Wireless LAN Module DAUK-W8812 User Manual Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Pentium is trademark of Intel. All copyright reserved. Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA 1 This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains FCC ID: NKRDAUK-W8812. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 2 Industry Canada statement:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:
Cet quipement est conforme aux limites d'exposition aux rayonnements IC ta 5 DNSA-GP1_G02 RF 378 5 1.32%
D896855107D9 D896855109D8 D89685510805 8 DNSA-GP1_G02 RF 360 2 0.56%
D896855107E5 D89685510746 D89685510A60 D89685510A4A s pour un environnement non contrl. Cet quipement doit tre install et utilis avec un minimum de 20 cm de distance entre la source de rayonnement et votre corps. 3 This device is intended only for OEM integrators under the following conditions: (For module device use) 1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes: (Pour utilisation de dispositif module) 1) L'antenne doit tre installe de telle sorte qu'une distance de 20 cm est respecte entre l'antenne et les utilisateurs, et 2) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 2 conditions ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. 4 IMPORTANT NOTE:
In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:
Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains IC: . Plaque signaltique du produit final Ce module metteur est autoris uniquement pour une utilisation dans un dispositif o l'antenne peut tre installe de telle sorte qu'une distance de 20cm peut tre maintenue entre l'antenne et les utilisateurs. Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: ". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 5 Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Caution :
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
(ii) the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall comply with the e.i.r.p. limit; and
(iii) the maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to-point operation as appropriate.
(iv) Users should also be advised that high-power radars are allocated as primary users
(i.e. priority users) of the bands 5250-5350 MHz and 5650-5850 MHz and that these radars could cause interference and/or damage to LE-LAN devices. Avertissement:
Le guide dutilisation des dispositifs pour rseaux locaux doit inclure des instructions prcises sur les restrictions susmentionnes, notamment :
(i) les dispositifs fonctionnant dans la bande 5 150-5 250 MHz sont rservs uniquement pour une utilisation lintrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;
(ii) le gain maximal dantenne permis pour les dispositifs utilisant les bandes 5 250-5 350 MHz et 5 470-5 725 MHz doit se conformer la limite de p.i.r.e.;
(iii) le gain maximal dantenne permis (pour les dispositifs utilisant la bande 5 725-5 825 MHz) doit se conformer la limite de p.i.r.e. spcifie pour lexploitation point point et non point point, selon le cas.
(iv) De plus, les utilisateurs devraient aussi tre aviss que les utilisateurs de radars de haute puissance sont dsigns utilisateurs principaux (c.--d., quils ont la priorit) pour 6 les bandes 5 250-5 350 MHz et 5 650-5 850 MHz et que ces radars pourraient causer du brouillage et/ou des dommages aux dispositifs LAN-EL. 7 Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:
- EN60950-1:2006+A11:2009+A1:2010+A12:2011
-
IEC60950-1:2005 (2nd Edition); Am 1:2009 Safety of Information Technology Equipment
- EN 62311: 2008 / Article 3(1)(a) and Article 2 2006/95/EC)
- Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz-300 GHz)
- EN 300 328 V1.8.1: 2012-06
- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating using wide band modulation techniques;
Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
-
- EN 301 893 V1.7.1: 2012-06
- Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive
-
- EN 301 489-1 V1.9.2: 2011
- Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements
-
- EN 301 489-17 V2.2.1 2012
- Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems
-
In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. 8 esky
[Jmno vrobce] tmto prohlauje, e tento [typ zazen] je ve shod se zkladnmi
[Czech]
poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk Undertegnede [fabrikantens navn] erkl rer herved, at f lgende udstyr [udstyrets
[Danish]
typebetegnelse] overholder de v sentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklrt [Name des Herstellers], dass sich das Gert [Gertetyp] in
[German]
bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti Kesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tp = type
[Estonian]
of equipment] vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]
[Spanish]
cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.
[name of manufacturer] [type of equipment]
[Greek]
1999/5/. Franais Par la prsente [nom du fabricant] dclare que l'appareil [type d'appareil] est conforme
[French]
aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio]
[Italian]
conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar o [name of manufacturer / izgatavotja nosaukums] deklar, ka [type of equipment
[Latvian]
/ iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi iuo [manufacturer name] deklaruoja, kad is [equipment type] atitinka esminius
[Lithuanian]
reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederland Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in s [Dutch]
overeenstemming is met de essentile eisen en de andere relevante bepalingen van richtlijn 1999/5/EG. Malti Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma
[Maltese]
mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. 9 Magyar Alulrott, [gyrt neve] nyilatkozom, hogy a [... tpus] megfelel a vonatkoz alapvet
[Hungarian]
kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Polski Niniejszym [nazwa producenta] owiadcza, e [nazwa wyrobu] jest zgodny z
[Polish]
zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus
[Nome do fabricante] declara que este [tipo de equipamento] est conforme com os
[Portuguese]
requisitos essenciais e outras disposies da Directiva 1999/5/CE. Slovensko
[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in
[Slovenian]
ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky
[Meno vrobcu] tmto vyhlasuje, e [typ zariadenia] spa zkladn poiadavky a vetky
[Slovak]
prslun ustanovenia Smernice 1999/5/ES. Suomi
[Valmistaja = manufacturer] vakuuttaa tten ett [type of equipment = laitteen
[Finnish]
tyyppimerkint] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. 10 Table of Contents 1. INTRODUCTION 12 2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 12 3. SPECIFICATIONS 12 11 1. Introduction Thank you for purchasing the 802.11 a/b/g/n /ac module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. 2. Driver/Utility Installation The driver should have been installed before the TV is shipped from the manufacturer. You can start using its network function without installing driver or utility. This module is associated product for TV host. The following description provides a basic installation for wireless module. For more information about the Wireless Module, please refer to your TV manual. Installing Wi-Fi module :
1. Link cable with USB connector on wireless module 2. Link wireless module with USB connector to PC and install software in wireless module 3. Open the back lid of TV, lock wireless module on internal main board of TV 4. Power supply on internal main-board and allow TV to load fully. 3. Technical spec. Item Main chipset RTL Key specifications Compliance Support 801.11a/b/g/n/ac data rate USA: 2.400 ~ 2.483GHz, 5.15 ~ 5.35GHz, 5.47 ~ 5.725GHz, 5.725 ~ 5.85GHz Frequency Europe: 2.400 ~ 2.483GHz, 5.15 ~ 5.35GHz, 5.47 ~ 5.725GHz range Japan: 2.400 ~ 2.497GHz, 5.15 ~ 5.35GHz, 5.47 ~ 5.725GHz China: 2.400 ~ 2.483GHz, 5.725 ~5.85GHz Transmit center frequency tolerance Transmitted center frequency tolerance within 20 ppm. 12 802.11 Legacy a/b/g/ac DSSS (DBPSK, DQPSK, CCK) OFDM (BPSK, QPSK, 16-QAM, 64-QAM) DSSS (Direct Sequence Spread Spectrum) with DBPSK (Differential Binary Phase Shift Keying 1Mbps), Modulation DQPSK (Differential Quaternary Phase Shift Keying 2Mbps), and technique CCK (Complementary Code Keying 5.5&11Mbps), and OFDM (Orthogonal Frequency Division Multiplexing with BPSK for 6,9Mbps QPSK for 12,18Mbps 16QAM for 24,36Mbps 64QAM for 48,54Mbps) 802.11n a/g OFDM (BPSK, QPSK, 16-QAM, 64-QAM) Operation voltage 5V +/- 5%
FTP TX (the worse average current) 400 mA 650 mA Power AP scanning, no association with AP 188 mA 188 mA consumption
@25 o C@5V
***The maximum current consumption would be impacted by radiation environment and the 802.11n (2.4GHz) 802.11n (5GHz) driver mechanism. 13 802.11a Test Frequencies 6-24_Target 36_Target 48_Target 54_Target 5180 14 14 14 14 5320 14 14 14 14 5500 14 14 14 14 5600 14 14 14 14 5700 14 14 14 14 5825 14 14 14 14 802.11b Test Frequencies 1/2_Target 5.5_Target 11_Target 2412 17 17 17 2472 17 17 17 2484 17 17 17 802.11g Test Frequencies 6-24_Target 36_Target 48_Target 54_Target Output power
(dBm) 2412 15 15 15 15 2437 15 15 15 15 2472 15 15 15 15 802.11n Freq. Range: HT20 Test Freq MCS 0/8 MCS 1/9 MCS 2/10 MCS 3/11 MCS 4/12 MCS 5/13 MCS 6/14 MCS 7/15 5180 13 13 13 13 13 13 13 13 5240 13 13 13 13 13 13 13 13 5320 13 13 13 13 13 13 13 13 5500 13 13 13 13 13 13 13 13 5700 13 13 13 13 13 13 13 13 5745 13 13 13 13 13 13 13 13 5825 13 13 13 13 13 13 13 13 Freq. Range: HT40 Test Freq MCS 0/8 MCS 1/9 MCS 2/10 MCS 3/11 MCS 4/12 MCS 5/13 MCS 6/14 MCS 7/15 5190 13 13 13 13 13 13 13 13 5230 13 13 13 13 13 13 13 13 5270 13 13 13 13 13 13 13 13 14 5510 13 13 13 13 13 13 13 13 5670 13 13 13 13 13 13 13 13 5755 13 13 13 13 13 13 13 13 5795 13 13 13 13 13 13 13 13 Freq. Range: HT20 Test Freq MCS 0/8 MCS 1/9 MCS 2/10 MCS 3/11 MCS 4/12 MCS 5/13 MCS 6/14 MCS 7/15 2412 15 15 15 15 15 15 15 15 2437 15 15 15 15 15 15 15 15 2472 15 15 15 15 15 15 15 15 Freq. Range: HT40 Test Freq MCS 0/8 MCS 1/9 MCS 2/10 MCS 3/11 MCS 4/12 MCS 5/13 MCS 6/14 MCS 7/15 2412 15 15 15 15 15 15 15 15 2437 15 15 15 15 15 15 15 15 2472 15 15 15 15 15 15 15 15 802.11ac (Typical) Freq. Range: 5GHz/VHT80:
Test Freq MCS 0 MCS 1 MCS 2 MCS 3 MCS 4 MCS 5 MCS 6 MCS 7 MCS 8 MCS 9 5210 10 10 10 10 10 10 10 10 10 10 5530 10 10 10 10 10 10 10 10 10 10 5775 10 10 10 10 10 10 10 10 10 10 15 Sensitivity 802.11a Modulation Code Rate IEEE Spec (1Rx dBm) Typical(1Rx dBm) BPSK 1/2 -82 -90 BPSK 3/4 -81 -89 QPSK 1/2 -79 -88 QPSK 3/4 -77 -86 16-QAM 1/2 -74 -83 16-QAM 3/4 -70 -80 64-QAM 2/3 -66 -76 64-QAM 3/4 -65 -74 802.11b Modulation EEE Spec (1Rx dBm) Typical/Maximum (1Rx dBm) DBPSK not specified -95 DQPSK not specified -92 CCK not specified -90 802.11g Modulation Code Rate IEEE Spec (1Rx dBm) Typical/Maximum (1Rx dBm) BPSK 1/2 -82 -89 BPSK 3/4 -81 -89 QPSK 1/2 -79 -87 QPSK 3/4 -77 -85 16-QAM 1/2 -74 -82 16-QAM 3/4 -70 -79 64-QAM 2/3 -66 -75 64-QAM 3/4 -65 -73 802.11ng Modulation Code Rate IEEE Spec (1Rx dBm) Typical/Maximum (2Rx dBm) HT20
(MCS0) BPSK 1/2 -82 -90
(MCS1) QPSK 1/2 -79 -86
(MCS2) QPSK 3/4 -77 -84
(MCS3) 16-QAM 1/2 -74 -81
(MCS4) 16-QAM 3/4 -70 -78
(MCS5) 64-QAM 2/3 -66 -73
(MCS6) 64-QAM 3/4 -65 -72
(MCS7) 64-QAM 5/6 -64 -70 16 HT40
(MCS0) BPSK 1/2 -79 -87
(MCS1) QPSK 1/2 -76 -84
(MCS2) QPSK 3/4 -74 -82
(MCS3) 16-QAM 1/2 -71 -79
(MCS4) 16-QAM 3/4 -67 -76
(MCS5) 64-QAM 2/3 -63 -72
(MCS6) 64-QAM 3/4 -62 -69
(MCS7) 64-QAM 5/6 -61 -68 802.11na Modulation Code Rate IEEE Spec (1Rx dBm) Typical/Maximum (2Rx dBm) HT20
(MCS0) BPSK 1/2 -82 -90
(MCS1) QPSK 1/2 -79 -88
(MCS2) QPSK 3/4 -77 -86
(MCS3) 16-QAM 1/2 -74 -83
(MCS4) 16-QAM 3/4 -70 -79
(MCS5) 64-QAM 2/3 -66 -75
(MCS6) 64-QAM 3/4 -65 -74
(MCS7) 64-QAM 5/6 -64 -70 HT40
(MCS0) BPSK 1/2 -79 -88
(MCS1) QPSK 1/2 -76 -85
(MCS2) QPSK 3/4 -74 -82
(MCS3) 16-QAM 1/2 -71 -79
(MCS4) 16-QAM 3/4 -67 -76
(MCS5) 64-QAM 2/3 -63 -72
(MCS6) 64-QAM 3/4 -62 -70
(MCS7) 64-QAM 5/6 -61 -68 802.11ac Modulation Code Rate IEEE Spec (1Rx dBm) Typical/Maximum (1Rx dBm) VHT80
(MCS0) BPSK 1/2 -76 -85
(MCS1) QPSK 1/2 -73 -82
(MCS2) QPSK 3/4 -71 -80 17
(MCS3) 16-QAM 1/2 -68 -77
(MCS4) 16-QAM 3/4 -64 -73
(MCS5) 64-QAM 2/3 -60 -69
(MCS6) 64-QAM 3/4 -59 -67
(MCS7) 64-QAM 5/6 -58 -65
(MCS8) 256-QAM 3/4 -53 -61
(MCS9) 256-QAM 5/6 -51 -58 0o ~ 60o C
-20o ~ 80o C Operation temperature Storage temperature Antenna Information:
Model Peak gain ( dBi ) Type Connector 2400~2483.5MHz 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz 81.EEW15.GFV PIFA U.FL
-3.77
-4
-3.5
-3.56
-4.31 18