FCC ID: NKR-P2 Bluetooth Adaptor

DBUB-P2 Bluetooth Adapter Users Manual This document provides safety instructions and describes the specifications. Read this document carefully before installing to ensure your safety and product performance. Federal Communication Commission (FCC) Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

-

-

-

-

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA. Operation of this device is restricted to indoor use only This device is intended only for OEM integrators under the following conditions:

1. The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2. The transmitter module may not be co-located with any other transmitter or antenna, 3. For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate FCC authorization. End Product Labeling This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following:

Contains FCC ID: NKR-P2. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Antenna information Type PIFA Connector Peak Gain(dBi) NO 2.68 Industry Canada statement:

This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. D claration d'exposition aux radiations:

Cet quipement est conforme Canada limites d'exposition aux radiations dans un environnement non contr l. Cet quipement doit tre install et utilis distance minimum de 20cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions:

1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les int grateurs OEM dans les conditions suivantes:

1) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product (including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling The final end product must be labeled in a visible area with the following:

Contains IC: 4441A-P2. Plaque signal tique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante: "Contient des IC: 4441A-P2". Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Antenna information Type PIFA Connector Peak Gain(dBi) NO 2.68 Taiwan statement:

Informaci n M xico La operacin de este equipo est sujeta a las siguientes dos condiciones: (1) es posible que este equipo o dispositivo no cause interferencia perjudicial y (2) este equipo o dispositivo debe aceptar cualquier interferencia, incluyendo la que pueda causar su operacin no deseada. Caution:

Be aware of the following limits before using the Bluetooth Adaptor. Do not subject the Bluetooth Adaptor to high temperatures, direct sunlight or moisture. Do not bend, or subject the Bluetooth Adaptor to strong impacts. Do not disassemble or alter the Bluetooth Adaptor in any way. Do not attempt to install the Bluetooth Adaptor in any incompatible device. Do not remove the Bluetooth Adaptor from the TVs during operations. Data transmitted and received over radio waves may be intercepted and monitored. To avoid malfunctions caused by radio wave interface, keep the TV away from the devices such as other wireless devices, microwaves and the devices that use 2.4 GHz signals when using the Bluetooth Adaptor. Depending on the area, this Bluetooth Adaptor may not be available. Setup the Bluetooth connection The Bluetooth adapter is pre-installed in the TV set. No extra installation steps are required for users. Follow the steps below to start using the feature of this adapter:

1. Turn on your TV. 2. Switch to the channel that delivers 3D contents. If you are watching a disc with 3D contents, you will also need to activate your player for playing the disc. 3. Turn on your 3D glasses. 4. The 3D glasses will pair with this Bluetooth adapter automatically and are now ready for use. Specification Item Contents Frequency range:

2402-2480MHz Channel spacing:

1MHz Channel List:

79 channels Modulation type:

GFSK, /4 DQPSK, 8DPSK Modulation technology:

GFSK Conducted output power:

10dBm Antenna type:

PIFA antenna Antenna gain(dBi):

Antenna connector:

2.68 NA Operating temperature:

0~60 Power supply 3.3Vdc from host

* Transfer rate are theoretical values; however, actual communication rate will vary according to communication environment or connected equipment.