FCC ID: NKRRXAM-JD1 802.11 abgn/ac/ax Access Point

RXAM-JD1 Access Point User Manual 1 Table of Contents 1 INTRODUCTION...................................................................................................................5 1.1 1.2 PRODUCT APPEARANCE AND LAYOUT...................................................................................5 LED LIGHT GUIDE..................................................................................................................5 2 MOUNTING THE ACCESS POINT......................................................................................6 2.1 2.2 2.3 2.4 2.5 2.6 ACCESSORIES FOR INSTALLATION..........................................................................................6 MAIN BRACKET.......................................................................................................................6 CEILING MOUNTING................................................................................................................7 PENDANT MOUNT.................................................................................................................10 WALL MOUNTING..................................................................................................................11 CHOOSING A POE INJECTOR FOR THE DEVICE....................................................................12 3 PRODUCT SPECIFICATIONS...........................................................................................13 2 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device is going to be operated in the 5.155.25GHz frequency range, it is restricted to use in indoor environments only. This device is restricted for indoor use. Professional installation is required. IMPORTANT NOTE:

FCC Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 24 cm between the radiator & your body. 3 FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. 4 1 Introduction 1.1 Product Appearance and Layout Front Back 1.2 LED Light Guide The LED indicator is located on the top right corner of the Access Point and displays the operational status of the device. Refer to the guide below for LED status descriptions:

LED Status Description No light Device is unpowered or LED indicator is disabled. Amber An abnormality has occurred White Device is ready and fully operational Rear 5 2 Mounting the Access Point This section describes how to mount the Access Point. 2.1 Accessories for Installation Main bracket 1 Adapter brackets 2 Wall screws 3 (8X25) Wall anchors 3 (BH(2#)M32425 TPA(6.3, 1.9)) M4 screws 4 (PH+SW+WM4-0.7x8 W=8 CR3/Zn) M3 screws 4 (PH+SW+WM3-0.5x6 W=8 Ni) 2.2 Main Bracket The main bracket enables the Access Point to be installed onto ceilings, walls, or pendant mounted. The features of the bracket are listed below:

6 2.3 Ceiling Mounting Refer to the steps below to mount the Access Point onto T-bar ceilings. 1. Use the C-shaped structure to attach the two adapter brackets to either side of the T-bar, making sure that the arrows on the brackets are facing opposite directions. 7 2. After the adapter brackets are affixed onto the T-bar, slide the brackets in the direction of the arrows on the brackets until they are securely attached to each other. Refer to the images below for how the adapter brackets should fit. 3. Align the screw holes on the adapter brackets with the holes on the main bracket (refer to section 2.2), then use four M3 screws to screw the main bracket to the adapter brackets. 4. Align the screw holes on the main bracket with the corresponding holes on the back of the Access point, then use four M4 screws to attach the main bracket to the Access Point. 8 Note: Make sure the arrow on the main bracket is aligned so that it is pointing toward the top side of the Access Point. 5. Once the aforementioned steps are complete, the side-view of the completed setup should look like the image below:

9 Refer to the steps below to mount the Access Point to a pendant mount. 1. Align the pendant mount screw holes on the main bracket with the holes 2.4 Pendant Mount on the pendant mount. 2. Use the pendant mount screws (M4 screws; length: 12.7 mm; material:

normal aluminum, non-surface treated) to securely affix the main bracket to the pendant mount. 3. Align the screw holes on the main bracket with the corresponding holes on the back of the Access point, then use four M4 screws to attach the main bracket to the Access Point. Note: Make sure the arrow on the main bracket is aligned so that it is pointing toward the top side of the Access Point. 10 2.5 Wall Mounting Refer to the steps below to mount the Access Point to a wall. 1. Place the main bracket against the installation location on the wall. Use a pen or pencil to mark the points on the wall where the wall mounting holes are aligned. 2. Use a power tool to drill holes in the marked locations, then insert the wall anchors into the holes. 3. Use a power tool or a screwdriver to screw the wall mounting screws into the wall anchors. Leave about one-third of the screw length sticking out of the wall. 4. Align the screw holes on the main bracket with the corresponding holes on the back of the Access point, then use four M4 screws to attach the main bracket to the Access Point. Note: Make sure the arrow on the main bracket is aligned so that it is pointing toward the top side of the Access Point. 5. Align the wall mounting holes on the main bracket with the wall screws, then hook the Access Point onto the wall screws. 11 2.6 Choosing a PoE Injector for the Device A Power over Ethernet (PoE) injector is used to power the RXAM-JD1 Access Point. PoE injectors used with the AP must comply with the criteria listed below:

1. The "Data In" and "Data & Power out" ports on the injector must be qualified as Safety ExtraLow Voltage (SELV) circuits. 2. The circuits in the injector must have IEC 60950-1 and IEC 60950-1 Electrical Energy Source Class 1 (ES1) certification. The injector must have a nominal output voltage of 56 Vdc and a maximal input current of 0.6 A. A statement indicating that the injector is a Limited Power Source

(LPS) rated power supply must also be indicated on the label of the PoE injector. The SELV ports on the injector must only be connected to other SELV (or ES1) interfaces on other equipment. 12 3 Product Specifications Outer Dimensions 220 220 42 (mm) Marvell CN9130-1600-NG-AUS-G SDRAM: DDR4; 1 GB 2 NAND Flash: 512 MB SPI NOR Flash: 4 MB Dual-band Antenna 4 2.4 GHz Antenna 1 Six-layer PCB; dimensions: 191.7 145.75 1.6 (mm) Marvell 88E2110-A0-BWS4C000 2 NXP 88W9064-A1-BWP2C000 2 10/100/1000/2500 Mbps auto-

negotiation Ethernet ports 2 Supports PoE 802.3at CPU Memory Antennas PCB mGiga PHY RF IC (2G/5G) Ethernet port 13

Model: RXAM-JD1 FCC ID: NKRRXAM-JD1 Input Voltage Range: PoE 802.3at 50V-57V === 600mA This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) this device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation SIN:XXXXYWWDSSSSCEE Ethernet0 MAC:XXXXXXXXXXXX Asset No.:XXXXXXX RFO MAC:XXXXXXXXXXXX Made in Taiwan re @=|

LISTED LTE. E252240

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Confidential Letter Date: 2020/5/27 Federal Communications Commission 7435 Oakland Mills Road Columbia MD 21046 Subject: Request for Confidentiality FCC IDNKRRXAM-JD1 To Whom It May Concern:

Long Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request confidential treatment of information accompanying this application as outlined below:

Block Diagrams Schematics Operational Description The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We understand that pursuant to Rule 0.457, disclosure of this Application and all accompanying documentation will not be made before the date of the Grant for this application. Short Term Confidentiality Pursuant to Sections 0.457 and 0.459 of the Commissions Rules, we hereby respectfully request short-term confidential treatment of information accompanying this application as outlined below until 180 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

External Photos Internal Photos Test Setup photos Users Manuals Sincerely, Applicants company name

: Wistron NeWeb Corporation Applicants company address

: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Signature

Name E-Mail Tel Fax

: Lulu Lin

lulu.lin@wnc.com.tw

: 886-3-6667799

: 886-3-666-7323

Wistron NeWeb Corp. AGENCY AUTHORIZATION LETTER Date: 2020-07-31

|, William Su, am senior compliance manager for Wistron NeWeb Corp. hereby authorize the following to act on our behalf, as our agent, in all matters relating to all processes required according to FCC/IC Approval for Wistron NeWeb Corp. products. Barry Chen, Yuanwei Lin, Lulu Lin, Eva IM Huang, Kelly Tsai This Letter of Authorization will expire on 7/31/2021, unless earlier revoked in writing. If you have any questions regarding the authorization, please don t hesitate to contact us. Sincerely, Sincerely, fhyo ff; :

[L iam Su William Su / Senior Compliance Manager Wistron NeWeb Corp. Tel: 886-3-6667799 Ext 6688 E-mail: William.Su@wnc.com.tw

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Power of Attorney Date: 2020/5/27 I hereby have entrusted the following person to be a proxy regarding application for Type Sporton International Inc. Address Name Job Title e-mail

: No.8, Lane 724, Bo-ai St., Jhubei City, HsinChu County 302, Taiwan, R.O.C.

: Leo Huang

: Manager

: Leohuang@sporton.com.tw I am therefore responsible for the contents of the application. FCC ID: NKRRXAM-JD1 Dear Sir, Certification. Sincerely, Applicants company name

: Wistron NeWeb Corporation Applicants company address

: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Signature

: Lulu Lin

lulu.lin@wnc.com.tw

: 886-3-6667799

: 886-3-666-7323 Name E-Mail Tel Fax

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Professional Installation Declaration Date: 2020/5/27 FCC IDNKRRXAM-JD1 To Whom It May Concern:

Please be advised that due to the unique Market and function targeted by this product, this product will need special trained professional in configuring and installing the product. We hereby declare that the product will be distributed through controlled distribution channel which has special trained professional to install this product and will not be sold directly to the general public through retail store. Sincerely yours, Applicants company name

: Wistron NeWeb Corporation Applicants company address

: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Signature

Name E-Mail Tel Fax

: Lulu Lin

lulu.lin@wnc.com.tw

: 886-3-6667799

: 886-3-666-7323

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan SDoC Attestation Letter Date: 2020/5/27 We Wistron NeWeb Corporation, as the grantee of this project (FCC ID: NKRRXAM-JD1 /

Brand Name: WNC / Model No.: RXAM-JD1), would like to declare that the composite portion has been authorized under the Supplier's Declaration of Conformity procedures

(Sporton report No.: FD052068, FCC designation number: TW1096). The final product shall consequently comply with the FCC rule applied for SDoC Procedure. Regards, Sincerely, Name E-Mail Tel Fax Applicants company name

: Wistron NeWeb Corporation Applicants company address

: 20 Park Avenue II, Hsinchu Science Park, Hsinchu 308 Taiwan Signature

: Lulu Lin

lulu.lin@wnc.com.tw

: 886-3-6667799

: 886-3-666-7323