Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 1 OF 26 UMC-SKVM2 User Manual Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 2 OF 26 Revision History Issue Date Version Description 2018/03/05 1.0 Initial Issued 2018/07/09 1.1 Update page 16,24,25 2018/07/20 1.2 Update page 16,24 Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 3 OF 26 Contents 1. Introduction ............................................................................................................................................ 4 2. Test Setup Configuration ....................................................................................................................... 5 2.1 Power Supply and Debug Console Connection ......................................................................... 5 i. Top view of UMC-SKVM2 ................................................................................................... 5 ii. Bottom view of UMC-SKVM2 ............................................................................................. 6 iii. Interface board ....................................................................................................................... 7 iv. Connection between interface board and UMC-SKVM2 ...................................................... 8 2.2 2.3 Antenna Connection................................................................................................................. 12 Hardware Component Introduction ......................................................................................... 13 3. LTE B13 Test and ZB Test ................................................................................................................... 16 Install Qualcomm USB driver ................................................................................................ 17 3.1 Confirm the Qualcomm device .............................................................................................. 17 3.2 Enter ADB shell ....................................................................................................................... 18 3.3 3.4 ZigBee Test Command ............................................................................................................ 19 Interfaces .............................................................................................................................................. 20 4. 4.1 4.2 4.3 Qualcomm HS-USB MDM Diagnostics 90B2 (COM port) .................................................... 20 Qualcomm HS-USB WWAN Adapter 90B2 ........................................................................... 21 Qualcomm HS-USB Modem 90B2 ......................................................................................... 21 5. Federal Communication Commission Interference Statement ............................................................ 23 6. Appendix I ........................................................................................................................................... 26 Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 4 OF 26 1. Introduction This User Manual of UMC-SKVM2 is to describe how to use the following sections for lab test by specific qualified engineers or technicians. Furthermore, this SMCC (Smart Metering Communication Card) is NOT intended for commercial use but designed as part of Smart Meter product which mainly provides 4G LTE WAN access. For the procedure of SMCC installation and set-up for testing and operating, the information is described as well in the following description. FCC Interference Statement This module complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This module may not cause harmful interference and (2) this module must accept any interference received, including interference that may cause undesired operation. Radiation Exposure Statement This module complies with FCC radiation exposure limits set forth for an uncontrolled environment. This module should be installed and operated with minimum distance of 20cm between radiator and human body. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the device. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 5 OF 26 2. Test Setup Configuration 2.1 Power Supply and Debug Console Connection i. Top view of UMC-SKVM2 LTE module Debug USB connector Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 6 OF 26 ii. Bottom view of UMC-SKVM2 SIM slot Make sure to insert the SIM card for LTE test. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 7 OF 26 iii. Interface board Make sure the jumpers are in right position. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 8 OF 26 iv. Connection between interface board and UMC-SKVM2 OFF ON Interface Board 30 pin Meter connector UMC-SKVM2 Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 9 OF 26 Power switch Interface Board AC-DC 5V Adaptor USB Debug Port Console Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 10 OF 26 Internal antenna Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 11 OF 26 External antenna Power on Sequence:
I. Connect UMC-SKVM2 to interface board II. Attach AC-DC Adaptor & USB Debug Port Cable III. Turn on by the power switch IV. Wait for 20 seconds when system ready Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 12 OF 26 2.2 Antenna Connection Connect to LTE Antenna Connector for ZigBee conducted test Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 13 OF 26 2.3 Hardware Component Introduction UMC-SKVM2 AC-DC 5V Adaptor Interface Board UMC-SKVM2 LTE internal antenna Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 14 OF 26 Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 15 OF 26 UMC-SKVM2 LTE external antenna with honey board Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 16 OF 26 3. LTE B13 Test and ZB Test It is recommended to use Anritsu MT8821C for RF conductive tests.setc In the field, please use Qualcomm tool, QXDM, and AT-command to control device and log device message. For LTE radiation tests, the LTE antenna gain lists below. LTE internal Antenna (Mode A) Band 13 Peak Gain: maximum antenna gain allowed is 2.74dBi LTE external Antenna (Mode B) Band 13 Peak Gain: maximum antenna gain allowed is 1.66dBi Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 17 OF 26 3.1 Install Qualcomm USB driver Install the Qualcomm USB driver & ADB driver 3.2 Confirm the Qualcomm device Confirm the Android Device Android Comosite ADB interface Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 18 OF 26 3.3 Enter ADB shell Command in Command Prompt:
adb shell Command in adb shell:
cat /etc/gridnet-release Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 19 OF 26 3.4 ZigBee Test Command Enter Zigbee control mode:
ember-mfgtool Set mfg start:
mfg start 1 Freq. channel setting:
mfg channel set 11 Channel Low : 11 -> CH11 Channel Mid : 18 -> CH18 Channel High : 25 -> CH25 Power level/mode setting:
mfg power set -3 mode 2 Single tone output:
mfg tone start Single tone output stop:
mfg tone stop Modulation signal output:
mfg stream start Modulation signal output stop :
mfg stream stop Exit:
<Ctrl>+<X>
<Enter>
Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 20 OF 26 4. Interfaces This SMCC offers following interfaces to communicate with module. Before using USB emulated ports, it requires to install the Qualcomms USB driver on your windows PC in advance. After driver installation is finished, device manager will show below USB emulated COM ports. 4.1 Qualcomm HS-USB MDM Diagnostics 90B2 (COM port) This port is created for modem debugging purpose and used by Qualcomm PC tools to communicate with the module. Qualcomms tool is protected by Qualcomm License. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 21 OF 26 4.2 Qualcomm HS-USB WWAN Adapter 90B2 This port is created as a virtual network interface which could be used by PC to connect with Internet. 4.3 Qualcomm HS-USB Modem 90B2 This port is also called as modem port. Testers could use PC terminal tool to connect with the port and send AT commands to control modem directly. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 22 OF 26 Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 23 OF 26 5. Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio technician for help. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 24 OF 26 FCC Caution:
Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This device is intended only for OEM integrators under the following conditions:
1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and the maximum antenna gain allowed for use with this device is +2.74 dBi with internal antenna and +1.66 dBi with external antenna. 2) The transmitter module may not be co-located with any other transmitter or antenna. As long as 2 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. IMPORTANT NOTE:
In the event that these conditions cannot be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID cannot be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product
(including the transmitter) and obtaining a separate FCC authorization. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 25 OF 26 End Product Labeling:
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The final end product must be labeled in a visible area with the following: Contains FCC ID:
NKR-CB1GSKVM2. The grantee's FCC ID can be used only when all FCC compliance requirements are met. Manual Information to the End User:
The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Wistron Neweb Corporation Proprietary & Confidential Design Document Subject: UMC-SKVM2 User Manual REV: 1.2 PAGE 26 OF 26 6. Appendix I Environmental Setup 1. Windows 7 x64 The environment setup was tested on Windows 7 x64 successfully. 2. USB driver QUD.WIN.1.1 Installer will be needed to be installed for the following ports:
Qualcomm HS-USB MDM Diagnostics 90B2 Qualcomm HS-USB MDM WWAN Adapter 90B2 Qualcomm USB Composite Device 90B2 QDSS Data 90B2 Qualcomm HS-USB Modem 90B2 3. ADB driver http://adbdriver.com/
4. ADB shell Wistron Neweb Corporation Proprietary & Confidential