7 FCC Contact Information: ............................................................................................................................... 18
2 PRODUCT OVERVIEW ............................................................................................................ 19
2.1 Product Information ......................................................................................................................... 19
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 3 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
2.2 Product Features ............................................................................................................................................ 20
2.3 Included Accessories ...................................................................................................................................... 21
2.4 Optional Accessories ...................................................................................................................................... 22
3 PRODUCT SPECIFICATION ..................................................................................................... 23
3.1 RF Specifications ............................................................................................................................................ 23
3.2 Power Specification ........................................................................................................................................ 25
3.3 Mechanical Specification ................................................................................................................................ 25
3.4 Environmental Specification ........................................................................................................................... 26
3.5 GUI Items ....................................................................................................................................................... 26
3.6 Alarm Status .................................................................................................................................................. 27
3.7 Alarm Relay .................................................................................................................................................... 28
4 PRODUCT APPEARANCE ........................................................................................................ 30
4.1 External Configuration ................................................................................................................................... 30
5 INSTALLATION GUIDELINES ................................................................................................... 31
5.1 Important Installation Guidelines ................................................................................................................... 31
5.2 Donor Antenna Installation Guidelines .......................................................................................................... 32
5.3 Indoor Antenna Installation Guidelines .......................................................................................................... 33
5.4 Mounting the Signal Booster .......................................................................................................................... 34
5.5 Verifying the Physical System Setup ............................................................................................................... 35
5.6 Controlling the Signal Booster ........................................................................................................................ 35
5.7 Connecting to the Alarm Relay Panel ............................................................................................................. 36
5.8 Connecting the Power Cable .......................................................................................................................... 39
5.9 Connecting the Battery Back-up Cable ........................................................................................................... 41
5.10 BBU Specification ......................................................................................................................................... 41
6 SYSTEM OPERATION .................................................................................................. 42
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 4 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
6.1 Operating the Program ................................................................................................................................... 42
6.2 Web GUI System Status .................................................................................................................................. 43
6.3 Alarm Page ..................................................................................................................................................... 43
6.4 RF Configuration ............................................................................................................................................ 45
6.5 Annunciator Test ............................................................................................................................................ 47
7 SYSTEM SOFTWARE UPGRADE .............................................................................................. 48
7.1 Upgrading the System Software ..................................................................................................................... 48
7.3 Network (WAN) Setting .................................................................................................................................. 49
APPENDIX A
IMPORTANT PRODUCT INFORMATION ............................................................ 50
A.1 Registration Number ..................................................................................................................................... 50
A.2 ETL 50
A.3 Configuration LIST .......................................................................................................................................... 50
APPENDIX C UL2524 INSTALLATION GUIDELINES .................................................................. 52
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 5 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
TABLE OF FIGURES
Figure 1-1: Product Registration……..................................................................................................... 12
Figure 4-1: External Product Configuration.......................................................................................... 27
Figure 5-1: Repeater Mounting Bracket Mounted on Repeater Rear.................................................. 30
Figure 5-2A: Ethernet Cable................................................................................................................. 31
Figure 5-2B: Ethernet Connectors........................................................................................................ 32
Figure 5-3: Stripped Cable Conductors……........................................................................................... 32
Figure 5-4: Alarm Relay 18-wire Gland Connector M6110 .................................................................. 33
Figure 5-5: Alarm Relay Cable Connected to Repeater........................................................................ 33
Figure 5-6: Remove the Power Connector Cap.................................................................................... 35
Figure 5-7: Connector Keys.................................................................................................................. 36
Figure 5-8: Power Cable Connected to Repeater……........................................................................... 36
Figure 5-9: Power Cable Connected to Repeater................................................................................. 37
Figure 5-10: Battery Cable Connected to Repeater............................................................................. 38
Figure 6-1: Network Connection Set-up .............................................................................................. 39
Figure 6-2: Destination Directory…….…………………............................................................................... 40
Figure 6-3: Software Installation…………………....................................................................................... 40
Figure 6-4: CS40-734834-00D-A0 GUI Log-
In……………….......................................................................................... 41
Figure 6-5: Status Mode………………………............................................................................................... 42
Figure 6-6: Control Mode………............................................................................................................. 47
Figure 7-1: Firmware Upgrade Progress Window showing File Open tab ........................................... 52
Figure 7-2: Firmware Version Check….................................................................................................. 53
Figure 7-3: System Upgrade Status...................................................................................................... 53
Figure 7-4: IP Settings........................................................................................................................... 54
Figure 7-5: IP Change WIndow............................................................................................................. 54
Figure 7-6: Static IP Address….………………………..................................................................................... 55
Figure 7-7: DHCP IP Address….............................................................................................................. 55
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 6 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
LIST OF TABLES
Table P-1: Document Conventions...................................................................................................... 10
Table 2-1: Included Accessories........................................................................................................... 17
Table 2-2: Optional Accessories .......................................................................................................... 18
Table 3-1: RF Specifications................................................................................................................. 19
Table 3-2: Power Specifications........................................................................................................... 20
Table 3-3: Mechanical Specifications................................................................................................... 21
Table 3-4: Environmental Specifications.............................................................................................. 22
Table 3-5: GUI Items............................................................................................................................. 22
Table 3-6: Alarm Status........................................................................................................................ 24
Table 3-7: Alarm Relay......................................................................................................................... 25
Table 5-1: Alarm Relay Connections.................................................................................................... 34
Table B-1: Acronyms and Abbreviations.............................................................................................. 57
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 7 of 52
April 2020, Rev A
CS40-734834-00D-A0 Product Manual
Preface
This Preface includes the following:
Purpose
Scope
Audience
Document Organization
References
Document Conventions
Safety Notices
Technical Support
Acronyms and Abbreviations
Copyright and Trademark Acknowledgements
Purpose
This manual contains information and procedures for the operation of the Westell CS40-734834-00D-
A0 Public Safety Signal Booster.
Changes that occur after the publishing date may be incorporated by a complete manual revision or
as additions.
Scope
Reference this manual when there is a need to add enhanced signal capability to a new or existing
system, to monitor a system, make maintenance adjustments, or address alarms.
Audience
This manual is intended for installers and users who are familiar with similar types of equipment.
Document Organization
This manual includes the following chapters:
•
•
•
Chapter 1: General Information – Outlines the document purpose and intended users,
application, product registration, safety guidelines, disclaimer and FCC Part 90, FCC Warning
Labels.
Chapter 2: Product Overview – Provides product information, describes product features
and lists accessories.
Chapter 3: Product Specification – Provides tables containing RF, power, mechanical and
environmental specifications. Also provides information about GUI items, alarm status and
alarm relay.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 8 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
•
•
•
•
Chapter 4: Product Appearance – Provides physical specifications, photographs and
information about the external and internal Signal Booster configuration.
Chapter 5: Installation Guidelines – Lists guidelines for installing the Signal Booster and
antennas.
Chapter 6: Software Installation – Outlines the steps required to install the software.
Chapter 7: System Operation – Describes product operation, including how to open the
communication port and describes the functions in the Status and Control pages.
• Appendix A: Important Product Information – Provides the product registration number
and internal power supply information.
• Appendix B: Acronyms and Abbreviations – A table of acronyms and abbreviations and
definitions for each.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 9 of 52
April 2020, Rev A
CS40-734834-00D-A0 Product Manual
References
•
FCC Part 90
Document Conventions
Table P-1 lists the conventions used throughout this document.
Table P-1: Document Conventions
Convention
Description
DANGER!
Description of an imminent hazard that, if not avoided, may result in severe personal
injury or death. Before you work on equipment, be aware of the hazards involved with
electrical and RF circuitry and be familiar with standard practices for preventing
accidents.
WARNING!
Description of an imminent hazard that, if not avoided, may result in personal injury or
serious equipment damage.
CAUTION
Description of a conditions or practice that could cause damage to equipment or
property. Communicates information that is crucial to preventing loss of data or damage
to hardware or software, and actions that could result in equipment failure.
IMPORTANT
Additional important information that the user must be aware of, but is not related to a
hazard.
Additional information that is beneficial for the user to know, but is not related to a
hazard.
Bold text indicates an action or provides emphasis.
Instructs the user to press the primary (typically left) mouse button while the pointer is
over the specified location.
Right-click
Instructs the user to press the secondary (typically right) mouse button while the pointer
is over the specified location.
Double-click
Instructs the user to press the primary (typically left) mouse button twice, rapidly, while
the pointer is over the specified location.
Instructs the user to perform a selection on the screen by clicking an active object.
Instructs the user to type text using the keyboard.
Indicates a level in a menu. For example, Start>Programs prompts the user to click on
Start, then locate and click Programs under the Start menu.
NOTE
Bold
Click
Select
Enter
>
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 10 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Safety Notices
This general safety information applies to both operating and service personnel. Specific warnings and
cautions are located in other parts of this manual where they apply and may not appear in this
summary. Failure to comply with these precautions or specific warnings elsewhere in the manual
violates the safety standards of design, manufacture, and intended use of equipment.
Westell assumes no liability for the customer’s or user’s failure to comply with these requirements:
•
•
Explosive atmospheres - To avoid explosion or fire, do not operate this product in the
presence of flammable gases or fumes.
Lightning danger - Do not install or make adjustments to this unit during an electrical storm.
WARNING!
Changes and Modifications not expressly approved by Westell can void your
authority to operate this equipment under Federal Communications Commission’s
rules.
Technical Support
If you suspect a malfunction with this product or have a technical question, call your dealer or the
Westell Support Line at: (603) 626-6677, Toll Free (USA) 1-800-377-8766, press option 2, and then
option 3. Westell Support can also be reached via email at Support@westell.com.
Acronyms and Abbreviations
Refer to Appendix B for definitions of the acronyms and abbreviations used in this manual.
Copyright and Trademark Acknowledgements
The following products are referred to in this manual:
is a registered trademark of Westell Technologies, Inc.
•
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 11 of 52
CS40-734834-00D-A0 Product Manual
1 General Information
April 2020, Rev A
1.1 Document Purpose and Intended Users
The purpose of this document is to provide a step-by-step procedure to help experienced technicians or
engineers install and commission an in-building Passive Wireless Distributed Antenna System (DAS)
using Westell’s CS40-734834-00D-A0 2.5W Public Safety Signal Booster. Follow the instructions in this
guide to minimize risks associated with modifying a live system and preclude service interruptions. This
document assumes the technician or engineer understands the basic principles and functionality
involved with an RF Signal Booster and in-building wireless systems. This guide has been written to
address the practical concerns of the installer.
1.2 Application
Use this guide whenever there is a need to add enhanced signal capability to an existing system or
when a Signal Booster is included in a new installation.
1.3 Product Registration Information
Username and Password are provided by Westell. After signing in, you can modify and check
information in SYSTEM SETTING.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 12 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Figure 1-1: Product Registration
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 13 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
1.4 Safety Guidelines
The general safety information in this guideline applies to both operations and service personnel.
Specific warnings and cautions are located in the applicable manual sections, but may not appear in this
summary. Failure to comply with these precautions or specific warnings elsewhere in the manual
violates safety standards of design, manufacture, and intended use of equipment. Westell assumes no
liability for the customer’s failure to comply with these requirements:
Grounding: This Signal Booster is designed to operate at 100-240V~, 50/60Hz, 2A power and must
always be operated with the ground wire properly connected. The ground wire must be at least 16 AWG
and must be connected to the building ground.
Explosive atmospheres: To avoid explosion or fire, do not operate this product in the presence of
flammable gases or fumes.
Lightning danger: Do not install or adjust this unit during an electrical storm.
No user-serviceable parts are inside the unit. Hazardous voltages are present when the cover is
removed. Opening the chassis will void your warranty. If you suspect a malfunction with this product,
call your dealer or Westell’s technical support line at 1.877.844.4274.
CAUTION
Turn the Signal Booster power off when connecting or disconnecting cables.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 14 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
1.5 Important Safety Information
Antennas used for the purpose of radiating signals indoors are limited to a maximum gain of 3 dBi.
Each antenna must be positioned to observe minimum separation requirements from all users and
bystanders.
The following guidelines must be used when considering separation distances:
•
Indoor antennas must be placed so that under normal conditions, personnel cannot come
within 20 cm (~8 in) of any inside antenna. Adhering to this minimum separation will ensure
that the employee or bystander cannot exceed RF exposures beyond the maximum
permissible limit as defined by FCC Regulations section 1.1310 Limits for general
population/uncontrolled exposure.
• Outdoor antenna must be positioned so that under normal conditions, personnel cannot
approach closer than 120 cm (~4 ft.). A directional antenna having a maximum gain of 3.75
dBi is used, and precautions should be taken to prevent personnel from routinely passing
through the main radiation beam at a distance closer than specified.
1.6 FCC Part 90 Signal Boosters
WARNING!
THIS IS A 90.219 CLASS B DEVICE
This is not a consumer device. It is designed for installation by FCC licensees and qualified
installers. You must have an FCC license or express consent of an FCC License to operate
this device. You must register class B signal boosters (as defined in 47 CFR 90.219) online
at www.fcc.gov/signal-boosters/registration. Unauthorized use may result in significant
forfeiture penalties, including penalties in excess of $100,000 for each continuing
violation.
FCC Warning Labels
The following labels will appear on the CS40-734834-00D-A0 Signal Booster in accordance with the FCC:
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 15 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
FCC Label Placement on the CS40-734834-00D-A0:
© 2019 Westell Technologies
1.877.844.4274
Right-Side View
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 16 of 52
CS40-734834-00D-A0 Product Manual
▣ FCC Part 15 Class A
April 2020, Rev A
Note:
This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with the instruction manual,
may cause harmful interference to radio communications. Operation of this equipment in
a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 17 of 52
April 2020, Rev A
CS40-734834-00D-A0 Product Manual
1.7 FCC Contact Information:
Federal Communications Commission
445 12th Street SW
Washington, DC 20554
Phone: 1-888-225-5322
TTY: 1-888-835-5322
Fax: 1-866-418-0232
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 18 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
2 Product Overview
2.1 Product Information
The CS40-734834-00D-A0 Signal Booster was developed for use in enclosed structures where signals
from local public safety towers to operate mobile units is poor or unavailable. Adequate signal
strength must be available outside the structure as a prerequisite to achieving in-building coverage.
The device is connected to an external antenna, normally located on a roof, and to one or more
internal antennas placed strategically throughout the area where wireless service is desired.
The external antenna is typically directional, such as a Yagi or Panel antenna. Internal antennas are
typically omnidirectional, although various other types may be used, depending on the coverage
application. The Signal Booster amplifies both the uplink (mobile to base) and downlink (base to
mobile) signals, thus facilitating communications to and from the intended wireless infrastructure.
With a maximum total of 90 dB nominal gain the downlink and 80 dB nominal gain the uplink, gain
can be adjusted over a range from 60(50) dB to 90(80) dB in 1 dB steps.
The Signal Booster is controlled using a computer connected to the RJ45 Female Network Connector
labeled ‘GUI’. There are also LED indicators to indicate alarm status, OSC and power. Refer to Figure
4-1.
The key features of this product are seamless interface to the 700/800 5W Composite DAS Ready
Dual Band Class A/B Public Safety Repeater (PSR), Modular Optical Master Unit (OMU) supporting 8
(eight) remote locations, local service area coverage at shared OMU and PSR location 5W composite
output power (2.5W each band), 32 UL Class A filters, mirrored operation and control through a
common GUI with the PSR. The product will also support Class B operation with filters selectable
wider than 75kHz. The product will be UL2524 compliant and certified.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 19 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Control using a Windows-based Graphical User Interface (GUI) and accessed by connecting
a laptop or desktop computer to the 8P8C/RJ45 Female Network Connector labeled ‘GUI’
2.2 Product Features
Easy installation
•
Light and small
•
•
• User gain control
• Automatic level control
• Automatic shutdown function
• Oscillation protection
• Overdrive protection
• Under/over voltage protection
Persistent status and error information
•
Fault protection
• Alarm notification
SNMP
•
•
• Battery Back-up Input
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 20 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
2.3 Included Accessories
Table 2-1 contains the items that are shipped with the CS40-734834-00D-A0 Public Safety Signal
Booster.
Table 2-1: Included Accessories
Quantity Description
1
1
1
9
1
2
AC Power 3 Wire Up to 16 AWG, Length : 6 ft
Ethernet cable, Length : 2 M
USB Drive containing the User Manual and Software
2M External Alarm Cable Whip - UL 2464 AWG20 20C
Drywall Anchors
Cabinet Keys
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 21 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
2.4 Optional Accessories
A complete line of accessories is available from Westell. Check with your Westell distributor for any
additional items needed. Some products that are suitable for most in-building needs are listed in
Table 2-2.
Table 2-2: Optional Accessories
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 22 of 52
© 2019 Westell Technologies
1.877.844.4274
Donor AntennaCSI-AY/746-896/11Clearlink-APD/698-940/-153/15/4310fServer/Coverage AntennaClearLink-O/698-2.7K/NClearLink-D/698-2.7K/NHybird Coupler4.3-10 Type ConnectorN-Type Connector3 dBClearLink-HC3/340-2.7K/NClearLink-HC3/340-2.7K/4310Power Tapper (Non-PIM Rated)4.3-10 Type ConnectorN-Type Connector6 dBClearLink-PT6/340-2.7K/4310ClearLink-PT6/340-2.7K/N7 dBClearLink-PT7/340-2.7K/4310ClearLink-PT7/340-2.7K/N8 dBClearLink-PT8/340-2.7K/4310ClearLink-PT8/340-2.7K/N10 dBClearLink-PT10/340-2.7K/4310ClearLink-PT10/340-2.7K/N13 dBClearLink-PT13/340-2.7K/4310ClearLink-PT13/340-2.7K/N15 dBClearLink-PT15/340-2.7K/4310ClearLink-PT15/340-2.7K/N20 dBClearLink-PT20/340-2.7K/4310ClearLink-PT20/340-2.7K/N30 dBClearLink-PT30/340-2.7K/4310ClearLink-PT30/340-2.7K/NDirectional Coupler (Non-PIM Rated)4.3-10 Type ConnectorN-Type Connector5 dBClearLink-DC5/340-2.7K/4310ClearLink-DC5/340-2.7K/N6 dBClearLink-DC6/340-2.7K/4310ClearLink-DC6/340-2.7K/N10 dBClearLink-DC10/340-2.7K/4310ClearLink-DC10/340-2.7K/N15 dBClearLink-DC15/340-2.7K/4310ClearLink-DC15/340-2.7K/N20 dBClearLink-DC20/340-2.7K/4310ClearLink-DC20/340-2.7K/N30 dBClearLink-DC30/340-2.7K/4310ClearLink-DC30/340-2.7K/N Power Divider (Non-PIM Rated)4.3-10 Type ConnectorN-Type Connector 2:1CLEARLINK-SPD2/340-2.7K/4310ClearLink-SPD2/340-2.7K/N 3:1ClearLink-SPD3/340-2.7K/4310ClearLink-SPD3/340-2.7K/N 4:1ClearLink-SPD4/340-2.7K/4310ClearLink-SPD4/340-2.7K/NAdapter4.3-10 (M) to N (F)CS48-132-633 Battery Back-up12/24 Hour Battery Back-upPS-BBU-01CS03-011-429CS03-012-389Yagi, 11 dB, Public Safety 700/800 (746-896 MHz)Panel Donor Antenna, Low-Band, 698-960, High IsolationCS40-734834-00D-A0 Product Manual
3 Product Specification
3.1 RF Specifications
ITEM
PARAMETER
DESCRIPTION
UNIT
NOTES
Table 3-1: RF Specifications
April 2020, Rev A
Class A Channelized Filter BW
12.5, 25, 50, 75, 100,
150
kHz
Default 75 kHz with minimum group delay, 100kHz
and 150kHz considered Class B
10
50 kHz @
f >105kHz
dB
f – is rejection from BAND EDGE
f tolerance +/- 5kHz
1
2
3
4
5
6
7
8
9
11
12
13
700 DL Freq. Band
700 UL Freq. Band
700 FirstNet DL Freq. Band
700 FirstNet UL Freq. Band
800 DL Freq. Band
800 UL Freq. Band
Number of DL Class A Filters per
Band
Number of UL Class A Filters per
Band
Class A Filter Rejections
12.5 kHz @
f >30kHz
25 kHz @
f >50kHz
75 kHz @
f >210kHz
100 kHz @
f >210kHz
150 kHz @
f >210kHz
Class A System Group Delay for each filter
12.5kHz
25 kHz
50 kHz
75kHz
100 kHz
150 kHz
Number of DL Class B Filters per
Band
Number of UL Class B Filters per
Band
758-776
788-806
758-768
788-798
851-869
806-824
32
32
>60
>60
>60
>60
>60
>60
<60
<36
<25
<15
<15
<15
4
4
MHz
MHz
MHz
MHz
MHz
MHz
PLUS FirstNet for 700 band
PLUS FirstNet for 700 band
TOTAL DL group delay between DONOR and
SERVICE ports.
Will not meet P25 phase 1 or 2 requirements
Will not meet P25 phase 1 or 2 requirements
uS
P25 phase 2 compliant
P25 phase 1&2 compliant
P25 phase 1&2 compliant
P25 phase 1&2 compliant
PLUS FirstNet for 700
PLUS FirstNet for 700
13.2
Class B Channelized Filter BW
0.250, 0.500, 1.0, 2.0,
3.0, 6.0, 7.0, 10
MHz
13.4
Class B Filter Rejections
f – is rejection from BAND EDGE
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 23 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
0.250MHz @
f >210kHz
dB
f tolerance +/- 20kHz
0.500MHz @
f >500kHz
1.0MHz @
f >500kHz
2.0MHz @
f >750kHz
3.0MHz @
f >750kHz
6.0MHz @
f >1MHz
7.0MHz @
f >1MHz
10MHz @
f >1MHz
FirstNet @
f >1MHz
Class B Group Delay for each filter
0.250MHz
0.500MHz
1.0MHz
2.0MHz
3.0MHz
6.0MHz
7.0MHz
10MHz
FirstNet
System Gain DL
System Gain UL
UL and DL Composite Gain
Adjustment
13.6
16
17
18
19
Gain Accuracy
20
AGC Range
>60
>60
>60
>60
>60
>60
>60
>60
>60
<15
<8
<6
<6
<6
<6
<6
<6
<6
90
80
30
30
+/-1
60
uS
TOTAL DL group delay between DONOR and
SERVICE ports.
dB
1 dB steps
dB
dB
dB
dB
Consists of 30dB available from composite gain
control and 30 dB available from individual channel
gain control
18.5
UL and DL Gain Adjustment per
Channel (Filter)
dB
1 dB steps – Attenuation adjustment
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 24 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
3.2 Power Specification
Table 3-2: Power Specifications
Parameter
Main Power Input Voltage
Battery (ACM-31 type)
Power Consumption
Specification
100-240V~ 50/60 Hz
22.5 VDC to 27 VDC
100-240V~, 50/60 Hz.
Note
AC Power
Battery Voltage
< 2.0 A Max.
Max. 2.7 A
Battery full Charging within 48hous
3.3 Mechanical Specification
Table 3-3: Mechanical Specifications
Parameter
Size
Specification
14.9 x 18.7 x 5.3 in
Note
L x H x D
Donor/Coverage Antenna Ports: 4.3-10 (f)
Matting Male Connector Torque 3.7 ft.-lbs.
AC Power In (8402 Gland Connector)
Open Wire Terminal (Pig tail)
DC (Battery) Power In (8402 Gland Connector)
Open Wire Terminal (Pig tail)
Connectors
Accessory (8404 Gland Connector)
DAS OMU Interface
Alarm Relay (8404 Gland Connector)
Alarm Relay Interface
Annunciator (8402 Gland Connector)
Remote Annunciator Interface
RJ-45 Ethernet-1 (10/100 Base-T)
GUI Interface
Mounting Type
Enclosure Lock
Heat Dissipation
Finish
Frame Ground
Wall-Mount with 8 holes
Key Lock
Natural Convection
Red color Paint
© 2019 Westell Technologies
1.877.844.4274
Two-Lug Ground
4 holes in each side
Two-Key Lock
RAL3001 Signal RED
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 25 of 52
ADCATT1MIXLPFDL800UL(700+800)UL(700+800)DL800 HPASAWDACDACISOCAVITYTRIPLEXERSERVICEMONOTRIPLEXERDETDNCBPFLNADETDONORHPAHPADL700 HPADIVAMPDL700ATT2AMPRFIFLORFIFLOAMPAMPDETADCAMPSAWAMPMIXRFIFLORFIFLOBPFATT3AMPATT4BPFAMPDETDETDL700DL800LNAATT1AMPATT2AMPMIXBPFRFIFLORFIFLOLPFSAWDETDETAMPAMPDETADCDACDACADCUL HPAHPAAMPSAWAMPMIXRFIFLORFIFLOBPFATT3AMPATT4BPFDETAMPUPCPower Supply100 ~240VAC+28VDCChargerBattery +24VDC+28VDC+9VDCWeb GUI BoardRelay BoardCS40-734834-00D-A0 Product Manual
3.4 Environmental Specification
April 2020, Rev A
Table 3-4: Environmental Specifications
Parameter
Specification
Operating Temperature
-30°C ~ +50°C (ambient)
Storage Temperature
-40°C ~ +60°C (ambient)
Operating Humidity
5% ~ 95%
Environmental
IP-67, NEMA 4 Compliance
Note
-22°F ~ +122°F
-40°F to +140°F
3.5 GUI Items
Parameter
UL/DL Output Readings
UL/DL Shutdown Setting
UL/DL Gain Setting
/ Attenuation
System Display
Location Display
Isolation
Alarm Readout Displays
Displays alarm status
Note
Reads and displays the UL/DL output power
Table 3-5: GUI Items
Specification
UL : 5dBm to 30dBm
DL : 5dBm to 36dBm
Loss of AC Power - Battery Depleted
Donor Antenna Fail1
Oscillation Detection1
Temperature Fail
UL/DL Amplifier Fail
Donor Antenna Fail2
Oscillation Detection2
Loss of Ra/DRA COMMS
Battery Charger Fail
Door Open
Emergency Power Off
UL : 30dBm
DL : 36dBm
UL : 50dB to 80dB Gain
DL : 60dB to 90dB Gain
0dB to 30dB Attenuation.
Use to set the peak power
(shutdown level)
Used to set the UL/DL system gain.
Manufacturer, Repeater Type, Repeater S/N, S/W
Version, Temperature
Displays the repeater name and
information.
Control Send
All Control Page Settings
Company, Address, City, State,
Contact
Displays the repeater location information.
Used to save settings in the Control page.
Isolation Value, Isolation Max Gain Display
Refer to Section 6 System Operation for more information about the GUI.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 26 of 52
CS40-734834-00D-A0 Product Manual
3.6 Alarm Status
April 2020, Rev A
Table 3-6 Alarm Status
PSR Alarm State
PSR Action
GUI/SNMP Alarm
Description
Loss of AC Power - Battery Depleted
NA - System dead
NA - System dead
NA - System dead
Donor Antenna Disconnect
None
Donor Antenna Disconnect
Donor Antenna Disconnect
Oscillation RF Shutdown
RF shutdown
System component
Oscillation detection
Uncorrectable Oscillation detected,
RF shutdown
Temperature fail
None
Temperature
High temperature alarm
UL/DL Amplifier fail
UL and DL separate alarms
RF shutdown
DL 700 HPA fail
UL/DL Amplifier fail
UL and DL separate alarms
UL HPA fail
DL 800 HPA fail
Donor Antenna Malfunction
None
Donor Antenna Malfunction
Donor Antenna Malfunction
Oscillation Reduced Gain
Reduce Gain
Oscillation Reduced Gain
Oscillation detected - Gain Reduced
Loss of RA/DRA COMMS
Annunciator Communication Lost
Remote Annunciator loss of
Communication
Battery capacity low
Battery capacity
Battery capacity low
Battery charger fail
Battery charger fail
Battery charger fail
Door open
Door open
Door open
Emergency power off
RF shutdown
User initiated Emergency power off
User initiated Emergency
power off
Loss of AC Power
Battery working
None
Loss of AC Power
Loss of AC Power
None
None
None
None
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 27 of 52
CS40-734834-00D-A0 Product Manual
3.7 Alarm Relay
April 2020, Rev A
Table 3-7 Alarm Relay
PSR Alarm State
PSR Action
PSR Relay/Annunciator Alarm
Description
Loss of AC Power - Battery Depleted
NA - System dead
NA - System dead
NA - System dead
Donor Antenna Disconnect
v
Donor Antenna Disconnect
Donor Antenna Disconnect
Oscillation RF Shutdown
RF shutdown
System component fail
RF Emitter fail
Uncorrectable Oscillation detected,
RF shutdown
Temperature fail
None
System component fail
High temperature alarm
UL/DL Amplifier fail
UL and DL separate alarms
RF shutdown
RF Emitter fail
UL/DL Amplifier fail
UL and DL separate alarms
Donor Antenna Malfunction
None
Donor Antenna Malfunction
Donor Antenna Malfunction
Oscillation Reduced Gain
Reduce Gain
System component fail
Oscillation detected - Gain Reduced
Loss of RA/DRA COMMS
System component fail
Annunciator Communication Lost
Battery capacity low
Battery capacity low
Battery capacity low
Battery charger fail
Battery charger fail
Battery charger fail
Door open
None
Door open
None
None
None
None
Emergency power off
RF shutdown
RF Emitter fail
User initiated Emergency power off
Loss of AC Power
Battery working
None
Loss of AC Power
Loss of AC Power
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 28 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Either method in Table 3-7 would trigger the following alarms: AC
Power Fail, Battery Capacity Low, Battery Charger Fail, RF Emitter Fail,
Donor Antenna Malfunction/Disconnection and System Component
Fail.
NOTE
ALARM 1 : EMERGENCY POWER OFF (Pin 1,2)
ALARM 2 : AC POWER NORMAL (Pin 3,4,5)
ALARM 3 : LOSS AC POWER (Pin 6,7,8)
ALARM 4 : BATTERY CAPACITY LOW (Pin 9,10,11)
ALARM 5 : BATTERY CHARGER FAIL (Pin 12,13,14)
ALARM 6 : RF EMITTER FAIL (Pin 15,16,17)
ALARM 7 : DONOR ANTENNA MALFUNCTION (Pin 18,19,20)
ALARM 8 : DONOR ANTENNA DISCONNECT (Pin 21,22,23)
ALARM 9 : SYSTEM COMPONENT FAIL (Pin 24,25,26)
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 29 of 52
CS40-734834-00D-A0 Product Manual
4 Product Appearance
4.1 External Configuration
April 2020, Rev A
Figure 4-1: External Product Configuration
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 30 of 52
CS40-734834-00D-A0 Product Manual
5 Installation Guidelines
5.1 Important Installation Guidelines
April 2020, Rev A
•
•
•
The CS40-734834-00D-A0 Signal Booster is designed for indoor use only.
The CS40-734834-00D-A0 Signal Booster must be installed in a vertical orientation (i.e.
Connectors on the bottom of the unit).
Inadequate isolation between the outside and inside antennas may cause regenerative
feedback in the system.
This feedback can cause the amplifier to emit a continuous signal at maximum
amplitude, and, in some cases, interfere with normal operation of the donor site.
Careful consideration of the layout and placement of the system is imperative to
minimize this possibility and to minimize the amount of signal leaking from the
building.
• Do not disassemble the Signal Booster.
DANGER!
• Refer to the 1.3 Safety Guidelines section for proper antenna selection and
installation. To avoid serious injury, death and/or damage to the Signal
Booster, do not install donor or server antennas near overhead power lines or
high power components. Allow enough distance so that falling antennas
would not come in contact with those components.
•
Electric shock may occur if the Signal Booster is installed in close proximity to
water.
WARNING!
• Amplifier or handset damage may occur if a handset is connected directly to
the Signal Booster or to the coax that leads to the Signal Booster.
•
The CS40-734834-00D-A0 Signal Booster must be connected to ground for
protection.
• We recommend that installers do not wear jewelry or metal accessories when
installing this Signal Booster.
• Do not place cables or tools that may damage the Signal Booster in close
proximity to it.
•
•
Check the installation site for hazardous conditions such as water-covered
floors or badly worn or damaged cables prior to installation.
Lifespan and performance of the Signal Booster may be reduced if the unit is
operating outside its nominal temperature range.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 31 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
CAUTION
Close proximity to the donor or server antennas with the Signal
Booster in operation may expose users or installers to RF fields that
exceed FCC limits for human exposure.
Turn power to the Signal Booster off when connecting or disconnecting
cables.
•
•
• Be careful as there is a very high voltage inside Signal Booster. Key is
required to open Signal Booster, but the key must be kept by the
administrator who manages the product.
5.2 Donor Antenna Installation Guidelines
• Accurately determine the azimuth to the donor site. Obtain the donor site information and
approval from the service provider/carrier.
•
Ensure that the radiation path to the donor site is unobstructed.
• Mount the donor antenna at or toward the edge of the roof, in the direction of the donor
site. Avoid having the RF signal from the donor pass above the location(s) of the service
antennas. Normally, the service antennas are installed behind and below the donor antenna,
as viewed from above. This approach helps avoid interference and feedback to and from the
service antennas.
• Normally, mounting the donor antenna higher will allow a less obstructed path to the donor
site. However, in high traffic metro areas, avoid mounting the donor antenna higher than
necessary, as the quality of the donor signal may become less stable and it is more likely to
encounter adjacent channel interference.
• When possible, shield the rear of a donor antenna by locating it so that any HVAC units
and/or penthouse structures are behind the antenna, relative to the donor cell site location.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 32 of 52
CS40-734834-00D-A0 Product Manual
5.3 Indoor Antenna Installation Guidelines
April 2020, Rev A
• Use omnidirectional antennas (see section 2.4. Optional Accessories) indoors and locate
them centrally with respect to the intended coverage area to minimize signal leakage to the
outside. Only use directional antennas indoors in special cases when higher gain and
directionality would be helpful and RF exposure limits will not be exceeded.
•
•
To avoid Signal Booster uplink overload and gain limiting, mount the indoor antennas away
from areas where mobile subscribers frequently use their phones / radios, such as desks or
dispatch areas. Note: If the signal level from antenna at the UL service port is >-12dBm,
add external attenuation to avoid shutdown alarm
To determine the quantity and locations of indoor antennas, measure Received Signal
Strength Indication (RSSI) using DM Tool software to determine areas of weak signals. These
are the approximate areas where indoor antennas may be needed.
• Be aware that the signal from an indoor antenna, in most cases, can be expected to
penetrate approximately two standard sheet rock walls to reach users. If the signal must
travel through more than two walls, or if the walls are made of materials other than sheet
rock, it may be necessary to split the available signal and add more antennas.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 33 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
5.4 Mounting the Signal Booster
Follow the instructions in this section to mount the Signal Booster on a wall.
Mounting Holes
Mounting Holes
Mounting Holes
Mounting Holes
Figure 5-1: Signal Booster Mounting
1. Using the CS40-734834-00D-A0 as a template, mark the four (8) locations for the
wall anchoring system screws.
2. Move the CS40-734834-00D-A0 unit and drill the mounting holes at the marks in
the wall.
Install a wall anchor (8mm x100mm) in each of the four (8) drilled holes.
3.
Install the top two (4) screws into the anchors, leaving enough room to slide the
screws into the oblong holes of the top of the unit’s mounting positions.
4. Once the Unit is hung on the top two (4) screws finish fastening the top screws.
5.
Install the bottom two (4) screws into the anchors, fastening the Unit to the wall.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 34 of 52
CS40-734834-00D-A0 Product Manual
5.5 Verifying the Physical System Setup
April 2020, Rev A
•
•
•
Check all cables for shorts and opens. Verify that there are no cables with loose or poor
connections. RF leakage could cause oscillation to occur under some conditions.
If the rooftop antenna (donor antenna) is directional, check it for proper alignment along
the calculated compass heading. Typically, the directional antenna would be aimed at the
same site that your handset uses, but that may not always be the case.
If cables and alignment are acceptable, and a problem persists, use a spectrum analyzer to
examine the signal environment in which the unit is operating. The existence of strong
adjacent channel signals within the frequency band(s) can cause the AGC to reduce the
amplifier’s gain or cause alarms. In some cases, additional filtering or attenuation may be
required to reject these unwanted signals. In some instances, the donor antenna can be
reoriented horizontally to place the interference source in an antenna pattern null.
5.6 Controlling the Signal Booster
Control and monitoring the Signal Booster requires that a properly configured computer with Westell
CS40-734834-00D-A0 control software installed is connected via an Ethernet cable, such as the one
shown in Figure 5-2A. Connect the Ethernet cable from the Network Interface port of a computer to
the GUI port on the bottom end panel of the Signal Booster.
Figure 5-2A: Ethernet Cable
RJ45
GUI
GUI
Figure 5-2B: Ethernet Connectors
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 35 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
5.7 Connecting to the Alarm Relay Panel
Use the provided Alarm Relay Serial Cable to connect the Public Safety Signal Booster to the alarm
relay panel. If the provided cable is not long enough for your system, you will need to build one.
1. Strip the outer serial cable insulation back to expose the inner conductors, Figure
5-3.
2. Strip back the insulation on the ends of each conductor. (Tin wires as needed.)
Figure 5-3: Stripped Alarm Wire
3. Remove HFC 8404 Gland Connector and feed alarm cable through fitting.
Figure 5-4: Alarm Relay 20-wire Gland Connector HFC 8404
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 36 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
4. Connect the HFC 8404 Gland connector at the serial cable to the Alarm Relay
connector on the PSR, Figure 5-5. Be sure to fasten the connector screws
securely.
Figure 5-5: Alarm Relay Cable Connected to Repeater
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 37 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
1. Connect the stripped end of the serial cable to the alarm relay panel. Refer to
Table 5-1 for connection information.
Table 5-1: Alarm Relay Connections
Alarm Information
Relay Status
EMERGENCY POWER OFF
Alarm Information
Relay Status
AC POWER NORMAL
LOSS AC POWER
BATTERY CAPACITY LOW
BATTERY CHARGER FAIL
RF EMITTER FAIL
DONOR ANTENNA MALFUNCTION
DONOR ANTENNA DISCONNECT
SYSTEM COMPONENT FAIL
Normal → NC+CC
Alarm → NO+CC
Alarm#
Alarm1
Description
IN
1
OUT
2
Alarm#
Description
NC
NO
CC
Alarm2
Alarm3
Alarm4
Alarm5
Alarm6
Alarm7
Alarm8
Alarm9
3
6
9
12
15
18
21
24
4
7
10
13
16
19
22
25
5
8
11
14
17
20
23
26
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 38 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
5.8 Connecting the Power Cable
Use the provided AC Power Cable to connect the Public Safety Signal Booster to an AC power source.
1. Remove the HFC 8402 Gland Connector Molded from the AC 100~240V
power connector on the Signal Booster, Figure 5-6.
Remove
HFC 8402 Gland
Connector Molded
Figure 5-6: Remove the Power Connector Cap
2. Connect the power cable to the AC 100~240V power connector on the
Signal Booster, Figure 5-7.
The Signal Booster connector and the cable connector are keyed as shown in Figure 5-7.
NOTE
Connection
F.G, AC_N, AC_L
Alarm Relay Board
Figure 5-7: Connection AC Power Cable
3. Screw the connector on securely.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 39 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Screw the
connector on
securely
Figure 5-8: Power Cable Connected to Repeater
4. When the Signal Booster is properly set up and ready to have power applied,
plug the other end into the Cabinet 100~240 VAC.
Figure 5-9: Power Cable Connected to Signal Booster
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 40 of 52
CS40-734834-00D-A0 Product Manual
5.9 Connecting the Battery Back-up Cable
April 2020, Rev A
Use the provided DC Power Cable to connect the Public Safety Signal Booster to a 24-30VDC Battery
Back-up / power source. (Pin A, White = positive, Pin B, Black = Negative)
Warning: Do NOT use DC Power Supply instead of Battery
Figure 5-10: Battery Cable Connected to Signal Booster
5.10 BBU Specification
Battery Model
NSB-AGM31
Internal resistance
2.2 mΩ @25°C
Pulse Cranking Amps
2150 A
Short Circuit Current
5000 A
CCA rating at -18°C (0°F)
1150 A
Q’ty Batteries of BBU
2
Capacity – 20HR rate
103 Ah
Reserve Capcity
220 min
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 41 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
6 System Operation
6.1 Operating the Program
Access the Public Safety Signal Booster through a LAN connection. The Signal Booster ships with the
IP address 192.168.0.1 on the GUI port.
To connect directly to the Signal Booster from a laptop or PC with a crossover CAT-5E cable or over a
LAN, change the TCP/IP settings on your computer to enable a connection to a host that has a static
IP.
PC Set-up: Open Control Panel→ Network Connections → Local area connection
Figure 6-1: Network Connection Set-up
1) Select Use the following IP Address and enter the IP address 192.168.1.x, where ‘x’ is any number
from 2 to 254, inclusive, other than 150
2) Ensure that the subnet mask is set to 255.255.255.0
3) Web Browser: Chrome/Internet explorer
Username: admin
Password: Password
Figure 6-2: Web GUI Log in
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 42 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
6.2 Web GUI System Status
When you log-in, the System Status window is displayed, and the four menus in which the sections are
described are activated. The top menu displays Alarm, and if you click it, you can check the entire alarm
Figure 6-3: Web GUI System Status
Item Description
Alarm Page (Check the alarm status)
RF Configuration (Setting the RF mode)
Configuration Export (Exporting information from equipment)
Annunciator Test (Alarm and LED test)
System Setting (Check your system settings and download F/W)
①
②
③
④
⑤
6.3 Alarm Page
Figure 6-3: Alarm Configuration
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 43 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Item #
Section
Loss Of AC Power
Fail of AC Power
Battery Capacity Low
Low Battery capacity at 70% reduction
Battery Charger Fail
Battery Disconnection or Battery No charging status
DL 700 HPA Fail Downlink 700MHz HPA Upper/Lower Current Limit
DL 800 HPA Fail Downlink 800MHz HPA Upper/Lower Current Limit
UL HPA Fail Uplink HPA Upper/Lower Current Limit
High Temperature Detected Out of the set temperature range Checked
Donor Antenna Disconnect Donor ANT Disconnection Checked
Donor Antenna Malfunction Donor ANT VSWR Check Fail/ Donor ANT Malfunction
Oscillation Reduced Gain Gain adjustment when oscillation occurs
Oscillation RF Shutdown Output off when oscillation is not resolved
System Component Fail
System Component Fail Alarm
Door Open Door status check
User Initiated Emergency Power Off
System off when an Emergency occurs
Remote Annunciator Loss Of Communication Loss Annunciator connection check
Not User-Configurable/ Alarm Test and Alarm Informational Only.
( GREEN = Normal; Yellow = Alarm )
Alarm Monitoring
Alarm History
Click the Alarm History Button
check the history of alarm occurrence by time and details
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 44 of 52
CS40-734834-00D-A0 Product Manual
6.4 RF Configuration
April 2020, Rev A
Figure 6-4: RF Configuration
Band
700MHz, 800MHz Band Selection Menu
Channels
32Ch. Selection Menu
Section
Section
Section
Section
Output Power
UL DL output power of selected band is monitored
Isolation
Antenna isolation measurement
Item 1
Item 2
Item 3
Item 4
Item 5
Section
Mode
Class A,B Selection Menu
If Class A,B is set, the selectable channels are displayed differently.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 45 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
Item 1
Item 6
Section
Section
Item 7
Section
Item 8
Section
Gain
DL, UL Gain setting
DL Max Gain: 90dB
UL Max Gain: 80dB
Squelch
Displays DL, UL Automatic Level Control
Level setting value
ALC
Displays DL, UL Automatic Level Control
Level setting value
HPA
Sets DL, UL HPA On/Off
Item 9
Section
Item 10
Section
Channel Selection
Setting the center frequency of the filter
Setting the Band Width(BW) of the filter
Filter output power monitoring
Attenuator control
Sets ALC On/Off
Sets ACL Level setting value
Sets Filter On/Off
EDIT
Settings can be made through Edit.
Clicking the Edit button shows the items that can be set.
Class A can operate a total of 32Ch
Class B can operate a total of 4Ch
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 46 of 52
CS40-734834-00D-A0 Product Manual
6.5 Annunciator Test
This test will actuate:
April 2020, Rev A
1) the audible annunciator for each alarm in the repeater enclosure
2) the audible and visible annunciator for each alarm in the remote annunciator panel
3) Test All: Enable alarm testing via the software GUI
Figure 6-5: Annunciator Test
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 47 of 52
CS40-734834-00D-A0 Product Manual
April 2020, Rev A
7 System Software Upgrade
7.1 Upgrading the System Software
Follow the instructions in this section to upgrade to a newer version of system software, as required.
1) Click the “System Setting” button on the System Status to display the Control page.
2) System Upgrade progress window, Figure 7-1, displays.
3) Navigate to Integrated SW Upgrade folder
Figure 7-1: System Firmware Upgrade Progress
②
①
③
Figure 7-2: Window File Open Tab
4) Select the File PDT.INTEGRATED.0.XX.XX.zip and press. Never extract the compressed file. Select
the zip file as it is
5) Click
in the System file upload dialog window, system upgrade begins, as indicated by
the progress bar in the system upgrade window.
The firmware upgrade takes about 30 minutes.
6) Check the version after completing the upgrade
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 48 of 52
CS40-734834-00D-A0 Product Manual
7.3 Network (WAN) Setting
April 2020, Rev A
Figure 7-3: Network Display
1) Select “SYSTEM SETTING” button
2) Select “Network” section “EDIT” button
3) Fill network setting value(Prefix 24 is same subnet mask 255.255.255.0)
•
IP setting
IP Address: 192.168.0.100
Subnet Mask: 255.255.255.0
Gate way: 192.168.3.1
DNS Server: Auto
Figure 7-4: IP Settings
4) You can access PSR control page anywhere.
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 49 of 52
CS40-734834-00D-A0 Product Manual
Appendix A Important Product Information
April 2020, Rev A
Part Number
Band
Bands
Class
Description
CS40-734834-00D-A0
700 / 800
Dual
DB-700/800 2.5W CL-A/B
A.1 Registration Number
FCC - NVRDPSA81090-78
A.2 ETL
This product is ETL Listed. #5018566
A.3 Configuration LIST
CS40-734000-00D-A0
CS40-000834-00D-A0
CS40-730000-00D-A0
CS40-000830-00D-A0
CS40-727000-00D-A0
CS40-000827-00D-A0
CS40-734000-00D-B0
CS40-000834-00D-B0
CS40-730000-00D-B0
CS40-000830-00D-B0
CS40-727000-00D-B0
CS40-000827-00D-B0
A.4 Accessory
700
800
700
800
700
800
700
800
700
800
700
800
CS40-730830-00D-A0
700 / 800
Dual
DB-700/800 1W CL-A/B
CS40-727827-00D-A0
700 / 800
Dual
DB-700/800 .5W CL-A/B
Single
Single
Single
Single
Single
Single
Single
Single
Single
Single
Single
Single
A/B
A/B
A/B
A/B
A/B
A/B
A/B
A/B
A/B
B
B
B
B
B
B
B
B
B
SB-700 2.5W CL-A/B
SB-800 2.5W CL-A/B
SB-700 1W CL-A/B
SB-800 1W CL-A/B
SB-700 .5W CL-A/B
SB-800 .5W CL-A/B
SB-700 2.5W CL-B
SB-800 2.5W CL-B
SB-700 1W CL-B
SB-800 1W CL-B
SB-700 .5W CL-B
SB-800 .5W CL-B
CS40-734834-00D-B0
700 / 800
Dual
DB-700/800 2.5W CL-B
CS40-730830-00D-B0
700 / 800
Dual
DB-700/800 1W CL-B
CS40-727827-00D-B0
700 / 800
Dual
DB-700/800 .5W CL-B
CS40-DASANNUNCIATOR
DAS Master Annunciator
CS40-ANNUNCIATOR
BDA / DAS Remote Annunciator
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 50 of 52
CS40-734834-00D-A0 Product Manual
Appendix B Acronyms and Abbreviations
April 2020, Rev A
Table B-1 contains the acronyms and abbreviations used in this manual, along with a definition for
each one.
Table B-1: Acronyms and Abbreviations
Acronym/Abbreviation Definition
IF SAW
Intermediate Frequency Surface Acoustic Wave
AC
AGC
COM
dB
dBc
dBi
dBm
DC
DL
FCC
HPA
IP
LAN
LED
MHz
NMS
OSC
PLL LD
RF
RS-232C
UL
UPS
VAC
VSWR
Alternating Current
Automatic Gain Control
Communications
Decibels
Decibels relative to the carrier
Decibels relative to isotropic
The power ratio in decibels (dB) of the measured
power referenced to one milliwatt (mW)
Direct Current
Downlink
Federal Communications Commission
High-Powered Amplifier
Internet Protocol
Local Area Network
Light Emitting Diode
Megahertz
Network Management System
Oscillator
Phase-locked loop with lock detection
Radio Frequency
Serial Communication Standard
Uplink
Uninterruptable Power Supply
Volts Alternating Current (AC Voltage)
Voltage Standing Wave Ratio
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 51 of 52
April 2020, Rev A
CS40-734834-00D-A0 Product Manual
Appendix C UL2524 Installation Guidelines
UL2524 Installations
AC Input Connector
- 1/2” Liquid Tight Conduit Fitting - Heyco 8402
- 1/2” Cordgrip - Heyco M6108
DC Input/Output Connector
- 1/2” non-metallic Conduit fitting - Heyco 8402
- 1/2” Cordgrip - Heyco M6108
Accessory Connector
- 3/4” non-metallic Conduit fitting - Heyco 8404
- 3/4” Hole Plug - Heyco 3835
Alarm Relay Connector
- 3/4” non-metallic Conduit fitting - Heyco 8404
- 3/4” Cordgrip - Heyco M6110
Annunciator Connector
- 1/2” non-metallic Conduit fitting - Heyco 8402
- 1/2” Hole Plug - Heyco 3833
© 2019 Westell Technologies
1.877.844.4274
WESTELL.COM
April 2020; Doc No. CS14702802UM rD
Page 52 of 52
FCC compliance information
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause undesired operation.
1 2 | External Photos | External Photos | 287.66 KiB | January 26 2021 / July 25 2021 | delayed release |
1 2 | label | ID Label/Location Info | 3.54 MiB | January 26 2021 |
Labels:
RoHS Compilant WESTELL 38.10 3 1 4 I $ i 6 L 7 1 8 T Rev. | Customer Rev. Description Date Reviser Checked
= Tarpon avg ine] San | nang [to 76.20 _ S40-000830-00D-B0 Listed SB-800 1WCL-B Rating 100-240V~, 50/60Hz, 2A Model CS40-734834-00D-AO Rev-10 12/2020 e ve FCC ID NVRDPSA81090-78 Conforms to UL STO. 62368-1 Certified to CSA STD. r WESTELL BNotes. 1, Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) 4. No text smudging, erasing. ete. 5. Quantity ; 1EA Separate Label Attachment Barcode Format: Code 39 or 128. Scale size to fit as needed Design And Process Change No Changes In Material Design Or Process Which Will Effect Form, Fit Or Function Shall Be Made By The Manufacturer After DWG.Name |PSR Label-1 ite Mec, Design |M.R.Yang Public Safety Repeater le. Design |CH.Lee IT-DWG No. | 1T1098001-POx Sample Approval Without Approve | $.D.Seo Ory, Witten Authority From innertren INNERTRON Unit mm eo =} | SHT 1/1 | Scale 1:1 3 T a a 3 T T 7 T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL FCC ID : NVROPSA81090-78
# L 4 | 5 L 6 l 7 i 8 t Rev. |Castomar Rev.| Description Date Reviser_[ Checked Ro 2 Temporary droning wae | senotiaa | MRvang | sychel _ 76.20 . CS40-734834-00D-A0 Listed DB-700/800 2.5W CL-A/B Rating 100-240V~, 50/60Hz, 2A Model : CS40-734834-000-A0 Rev 1.0 12/2020 e we Separate Label Attachment
= Intertek o 5018566
~ Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 6236:
Barcode Format: Code 39 or 128. r Scale size to fit as needed E 7 Notes F 1, Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-019) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) a 4..No text smudging. erasing etc. 5. Quantity :1A G6 Design And Process. OWG.Name |PSR Label-1 jes Cure Public Safety Repeater 4 No Changes in Material i ublic Safety Repe Deoge O Procees Mhach | |_ Mee: Desion |M.R.Yang waEies re, | Ona [even Tone no | iesonr 0 H The Manufacturer After *
Sample Approval Without Approve | $.D.Seo 7 Wain Aahotty From Innertren INNERTRON Unit mm | @ ep] SHT 1/1 | Scale 1:1 3 T 4 5 T T z T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 WESTELL ols Compliant
{OHS Comel I 2 I 3 | 4 | 5 6 ! z L 5 T Rev. | Customer Rev. | Description Dare Reviser Checked Fo Z Texpery drawing wwe tetra | MRvang | Svat A 8 76.20
CS40-734834-00D-BO Listed DB-700/800 2.5W CL-B Rating 100-240V~, 50/60Hz, 2A 4 Model : CS40-734834-00D-A0 Rev 1.0 12/2020 e us FCC ID NVROPSA81000-78 Separate Label Attachment 2
, s Conforms to UL STD. 62368-1 Certified to CSA STD. Barcode Format: Code 39 or 128. o r Scale size to fit as needed WESTELL E
| BNotes, F 1. Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) J 4. No text smudging, erasing, etc. 5. Quantity : TEA, G Design And Process DWG.Name [PSR Label-2 iis Change: Public Safety Repeater 4 No In Material He Sore iol Mec. Design | M.R.Yang Pesbungphivyiebelge Ele. Design |CH.lee IT-DWG No. | 1T1098001-Po02 4 The Manufacturer After *
Serle en hone Approve |S.D.Seo 4: I t en rom INNERTRON Unit mm | @ ep] SHT 1/1 | Seale 1:1 ( nnertren 1 T 2 T 3 T 4 a 5 T 6 T 7 T AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 WESTELL RoHS Compliant OHS Complia Ll 2 1 3 Ll 4 I 5 Ll 6 l 7 I 8 T Rev. |Gustomar Rav. Description Date Reviser | Checked FO z Tenperay drawing une | eearri | Maverg | sychel A 8 76.20 _ c CS40-734000-00D-AO Listed SB-700 2.5W CL-A/B Rating 100-240V~, 50/60Hz, 2A
| Model -CS40-734834-000-A0 Rev-1.0 12/2020 ve s ie/label Attach f oO FCC ID: NVRDPSA81090-78 eparate Labe acnmen
= Intertek
. oO. 5018566 o. Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62:
Barcode Format: Code 39 or 128. D in Scale size to fit as needed WESTELL e
| MNotes, F 1. Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) 4 4, No text smudging, erasing, etc. 5. Quantity : 1EA s Design And Process OWGName |PSR Label-3 ee Change q 4 fio Changes In Mates! waa. Onaga |MiRYong Public Safety Repeater Design Or Process Which ae ate oat Ge. Design [CH.lee IT-DWG No. | 1T1098001-P003 4 The Manufacturer After Sample Approval Without Approve | S.0.Seo <7 age bees Ce Innertren INNERTRON Unit mm | @ ep] SHT 1/1 | Seale 1:1 1 T 2 T 3 T 4 5 T 6 T 7 T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL Il 7 76.20 Rev. [Customer Rav. Description Date Reviser Checked RO Terporary Srtwing meue BOOTIE MRD, Sychot 38.10 CS40-734000-00D-B0 Listed SB-700 2.5W CL-B Rating 100-240V~, 50/60Hz, 2A Model : CS40-734834-000-A0 Rev 10 12/2020 e FCC ID :_NVRDPSA81090-78 Intertek 5018566 Separate Label Attachment D Conforms to UL STD. 62368-1 Certified to CSA STD. C222 No. 62 Barcode Format: Code 39 or 128. o rc Scale size to fit as needed WESTELL l e
| Notes, F 1. Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification ; UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts)
= 4. No text smudging, erasing, etc. 5. Quantity : 1A G Design And Process DWG.Name |PSR Labels re cues Public Safety Repeater
=~ No Changes In Material Mec. Design | M.R.Yang Hy Rep!
Design Or Process Which Peacien Sica Be Mage By He. Design |C.H.lee IT-DWG No, | 1T1098001-Po04 4 The Manufacturer After =
Sample Approval Without Approve |$.D.Seo ae: o ec A Fee innertren INNERTRON Unit mm | @ =f] SHT 1/1 | Scale 1:1 z 3 T q a 5 T 7 T 8 aS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 3 1 4 | S 6 I # l 8 T Rev. |Custamer Rav. Description Date Reviser Checked 7% z Tenperay Siawing wae | f0n0T11 | MRYang | SyChel A 4 8
= 76.20 <j c CS40-000834-00D-A0 Listed SB-800 2.5W CL-A/B Rating 100-240V~, 50/60Hz, 24
| Model : CS40-734834.000-A0 Rev:1.0 12/2020 we s fe Babel Attaeh t
| FCC ID : NVRDPSA81090-78 eparate Labe' acnmen
= Intertek D ) 5018566
~) Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62;
Barcode Format: Code 39 or 128. D rc Scale size to fit as needed E
| WNotes, F 1. Quality of the material : White Polyester (J WORLD CO LTO JW-916 or JW-019) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) J 4. No text smudging. erasing. etc. 5. Quantity ; 1EA G rie Design And Process DWG.Name | PSR Label-5 Change Public Safety Repeater 4 No In Material g ne in ae bs Mec. Design |M.R.Yang Fineive Sl Be oce By | De. Design |CH.lee IT-DWG No. | 1T1098001-PO0S H The Manufacturer After =
Sample Approval Without Approve | $.0.Seo ee Whitten Authority From Innertren INNERTRON Unit mm | @ <p] SHT 1/1 | Seale 1:1 3 T z a 5 T T 7 T 8 75 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 WESTELL RoHS Compliant \ 2 i 3 4 ; 2 L z 1 S T Description Date Reviser_| Checked
% : Tenperay droning neve | Soeariia | wayang | sycrol A 8 76.20 _ c CS40-000834-00D-BO Listed SB-800 2.5W CL-B Rating 100-240V~, 50/60Hz, 2A
| Model CS40-734834-00D-A0 Rev: 1.0 12/2020 bi s tetLabell Addach o FCC ID : NVRDPSA81090-78 eparate Label aacnmen
= Intertek 2. 5018566
. Conforms to UL STD. 62368-1 Certified to CSA STD. C222 No. 6236 Barcode Format: Code 39 or 128. o r Scale size to fit as needed WESTELL ]
e
| MNotes,
: 1. Quality of the material ; White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) i 4, No text smudging, erasing, etc. 5. Quantity : 1EA 6 Tie Design And Process DWGName [PSR Label-6 Change i tf ca i eneisiia jane Boag [WiRiYonp Public Safety Repeater Or Process Which Pension Stor Be Mave By | He: Design |CHlee IT-DWG No. | 1T1098001-PO0 H The Manufacturer After . Sample Approval Without Approve | $.0.Seo = e ie ote Innertren Unit mm | @ ] SHT 1/1 | Scale 1:1 1 T 2 T 3 T 4 a 5 T 6 T 7 T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 6 7 1 1 8 T Rev. [Customer Rev.| Description [Date | Reviser_[ Checked 70 [Terpory drawing woe | sonainis | Maverg | svchel A 8 76.20 S40-727827-00D-A0 Listes DB-700/800 .5W CL-A/B Rating 100-240V~, 50/60Hz, 2A mt Model CS40-734834-000-A0 Rev 1.0 12/2020 e ws FCC ID :NVRDPSAB1000.78 Separate Label Attachment 2
Conforms to UL STD. 62368-1 Certified to CSA STD. Barcode Format: Code 39 or 128. r Scale size to fit as needed WESTELL |
E
| Notes. F 1, Quality of the material : White Polyester (J WORLD CO LTD JW-916 oF JW-019) 2, Adhesive specification : UL969 (Permanent adhesive) 3, Printed color ; Black (Exclude Designated Parts) 4 4, No text smudging, erasing, etc. 5. Quantity : 1EA G6 Design And Process DWG.Name |PSR Label-7 re Change: Public Safety Repeater 4 He Chnges Intel es. Design [Mavng Rene Cee ee ceey | Be: Oesion [CHLee TT-OWE No. | 11088001-P007
# The Manufacturer After *
Sample Approval Without Approve |$.0.Se0 7 Whiten Authority From Innertroen INNERTRON Unit mm | @ Ep] SHT 1/1 | Seale 1:1 3 T 4 5 T 6 T 7 T 7B 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 WESTELL RoHS Compliant el Ll 2 lL 3 I 4 \ 5 L 6 l 7 l 8 T Rev. [Customer Rev. Description Date | Reviser | Checked 70 3 Tercera drwing we | Soins | Mayang | _sycrer A 8 76.20
c CS40-727827-00D-BO Listed DB-700/800 .56W CL-B Rating 100-240V~, 50/60Hz, 2A
=I Model : CS40-734834-00D-A0 Rev-1.0 12/2020 us 5 fe Label ateeh o FCC ID :NVRDPSA81090-78 eparate Label acnmen
= Intertek D | 5018566 nm Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62 Barcode Format: Code 39 or 128. of rc Scale size to fit as needed WESTELL 1 BNotes,
' 1. Quality of the material : White Polyester (J WORLD CO LTD JW-016 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) J 4. No text smudging, erasing, etc. 5. Quantity : 1B 6 Design And Process DWGName PSR Label-8 re Changs: Public Safety Repeater
| No Cha In Material sons oat Mec. Design |M.R.Yang Pincies shat Be Mose By | G2. Design |CHLee IT-DWG No. | 171098001-Po08 4 The Manufacturer After -
Samale Approval Without Approve |S.0.Se0 Ti tren n Authonty From INNERTRON Unit mm | @ ep] SHT 1/1 | Seale 1:1 ( nnertren 1 T 2 T 3 qr 4 5 T 6 T a T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 6 Ll 7 l a T Rev. [Customer Rev. Description Date | Reviser | Checked GJ Tereerey dawingne | Maine | Maverg | sychel 76.20 38.10 CS40-727000-00D-A0 Listed SB-700 .5W CL-A/B Rating 100-240V~, 50/60Hz, 2A Model CS40-734834-000-A0 Rev 1.0 12/2020 e oe FCC ID : NVRDPSA81090-78 5018566 Separate Label Attachment o Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62 Barcode Format: Code 39 or 128. o r Scale size to fit as needed WESTELL a al Notes. F 1, Quality of the material : White Polyester (J WORLD CO LTO JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts)
| 4. No text smudging, erasing, ete. 5. Quantity : 164. G Design And Process DWG.Name | PSR Label-9 Tm Change Public Safety Repeater
| No Char In Material 5 J Design Gr Process Which | M&t: Desin | MAYang sercee Grol Be Mose By | Be: Design |CHLee IT-DWG No, | 1T1098001-Po09 H The Manufacturer After . Sample Approval Without Approve | $.D.Se0 =
daten Auenty From Innertren INNERTRON Unit mm | @ <p] SHT 1/1 | Scale 1 3 4 a 5 T T 7 1 8 8 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RolS Compliant WESTELL 6 I 7 8 38.10 T Rev. [Outarar Rev]
Description Date Reviser_| Checked Temporary drawing Hive BORON SchoL 76.20 CS40-727000-00D-B0 Listed SB-700 .5W CL-B Rating 100-240V~, 50/60Hz, 24 Model : C$40-734834-000-A0 Rev: 1.0 12/2020 e ve FCC ID : NVROPSA81090-78 Intertek 5018566 Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 6236:
Separate Label Attachment Barcode Format: Code 39 or 128. Scale size to fit as needed 5 e 7 WiNotes. F 1. Quality of the material : White Polyester (J WORLD CO LTO JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color: Black (Exclude Designated Parts) 4 4. No text smudging, erasing, etc. 5. Quantity ; 164, G ig Design And Process DWG.Name | PSR Label-10 Chane Public Safety Repeater 4 No Changes In Material Mec. Design |M.R.Yang ny Eee Design Or Process Which Form, Fi a eS py | He Design |[CHLee IT-DWG No, | 1T1098001-P010 4 The Manufacturer After =
Sample Approval Without Approve | $.0.Se0 7 eB wus Aaa Fre innertren INNERTRON unit mm | @ ep] sur 171 | Seale 1:1 3 T 4 a 5 T 6 T 7 T 8 75 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant 2 1 WESTELL 3 I 4 | 5 L 6 Ll 7 l 8 v Rev. [Customer Rev. Description Date | Reviser | Checked
| Teneoray drawing we | Suarite | Maveng | _sychal A 3 76.20 _ c CS40-000827-00D-AO Listed SB-800 .5W CL-A/B Rating 100-240V~, 50/60Hz, 2A 4 Model : C$40-734834-000-A0_ Rev 1.0 12/2020 e we s fe (abe) Aitach o FCC ID : NVRDPSA81090-78 eparate Labe' achment
= Intertek
) 5018566
) Conforms to UL STD. 62368-1 Certified to CSA STD. C222 No. 6236 Barcode Format: Code 39 or 128. o cr Scale size to fit as needed WESTELL E
| WNotes. F 1, Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-019) 2. Adhesive specification ; UL969 (Permanent adhesive) 3, Printed color : Black (Exclude Designated Parts) J 4, No text smudging, erasing, etc. 5. Quantity : 18A G Design And Process DWG.Name | PSR Label-11 re Corer: Public Safety Repeater 4 No In Material +
Erangre in| ee Mec. Design | M.R.Yang Funcion Srl Be Wade By |: Desion |CiHLee 1-9WG No. |1T1098001-P011 H The Manufacturer After *
Sample Approval Without Appr $.D.Se0 =F Whitten Authority From we In nert ren INNERTRON Unit mm | @ =} | SHT 1/1 | Scale 4:1 1 T 2 3 T 4 a 5 T 6 T 7 T @ AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 8 3 i 4 | 5 1 6 i vi L t Rev. [Customer Rev.| Description Date Reviser_| Checked 7 5 Tergoray drawing une | Bwana | Mavarg | _Schel A B 76.20 =
CS40-000827-00D-BO Listed SB-800 .6W CL-B Rating 100-240V~, 50/60Hz, 2A
| Model - CS40-734834-000-A0 Rev-1.0 12/2020 us FCC ID: NVROPSA81080-78 Separate Label Attachment
= intertek D 5018566 Conforms to UL STO. 62368-1 Certified to CSA STD. C22.2 No. 6236 Barcode Format: Code 39 or 128. o r Scale size to fit as needed WESTELL |
E
| BNotes. F 1, Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed colar : Black (Exclude Designated Parts) 4 4, No text smudging, erasing, etc. 5. Quantity : 164 6 Design And Process DWG.Name | PSR Label-12 Tee Change Public Safe r 7 No In Material Mec. Design [MR.Yang ublic Safety Repeate:
Design Or Process Which Function Stal Bo Mave By Be. Design |CH.lee IT-DWG No. | 1T1098001-P012 4 The Manufacturer After =
Sample Approval Without Approve $.D.Se0 =
Wrtten Authonty From innertran INNERTRON Unit mm | @ ee] sHT 1/1 | Seale tt 3 T 4 5 T T z T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL DB-700/800 1W CL-A/B Rating 100-240V~, 50/60Hz, 2A Model CS40-734834-00D-A0_ Rev-1.0 12/2020 Le bd FCC ID: NVRDPSAB1090-78 l 3 l 4 | 5 I 6 L 7 l 8 T Rev. [Customar Re Description Date | Reviser_| Checked
| Teneoray rowing wave | TaaoTIa | MaYerg | svchel 76.20 . CS40-730830-00D-AO pee Separate Label Attachment
= Intertek D oO 5018566
~ Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 6236 Barcode Format: Code 39 or 128. b r Scale size to fit as needed WESTELL ul E 7 BNotes. F 1, Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-019) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) 7 4, No text smudging, erasing. ete. 5. Quantity : 1BA G Design And Process DWG.Name |PSR Label-xx ri cose Public Safety Repeater
| No Changes In Material Mec. Design |M.R:Yang ublic Safety Repe Design Or Process Which Pencies Shan Be Maze By | 8-Design |CHLee \T-0WG No. | 171098001-Pox H The Manufacturer Aer =
Sample Approval Without Approve | S.0.Se0
= Innertren INNERTRON Unit mm | @ ey] SHT 1/1 | Seale t:1 1 T 3 T 4 a 5 T 6 T 7 T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 WESTELL RoHS Compliant I 2 I 3 I 4 | 5 6 il 7 Ll 8 T Rev. [Customer Rov. Description Date_[ Reviser_| Checked 5 : Tenporey draning Have peeariis | Maven | svchei 76.20 c CS40-730000-00D-AO Listed SB-700 1W CL-A/B Rating 100-240V~, 50/60Hz, 2A Model : CS40-734834-000-A0 Rev 1.0 12/2020 e bad Separate Label Attachment FCC ID : NVRDPSA81090-78 2 Intertek 2 5018566 mn Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62:
Barcode Format: Code 39 or 128. Scale size to fit as needed o r _ WESTELL 5 MNotes, 1. Quality of the material : White Polyester (J WORLD CO LTO JW-916 or JW-019) 2, Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) 4, No text smudging, erasing, etc. 5. Quantity : 164 Ss ie Design And Process DWG.Name |PSR Label-xx "
Public Safety Repeater 4 No Changes In Material Mee. Design | MARY:
Design Or Process Which ie Pees |e Will Effect Form, Fit Or scan Made By | 6: Design |C-H.lee IT-DWG No. | 1T1098001-POxx i The Manufacturer After =
Sample Approval Without Approve | S.D.Seo ae inenraon Innertren INNERTRON Unit mm | @ ep] SHT 1/1 | Seale 1:1 1 T 2 T 3 ara 5 T $ T 7 T a 3 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 2 3 L 4 5 i 6 L - l 8 T Rev. [Cumamar Rav. Description Date | Reviser_| Checked FO S Temporary dawing wwe | zororiie | Mayan | Schot A 8 76.20 _ c CS40-000830-00D-A0 pised SB-800 1W CL-A/B Rating 100-240V~, 50/60Hz, 24 of Model CS40-734834-000-A0 Rev:10 12/2020 we 5 rallabeliAtach f Oo FCC ID :NVRDPSA81090-78 er eparate Labe acnmen
= Intertek
) 5018566 on) Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62 Barcode Format: Code 39 or 128. o r Scale size to fit as needed e
| WNotes. fe 1. Quality of the material : White Polyester (J WORLD CO LTO JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) al 4, No text smudging, erasing, etc. 5. Quantity : 124 6 Design And Process DWG.Name | PSR Label-x ne Change "
at ie a Ohskaret Moc!Betin|| Winvene Public Safety Repeater Design Or Process Which Foncign So Bn Mace py | He: Design [CHlee IT-DWG No, | IT1098001-POxx 4 te Lnpeeppred es Approval Without prove |S.0.Se0 =
Soe aay ree innertren INNERTRON Unit mm | @ eS] SHT 1/1 | Scale 1:1 2 3 T 4 5 6 T t T 8 AS 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 7 l 8 Description Date | Reviser_[ Checked 7 Temporary drawing eve poate | Mmyesg | svchol 76.20 38.10 CS40-730830-00D-BO Listed DB-700/800 1W CL-B Rating 100-240V-~, 50/60Hz, 2A Model : CS40-734834-000-A0_ Rev 1.0 12/2020 e us FCC ID : NVRDPSA81090-78 5018566 i Separate Label Attachment o Conforms to UL STD. 62368-1 Certified to CSA STD. C222 No. 2:
Barcode Format: Code 39 or 128. o cr Scale size to fit as needed WESTELL E 7 Notes. F 1. Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts) J 4. No text smudging, erasing, etc. 5. Quantity : 1EA G Design And Process. DWG.Name | PSR Label- ree Change Public Safety Repeater a No Changes In Material Mec. Desi r Design Or Process Which ee: Deion: | MeRavang fe , Fit Funcion Stat Be Mase By | 4e. Design |CH.lee IT-OWG No. | 1T1098001-POx 4 The Manufacturer After =
Sample Approval Without Approve | $.0,Se0 <7 Wen try ren Innertren INNERTRON Unit mm | @ <p] SHT 1/1 | Scale 1:1 7 T 7 a 5 T T 7 T 8 a5 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 RoHS Compliant WESTELL 7 Description Date Reviser Checked v Rev. [Customer Rev. PO Temporsy arawing hive pean MRS SY chet 76.20 CS40-730000-00D-B0 Listed SB-700 1W CL-B Rating 100-240V~, 50/60Hz, 2A Model CS40-734834-000-A0 Rev: 1.0 12/2020 2
: Separate Label Attachment 2 FCC ID : NVRDPSA81090-78 i D 2 5018566 Conforms to UL STD. 62368-1 Certified to CSA STD. C22.2 No. 62:
Barcode Format: Code 39 or 128. o W... r __| Scale size to fit as needed WESTELL
E 1 BNotes, F 1. Quality of the material : White Polyester (J WORLD CO LTD JW-916 or JW-919) 2. Adhesive specification : UL969 (Permanent adhesive) 3. Printed color : Black (Exclude Designated Parts)
| 4. No text smudging, erasing, ete. 5, Quantity : 164. 6 Design And Process DWGName |PSR Label-vcx ia Chang i te gen wait | we. Onan [waveng Public Safety Repeater Will Effect Form, Fit Or Function Shall Be Made By | "@ Design IT-DWG No. | 1T1098001-POxx H The Manufacturer After *
Sample Approval Without Approve >
Wnt y INMERTRON Unit mm | @ ep] SHT 1/1 | Scale 1:1 (Innertren 3 T 4 a 5 T e T 7 T 2 AS Signature: oe Date: 12/4/2020 Name: d6seph Gage Title: Compliance Engineer Company: _Westell, Inc. 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500 2 3 4 I 5 | 6 I 7 I 8 I Fisy, [Custerres Ra. Demure Os Raves | Checked RO = Temporary drawing issue zoeonsa2 | _CHiee CHlee A 8 c 44,45 WARNING. This is NOT a CONSUMER D device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS You MUST have an FCC LICENSE or express consent of the FCC Licensee to operate this wT, device. Unauthorized use may result in Ke) significant forfeiture penalties, Including N E penalties in excess of $100,000 for each Continuing violation F G Nemes: Umessiiresuise-speaied Design And Process 55 [Outline Drawing Change 4 1. J WORLD CO LTD JW-916 or JW-919 No Changes in Material [ [cutee FCC WARNING LABEL 2. Print Color - Black Design Or Process Which will Effect Form, Fit Or a Function Shall Be Made By | s CL Hy The Manufacturer After =
Sample Approval Without = |8:DSe0 *
Written Authority From Raed nea Sas |e all ( innertron 4 2 3 4 5 6 T 7 I 8 AO compliant 2 3 4 | 5 | 6 I 7 I 8 1 Fisy, [Cuatornes Rev. Deweyan Osi Revce Necked RO : Temporary drawing ue | 20200902 | cHlee | CHlee A A B B 50,8 Part 90 Signal Boosters: THIS 1S A 90.219 CLASS B DEVICE:
WARNING: This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC t LICENSE or express consent of an FCC Licensee to operate i this device. You MUST register class B signal boosters (as lO defined in 47 CFR 90.219) online at N E www.fcc.gov/signal-boosters/registration. Unauthorized E use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation F F G G NOTE : Unless otherwise specified Design And Process Outline Drawing of Change:
4 1. J WORLD CO LTD JW-916 or JW-919 No Changes in Material | |CHttee FCC PART 90 LABEL 2. Print Color - Black Design Or Process Which Will Effect Form, Fit Or Sf Function Shall Be Made By | s CL H The Manufacturer After H Sample Approval Without oe |S.DSe0 hs Written Authority From INET ben Sea |e aae ( innertron 2 3 4 5 6 I 7 I 8 AO FCC WARNING LABEL FCC PART 90 LABEL ETL LABEL e 80-TN00LNH-SM ) (Dy eo aoint-oM Ie)
1 2 | Agent Authorization | Cover Letter(s) | 285.82 KiB | January 26 2021 |
WESTELL Agent Authorization Company: Westel,! Inc. Address: 750 North Commons Drive, Aurora, IL 60504 Product Name: Public Safety Repeater Model Number(s): CS40-734834-00D-A0, CS40-734000-00D-A0, CS40-000834-00D-A0, CS40-730830-00D-
AO, CS40-730000-00D-A0, CS40-000830-00D-A0, CS40-727827-00D-A0, CS40-727000-00D-A0, CS40-
000827-00D-A0, CS40-000827-00D-A0, CS40-734834-00D-B0, CS40-734000-00D-B0, CS40-000834-00D-
BO, CS40-730830-00D-B0, CS40-730000-00D-B0, CS40-000830-00D-B0, CS40-727827-00D-BO, CS40-
727000-00D-B0, CS40-000827-00D-BO Product Description: 700/800MHZ Class A/B Bi-Directional Amplifier We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature: S Date: 12/4/2020 Name:
Title: Compliance Engineer Company: Westell, Inc. 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500
1 2 | Declaration of Compliance | Cover Letter(s) | 213.42 KiB | January 26 2021 |
WESTELL Date: December 16, 2020 Federal Communications Commission Equipment Authorization Division 7435 Oakland Mills Road Columbia, MD 21046 USA Attn: OET Dept. Subject: Supplier's Declaration of Compliance To Whom It May Concern:
We hereby attest to the fact that we have applied the Supplier's Declaration of Conformity (SDoC) for a Class A Digital device portion of this composite filing. The requirements identified in KDB 896810 and 47CFR 2.948(b) have been followed. A test report has been issued by ESTECH Co., Ltd( 140-16, Eongmalli-ro, Majang-myeon, Icheon-si, Gyeonggi-do, Korea) and can be identified by report number : ESTCFC2012-
004. Sincerely, Westell Inc. Address:
Westell 750 North Commons Drive Aurora, IL 60504 USA Signature: Lg a Name and Job Title:
Joseph Gage Compliance Engineer E-mail: jgage@westell.com Tel 630-375-4724 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500
1 2 | attestation letter | Attestation Statements | 281.55 KiB | January 26 2021 |
Date: February 5, 2020 KDB 935210 D02 Section V (G) Attestation NVRDPSA81090-78 FEDERAL COMMUNICATIONS COMMISSIONS Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 RE: FCC ID: NVRPS71090E-PS78 To Whom It May Concern:
In accordance with the Federal Communications Commission Office of Engineering and Technology Laboratory Division document titled SIGNAL BOOSTERS BASIC CERTIFICATION REQUIREMENTS, dated April 8, 2016, Westell Inc affirms it will abide by the requirements of section V, titled I PART 90 SIGNAL BOOSTER SPECIFIC REQUIREMENTS, item (G), concerning warning label messages. This letter is to attest that the warning labels, shown above, which are required to be present on the unit chassis by item G of the aforementioned requirement document, will be also shown in online and point-of-sale marketing materials and on outside packaging of device. Thank you for your attention to this matter. Sincerely Joe Gage Compliance Engineer ______________________________________________________________________________________________________________________________________________________________________________________________ 750 North Commons Drive Aurora, Illinois 60504 www.westell.com
1 2 | request for confidentiality Part 20 | Cover Letter(s) | 331.93 KiB | January 26 2021 |
WESTELL Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 12/3/2020 Subject; Request for Confidentiality FCC ID:
To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market.
&] Schematic Diagram x] Block Diagram xd Parts List Operational Description Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);
Z] External Photos Test Setup Photos Internal Photos User Manual
(_] For 45 days, pursuant to Public Notice DA 04-1705. OR PK For 180 days pursuant to KDB 726920 DO1. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, Signature: Cre S822 |
we a Name: Joseph Gage Title Compliance Engineer 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500
1 2 | request for confidentiality Part | Cover Letter(s) | 333.19 KiB | January 26 2021 |
WESTELL Office of Engineering Technology Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 USA Date: 12/3/2020 Subject; Request for Confidentiality FCC ID:
To Whom It May Concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. These documents contain detailed system and equipment descriptions and are considered as proprietary information in operation of the equipment. The public disclosure of these documents might be harmful to our company and would give competitors an unfair advantage in the market. KK] Schematic Diagram
<| Block Diagram bef Parts List
[= Operational Description ly} Tune-up Procedure In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);
& External Photos kd Test Setup Photos
[Lf Internal Photos
{4} User Manual _] For 45 days, pursuant to Public Notice DA 04-1705. OR
(4 For 180 days pursuant to KDB 726920 DO1. It is our understanding that all measurement test reports, FCC ID label format and correspondence during the certification review process cannot be granted as confidential documents and this information will be available for public review once the grant of equipment authorization is issued. Sincerely, . Ce ae Signature: _ ote pe e Name: Joseph Gage Title Compliance Engineer 750 North Commons Drive Aurora, IL 60504 USA
(630) 898-2500
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2021-01-26 | 862 ~ 869 | B2I - Part 20 Industrial Booster (CMRS) | Original Equipment |
2 | 851 ~ 862 | B9B - Part 90 Class B Industrial Booster (non-SMR) |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2021-01-26
|
||||
1 2 | Applicant's complete, legal business name |
Westell, Inc.
|
||||
1 2 | FCC Registration Number (FRN) |
0010374171
|
||||
1 2 | Physical Address |
750 North Commons Drive
|
||||
1 2 |
Aurora, IL
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
c******@micomlabs.com
|
||||
1 2 | TCB Scope |
B1: Commercial mobile radio services equipment in the following 47 CFR Parts 20, 22 (cellular), 24,25 (below 3 GHz) & 27
|
||||
1 2 |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
|||||
app s | FCC ID | |||||
1 2 | Grantee Code |
NVR
|
||||
1 2 | Equipment Product Code |
DPSA81090-78
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
J****** K****** G********
|
||||
1 2 | Title |
Compliance Engineer
|
||||
1 2 | Telephone Number |
630-3********
|
||||
1 2 | Fax Number |
630-3********
|
||||
1 2 |
j******@westell.com
|
|||||
app s | Technical Contact | |||||
1 2 | Firm Name |
Westell, Inc.
|
||||
1 2 | Physical Address |
United States
|
||||
1 2 |
j******@westell.com
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 2 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 07/25/2021 | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | B2I - Part 20 Industrial Booster (CMRS) | ||||
1 2 | B9B - Part 90 Class B Industrial Booster (non-SMR) | |||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | 700/800 MHZ DUAL BAND INDUSTRIAL BOOSTER | ||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Original Equipment | ||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | Yes | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | In-Building DAS Industrial Booster. Class B signal booster. Power output is conducted. The intended use is for industrial/commercial use and will not be sold to the general public. Professional installation is required. The antenna(s) used for this transmitter are to be fixed-mounted on indoor structures, and may not have gain exceeding 8.5 dBi. The antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not transmit simultaneously with any other antenna or transmitter. Users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
ESTECH Co., Ltd.
|
||||
1 2 | Name |
Y****** J******
|
||||
1 2 | Telephone Number |
82-31********
|
||||
1 2 | Fax Number |
82-31********
|
||||
1 2 |
j******@estech.co.kr
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 90S | 817 | 824 | 0.5 | GXW | |||||||||||||||||||||||||||||||||||
1 | 2 | 90S | 817 | 824 | 0.5 | G7W | |||||||||||||||||||||||||||||||||||
1 | 3 | 90S | 817 | 824 | 0.5 | F9W | |||||||||||||||||||||||||||||||||||
1 | 4 | 90S | 862 | 869 | 2.5 | GXW | |||||||||||||||||||||||||||||||||||
1 | 5 | 90S | 862 | 869 | 2.5 | G7W | |||||||||||||||||||||||||||||||||||
1 | 6 | 90S | 862 | 869 | 2.5 | F9W | |||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 9 | 758 | 768 | 2.5 | F1E | |||||||||||||||||||||||||||||||||||
2 | 2 | 9 | 758 | 768 | 2.5 | F1D | |||||||||||||||||||||||||||||||||||
2 | 3 | 9 | 758 | 768 | 2.5 | F3E | |||||||||||||||||||||||||||||||||||
2 | 4 | 9 | 758 | 768 | 2.5 | F2D | |||||||||||||||||||||||||||||||||||
2 | 5 | 9 | 758 | 768 | 2.5 | F9W | |||||||||||||||||||||||||||||||||||
2 | 6 | 9 | 758 | 768 | 2.5 | G7D | |||||||||||||||||||||||||||||||||||
2 | 7 | 9 | 758 | 768 | 2.5 | D7W | |||||||||||||||||||||||||||||||||||
2 | 8 | 9 | 769 | 775 | 2.5 | F1E | |||||||||||||||||||||||||||||||||||
2 | 9 | 9 | 769 | 775 | 2.5 | F1D | |||||||||||||||||||||||||||||||||||
2 | 1 | 9 | 769 | 775 | 2.5 | F3E | |||||||||||||||||||||||||||||||||||
2 | 11 | 9 | 769 | 775 | 2.5 | F2D | |||||||||||||||||||||||||||||||||||
2 | 12 | 9 | 788 | 798 | 0.5 | F1E | |||||||||||||||||||||||||||||||||||
2 | 13 | 9 | 788 | 798 | 0.5 | F1D | |||||||||||||||||||||||||||||||||||
2 | 14 | 9 | 788 | 798 | 0.5 | F3E | |||||||||||||||||||||||||||||||||||
2 | 15 | 9 | 788 | 798 | 0.5 | F2D | |||||||||||||||||||||||||||||||||||
2 | 16 | 9 | 788 | 798 | 0.5 | F9W | |||||||||||||||||||||||||||||||||||
2 | 17 | 9 | 788 | 798 | 0.5 | G7D | |||||||||||||||||||||||||||||||||||
2 | 18 | 9 | 788 | 798 | 0.5 | D7W |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC