FCC ID: 2AT9N-WW-BT-VC-V2 Bluetooth adaptor

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instruc-

tions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. WET SOUNDS INC. www.wetsounds.com 877-938-7757 10621 S Sam Houston PKWY W Suite 100 Houston, TX 77071-3140 WET SOUNDS BLUETOOTH VOLUME CONTROL WW-BT-VC V2 Revision Date: Aapril 2022 WET SOUNDS BLUETOOTH VOLUME CONTROL WW-BT-VC V2 WIRING INSTALLATION INSTRUCTIONS:

The WW-BT-VC V2 is an easy to operate single control knob Bluetooth Volume Controller. Wire Color Standard Wiring Method

(switched power source) Alternative Wiring Method

(non-switched power source) One simple knob controls all Bluetooth functions as well as the system volume!

Red Wire 12v +

HOW TO CONNECT TO THE WW-BT-VC V2 BLUETOOTH CONTROLLER THROUGH BLUETOOTH PAIRING:

Yellow Wire 12v +

Step 1: Turn on WW-BT-VC V2 by turning on your ignition or dash switch. The red LED indicates that the WW-BT-VC V2 is ready to use. Step 2: Press in and hold the Bluetooth knob until you see the blue paired with your Bluetooth enabled smart phone or portable device. Step 3:

V2 and connect to it.

(To unpair from the WW-BT-VC V2 simply double tap the controller knob.) Follow your phones instruction guide for Bluetooth pairing. Make sure that Bluetooth is activated on your mobile phone. OPERATING INSTRUCTIONS:

Blue LED Red LED Play Music: Start your media player or music streaming service Pause Music: Tap the knob once to pause, tap a second time to resume play mode Skip One Track Forward: Turn knob Clockwise for approx. 1 second Skip One Track Backward: Turn knob Counter-clockwise for approx. 1 second Adjust Volume Up: Turn and hold the knob Clockwise to desired volume level Adjust Volume Down: Turn and hold the knob counter-clockwise to desired volume level Wire to 12v positive (+) power switch (ignition or dash switch) Wire to 12v positive (+) continuous power source

(fused) Unused, properly isolated and capped off Wired to a 12v positive (+) continuous power source Blue Wire 12v +

Wire to amp or EQ turn on input (+) Wire to amp or EQ turn on input (+) Black Wire Ground Wire to battery negative (-) ground terminal or ground terminal block Wire to battery negative (-) ground terminal or ground terminal block NOTE: To Power Unit On/Off Manually - simply push in and hold the knob until the unit powers on or off. This allows you to turn unit off if a vehicle switch MOUNTING INSTRUCTIONS:

Surface Mount / Under Dash Mount Use two Phillips screws to mount controller on dash surface or under dash applications using the supplied surface/under dash mounting adapter. Flush Mount / In-dash Mount Remove the surface mount portion of the controller by unscrewing the main nut on the WW-BT-VC V2 body. Drill a 7/8 hole in your desired mounting location making sure that you have checked for tolerances and/or obstacles behind the dash. Once the hole is drilled, install the controller from the front and secure it with the main body nut from behind. Make sure the Bluetooth knob is correctly orientated before tightening into place. THANK YOU FOR CHOOSING WET SOUNDS!

CONFIDENTIALITY REQUEST for Certification Service in USA Federal Communication Commission Equipment Authorization Division, Application Processing Branch 7435 Oakland Mills Road Columbia, MD 21046 Date: 2022/5/7 Pursuant to Paragraphs 0.457 and 0.459 of the Commission's Rules (47 C.F.R.) and Section 552(b)(4) of the Freedom of Information Act, we requests confidentiality for the following products:

FCC ID Model name 2ATON-WW-BT-VC-V2 WW-BT VC-V2 For the product stated above, we request that the following information be held confidential;

Long-Term Short-Term Short-Term Exhibits Confidentiality Confidentiality Confidentiality Days External Photos Internal Photos Block Diagram Xx Schematics Xx Test Setup Photos Users Manual Parts List Tune Up Operational Descriptions Xx The long-term confidentiality exhibits contain our trade secrets and proprietary information that could be of benefit to our competitors. The short-term confidentiality on the basis of ensuring that business sensitive information remains confidential until the actual marketing of our new device. If you have any questions, please feel free to contact me at the address shown below. Sincerely, O_onx Sender?

Name/Title: Gabe Sandoval / Project Manager Company: Wet Sounds Inc. Address: 2975 Louise Street, Rosenberg, Texas 77471, United States Phone: +1 (877)938-7757 Fax: /

E-Mail: gabe@wetsounds.com

Wet Sounds Inc. 2975 Louise Street, Rosenberg, Texas 77471, United States Federal Communications Commission Authorization and Evaluation Division Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MD 21046 2022-5-6 To whom it may concern:

We, Wet Sounds Inc. the undersigned, hereby authorize Eurofins Product Service GmbH to act on our behalf in all matters relating to applications for equipment authorization FCC ID: 2AT9IN-WW-BT-VC-V2 including the signing of all documents related to these matters. Any and all acts carried out by Eurofins Product Service GmbH on our behalf shall have the same effect as acts of our own. By signing this application form, we agree to Eurofins current valid General Terms and Conditions

(AGB),Testing and Certification Regulations (PZO) which can be viewed on following website www.eurofins.de/ee or retrieved on request. We also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Sincerely, O_re Dendere Name/Title: Gabe Sandoval / Project Manager Company: Wet Sounds Inc. Address: 2975 Louise Street, Rosenberg, Texas 77471, United States Phone: +1 (877)938-7757 Fax: /

E-Mail: gabe@wetsounds.com