| all | frequencies |
|
exhibits | applications |
|---|---|---|---|---|
| manual |
| app s | submitted / available | |||||||
|---|---|---|---|---|---|---|---|---|
| 1 |
|
User Manual | Users Manual | 3.42 MiB | September 02 2017 | |||
| 1 | Cover Letter(s) | September 02 2017 | ||||||
| 1 | External Photos | September 02 2017 | ||||||
| 1 | Internal Photos | September 02 2017 / August 08 2017 | ||||||
| 1 | ID Label/Location Info | September 02 2017 | ||||||
| 1 | ID Label/Location Info | September 02 2017 | ||||||
| 1 | ID Label/Location Info | September 02 2017 | ||||||
| 1 | Cover Letter(s) | September 02 2017 | ||||||
| 1 | RF Exposure Info | September 02 2017 | ||||||
| 1 | RF Exposure Info | September 02 2017 | ||||||
| 1 | Test Report | September 02 2017 | ||||||
| 1 | Test Report | September 02 2017 | ||||||
| 1 | Test Setup Photos | September 02 2017 | ||||||
| 1 | Test Setup Photos | September 02 2017 |
| 1 | User Manual | Users Manual | 3.42 MiB | September 02 2017 |
5689 PS71090 Product Manual January 2017, Rev A PS71090 2W Public Safety Signal Booster Users Guide P R O D U C T M A N U A L 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 1 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A DISCLAIMER All information and statements contained herein are accurate to the best of Westell Technologies knowledge. Westell makes no warranty with respect there to, including without limitation any results that may be obtained from the products described herein or the infringement by such products of any property rights of any persons. Use or application of such information or statements is at the users sole risk, without any liability on the part of Westell. Nothing herein shall be construed as license or recommendation for use, which infringes upon any propriety rights of any person. Product material and specifications are subject to change without notice. Westell standard terms of sale and the specific terms of any particular sale apply. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 2 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Table of Contents PREFACE................................................................................................................................... 7 Purpose ............................................................................................................................................................. 7 Scope................................................................................................................................................................. 7 Audience ........................................................................................................................................................... 7 Document Organization ................................................................................................................................ 8 References ........................................................................................................................................................ 9 Document Conventions ................................................................................................................................. 9 Safety Notices ............................................................................................................................................... 10 Technical Support ......................................................................................................................................... 10 Acronyms and Abbreviations ..................................................................................................................... 10 Copyright and Trademark Acknowledgements ...................................................................................... 10 1 GENERAL INFORMATION ............................................................................................... 11 1.1 Document Purpose and Intended Users ........................................................................................... 11 1.2 Application .............................................................................................................................................. 11 1.2.1 Product Registration Information .................................................................................................................. 11 1.3 Safety Guidelines .................................................................................................................................... 12 1.3.1 Important Safety Information .............................................................................................................................. 13 1.4 FCC Part 90 Signal Boosters ................................................................................................................ 13 1.5 FCC Contact Information ...................................................................................................................... 14 2 PRODUCT OVERVIEW ...................................................................................................................... 15 2.1 Product Information .............................................................................................................................. 15 2.2 Product Features .................................................................................................................................... 15 2.3 Included Accessories ......................................................................................................................... 16 2.4 Optional Accessories ............................................................................................................................. 16 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 3 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 3 PRODUCT SPECIFICATION .............................................................................................. 17 3.1 RF Specifications .................................................................................................................................... 17 3.2 Power Specification ............................................................................................................................... 17 3.3 Mechanical Specification ...................................................................................................................... 18 3.4 Environmental Specification ................................................................................................................ 18 3.5 GUI Items ................................................................................................................................................. 19 3.6 Alarm Status ........................................................................................................................................... 20 3.7 Alarm Relay ............................................................................................................................................. 21 4 PRODUCT APPEARANCE................................................................................................. 22 4.1 External Configuration .......................................................................................................................... 22 5 INSTALLATION GUIDELINES ........................................................................................... 23 5.1 Important Installation Guidelines ....................................................................................................... 23 5.2 Donor Antenna Installation Guidelines ............................................................................................. 24 5.3 Indoor Antenna Installation Guidelines ............................................................................................. 24 5.4 Mounting the Signal Booster .............................................................................................................. 25 5.5 Verifying the Physical System Setup .................................................................................................. 26 5.6 Controlling the Signal Booster ............................................................................................................ 26 5.7 Connecting to the Alarm Relay Panel ................................................................................................ 27 5.8 Connecting the Power Cable ................................................................................................................ 29 5.9 Connecting the Battery Back-up Cable .................................................................................... 31 6 SYSTEM OPERATION ....................................................................................................... 32 6.1 Operating the Program ......................................................................................................................... 32 6.2 Status........................................................................................................................................................ 34 6.3 Control ..................................................................................................................................................... 38 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 4 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 7.0 INSTALLING SOFTWARE INSTALLATION ................................................................. 43 7.1 Upgrading the Firmware ...................................................................................................................... 46 7.2 IP Change ................................................................................................................................................ 48 7.2.1 IP Change Window .......................................................................................................................................................... 48 7.2.2 Static IP Setting .................................................................................................................................. 49 7.2.3 DHCP IP Setting .................................................................................................................................. 49 APPENDIX A IMPORTANT PRODUCT INFORMATION .............................................. 50 A.1 Registration Number............................................................................................................................. 50 A.2 UL .............................................................................................................................................................. 50 APPENDIX B ACRONYMS AND ABBREVIATIONS ...................................................... 51 TABLE OF FIGURES Figure 1-1: Product Registration..................................................................................................... 11 Figure 4-1: External Product Configuration.......................................................................................... 22 Figure 5-1: Repeater Mounting Bracket Mounted on Repeater Rear.................................................. 25 Figure 5-3A: Ethernet Cable................................................................................................................. 26 Figure 5-3BA: Ethernet Connectors...................................................................................................... 26 Figure 5-4: Stripped Cable Conductors........................................................................................... 27 Figure 5-5: Alarm Relay 9 Position D-Sub Connector........................................................................... 27 Figure 5-6: Alarm Relay Cable Connected to Repeater........................................................................ 28 Figure 5-7: Remove the Power Connector Cap.................................................................................... 29 Figure 5-8: Connector Keys.................................................................................................................. 29 Figure 5-9: Power Cable Connected to Repeater........................................................................... 30 Figure 5-10: Power Cable Connected to Repeater............................................................................... 30 Figure 5-11: Battery Cable Connected to Repeater............................................................................. 30 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 5 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Figure 6-1: Status Mode....................................................................................................................... 34 Figure 6-2: Control Mode Page............................................................................... 38 Figure 6-3: Native to Destination Directory.......................................................................................... 43 Figure 6-4: Click Next to Begin Installation........................................................................................... 44 Figure 6-5: Installation Progress Window............................................................................................. 44 Figure 6-6: Installation Complete......................................................................................................... 45 Figure 7-1: Firmware Upgrade Progress Window showing File Open tab ........................................... 46 Figure 7-2: Firmware Version Check.................................................................................................. 46 Figure 7-3: Firmware Update Status.................................................................................................... 47 Figure 7-3: IP Settings........................................................................................................................... 48 Figure 7-4: IP Change WIndow............................................................................................................. 48 Figure 7-5: Static IP Address...................................................................................... 49 Figure 7-6: DHCP IP Address.............................................................................................................. 49 LIST OF TABLES Table P-1: Document Conventions........................................................................................................ 9 Table 2-1: Included Accessories........................................................................................................... 16 Table 2-2: Optional Accessories ...........................................................................................................16 Table 3-1: RF Specifications................................................................................................................. 17 Table 3-2: Power Specifications........................................................................................................... 17 Table 3-3: Mechanical Specifications................................................................................................... 18 Table 3-4: Environmental Specifications.............................................................................................. 18 Table 3-5: GUI Items............................................................................................................................. 19 Table 3-6: Alarm Status........................................................................................................................ 20 Table 3-7: Alarm Relay......................................................................................................................... 21 Table 5-1: Alarm Relay Connections..................................................................................................... 28 Table B-1: Acronyms and Abbreviations............................................................................................... 51 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 6 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Preface This Preface includes the following:
Purpose Scope Audience Document Organization References Document Conventions Safety Notices Technical Support Acronyms and Abbreviations Copyright and Trademark Acknowledgements Purpose This manual contains information and procedures for the operation of the Westell PS71090 Public Safety Signal Booster. Changes that occur after the publishing date may be incorporated by a complete manual revision or as additions. Scope Reference this manual when there is a need to add enhanced signal capability to a new or existing system, to monitor a system, make maintenance adjustments, or address alarms. Audience This manual is intended for installers and users who are familiar with similar types of equipment. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 7 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Document Organization This manual includes the following chapters:
Chapter 1: General Information Outlines the document purpose and intended users, application, product registration, safety guidelines, disclaimer and FCC Part 90, FCC Warning Labels. Chapter 2: Product Overview Provides product information, describes product features and lists accessories. Chapter 3: Product Specification Provides tables containing RF, power, mechanical and environmental specifications. Also provides information about GUI items, alarm status and alarm relay. Chapter 4: Product Appearance Provides physical specifications, photographs and information about the external and internal Signal Booster configuration. Chapter 5: Installation Guidelines Lists guidelines for installing the Signal Booster and antennas. Chapter 6: Software Installation Outlines the steps required to install the software. Chapter 7: System Operation Describes product operation, including how to open the communication port and describes the functions in the Status and Control pages. Appendix A: Important Product Information Provides the product registration number and internal power supply information. Appendix B: Acronyms and Abbreviations A table of acronyms and abbreviations and definitions for each. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 8 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A References FCC Part 90 Document Conventions Table P-1 lists the conventions used throughout this document. Table P-1: Document Conventions Convention Description DANGER!
Description of an imminent hazard that, if not avoided, may result in severe personal injury or death. Before you work on equipment, be aware of the hazards involved with electrical and RF circuitry and be familiar with standard practices for preventing accidents. WARNING!
Description of an imminent hazard that, if not avoided, may result in personal injury or serious equipment damage. CAUTION Description of a conditions or practice that could cause damage to equipment or property. Communicates information that is crucial to preventing loss of data or damage to hardware or software, and actions that could result in equipment failure. IMPORTANT Additional important information that the user must be aware of, but is not related to a hazard. NOTE Bold Click Additional information that is beneficial for the user to know, but is not related to a hazard. Bold text indicates an action or provides emphasis. Instructs the user to press the primary (typically left) mouse button while the pointer is over the specified location. Right-click Instructs the user to press the secondary (typically right) mouse button while the pointer is over the specified location. Double-click Instructs the user to press the primary (typically left) mouse button twice, rapidly, while the pointer is over the specified location. Select Enter
>
Instructs the user to perform a selection on the screen by clicking an active object. Instructs the user to type text using the keyboard. Indicates a level in a menu. For example, Start>Programs prompts the user to click on Start, then locate and click Programs under the Start menu. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 9 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Safety Notices This general safety information applies to both operating and service personnel. Specific warnings and cautions are located in other parts of this manual where they apply and may not appear in this summary. Failure to comply with these precautions or specific warnings elsewhere in the manual violates the safety standards of design, manufacture, and intended use of equipment. Westell assumes no liability for the customers or users failure to comply with these requirements:
Explosive atmospheres - To avoid explosion or fire, do not operate this product in the presence of flammable gases or fumes. Lightning danger - Do not install or make adjustments to this unit during an electrical storm. WARNING!
Changes and Modifications not expressly approved by Westell can void your authority to operate this equipment under Federal Communications Commissions rules. Technical Support If you suspect a malfunction with this product or have a technical question, call your dealer or the Westell Support Line at: (603) 626-6677, Toll Free (USA) 1-877-844-4274, press option 2, and then option 1. Westell Support can also be reached via email at IBWsupport@westell.com. Acronyms and Abbreviations Refer to Appendix B for definitions of the acronyms and abbreviations used in this manual. Copyright and Trademark Acknowledgements The following products are referred to in this manual:
is a registered trademark of Westell Technologies, Inc. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 10 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 1 General Information 1.1 Document Purpose and Intended Users The purpose of this document is to provide a step-by-step procedure to help experienced technicians or engineers install and commission an in-building Passive Wireless Distributed Antenna System (DAS) using Westells PS71090 2W Public Safety Signal Booster. Follow the instructions in this guide to minimize risks associated with modifying a live system and preclude service interruptions. This document assumes the technician or engineer understands the basic principles and functionality involved with an RF Signal Booster and in-building wireless systems. This guide has been written to address the practical concerns of the installer. 1.2 Application Use this guide whenever there is a need to add enhanced signal capability to an existing system or when a Signal Booster is included in a new installation. 1.2.1 Product Registration Information The serial number is located on the label on the panel near the power connectors. Record this number in Figure 1-1. Retain this manual, along with proof of purchase, to serve as a permanent record of your purchase. Figure 1-1: Product Registration 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 11 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 1.3 Safety Guidelines The general safety information in this guideline applies to both operations and service personnel. Specific warnings and cautions are located in the applicable manual sections, but may not appear in this summary. Failure to comply with these precautions or specific warnings elsewhere in the manual violates safety standards of design, manufacture, and intended use of equipment. Westell assumes no liability for the customers failure to comply with these requirements:
Grounding: This Signal Booster is designed to operate at 110VAC @ 1.02A maximum current and must always be operated with the ground wire properly connected. Explosive atmospheres: To avoid explosion or fire, do not operate this product in the presence of flammable gases or fumes. Lightning danger: Do not install or adjust this unit during an electrical storm. No user-serviceable parts are inside the unit. Hazardous voltages are present when the cover is removed. Opening the chassis will void your warranty. If you suspect a malfunction with this product, call your dealer or Westells technical support line at 1.877.844.4274. CAUTION Turn the Signal Booster power off when connecting or disconnecting cables. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 12 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Important Safety Information 1.3.1 Antennas used for the purpose of radiating signals indoors are limited to a maximum gain of 3 dBi. Each antenna must be positioned to observe minimum separation requirements from all users and bystanders. The following guidelines must be used when considering separation distances:
Indoor antennas must be placed so that under normal conditions, personnel cannot come within 20 cm (~8 in) of any inside antenna. Adhering to this minimum separation will ensure that the employee or bystander cannot exceed RF exposures beyond the maximum permissible limit as defined by FCC Regulations section 1.1310 Limits for general population/uncontrolled exposure. Outdoor antenna must be positioned so that under normal conditions, personnel cannot approach closer than 120 cm (~4 ft.). A directional antenna having a maximum gain of 3.75 dBi is used, and precautions should be taken to prevent personnel from routinely passing through the main radiation beam at a distance closer than specified. 1.4 FCC Part 90 Signal Boosters WARNING!
THIS IS A 90.219 CLASS B DEVICE This is not a consumer device. It is designed for installation by FCC licensees and qualified installers. You must have an FCC license or express consent of an FCC Licensee to operate this device. You must register class B signal boosters (as defined in 47 CFR 90.219) online at www.fcc.gov/signal-boosters/registration. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. FCC Warning Labels The following labels will appear on the PS71090 Signal Booster in accordance with the FCC:
WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 13 of 51 FCC Label Placement on the PS71090:
PS71090 Product Manual January 2017, Rev A Top View 1.5 FCC Contact Information Federal Communications Commission 445 12th Street SW Washington, DC 20554 Phone: 1-888-225-5322 TTY: 1-888-835-5322 Fax: 1-866-418-0232 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 14 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 2 Product Overview 2.1 Product Information The PS71090 Signal Booster was developed for use in enclosed structures where signals from local public safety towers to operate mobile units is poor or unavailable. Adequate signal strength must be available outside the structure as a prerequisite to achieving in-building coverage. The device is connected to an external antenna, normally located on a roof, and to one or more internal antennas placed strategically throughout the area where wireless service is desired. The external antenna is typically directional, such as a Yagi or Panel antenna. Internal antennas are typically omnidirectional, although various other types may be used, depending on the coverage application. The Signal Booster amplifies both the uplink (mobile to base) and downlink (base to mobile) signals, thus facilitating communications to and from the intended wireless infrastructure. With a maximum total of 90 dB nominal gain on both the uplink and downlink, gain can be adjusted over a range from 60 dB to 90 dB in 1 dB steps. The Signal Booster is controlled using a computer connected to the RJ45 Female Network Connector labeled GUI. There are also LED indicators to indicate alarm status, OSC and power. Refer to Figure 4-1. 2.2 Product Features Easy installation Light and small Control using a Windows-based Graphical User Interface (GUI) and accessed by connecting a laptop or desktop computer to the 8P8C/RJ45 Female Network Connector labeled GUI User gain control Automatic level control Automatic shutdown function Oscillation protection Overdrive protection Under/over voltage protection Fault protection Alarm notification SNMP Persistent status and error information Battery Back-up Input 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 15 of 51 WESTELL.COM Included Accessories 2.3 Table 2-1 contains the items that are shipped with the PS71090 Public Safety Signal Booster. Table 2-1: Included Accessories Quantity Description PS71090 Product Manual January 2017, Rev A 1 1 1 1 1 5 5 AC Power Cable, 5 feet 10 inches DC Power Cable, 5 feet 10 inches Ethernet cable, 6 feet 1 inch Alarm Relay Serial Cable, 4 feet 9 inches USB Drive containing the User Manual and Software Mounting Screws Drywall Anchors 2.4 Optional Accessories A complete line of accessories is available from Westell. Check with your Westell distributor for any additional items needed. Some products that are suitable for most in-building needs are listed in Table 2-2. Table 2-2: Optional Accessories Directional couplers 6 dB 10 dB 15 dB 20 dB 30 dB ClearLink-DC6/340-2.7K/N Clearlink-DC10/340-2.7K/N Clearlink-DC15/340-2.7K/N Clearlink-DC20/340-2.7K/N Clearlink-DC30/340-2.7K/N Power dividers 2:1 3:1 4:1 Clearlink-SPD2/340-2.7K/N Clearlink-SPD3/340-2.7K/N Clearlink-SPD4/340-2.7K/N 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 16 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 3 Product Specification 3.1 RF Specifications Parameter Specification Note Table 3-1: RF Specifications Frequency Range UL DL 788~805 MHz 806~809 MHz Sub-Band1 806~816 MHz Sub-Band2 806~824 MHz Sub-Band3 758~775 MHz 851~854 MHz Sub-Band1 851~861 MHz Sub-Band2 851~869 MHz Sub-Band3 Each band, 700 & 800, are independently Controlled via the GUI Linear Output Power UL / DL
+33dBm Shared Across Bands Gain UL / DL 90dB (1.0dB) Gain Adjustment Range UL / DL 30dB1dB AGC Range UL / DL 25dB (1dB) Pass Band Ripple UL / DL 1.5dB Typ. (Peak-To-Peak 3dB) 3rd Order Intercept Point UL / DL
+42.5dBm Input VSWR UL / DL
< 2:1 Maximum Input No damage Power UL / DL
+10dBm Propagation Delay UL / DL 4 Max. Noise Figure UL 5dB Typ. 6.5dB Max. Input / Output Impedance UL / DL 50 Ohms 3.2 Power Specification Table 3-2: Power Specifications 1dB step Parameter Specification Note Main Power Input Voltage 110 VAC Internal AC DC Power Supply 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 17 of 51 WESTELL.COM Battery Input Voltage 24 VDC to 30 VDC External Battery Power Supply Power Connector Power Consumption IEC320
<112W Max. AC/DC
<4 Amps Max. PS71090 Product Manual January 2017, Rev A 3.3 Mechanical Specification Table 3-3: Mechanical Specifications Parameter Specification Note Size 17.7 x 14.1 x 4.7 in L x H x D Link/Service Antenna Ports 4.3-10 type (female) AC Power In DC(Battery) Power In AC cord DC cord Connectors Frame Ground Two-Lug ground Ports RJ-45 Ethernet-1 (10/100 Base-T) GUI Interface RJ-45 Ethernet-2 (10/100 Base-T) SNMP Interface 9P D-SUB, female Alarm Relay Interface Wall-Mount with 4 holes 2 holes in each side Key Lock Two-Key Lock Natural Convection Red color Paint Mounting Type Enclosure Lock Heat Dissipation Finish 3.4 Environmental Specification Table 3-4: Environmental Specifications Parameter Specification Note Operating Temperature
-30C ~ +50C (ambient)
-22F ~ +122F Storage Temperature
-40C ~ +60C (ambient)
-40 F to +140 F Operating Humidity 5% ~ 95%
Environmental IP-65, NEMA 4 Compliance WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 18 of 51 PS71090 Product Manual January 2017, Rev A 3.5 GUI Items Parameter Specification Note Table 3-5: GUI Items UL/DL Output Readings 11dBm to 36dBm Alarm Readout Displays UL/DL Shutdown Setting PLL LD(Lock Detector), Isolation, UL/DL shutdown, DC Fail, Relay Status, UL/DL VSWR, Manual Amp 29dBm to 36dBm UL/DL Gain Setting 0dB to 30dB Reads and displays the UL/DL output power Displays alarm status Use to set the peak power
(shutdown level) Used to set the UL/DL system gain. System Location Display PS71090 PS-SMR700/800 Company, Address, City, State, Contact Displays the Signal Booster name and information. Control Send All Control Page Settings Used to save settings in the Control page. Isolation VSWR Quit Settable to 0db -or- 15dB. Adjustable from 1-30 None Closes the GUI page. Refer to Section 6 System Operation for more information about the GUI. WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 19 of 51 PS71090 Product Manual January 2017, Rev A 3.6 Alarm Status Table 3-6 Alarm Status Signal Booster Unit LED POWER x ISO x ALARM Condition/Troubleshooting x Power Supply is Out Of Order (inside Signal Booster) Blinking Blinking Blinking during isolation checking status GREEN Solid GREEN RED Off RED Solid Blinking GREEN RED Solid GREEN Solid GREEN Blinking GREEN Solid GREEN Solid GREEN GREEN Off RED Off RED Off RED Off RED Off RED Off RED Off RED Off RED RED Off RED Off RED Solid RED Normal condition at Power Up Insufficient distance (Isolation) exists between the DL and UL Antenna. You should turn off power and re-install the DL and UL antenna for right isolation distance. ( ALARM 1 , ALARM 2) This condition is Shut-Down Alarm. Received signal from cell tower is too strong (more than AGC range). Relocate DL Antenna to different location to reduce received signal ( ALARM 2 ) Blinking This condition is PLL Lock Detected Fail Alarm. RED
( ALARM 1 , ALARM 2) Off RED Solid RED Solid RED Solid RED AC failure ( ALARM 1 ) DL VSWR Alarm ( ALARM 3 ) UL VSWR Alarm ( ALARM 3 ) Manual Amp Alarm ( ALARM 2 ) Off Power Failure ( ALARM 1 ) RED Batt fail (Low , High), DC fail ALARM 1 : System component failure, and/or loss of power AC/DC (Pin 1,2,3) ALARM 2 : Active RF emitting device failure / PA failure (Pin 4,5,6) WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 20 of 51 ALARM 3 : Antenna failure Donor and Server VSWR Alarm (Pin7,8,9) PS71090 Product Manual January 2017, Rev A 3.7 Alarm Relay Table 3-7 Alarm Relay Shutdown Signal Relay Status Note Normally Open NO (pin 2) + CC (pin 3) PIN 1 NC, PIN 2 Normally Closed NC (pin 1) + CC (pin 3) NO, PIN 3 CC PIN 4 NC, PIN 5 NO, PIN 6 CC PIN 7 NC, PIN 8 NO, PIN 9 CC NOTE Either method in Table 3-7 would trigger the following alarms: Antenna Malfunction, PA Failure and Power Failure. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 21 of 51 WESTELL.COM 4 Product Appearance 4.1 External Configuration PS71090 Product Manual January 2017, Rev A Figure 4-1: External Product Configuration 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 22 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 5 Installation Guidelines 5.1 Important Installation Guidelines The PS71090 Signal Booster is designed for indoor use only. The PS71090 Signal Booster must be installed in a vertical orientation (i.e. Connectors on the bottom of the unit). Inadequate isolation between the outside and inside antennas may cause regenerative feedback in the system. This feedback can cause the amplifier to emit a continuous signal at maximum amplit ude, and, in some cases, interfere with normal operation of the donor site. Careful co nsideration of the layout and placement of the system is imperative to minimize this possibility and to minimize the amount of signal leaking from the building. Do not disassemble the Signal Booster. DANGER!
Refer to the 1.3 Safety Guidelines section for proper antenna selection and installation. To avoid serious injury, death and/or damage to the Signal Booster, do not install donor or server antennas near overhead power lines or high power components. Allow enough distance so that falling antennas would not come in contact with those components. Electric shock may occur if the Signal Booster is installed in close proximity to water. WARNING!
Amplifier or handset damage may occur if a handset is connected directly to the Signal Booster or to the coax that leads to the Signal Booster. The PS71090 Signal Booster must be connected to ground for protection. We recommend that installers do not wear jewelry or metal accessories when installing this Signal Booster. Do not place cables or tools that may damage the Signal Booster in close proximity to it. Check the installation site for hazardous conditions such as water-covered floors or badly worn or damaged cables prior to installation. Lifespan and performance of the Signal Booster may be reduced if the unit is operating outside its nominal temperature range. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 23 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A CAUTION Close proximity to the donor or server antennas with the Signal Booster in operation may expose users or installers to RF fields that exceed FCC limits for human exposure. Turn power to the Signal Booster off when connecting or disconnecting cables. 5.2 Donor Antenna Installation Guidelines Accurately determine the azimuth to the donor site. Obtain the donor site information and approval from the service provider/carrier. Ensure that the radiation path to the donor site is unobstructed. Mount the donor antenna at or toward the edge of the roof, in the direction of the donor site. Avoid having the RF signal from the donor pass above the location(s) of the service antennas. Normally, the service antennas are installed behind and below the donor antenna, as viewed from above. This approach helps avoid interference and feedback to and from the service antennas. Normally, mounting the donor antenna higher will allow a less obstructed path to the donor site. However, in high traffic metro areas, avoid mounting the donor antenna higher than necessary, as the quality of the donor signal may become less stable and it is more likely to encounter adjacent channel interference. When possible, shield the rear of a donor antenna by locating it so that any HVAC units and/or penthouse structures are behind the antenna, relative to the donor cell site location. 5.3 Indoor Antenna Installation Guidelines Use omnidirectional antennas (see section 2.4. Optional Accessories) indoors and locate them centrally with respect to the intended coverage area to minimize signal leakage to the outside. Only use directional antennas indoors in special cases when higher gain and directionality would be helpful and RF exposure limits will not be exceeded. To avoid Signal Booster uplink overload and gain limiting, mount the indoor antennas away from areas where mobile subscribers frequently use their phones, such as desks or dispatch areas. To determine the quantity and locations of indoor antennas, measure Received Signal Strength Indication (RSSI) using DM Tool software to determine areas of weak signals. These are the approximate areas where indoor antennas may be needed. Be aware that the signal from an indoor antenna, in most cases, can be expected to penetrate approximately two standard sheet rock walls to reach users. If the signal must travel through more than two walls, or if the walls are made of materials other than sheet rock, it may be necessary to split the available signal and add more antennas. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 24 of 51 WESTELL.COM 5.4 Mounting the Signal Booster Follow the instructions in this section to mount the Signal Booster on a wall. PS71090 Product Manual January 2017, Rev A Figure 5-1: Signal Booster Mounting 1. Using the PS71090 as a template, mark the four (4) locations for the wall anchoring system screws. 2. Move the PS71090 unit and drill the mounting holes at the marks in the wall. Install a wall anchor in each of the four (4) drilled holes. 3. Install the top two (2) screws into the anchors, leaving enough room to slide the screws into the oblong holes of the top of the units mounting positions. 4. Once the Unit is hung on the top two (2) screws finish fastening the top screws. 5. Install the bottom two (2) screws into the anchors, fastening the Unit to the wall. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 25 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 5.5 Verifying the Physical System Setup Check all cables for shorts and opens. Verify that there are no cables with loose or poor connections. RF leakage could cause oscillation to occur under some conditions. If the rooftop antenna (donor antenna) is directional, check it for proper alignment along the calculated compass heading. Typically, the directional antenna would be aimed at the same site that your handset uses, but that may not always be the case. If cables and alignment are acceptable, and a problem persists, use a spectrum analyzer to examine the signal environment in which the unit is operating. The existence of strong adjacent channel signals within the frequency band(s) can cause the AGC to reduce the amplifiers gain or cause alarms. In some cases, additional filtering or attenuation may be required to reject these unwanted signals. In some instances, the donor antenna can be reoriented horizontally to place the interference source in an antenna pattern null. 5.6 Controlling the Signal Booster Control and monitoring the Signal Booster requires that a properly configured computer with Westell PS71090 control software installed is connected via an Ethernet cable, such as the one shown in Figure 5-3. Connect the Ethernet cable from the Network Interface port of a computer to the GUI port on the bottom end panel of the Signal Booster. Figure 5-3A: Ethernet Cable Figure 5-3B: Ethernet Connectors 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 26 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Connecting to the Alarm Relay Panel 5.7 Use the provided Alarm Relay Serial Cable to connect the PS71090 Public Safety Signal Booster to the alarm relay panel. If the provided cable is not long enough for your system, you will need to build one. 1. Strip the outer serial cable insulation back to expose the inner conductors, Figure 5-4. Only the red, black and brown conductors will be used. You may cut the remaining conductors back to end of the outer insulation to keep them out of the way. 2. Strip back the insulation on the ends of each conductor. Figure 5 - 4 : Stripped Cable Conductors 3. Remove the protective cover on the Alarm Relay 9 position D-Sub connector. Figure 5-5: Alarm Relay 9 Position D-Sub Connector WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 27 of 51 4. Connect the 9 position D-Sub connector at one end of the serial cable to the Alarm Relay connector on the PS71090, Figure 5-6. Be sure to fasten the connector screws securely. PS71090 Product Manual January 2017, Rev A Figure 5-6: Alarm Relay Cable Connected to Signal Booster 5. Connect the stripped end of the serial cable to the alarm relay panel. Refer to Table 5-1 for connection information. Table 5-1: Alarm Relay Connections Pin Number Contact Type Conductor Color 1 2 3 NC NO CC Black Brown Red 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 28 of 51 WESTELL.COM Connecting the Power Cable 5.8 Use the provided AC Power Cable to connect the PS71090 Public Safety Signal Booster to an AC power source. PS71090 Product Manual January 2017, Rev A 1. Remove the cap from the AC 110V power connector on the Signal Booster, Figure 5-7. Figure 5-7: Remove the Power Connector Cap 2. Connect the power cable to the AC 110V power connector on the Signal Booster, Figure 5-9. NOTE The Signal Booster connector and the cable connector are keyed as shown in Figure 5-8. Figure 5-8: Connector Keys 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 29 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Figure 5-9: Power Cable Connected to Signal Booster 3. Screw the connector on securely. 4. When the Signal Booster is properly set up and ready to have power applied, plug the other end into the 110VAC outlet. Figure 5-10: Power Cable Connected to Signal Booster 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 30 of 51 WESTELL.COM Connecting the Battery Back-up Cable 5.9 Use the provided DC Power Cable to connect the PS71090 Public Safety Signal Booster to a Battery Back-up power source. PS71090 Product Manual January 2017, Rev A Figure 5-11: Battery Cable Connected to Signal Booster 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 31 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A 6 System Operation 6.1 Operating the Program Access the PS71090 Public Safety Signal Booster using the provided PS71090 PS-SMR 700/800 software through a LAN connection. The Signal Booster ships with the IP address 192.168.1.150. To connect directly to the Signal Booster from a laptop or PC with a crossover CAT-5E cable or over a LAN, change the TCP/IP settings on your computer to enable a connection to a host that has a static IP. 1. Select Use the following IP Address and enter the IP address 192.168.1.x, where x is any number from 2 to 254, inclusive, other than 150. 2. Ensure that the subnet mask is set to 255.255.255.0. Refer questions about these settings to your IT department. NOTE 1) Navigate to the RSSMR78M4B3301.exe software file and double-click to run it. The Status page, displays. WESTELL.COM January 2017; Doc No. CS14702802UM rE Page 32 of 51 2017 Westell Technologies 1.877.844.4274 PS71090 Product Manual January 2017, Rev A Item Description 1 2 3 IP Address Field (editable when Connect button is displayed) Connect/Disconnect toggle button TX/RX LED indicates the state of communication with the Signal Booster and GUI 2) Verify that the IP address in the upper right of the page is correct. If it is not, edit it in the IP Address field. 3) Click the Connect button. The button label changes to Disconnect.
(Default) User Name : admin
(Default) Password
: admin 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 33 of 51 WESTELL.COM 6.2 Status Clicking the Status button in the menu on the left of the page changes the button text to and displays the Status Mode page, described in this section. PS71090 Product Manual January 2017, Rev A Item #
1 Figure 6-1: Status Mode Page Section System Not User-Configurable/Informational Only Manufacture Displays the Signal Boosters manufacturer Signal Booster Type Displays Signal Booster Model Number Signal Booster S/N Displays Signal Booster Serial Number S/W Version Displays firmware version of the control board Temperature Displays internal temperature of the Signal Booster Item #
2 Location Section Company Company information display Address Address information display City State City information display State information display Contact Contact information display 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 34 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Item #
3 700 MHz Section Uplink Start Frequency Displays 700 MHz uplink Start frequency Stop Frequency Displays 700 MHz uplink Stop frequency Downlink Start Frequency Displays 700 MHz downlink Start frequency Stop Frequency Displays 700 MHz downlink Stop frequency 700MHz Band Allows Main-band to be set to Select 4 Downlink Gain [dB]
Displays downlink gain in the 700 MHz range DL Output[dBm] Displays output level of the 700 MHz range AGC Level [dBm] Sets units maximum AGC output value HPA Allows the user to toggle the downlink HPA on or off Item #
5 800 MHz Section Sub-band 1 Uplink Start Frequency Displays sub-band 1 uplink Start frequency Stop Frequency Displays sub-band 1 uplink Stop frequency Downlink Start Frequency Displays the sub-band 1 downlink start frequency Stop Frequency Displays sub-band 1 downlink Stop frequency 800MHz Band Allows sub-band 1 to be set to Select Sub-band 2 Uplink Start Frequency Displays sub-band 2 uplink Start frequency Stop Frequency Displays sub-band 2 uplink Stop frequency Downlink Start Frequency Displays sub-band 2 downlink start frequency Stop Frequency Displays sub-band 2 downlink Stop frequency 800MHz Band Allows sub-band 2 to be set to Select 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 35 of 51 WESTELL.COM Item #
5, continued PS71090 Product Manual January 2017, Rev A Section Sub-band 3 Uplink Start Frequency Displays sub-band 3 uplink Start frequency Stop Frequency Displays sub-band 3 uplink Stop frequency Downlink Start Frequency Displays sub-band 3 downlink Start frequency Stop Frequency Displays sub-band 3 downlink Stop frequency 800MHz Band Allows sub-band 3 to be set to Select Uplink 700 & 800 MHz Gain (dB) Displays status of the uplink gain UL Output [dBm]
Displays uplink output level ALC Level [dBm]
Sets the units maximum ALC output value HPA Isolation Isolation Value Isolation Allows the user to toggle the uplink high power amplifier on or off When power is on, an isolation check is performed and the values are displayed The isolation check can be performed with the RF on or off Note: Neither the isolation check, nor recheck, will indicate a change in power levels if the units own power has been switched off. 6 7 Item #
8 Section Alarm Status Not User-Configurable/Informational Only
( GREEN = Normal; RED = Alarm ) PLL LD Isolation Display alarm Display alarm Shutdown (DL/UL) Display alarm DC Fail Display alarm Relay Status Display alarm DL VSWR DL Path VSWR check UL VSWR UL Path VSWR check Manual Amp User HPA OFF Alarm BATT FAIL (LOW) BATT Low Power Alarm BATT FAIL (HIGH) BATT High Power Alarm 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 36 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Item #
Section DC FAIL BATT / AC Power Alarm DL HPA FAIL DL Path HPA Alarm UL HPA FAIL UL Path HPA Alarm 9 VSWR ( DL / UL ) Ratio Limit VSWR Ratio Status Display, 0.00 to 30.00 VSWR Ratio Alarm Limit , Set 0.00 to 30.00 On/Off VSWR Alarm Display Enable(On)/Display(Off) 10 AC/DC Info AC or BATT Status Display Charge Status Charge Status Display Charge / Discharge Voltage AD or DC Voltage Display 0.0 ~ 29.0 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 37 of 51 WESTELL.COM 6.3 Control Clicking the Control button in the menu on the left of the page changes the button text to and displays the Control Mode page, described in this section. PS71090 Product Manual January 2017, Rev A Figure 6-2: Control Mode Page Item #
1 700 MHz Section Uplink Start Frequency Displays 700 MHz uplink Start frequency Stop Frequency Displays 700 MHz uplink Stop frequency Downlink Start Frequency Displays the 700 MHz downlink Start frequency Stop Frequency Displays the 700 MHz downlink Stop frequency WESTELL.COM January 2017; Doc No. CS14702802UM rE Page 38 of 51 2017 Westell Technologies 1.877.844.4274 Item #
2 Downlink Gain [dB]
PS71090 Product Manual January 2017, Rev A Section Displays downlink gain in the 700 MHz range ALC Atten [dB]
Displays attenuation value by ALC Atten [dB]
Displays attenuation value controlled by down link AGC Atten [dB]
Displays attenuation value controlled by AGC AGC Control Auto Level Control Function On/Off AGC Level [dBm]
Sets the units maximum ALC output value HPA Down link HPA On/Off Shutdown Allows the shut-down level to be set Downlink Shutdown Allows the downlink shutdown level to be set to on or off. Shutdown Level
[dBm]
Allows the maximum shutdown level to be set between 23 and 37 Uplink Shutdown Allows the uplink shut down level to be set to on or off Shutdown Level
[dBm]
Allows the maximum shutdown level to be set between 23 and 37 Shutdown Period Allows the shutdown period to be set Shutdown Period Allows the shutdown period to be set in minutes and seconds. 800 MHz Section Sub-band 1 Uplink Start Frequency Displays sub-band 1 uplink Start frequency Stop Frequency Displays sub-band 1 uplink Stop frequency Downlink Start Frequency Displays sub-band 1 downlink Start frequency Stop Frequency Displays sub-band 1 downlink Stop frequency 800 MHz Band Allows sub-band 1 to be set to Select Sub-band 2 Uplink Start Frequency Displays sub-band 2 uplink start frequency 3 4 Item #
5 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 39 of 51 WESTELL.COM PS71090 Product Manual January 2017, Rev A Section Downlink Gain [dB]
Displays downlink gain in the 700 MHz range ALC Atten [dB]
Displays attenuation value by ALC Atten [dB]
Displays attenuation value controlled by down link AGC Atten [dB]
Displays attenuation value controlled by AGC AGC Control Auto Level Control Function On/Off AGC Level [dBm]
Sets the units maximum ALC output value HPA Down link HPA On/Off End Frequency Displays the sub-band 2 uplink end frequency Downlink Start Frequency Displays sub-band 2 downlink Start frequency Stop Frequency Displays sub-band 2 downlink Stop frequency 800 MHz Band Allows sub-band 2 to be set to Select Section Sub-band 3 Uplink Start Frequency Displays sub-band 3 uplink Start frequency Stop Frequency Displays sub-band 3 uplink Stop frequency Downlink Start Frequency Displays sub-band 3 downlink start frequency Stop Frequency Displays sub-band 3 downlink Stop frequency 800 MHz Band Allows sub-band 3 to be set to Select Uplink 700 & 800 MHz 700 MHz Band Drop-Down Allows selection to turn the 758-775 MHz band on or off 800 MHz Band Drop-Down Allows selection to turn the 851-854 MHz Band on or off Allows selection to turn the 851-861 MHz Band on or off Allows selection to turn the 851-869 MHz Band on or off 5, continued Item #
2 Item #
5, continued 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 40 of 51 WESTELL.COM Item #
6 PS71090 Product Manual January 2017, Rev A Section Gain (dB) Displays status of the uplink gain ALC Atten [dB]
Displays attenuation value controlled by ALC Atten [dB]
Sets the attenuation value AGC Atten [dB]
Displays attenuation value controlled by AGC AGC Control Auto Gain Control Function On/Off AGC Level [dBm] Sets the units maximum AGC output value HPA Uplink HPA On/Off 7 Alarm ( GREEN = Normal; RED = Alarm ) PLL LD Isolation Shutdown
(DL/UL) Displays alarm Displays alarm Displays alarm DC Fail Displays alarm Relay Status Displays alarm DL VSWR DL Path VSWR check UL VSWR UL Path VSWR check Manual Amp User HPA OFF Alarm BATT FAIL (LOW) BATT Low Power Alarm BATT FAIL (HIGH) BATT High Power Alarm DC FAIL BATT / AC Power Alarm DL HPA FAIL DL Path HPA Alarm UL HPA FAIL UL Path HPA Alarm WESTELL.COM January 2017; Doc No. CS14702802UM rE Page 41 of 51 2017 Westell Technologies 1.877.844.4274 Item #
8 Isolation Isolation Value Isolation Isolation Recheck PS71090 Product Manual January 2017, Rev A Section When power is on, an isolation check is performed and the values display. The isolation check can be performed with the RF on or off. The isolation check can be performed with the RF on or off. Note: Neither the isolation check nor recheck will indicate a change in power levels if the units own power has been switched off. 9 VSWR 10 Ratio Limit On/Off Location Company Address City State Contact DL/UL VSWR Ratio Status Display, 0.00 to 30.00 VSWR Ratio Alarm Limit , Set 0.00 to 30.00 VSWR Alarm Display Enable(On)/Display(Off) Company information display Address information display City information display State information display Contact information display 11 Control Send When the unit is fully configured, the settings can be sent to the Signal Booster by clicking the Control Send button. 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 42 of 51 WESTELL.COM 7.0 Installing Software Installation 1) Insert the included media into your computer and locate the Setup.exe file. 2) Double-click the file to begin software installation. PS71090 Product Manual January 2017, Rev A 3) Navigate to the destination directory in which you want to install the file, Figure 6-3. Figure 6-3: Navigate to the destination directory 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 43 of 51 WESTELL.COM 4) Click Next. The progress window, displays, Figure 6-4. PS71090 Product Manual January 2017, Rev A Figure 6-4: Click Next to Begin Installation Figure 6-5: Installation Progress Window 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 44 of 51 WESTELL.COM 5) When the installation is complete, click Finish, Figure 6-6. PS71090 Product Manual January 2017, Rev A Figure 6-6: Installation Complete WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 45 of 51 PS71090 Product Manual January 2017, Rev A 7.1 Upgrading the Firmware Follow the instructions in this section to upgrade to a newer version of system firmware, if necessary. 1. Click the Control button to display the Control page. 2. Click in the IP menu located on the left side of the Control page. The Firmware Upgrade progress window, Figure 7-1, displays. Figure 7-1: Firmware Upgrade Progress Window File Open Tab 3. Click the File Open tab in the Firmware Upgrade progress window to display it, Figure 7-1. 4. Click to select the desired version file. 5. Click in the Specify INI File to Open browser window, Figure 7-2. The Firmware Version Check dialog window displays, Figure 7-2. Figure 7-2: Firmware Version Check 6. Click in the Firmware Version Check dialog window, Figure 7-3. The firmware upgrade begins, as indicated by the progress bar in the Firmware Version Check window, Figure 7-3. 2017 Westell Technologies 1.877.844.4274 WESTELL.COM January 2017; Doc No. CS14702802UM rE Page 46 of 51 PS71090 Product Manual January 2017, Rev A Figure 7-3: Firmware Update Status
#
1 2 3 Item Stop Function Button to Stop Upgrade Status Display real-time upgrade status Progress Display Upgrade Progress Note: You can stop the upgrade by pressing the Stop button. 7. When upgrade is completed, Firmware Upgrade Window is closed. WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 47 of 51 7.2 IP Change PS71090 Product Manual January 2017, Rev A Figure 7-3: IP Settings 1. With Control ON, the IP Change button is activated. 7.2.1 IP Change Window Figure 7-4: IP Change Window 1. Successful completion of IP Read, Status LED turns green and change icon is activated 2. When the IP Change Window is opened, the current status is displayed, Figure 7-10 a. Static IP can be set. (See 7.2.2) b. DHCP IP can be set. (See 7.2.3) WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 48 of 51 7.2.2 Static IP Setting PS71090 Product Manual January 2017, Rev A Figure 7-5: Static IP Setting 1. Please write the Address / netmask / broadcast / gateway 2. If have all information set, please press YES button. 7.2.3 DHCP IP Setting 1. After DHCP select please click the YES button. Figure 7-6: DHCP IP Setting WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 49 of 51 Appendix A Important Product Information PS71090 Product Manual January 2017, Rev A A.1 Registration Number FCC NVRCSIT51080SP78 A.2 UL This product is UL Listed. WESTELL.COM 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 50 of 51 Appendix B Table B-1 contains the acronyms and abbreviations used in this manual, along with a definition for each one. Acronyms and Abbreviations PS71090 Product Manual January 2017, Rev A Table B-1: Acronyms and Abbreviations Acronym/Abbreviation Definition AC AGC COM dB dBc dBi dBm DC DL FCC HPA Alternating Current Automatic Gain Control Communications Decibels Decibels relative to the carrier Decibels relative to isotropic The power ratio in decibels (dB) of the measured power referenced to one milliwatt (mW) Direct Current Downlink Federal Communications Commission High-Powered Amplifier IF SAW Intermediate Frequency Surface Acoustic Wave IP LAN LED MHz NMS OSC PLL LD RF RS-232C UL UPS VAC VSWR Internet Protocol Local Area Network Light Emitting Diode Megahertz Network Management System Oscillator Phase-locked loop with lock detection Radio Frequency Serial Communication Standard Uplink Uninterruptable Power Supply Volts Alternating Current (AC Voltage) Voltage Standing Wave Ratio 2017 Westell Technologies 1.877.844.4274 January 2017; Doc No. CS14702802UM rE Page 51 of 51 WESTELL.COM
| frequency | equipment class | purpose | ||
|---|---|---|---|---|
| 1 | 2017-02-09 | 862 ~ 869 | B9B - Part 90 Class B Industrial Booster (non-SMR) | Original Equipment |
| app s | Applicant Information | |||||
|---|---|---|---|---|---|---|
| 1 | Effective |
2017-02-09
|
||||
| 1 | Applicant's complete, legal business name |
Westell, Inc.
|
||||
| 1 | FCC Registration Number (FRN) |
0010374171
|
||||
| 1 | Physical Address |
750 North Commons Drive
|
||||
| 1 |
Aurora, Illinois 60504
|
|||||
| 1 |
United States
|
|||||
| app s | TCB Information | |||||
| 1 | TCB Application Email Address |
T******@TIMCOENGR.COM
|
||||
| 1 | TCB Scope |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
||||
| app s | FCC ID | |||||
| 1 | Grantee Code |
NVR
|
||||
| 1 | Equipment Product Code |
PS71090-PS78
|
||||
| app s | Person at the applicant's address to receive grant or for contact | |||||
| 1 | Name |
J****** K**** G****
|
||||
| 1 | Title |
Compliance Engineer
|
||||
| 1 | Telephone Number |
630-3********
|
||||
| 1 | Fax Number |
630-3********
|
||||
| 1 |
j******@westell.com
|
|||||
| app s | Technical Contact | |||||
| n/a | ||||||
| app s | Non Technical Contact | |||||
| n/a | ||||||
| app s | Confidentiality (long or short term) | |||||
| 1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
| 1 | If so, specify the short-term confidentiality release date (MM/DD/YYYY format) | 08/08/2017 | ||||
| if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
| app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
| 1 | Is this application for software defined/cognitive radio authorization? | No | ||||
| 1 | Equipment Class | B9B - Part 90 Class B Industrial Booster (non-SMR) | ||||
| 1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Public Safety Repeater | ||||
| 1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
| 1 | Modular Equipment Type | Does not apply | ||||
| 1 | Purpose / Application is for | Original Equipment | ||||
| 1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
| 1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
| 1 | Grant Comments | Booster. Power output is conducted. F1D and G1D emissions are included under the F1E listing, per 90.207(l). The intended use is generally for industrial/commercial use and will not be sold to the general public. Professional installation is required. The antenna(s) used for this transmitter are to be fixed-mounted on indoor or outdoor structures. RF exposure compliance will need to be addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of Sec. 1.1307(b)(3). This repeater is for private use and public safety operation. | ||||
| 1 | Is there an equipment authorization waiver associated with this application? | No | ||||
| 1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
| app s | Test Firm Name and Contact Information | |||||
| 1 | Firm Name |
Compliance Worldwide, Inc.
|
||||
| 1 | Name |
M**** M********
|
||||
| 1 | Telephone Number |
603-8********
|
||||
| 1 | Fax Number |
603 8********
|
||||
| 1 |
m******@complianceworldwide.com
|
|||||
| Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
| 1 | 1 | 9 | PF | 758 | 768 | 2.1 | Amp | F9W | |||||||||||||||||||||||||||||||||
| 1 | 2 | 9 | 769 | 775 | 2 | Amp | F1E | ||||||||||||||||||||||||||||||||||
| 1 | 3 | 9 | 769 | 775 | 2 | Amp | F3E | ||||||||||||||||||||||||||||||||||
| 1 | 4 | 9 | PF | 788 | 798 | 2.1 | Amp | F9W | |||||||||||||||||||||||||||||||||
| 1 | 5 | 9 | 799 | 805 | 1.9 | Amp | F1E | ||||||||||||||||||||||||||||||||||
| 1 | 6 | 9 | 799 | 805 | 1.9 | Amp | F3E | ||||||||||||||||||||||||||||||||||
| 1 | 7 | 9 | 806 | 816 | 2 | Amp | F1E | ||||||||||||||||||||||||||||||||||
| 1 | 8 | 9 | 806 | 816 | 2 | Amp | F3E | ||||||||||||||||||||||||||||||||||
| 1 | 9 | 9 | 817 | 824 | 2 | Amp | F1E | ||||||||||||||||||||||||||||||||||
| 1 | 1 | 9 | 817 | 824 | 2 | Amp | F3E | ||||||||||||||||||||||||||||||||||
| 1 | 11 | 9 | 851 | 861 | 1.9 | Amp | F1E | ||||||||||||||||||||||||||||||||||
| 1 | 12 | 9 | 851 | 861 | 1.9 | Amp | F3E | ||||||||||||||||||||||||||||||||||
| 1 | 13 | 9 | 862 | 869 | 1.9 | Amp | F1E | ||||||||||||||||||||||||||||||||||
| 1 | 14 | 9 | 862 | 869 | 1.9 | Amp | F3E | ||||||||||||||||||||||||||||||||||
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC