1034048
#
Show White Color Color REMOTE CONTROL Remote Control Instructions 1. Remove insulating tape from the battery compartment before use. This remote is RF and receiving distance allowance is 8 meters. 2. is to turn on/o. 3. is show mode. Show 4. the buttons to change the color. White Color Color Show White Color Color Multi-color laser light Seven color with movement Instruction Manual MADE IN CHINA LASER RADIATION, AVOID DIRECT EYE EXPOSURE, DO NOT STARE INTO BEAM OR VIEW DIRECTLY WITH OPTICAL INSTRUMENTS, CALSS IIIa LASER PRODUCT MAX OUTPUT<5 mW WAVELENGTHS 532-650 NM Please only use manufacture provided power supply Built-in timer function:
6h ON / 18h OFF Mode/ Power Laser hole Holder Version: 2018 Made in china Ground Stake PRODUCT SPECIFICATION Laser Classication: Class IIIa Laser Wavelength: Red 635 nm, green 532 nm Power: UL & CUL Adapter 12V, 2A Operation: Indoor/Outdoor Operating Temperature: -15F to 90F
-26C to 32C Projection Coverage: 30 ft x 30 ft Dimensions: 22.5 in x 5.75 in x 5.75 in Cord Length: 3 ft Warranty: One Year Limited 1. Connect the power adapter to the laser light projector. The adapter input voltage is AC120V. 2 . Press the button to switch mode/turn on 3. Press and hold the button to turn o. 4. Built-in timer function: 2h / 4h / 6h / 8h White Color Color the button to control the white laser. switching color mode. automatic color mode circulation 5. Mode Switchover: Steady, ash. 6. are buttons to control light moving mode. There are four mode options:
STATIC, SLOW, FASTER and FASTEST. Motor Speed Down. Motor Speed Up. 7. Press the button , show light laser projector will ash thrice. Reset Timer Function: 2h 4h 6h 8h Press the button , show light laser projector will ash thrice and timer function is canceled. Battery installation:
1. Slide battery cover o. 2. Insert a "CR2025" (3 volt) battery. REMOTE CONTROL If the remote control does not work, check battery. WARNING: This is not a toy and is not intended for use by children.
(A) Do not dispose of the battery in re as the battery may leak and explode.
(B) Do not mix old and new batteries and do not mix alkaline, standard (carbon-zinc), or rechargeable (nickel-cadmium) batteries.
(C) Exhausted batteries are to be removed from the product.
(D) Dispose of battery properly by following directions on battery.
(E) Use CR2025 battery only. Use of other batteries may damage remote control.
(F) Safe for indoor use.
(G) Do not expose the Remote Control to moisture. LASER PROJECTOR FUNCTION Button Mode 1. When turn on the laser and short press the button to switchover to cycle the 7 colors as bellow:
. Red
. Green
. Blue
. White
. Yellow
. Purple
. Azure 2. Press and hold the button to turn o under working status. 3. Short press the button to turn on under power o function, would recover to the mode before powor o stake. SAFETY INSTRUCTIONS Safety Attention 1. Turn o 30 minutes after working 6 hours to last the lifetime of product. 2. This product is mainly used for outdoor with waterproof Ip65. It has excellent radiating ease. Put it far away from the ammable objects or liquids. 3. Please use show light laser projector power adapter to support the light. If you need to change a new adapter, please check the parameter of our adapter before you buy a new one. CAUTION 1. Danger-laser radiation when open. 2. Avoid direct exposure to beam. 3. Avoid direct eye exposure. 4. Laser radiation-do not stare into beam or view directly with optical instruments. 5. The use of optical instruments with this product will increase eye hazard. 6. Use of controls or adjustments or performance of procedures other than those specied herein may result in hazardous radiation exposure. IMPORTANT!
Do not point the show light laser projector to the airplane or up in the sky. FEDERAL COMMUNICATIONS COMMISSION (FCC) STATEMENT FCC Caution: Changes or modications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures: - Reorient or relocate the receiving antenna. - Increase the separation between the equipment and receiver. - Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. Scan & See Me!
www.ishowtree.com
- French:
Le prsentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitationestautorise aux deux conditions suivantes:
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareildoit accepter tout brouillageradiolectriquesubi, mmesi le brouillageest susceptible d'encompromettre le fonctionnement. 11