FHD251E IP Camera User Manual Table of Contents FCC STATEMENT ............................................................................... 1 SAFETY PRECAUTIONS ..................................................................... 3 1 2 3 INTRODUCTION ...................................................................... 5 PACKAGE CONTENTS ............................................................... 5 KEY FEATURES ....................................................................... 6 HARDWARE OVERVIEW ........................................................... 7 1.1 1.2 1.3 START USING THE CAMERA .................................................. 11 ASSEMBLING THE CAMERA & THE WIRELESS ADAPTER ................ 11 CONNECTING THE CAMERA TO A NETWORK............................... 14 REBOOTING AND RESETTING THE CAMERA ................................ 15 2.1 2.2 2.3 APPENDIX ............................................................................. 16 SPECIFICATIONS AND COMPLIANCE .......................................... 16 TROUBLESHOOTING .............................................................. 18 OBTAINING TECHNICAL SUPPORT ............................................ 19 DISPOSAL INSTRUCTIONS ....................................................... 19 3.1 3.2 3.3 3.4 FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 1 FCC Radiation Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator & your body. 2 Safety Precautions Please read this user manual before operating this product. The information contained in this document is subject to change without notice. Features or specifications may be different depending on the type of product model purchased. Safe Use of This Product Carefully follow the warnings and safety notices presented within this manual. Please pay special attention to the following indications of potentially hazardous situations:
Warning: Indicates a hazardous situation, which, if not avoided, could result in serious injury. Caution: Indicates a situation, which, if not avoided, could damage this product or other devices. Note: Indicates additional user information to make the user aware of possible problems and to help the user understand, use, and maintain the product. 3 This product needs only an occasional wipe with a dry cloth. Avoid high-moisture conditions and keep away from liquids and humidity. Do not install or use the product where it is exposed to direct sunlight or heat. Care must be taken when using the device in close proximity to personal medical devices, such as pacemakers and hearing aids. Do not use this product in environments where there are potential explosion hazards. The product must be placed horizontally on a hard, flat surface or installed firmly with wall-mount kits. Do not place the product where it may be subject to physical shock or vibration or where the product may drop, topple, slide, or shake; this may cause personal injury or damage to the product. If lightning is expected, or the product is not going to be used for a long period of time, unplug the power cord from the unit. The use of electronic transmitting devices in aircraft, hospitals, and petrol stations is forbidden. Please follow the rules and warnings in these conditions. The product must ONLY be used with the power supply cord and power adapter supplied by the manufacturer. Openings on the housing of the product are required for ventilation. Do not block or obstruct the air flow through these openings. Do not operate the product on a soft surface such as carpet, rug, bed, etc. 4 1 Introduction 1.1 Package Contents Thank you for purchasing this product. Before using the FHD251E IP Camera (referred to in this manual as the camera), please confirm that the packaging includes the following items and accessories:
FHD251E IP Camera WFB100S Wireless Power over Ethernet (PoE) Adapter (referred to in this manual as the wireless adapter) Camera bracket & screws User manual 5 Full HD 1080p @ 30 fps (1920 1080) Visualization in total darkness up to 15 meters Switchable IR cut filter for vivid color during the daytime Light sensor to automatically detect ambient light conditions 1.2 Key Features FHD251E Motion detection Waterproof IP65 Digital PTZ HDR LDC Power over Ethernet Easily connects to home-network environments Internal Power Module, V-in: 120 V, V-out: 48 V WFB100S Wi-Fi: 2.4 GHz IEEE 802.11n 2 2 WPS for easy network pairing RJ45 Ethernet connection IEEE 802.3afcompliant 6 1.3 Hardware Overview FHD251E Front view Cap Light guide Speaker Rear view Cap Microphone 7 IR lens Status LED Ball joint LED functions LED Color Red Blue Green Green Green Function Description Pre-boot Operating system booting Post-boot; no network connectivity Standby; encoder recording locally Streaming to the network Status Solid on if power OK Blinking 1 Hz, 50% duty cycle Blinking 4 Hz, 50% duty cycle Solid on Blinking 1 Hz, 50% duty cycle 8 WFB100S Light guide Ethernet port Status Solid on Fast blinking, 4 Hz, 50%
duty cycle Slow blinking, 1 Hz, 50%
duty cycle Off Button LED functions:
Blue LED color Function description Normal operation and Blue connected Power up and during firmware download Firmware download complete but no connectivity WPS mode activated Blue Blue 9 10 2 Start Using the Camera 2.1 Assembling the Camera & the Wireless Adapter Follow the steps below to set up your camera hardware and ensure that the camera operates properly. 1. Attach the camera bracket to the camera by gently tightening it onto the camera. Caution:
Ensure that the camera is securely fixed;
otherwise it may fall and cause damage or injury. 11 2. Remove the grommet and the cap on the rear side of the camera. 3. Insert the Ethernet cable into the cameras Ethernet port and connect the other end to the wireless adapter, then place the grommet back and screw on the cap. 12 4. Plug the wireless adapter into an electrical outlet. 13 2.2 Connecting the Camera to a Network 1. After inserting the Ethernet cable into the cameras Ethernet port and connecting the other end to the wireless adapter, the adapter will be able to supply power to the camera when plugged into a wall outlet. 2. Press the WPS button of the AP that you want to connect to, then press the adapters button to connect to the AP. Once the Wi-Fi of the wireless adapter is paired with an AP via WPS, the camera then connects to the network through the wireless adapter. 3. The IP camera has been successfully added to your network after the connection between the wireless adapter and your AP is established. The installation process is now complete. Now you may start using the camera. 14 2.3 Rebooting and Resetting the Camera and the Wireless Adapter 1. Press and hold the button on the wireless adapter for 0 seconds3 seconds or over 20 seconds. 2. For factory reset, press and hold the button on the wireless adapter for 10 seconds20 seconds. 15 3 Appendix 3.1 Specifications and Compliance Model FHD251E Resolution IR LEDs IR LED Illumination Range Sensitivity Sensors Lens Status LEDs FOV Operating Voltage Ambient Operating Temperature Storage Temperature Dimensions Weight IP Rating PoE 1080p (1920 1080) @ 30 fps 12 pcs. 15 meters 0 lux when IR LED is on (black & white video). CMOS 1/3 4 megapixels 6 glass 1 pc (Tri colorred, blue, and green) 138 (D) V-in: 48 V (DC) 40 C to +65 C 40 C to +65 C 77.05 mm 115.97 mm 79.2 mm 324 g IP65 IEEE 802.3af 16 Model WFB100S CPU 2.4 GHz SPI Flash Memory DDR3 Status LEDs RJ45 Operating Voltage Ambient Operating Temperature Storage Temperature Dimensions Weight RTL8196E RTL8192ER 32 MB 128 MB 1 pc (Single colorblue) 10/100 mbps V-in: 120 V (AC), V-out : 48 V (DC) 0 C to +50 C 40 C to +65 C 91 mm 57 mm 44 mm 124 g 17 3.2 Troubleshooting Solution 1. Check the Ethernet connection status. 2. Plug out and plug in once to reboot the wireless adapter. 1. Check the Ethernet connection status. 2. Restart WPS pairing and make sure the AP router is in signal range and is in WPS mode. Problem The button has no response. The LED blinks slowly after the WPS process is completed. 18 3.3 Obtaining Technical Support While we hope your experience with the FHD251E IP Camera is enjoyable, you may experience some issues or have questions that this User Manual has not answered. If you have a problem with the FHD251E IP Camera, please contact us at:
Tel.:+886 3 666 7799 Ext.: 3214 E-mail: Jacky.Liu@wnc.com.tw Mobile: +886 916 324 575 Website: www.wnc.com.tw 3.4 Disposal Instructions WNC is committed to responsible environmental stewardship. Please dispose of this product in accordance with the local laws and regulations in your area. Contact your local waste-disposal authorities for relevant instructions. 19