ZW1101 Door Window Sensor FCC/IC Federal Communications Commission (FCC) Statement FCC Caution: Any changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may caus harmful interference to radio communications.However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.Increase the separation between the equipment and receiver.Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.Consult the dealer or an experienced radio/TV technician for help.This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. IC Caution:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. DECLARATION DE CONFORMITE D'INDUSTRIE CANADA Ce priphrique a t test et reconnu conforme aux limites spcies dans RSS-210. Son utilisation est soumise aux deux conditions suivantes :
(1) il ne doit pas provoquer d'interfrences gnantes et
(2) il doit tolrer les interfrences re.ues, notamment cellessusceptibles d'en perturber le fonctionnement. WARRANTY Show Home Products warrants this product to be free from manufacturing defects for a period of two years from the original date of consumer purchase. This warranty is limited to the repair or replacement of this product only and does not extend to consequential or incidental damage to other products that may be used with this product. This warranty is in lieu of all other warranties, expressed or implied. Some states do not allow limitations on how long an implied warranty lasts or permit the exclusion or limitation of incidental or consequential damage, so the above limitations may not apply to you. This warranty gives you specic rights, and you may also have other rights which vary from state to state. if the unit should prove defective within the warranty period. Door window sensor SPECIFICATIONS Model:ZW1101 Power supply: battery ER14250, 1/2AA, 3V. Signal (Frequency): 908.42 MHz. Operating Range: Up to 100 feet line of sight Operating Temp.: -15C~60C (5F ~140F) Wireless Controller and the closest Z-Wave receiver module. Specications subject to change without notice due to continuing product improvement Website www.ishowlights.com WARNING RISK OF FIRE RISK OF ELECTRICAL SHOCK RISK OF BURNS CONTROLLING APPLIANCES:
EXERCISE EXTREME CAUTION WHEN USING Z-WAVE DEVICES TO CONTROL APPLIANCES. OPERATION OF THE Z-WAVE DEVICE MAY BE IN A DIFFERENT ROOM THAN THE CONTROLLED APPLIANCE, ALSO AN UNINTENTIONAL ACTIVATION MAY OCCUR IF THE WRONG BUTTON ON THE REMOTE IS PRESSED. Z-WAVE DEVICES MAY AUTOMATICALLY BE POWERED ON DUE TO TIMED EVENT PROGRAMMING. DEPENDING UPON THE APPLI-
ANCE, THESE UNATTENDED OR UNINTENTIONAL OP-
ERATIONS COULD POSSIBLY RESULT IN A HAZARDOUS CONDITION. FOR THESE REASONS, WE RECOMMEND DO NOT RETURN THIS PRODUCT TO THE STORE THE FOLLOWING:
DO NOT USE Z-WAVE DEVICES TO CONTROL ELECTRIC HEATERS OR ANY OTHER APPLIANCES WHICH MAY PRES-
ENT A HAZARDOUS CONDITION DUE TO UNATTENDED OR UNINTENTIONAL OR AUTOMATIC POWER ON CONTROL. Product Introduction and description Thanks for choosing the show home wireless door/window sensor of the home security device.This sensor is a Z-Wave enabled device (interoperable, two-way RF mesh networking technology) and is fully compatible with any Z-Wave enabled network. Every mains powered Z-Wave enabled device acts as a signal repeater and multiple devices result in more possible transmission routes which helps eliminate RF dead-sportsZ-Wave enabled devices displaying the Z-Wave logo can also be used with it regardless of the manufacturer, and ours can also be used in other manufacturers Z-Wave enabled networks. This sensor monitors door/window and send Z-Wave signal when door or window is opened and closed. Operation Notice: If you install the entire Z-Wave system for the rst time, please refer to the installation guide of Z-Wave Interface Controller before installing ZW1101. 1. Unscrew the screw fastening the rear cover. 2. Slide the rear cover down. 3. Using the screws or adhesive tape to afx the rear cover on the frame along the opening edge of door / window. 4. Insert a CR123A battery into the battery compartment and LED will start to ash slowly,which means the sensor has not yet been added. 5. For adding to a network: Put the Z-Wave Interface Controller into adding mode, and following its instruction to add the ZW1101 to your controller. To get in the adding mode, the distance between sensor and controller is suggested to be in one meter. Press the program switch of ZW1101 for 1 second at least.The LED on the ZW1101 should go solid, if not, please try again.For removing from a network: Put the Z-Wave Interface Controller into removing mode, and following its instruction to delete the ZW1101 from your controller. Press the program switch of ZW1101 for 1 second at least to be removed.For Association: removing the cover of the ZW1101 to get into the Awake mode, then put the Z-Wave Interface Controller into Association, and following its instruction to associate the ZW1101 with other device. Close the cover back after association done, afterward the ZW1101 will get into Sleep mode for power saving. Support one association group (5 nodes).Awake mode: it is to leave the Sleep mode by removing the cover of ZW1101, to allow the Z-Wave Interface Controller to do add, remove, Association and to reply and receive the commands from controller. 6. Slide back the rear cover and screw fastening with the front cover, the LED should go off. 7. Fix the Magnet by using the adhesive tape or xing screws, locate the Magnet close to the ZW1101 sensor the distance between these two devices should be in 1.9cm. 8. External Switch: If your window needs two sensors for fully monitoring. You could use an external switch to connect with the ZW1101 for extending detection. The ZW1101 has 2 normally closed contact terminals. These can be used for additional external switch wired contacts. The external switch will send an alarm report (type:01,level:11) by opening the window/door. Package content:
ZW1101 Sensor-1pcs Bracket for Contact Magnet-1pcs Magnet-1pcs Adhesive tape for Magnet /sensor-2pcs CR14250 3.0V Battery-1pcs Screws for bracket/ sensor-4pcs Installation Operation manual-1pcs Assemble
. Step1.The magnet shall be xed to close to the specic area,and the distance from sensor shall not be over 1.9cm. Step2.Fixed with adhesive tap or Screws. g1 g2