SMART KEY System Host Model Name: SMART KEY SYSTEM Host Trade Name: 2W SKS Model Number: WR00098800T1 Type:S100324800 L.O freq: 8MHz Electrical Specifications Characteristics Item Rated voltage Operation voltage Specifications Remarks DC12V DC8V~16V
-
-
Dark current
<1mA(max)@12VDC Passive mode RF receiving frequency LF transmitting frequency Communication format RF Modulation method Operating temperature range Storage temperature range 433.92MHz 250KHz 125KHz 2.5KHz N/A FSK
-30~+80
-40~+85
-
-
-
-
-
PHOTOGRAPHS 1 SMART KEY System Host Model Name: SMART KEY SYSTEM Host Trade Name: 2W SKS Model Number: WR00098800T1 Type:S100324800 L.O freq: 8MHz P.C.B (Front) P.C.B (Back) 2 SMART KEY System Host Model Name: SMART KEY SYSTEM Host Trade Name: 2W SKS Model Number: WR00098800T1 Type:S100324800 L.O freq: 8MHz Block Diagram 3 SMART KEY System Host Model Name: SMART KEY SYSTEM Host Trade Name: 2W SKS Model Number: WR00098800T1 Type:S100324800 L.O freq: 8MHz Roadmap 4 Cautions:
To prevent electric shock or short circuit damage, please ask a qualified technician for installing.
Please use an independent power supply so that the failure caused by the unstable power will not occur.
Metal will block the radio signal. Therefore, stay away from metal when installing the product. Remote control distance will also become shorter when there is a same frequency signal around.
Adjacent products should be separated at least 3 meters.
If there is a malfunction of the product, please contact the service department. Functional check list NO. Check Items Detail items Condition Operation(Input) Result
Power input 12V0.1V
Place the smart key on the 1.Move the smart key away 1 HOST Identification Fail
(Immo Coil) surface of the Immo. Coil from sensing area(more If identification failthe host goes 2.5mm than 5cm) into standby and do not do OK NG
The smart key need to 2.Push power bottom at anything. Immo sensing Distance 8cm 2 HOST Identification Fail
(Immo Coil) remove battery or disconnect 300ms LF antenna
Power input 12V0.1V 1.Identification after every 3
Place the smart key on the Move the smart key away seconds surface of the Immo. Coil from sensing area(more 2.If identification failsystem will 2.5mm than 5cm) lock
The smart key need to 3.The buzzer sounds for 500ms.
- 9 -
Remove the OK NG smart key more than 10 cm. remove battery or disconnect LF antenna
If identification Pass, system unlock
Power input 12V0.1V
Place the smart key on the surface of the Immo. Coil 3 HOST Lock(Immo Coil) 2.5mm
The smart key need to remove battery or disconnect LF antenna 4 HOST Unlock(Immo Coil)
Power input 12V0.1V
Power input 12V0.1V.
Place the smart key within the surface of the LF antenna 150cm.
The lock is locked.
Power input 12V0.1V 5 HOST Identification Pass(Antenna) 6 HOST Identification fail(Antenna) 4.Red LED lights up for 2 seconds 5.Extinguish the blue LED 1. Identification after every 3 seconds. Turn the dial to switch the 2. If identification failsystem will IGN status lock. IGN OFFIGN ON IGN 3. The buzzer sounds for 500ms. OFF one time. 4. Red LED lights up for 2 OK NG Change IGN OFF/IGN OFF2 Switch to IGN ON Power Bottom pressed 300ms seconds. 5. Extinguish the blue LED. 1.System will lock 2. Blue LED will light up slowly 1. If identification is successfully , the drive lock is unlocked, and the OK NG blue LED will slowly light up. OK NG 2. Buzzer short beep 2
(ON/OFF:100ms/100ms)
Place the smart key outside 1.Place the smart key the surface of the LF antenna outside the surface of the 300cm. LF antenna 300cm.
The lock is locked. 2.Power Bottom pressed 300ms. If identification failed, no action is taken, the host goes into standby OK NG 7 HOST Identification margi(Antenna)
Power input 12V0.1V 1.Power Bottom presses
Place the smart key within 300ms for system unlock. 1. The system first recognizes the unlock and then enters the 3 OK NG the surface of the LF antenna 2. Place the smart key second identification.
- 10 -
150cm. surface of the LF antenna
The lock is locked. within 230cm~260 cm, and 2. After counting 2 seconds, press Power Button to perform locking press the power button action. again. 3. The system performs lock, and
Power input 12V0.1V the buzzer sounds for 500ms. 4.Red LED light up for 2 seconds. 5. Extinguish the blue LED. 1. Identification after every 3 seconds of counting. 8 HOST Identificaton fail(Antenna) the surface of the LF antenna the surface of the LF execution lock 150cm. antenna 300cm. 3. The buzzer sounds for 500ms. OK NG
Place the smart key within Place the smart key outside 2.Identification failed, system
Identification first, after the system is unlocked. 4. Red LED light up for 2 seconds. 5. Extinguish the blue LED. 1.System execution lock. 9 HOST Lock(Antenna)
Power input 12V0.1V Change IGN OFF/IGN OF2 2.The blue LED will slowly light Switch to IGN ON. up. OK NG 10 HOST Lock 11 HOST Lock
Power input 12V0.1V
Place the smart key surface of the LF antenna within150cm~300 cm. If the turntable is pressed, touch the positioning signal Pull Low.
Power input 12V0.1V 1.Power Bottom pressed
Place the smart key within 300ms the surface of the LF antenna 2. Positioning signal Pull 150cm. Low.
- 11 -
The system cannot perform locking. OK NG 1.Red LED ON/OFF
(500ms/500ms)continued 10 seconds. 2.Buzzer sound ON/OFF
(500ms/500ms)continued 10 seconds. OK NG 12 HOST Lock 13 HOST Lock 3.System power off. 1.Power Bottom pressed 300ms.
Power input 12V0.1V 2.Positioning signal Pull 1.
Place the smart key within the surface of the LF antenna 150cm. Low. 3. During the warning reminder time, after the positioning signal Pull Low is released
Power input 12V0.1V
Place the smart key within the surface of the LF antenna 1.Power Bottom pressed 150cm. 300ms
Turn the dial to switch the 2. Positioning signal Pull IGN status High. IGN OFFIGN ON IGN OFF one time. 2. The buzzer sounds for 500ms. 3.Red LED light up for 2 seconds. OK NG 1. System execution lock. 2. The buzzer sounds for 500ms. OK NG 3. Red LED light up for 2 seconds.
- 12 -
N O T E
:
T h i s e q u i p m e n t h a s b e e n t e s t e d a n d f o u n d t o c o m p l y w i t h t h e l i m i t s f o r a C l a s s B d i g i t a l d e v i c e
, p u r s u a n t t o p a r t 1 5 o f t h e F C C R u l e s
. T h e s e l i m i t s a r e d e s i g n e d t o p r o v i d e r e a s o n a b l e p r o t e c t i o n a g a i n s t h a r m f u l i n t e r f e r e n c e i n a r e s i d e n t i a l i n s t a l l a t i o n
. T h i s e q u i p m e n t g e n e r a t e s
, u s e s a n d c a n r a d i a t e r a d i o f r e q u e n c y e n e r g y a n d
, i f n o t i n s t a l l e d a n d u s e d i n a c c o r d a n c e w i t h t h e i n s t r u c t i o n s
, m a y c a u s e h a r m f u l i n t e r f e r e n c e t o r a d i o c o m m u n i c a t i o n s
. H o w e v e r
, t h e r e i s n o g u a r a n t e e t h a t i n t e r f e r e n c e w i l l n o t o c c u r i n a p a r t i c u l a r i n s t a l l a t i o n
. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
(1) this device may not cause interference,
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
1) Lappareil ne doit pas produire de brouillage;
2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement.
- 13 -
I f t h i s e q u i p m e n t d o e s c a u s e h a r m f u l i n t e r f e r e n c e t o r a d i o o r t e l e v i s i o n r e c e p t i o n
, w h i c h c a n b e d e t e r m i n e d b y t u r n i n g t h e e q u i p m e n t o f f a n d o n
, t h e u s e r i s e n c o u r a g e d t o t r y t o c o r r e c t t h e i n t e r f e r e n c e b y o n e o r m o r e o f t h e f o l l o w i n g m e a s u r e s
:
R e o r i e n t o r r e l o c a t e t h e r e c e i v i n g a n t e n n a
. I n c r e a s e t h e s e p a r a t i o n b e t w e e n t h e e q u i p m e n t a n d r e c e i v e r
. C o n n e c t t h e e q u i p m e n t i n t o a n o u t l e t o n a c i r c u i t d i f f e r e n t f r o m t h a t t o w h i c h t h e r e c e i v e r i s c o n n e c t e d
. C o n s u l t t h e d e a l e r o r a n e x p e r i e n c e d r a d i o
/
T V t e c h n i c i a n f o r h e l p
.