FCC ID: C3DKF0000001 BLE Key Fob

KF-1001 RV Halo Motion Safety Switch Users Guide The Winegard RV Halo Motion Safety Switch (MSS) is used in conjunction with the RV Halo Voice Control System to safely control slide outs via voice control. Once a voice command has been issued, the RV Halo Voice system continuously sends a command telling the slide out to move as long as the button is pressed on the MSS. If the button is not pressed or the signal is interrupted during slide out operation, the operation is immediately stopped. Example operation:

User issues a command to extend a slide out:

O.K. R.V. - extend the slide out RV Halo Voice responds with:

Please press and hold the safety switch User presses the MSS button and slide out begins to operate and continues as long as the button is pressed. At this point, you are free to walk around the perimeter of the RV verifying safe operation of the slide out. The green LED flashes every second to indicate the unit is transmitting. Pairing the MSS to the RV Halo Voice 1. Put the RV Halo Voice into pairing mode using the RV Halo App on your smart phone / tablet 2. Go to the Admin page 3. Select Bluetooth from the menu 4. Click the "Scan" button to get a list of the Bluetooth devices nearby 5. Press the button on the MSS until it appears in the scan list 6. When pairing is successful, the device will appear in the list of recognized devices 7. If paring was unsuccessful, please factory reset the MSS (see below) and repeat Un-pairing the MSS 1. Open the case using a small screwdriver to pry the two halves of the enclosure apart 2. Press the small silver button on the MSS board for at least 5 seconds 3. Open the RV Halo App 4. Go to the Admin page 5. Select Bluetooth from the menu 6. Select the MSS in the recognized devices list 7. Click Remove Factory Reset Replacing the battery 1. Open the case using a small screwdriver to pry the two halves of the enclosure apart. 2. Press the small silver button on the MSS board for at least 5 seconds 1. Open the case using a small screwdriver to pry the two halves of the enclosure apart. 2. Replace with good quality CR2032 Battery. 3. Verify operation FCC STATEMENTThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following methods:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and devices. Connect the equipment into an electrical outlet on a circuit different from that which the radio receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device and its antenna(s) must not be co-located or operating in conjunction with any other antenna or transmitter except in accordance with FCC multi-transmitter product procedures. IC Regulatory Compliance This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :

(1) Lappareil ne doit pas produire de brouillage;

(2) Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. RF Exposure Compliance This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20 cm between the radiator and your body. Cet quipement est conforme aux limites d'exposition aux radiations IC CNR-102 tablies pour un environnement non contrl. Cet quipement doit tre install et utilis avec une distance minimale de 20 cm entre le radiateur et votre corps.

Date: 2021-6-30 Print Name: Todd Wibben Title: Engineering Manager Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Regarding: FCC ID: C3D-KF0000001 To whom it may concern:

We, the undersigned, hereby authorize Elite Electronic Engineering Inc to act on our behalf in all manners relating to application for equipment authorization with respect to the FCC ID above, including signing of all documents relating to these matters. Any and all acts carried out by the agent on our behalf shall have the same effect as acts of our own. We, the undersigned, hereby certify that we are not subject to a denial of federal benefits, that includes FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 853(a). Where our agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for Certification, as specified by SGS North America, Inc., still resides with Winegard Company. This authorization is valid until further written notice from the applicant. On behalf of Company: Winegard Company Telephone: 319-931-1597 E-mail: twibb@winegard.com Winegard Company

Regarding: FCC /D: C3DKFO000001 To whom it may concern:

Federal Communication Commission Equipment Authorization Branch 7435 Oakland Mills Road Columbia, MID 21046 Date: 2021-08-18 We would like to submit for Certification to FCC: C3DKFO000001. Please find in the following application all related documentation to support this New Single Certification. We would appreciate your prompt attention to the submittal. Applicant Company name: Winegard Company Contact Name: Todd Wibben Address: 3000 Kirkwood St., Burlington JA, 52601, USA Telephone No: 319 931-1597 Fax No: NA Email: twibb wine ard.com FCC ID Number: C3DKFO000001 Topo wisbew Signed by (printed name):

ATTENTION: Federal Communication Commission Equipment Authorization Winegard Company

To:

Federal Communications Commission Office of Engineering and Technology Laboratory Division 7435 Oakland Mills Rd. Columbia MD 21046 From: Winegard Company Regarding: Confidentiality Request regarding application for FCC ID: C3DKF0000001 LONG TERM CONFIDENTIALITY Pursuant to 47 CFR Section 0.459 and 0.457 of the commissions rules, the applicant hereby request confidential treatment of the documents listed below, associated with the certification application referenced above. Schematic(s) Block Diagrams Operational Descriptions Tune up procedures The documents above contain proprietary information not released to the public. Public disclosure of this information may prove harmful to the business of the applicant. SHORT TERM CONFIDENTIALITY Additionally, the applicant requests the following documents be held confidential until the device is marketed or 180 days from the grant date, whichever is less. If the device is marketed within aforementioned days of the Grant Date, the applicant will notify the TCB per FCC KDB 726920 DO1 Confidentiality Request Procedures. External Photos Internal Photos Test Setup Photos User manual(s) Sincerely, Print Name: Todd Wibben Title: Engineering Manager Signature. WJ) On behalf of Company: Winegard Company Telephone: 319-931-1597 E-mail: twibb@winegard.com Winegard Company