FCC ID: WUI-RD030015 Microwave sensor module for LED linkable Shoplight

Specification RD030015 LED LINKABLE SHOPLIGHT Specification File status

] Draft

[ ] Published

] Pending

File name Product specification Version V1.0 Editor Finished date Version Editor Participator Valid from Remark V1.0 Henry Ho 2021-2-8 Niou Specification 0 Amendment 1 Feature RD030015 microwave module, which applies CS-CRD02-XX1 HD021VCR CS3921 colasmart effectively sense human and entity motion self-R&D microwave chip, can Light sensor is available when correspondent component is extra-connected IR remote is available when correspondent component is extra-connected ,and microwave motion sensor distance,hold time,lux threshold etc can be adjusted by IR remote Plate-antenna applied for the sake of max long-distance detection purpose RGB background mode available Working temperature be -20 deg C to +70 deg C

-2060 2 Application Lighting Security Smart home 3 Specication Working voltage Working current Stand-by power Working temperature Frequency Range Microwave power Detection degree Mounting height Sense distance Hold time 7.5-12VDC

<30mA

<0.5W

-20-70 5757MHz-5853MHz

<0.3W 30 - 150 Max.4.5m(ceiling mounted) Very near/Near/Medium/Far OFF/30s/10min/30min 4 Drawing Specification 5.6 Sense distance Distance level Distance range Very near Near Medium Far 1 - 2 2 - 3.5 3.5 - 5 5 - 7 Specification 5.Remark Sense range will be different according to different install height and sense angle Application environment, entity motion velocity etc will effect module sense range ,so above sense range is only for your reference based on ideal circumstance Actual lux threshold is related to your light case material, our value is this specification is only for reference Specification FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS OR CHANGE TO THIS EQUIPMENT. SUCH MODIFICATIONS OR CHANGE COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Increase the separation between the equipment and receiver.

-- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. To satisfy FCC exterior labeling requirements, the following text must be placed on the exterior of the end product Contains Transmitter module FCC ID: WUI-RD030015 The modular must be installed in the host that assign by Company name: Winplus Co., Ltd. Product/PMN: 46 LED LINKABLE SHOP LIGHT Model no./HVIN: LM030015 if other host types used would need further evaluation and possible C2PC if they are not significantly similar to the one tested. IC Information

-English:

(1) This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:

1.This device may not cause interference. 2.This device must accept any interference, including interference that may cause undesired operation of the device.

(2) Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment complies with ISED RF radiation exposure limits set forth for an uncontrolled environment.

-French:

Leprsent appareil est conforme aux CNR d'Industrie Canada applicable aux appareils radio Exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, meme si le brouillage est susceptible d'en compromettre le fonctionnement."

Cet appareil est conforme aux limitesd'exposition de rayonnement RF ISEDC tabliespour un environnement non contrl. Pour satisfaire la ISED extrieur tiquetage, le texte suivant doit tre placlextrieur du produit final Contains metteur module IC:7297A-RD030015. The modular must be installed in the host that assign by Le modulaire doit tre install dans l'hte assign par Nom de la compagnie: Winplus Co., Ltd. Produit/PMN: 46 LED LINKABLE SHOP LIGHT Modle no./HVIN: LM030015 if other host types used would need further evaluation and possible C2PC if they are not significantly similar to the one tested. si d'autres types d'htes utiliss ncessiteraient une valuation plus pousse et un C2PC possible s'ils ne sont pas significativement similaires celui test

Winplus Co., Ltd. Date (2021-02-07) TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Confidentiality Request FCC ID: WUI-RD030015 Pursuant to Sections 0.457(d)(1)(ii) and 0.459 of the Commissions Rules, (Winplus Co. Ltd) hereby requests permanent confidential treatment of information accompanying this application as outlined below:

Schematics Bill of Materials/Parts List Block Diagrams Theory of Operation]

The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457(d)(1)(ii), disclosure of this Application and all accompanying materials will not be made before the date of the Grant for this Application. Yours sincerely,

+852 2798 8932 Company Officer: Benson Leung Telephone Number:

Email:

bensonleung@winplus.net

Winplus Co., Ltd. Date (2021-02-07) TUV SUD BABT TCB Octagon House, Segensworth Road, Fareham, Hampshire, PO15 5RL Dear Sir/Madam, RE: Modular Approval Request for Model:

FCC ID: WUI-RD030015 The following attestation addresses the requirements to support modular approval:

Modular approval requirement

(a) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly Yes No *

The radio module do not has shielded cover, so it was tested with a host for this modular approve application, the host information as below Company name: Winplus Co., Ltd. Product/PMN: 46 LED LINKABLE SHOP LIGHT Model no./HVIN: LM030015

(b) The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal

(c) The module must contain power supply regulation on the module

(d) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections 15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b)

(e) The module must demonstrate compliance in a stand-alone configuration

(f) The module must be labelled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labelling requirements)

(g) The module must comply with all specific rules applicable to the transmitter. The grantee must provide comprehensive instructions to explain compliance requirements

(h) The module must comply with RF exposure requirements Winplus Co., Ltd.

* Please provide a detailed explanation if the answer is No. Yours sincerely, Name: Benson Leung Title: Director