FCC ID: NKR-TR1V1-IDU Verizon 5G Extender

Verizon 5G Extender TR1V1 User Guide Version 1 Federal Communication Commission Interference Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This transmitter must not be co-located or operating in conjunction with any other antenna or FCC Caution:

transmitter. WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. i RF Exposure Statement To comply with FCC RF exposure compliance requirements, the antenna used for this transmitter must be installed to provide a separation distance of at least 32 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. ii Table of Contents Chapter 1 Introduction ..................................................................................................................................... 1 1.1 Unboxing Information........................................................................................................................... 1 1.2 Front Panel ............................................................................................................................................ 2 1.3 Back Panel ............................................................................................................................................ 3 1.4 Bottom Panel ........................................................................................................................................ 4 1.5 Side Panel ............................................................................................................................................. 4 1.6 Mounting Bracket ................................................................................................................................. 5 Chapter 2 Mounting the 5G Extender ........................................................................................................... 7 2.1 Window Mounting ................................................................................................................................. 7 2.2 Wall Mounting ....................................................................................................................................... 9 Chapter 3 Product Specifications................................................................................................................ 12 iii This chapter includes a list of items included with the TR1V1 5G Extender and a description of the Inside the product package for the TR1V1 5G Extender, you should find the following items:

Chapter 1 Introduction user interface and ports on the device. 1.1 Unboxing Information Extender AC adapter Window mounting bracket One alcohol swab Cable ties Cable clips (with adhesive) Window wedges (with adhesive) Anchors and metal screws for wall mounting Installation location labels (with adhesive) 1 1.2 Front Panel An LED indicator is located in the top-left corner of the Extenders front panel. LED Light Guide Device Status Description LED Status Booting up The Extender is powered and in the process of booting up. Solid: White Ready to pair The Extender is ready to be paired with the 5G nodes. Blinking: Blue Ready to scan The Extender is connected to the 5G nodes. Solid: Blue Scanning The Extender is scanning the signal strength from the 5G nodes. Soft Blink: White Paired: Good Signal The signal strength from the 5G nodes is good. Solid: Green Paired: Poor Signal The signal strength from the 5G nodes is poor. Solid: Yellow 2 Paired: No/Bad Signal There is no signal from the 5G nodes. Solid: Red Regular usage The Extender is working normally. Off Error An error has occurred (ex. pairing/FW issue) Blinking: Red FW Update /

Reset The Extender is ready to reboot after a FW update. Fast Blink: White

(Occurs during the 2 seconds prior to reboot/power off) 1.3 Back Panel Scan the QR code on this label with the Installer app to enable the receiver to establish a 1. Product label and QR code connection with the Extender. 2. Mounting head The mounting head fits into the installation slot on the mounting bracket. 3 Plug the AC adapter into this jack to power the Extender. The securing screw for the mounting bracket should be fastened into one of these holes. 1.4 Bottom Panel 1. DC jack 2. Screw holes 1.5 Side Panel 4 Use this button to scan for 5G signals from 5G nodes located outdoors. You may also press and hold this button for 3 seconds to switch between regular mode and installation mode. In addition, pressing and holding this button for more than 20 seconds triggers the factory reset process. The raised nubs on the mounting head fit into the dimple holes on the inside of the mounting 1. Scan button 2. Raised nubs brackets installation slot. 1.6 Mounting Bracket 5 1. Mounting holes 2. Bracket cover mounting bracket to a wall. 3. Installation slot performance purposes. 4. Securing screw 5. Hole for AC adapter installed on the mounting bracket. 6. Hole for securing screw Wall screws are screwed through these mounting holes during wall installation. This cover is attached to the top of the brackets base. Remove the cover before attaching the Install the mounting head of the Extender into this slot. Once installed in this slot, the Extender can be rotated to either the left or to the right if the central position is not adequate for Once the desired alignment for the Extender is found, this screw is used to ensure that the Extender is securely attached to the mounting bracket. This hole enables the cable from the AC adapter to connect to the DC jack when the Extender is This hole should be aligned with one of the screw holes on the mounting head of the Extender. 6 Chapter 2 Mounting the 5G Extender 2.1 Window Mounting This section describes how to mount the 5G Extender onto window glass or walls. 1. Use the provided alcohol swab to clean the area around the label, and wait for the alcohol to dry. 2. Peel off the protective backing on the Gecko Tape on the base of the mounting bracket, then affix the bracket onto the labeled area on the window. Follow the instructions printed on the protective backing of the Gecko Tape to ensure the bracket is securely affixed. Note: When attaching the mounting bracket, make sure it is oriented in the manner shown in the image below (with the opening of the mounting slot facing up). Note 2: Do not attach the mounting bracket onto slanted windows. 7 3. Once the bracket is securely affixed to the window, align the mounting head on the Extender with the installation slot on the bracket, then push down on the Extender to insert the mounting head into the slot. Adjust the alignment of the Extender as required (make sure the raised nubs on the mounting head fit into the dimple holes on the inside of the slot, and that the hole for the DC jack is aligned with the hole for the AC adapter on the bottom of the slot). 4. Once the desired alignment is achieved, use a screwdriver to screw the securing screw through the designated hole on the bottom of the installation slot and into one of the screw holes on the mounting head of the Extender. Make sure the screw is screwed in tightly and is not loose. 5. Use the provided cable clips for cable management. You may also install the provided window wedges to prevent sliding windows from colliding with the installed Extender. 6. To remove the mounting bracket from window glass, first unplug the AC adapter from the DC jack. Afterwards, use a prying tool or other suitable flat object (such as a flathead screwdriver) and use it to pry the mounting bracket off the window by carefully wedging it between the window glass and the Gecko Tape. 8 2.2 Wall Mounting Note: The Extender can only be mounted on drywall or wooden walls. 1. Find a location on the wall near where the installation location label is placed. Peel off the protective backing on the Gecko Tape on the back of the mounting bracket, and remove the cover on top of the bracket base. Afterwards, place the mounting bracket against the wall at the aforementioned location using the same alignment used for window installation. 2. Use a pencil to mark the points on the wall directly under the center of the two mounting holes of the mounting bracket. 3. For installation on drywall, after completing the steps in item 2, move the bracket off the wall. Use a power tool to drill pilot holes at the marked points (Note: the diameter of the pilot holes must be smaller than the diameter of the included wall anchors), then push the anchors into the pilot holes until they are flush to the wall. Afterwards, align the center of the two mounting holes of the mounting bracket with the anchors, then use a screwdriver to slowly screw the included metal wall screws into the anchors until the bracket is securely fastened. 9 4. For installation on wooden walls, after completing the steps in item 2, use a power tool and slowly screw the included metal screws into the marked points until the bracket is securely fastened. Note: Do not install the mounting bracket onto slanted walls. 5. Once the bracket is securely fastened to the wall, align the mounting head on the Extender with the installation slot on the bracket, then push down on the Extender to insert the mounting head into the slot. Adjust the alignment of the Extender as required (make sure the raised nubs on the mounting head fit into the dimple holes on the inside of the slot, and that the hole for the DC jack is aligned with the hole for the AC adapter on the bottom of the slot). 10 6. Once the desired alignment is achieved, use a screwdriver to screw the securing screw through the designated hole on the bottom of the installation slot and into one of the screw holes on the mounting head of the Extender. Make sure the screw is screwed in tightly and is not loose. 7. Use the provided cable clips to conduct cable management. 11 Chapter 3 Product Specifications Hardware Specification Support Frequency Band: n261 (27.528.35 GHz) Separated TX & RX antenna arrays Antenna array

- 32 elements at donor side

- 2 antenna panels at relay side, each has 4 elements Peak EIRP at P1dB

- Donor 46 dBmi

- Relay 28 dBmi Micro-controller and Memory DC Jack for 12 V/4 A power adapter Operating Temperature: 5C to 40 C Dimension: 181.5 mm 181.5 mm 49 mm

- SPI NOR Flash BLE 4.2 One RGBW LED Buzzer 1 Weight: 1.2 kg Environmental Operating Ambient Temperature: 5 C to 40 C Operation Relative Humidity: 5% to 90% non-condensing Storage Temperature: 45C to 70C Shipping and Storage Relative Humidity: 5% to 85%

12

WNC CONFIDENTIAL A NEW RELEASE 03/27/20 SAM SUN FCC ID: NKR-TR1V1-IDU WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. FCC ID: NKR-TR1V1-IDU WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. NOTES:

1. MATERIAL: PET, t=0.075 ADHESIVE:

FINISH: PET, T=0.025 2. COLOR: LV11 PRIMARY GARY,PMS COOL GREY 5C 3. 4. 30.5MM,3.00.3MM 5. :ABS 6. :30mm0.3mm,120~315mm0.5mm,3150.8mm 7. TEST REQUIREMENT 3

. 5 0 3

. 1 29.6 1.30.5 7

. 2 2 FCC ID: NKR-TR1V1-IDU WARNING. This is NOT a CONSUMER device. It is designed for installation by FCC LICENSEES and QUALIFIED INSTALLERS. You MUST have an FCC LICENSE or express consent of an FCC Licensee to operate this device. Unauthorized use may result in significant forfeiture penalties, including penalties in excess of $100,000 for each continuing violation. DIE LINE (DO NOT PRINT) PMS COOL GREY 5C LV11 PRIMARY GARY() 2 AMANDA LAI AMANDA LAI SAM SUN 03/27/20 03/27/20 03/27/20 LABEL, FCC WARNING, UPDATED, TR1 4L.TR100.00401 A 1/1 1 OF 1 1 ISO Class.: 1 ASTM Class.: 4 B ASTM D3359-02/ ISO

*1

*2 4

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park Hsinchu 308. Tatwan Date: 2020-03-16 FCC ID: NKR-TRIV1-IDU AUTHORIZATION LETTER To Whom It May Concern:

Wistron NeWeb Corporation hereby authorizes Joanna Hung / Specialist of Bureau Veritas Consumer Products Services (H. K.) Ltd., Taoyuan Branch (BV CPS Taoyuan), to act on its

- + 7f~Ce peer cnet se eye NE ee Dealt mM ali Matters relating to the rederal Communication Commission (KCC) application tor equipment authorization in connection with the FCC ID listed above, including signing of all documents relating to these matters. Any and all acts carried out by Joanna Hung / Specialist of BV CPS Taoyuan on Wistron NeWeb Corporations behalf, within the scope of the powers granted herein, shall have the same effect as acts of its own. If you have any questions regarding the authorization, please dont hesitate to contact us. Sincerely yours, Brown Wang / Director / Project Management Dept. |

Wistron NeWeb Corporation _ Tel: 886-3-666-7799 ext 6127 Gawe COL FOE L20 fN7eo A he VOY LY YU Y VIO E-mail: brown.wang@wnc.com.tw Shratan cere

Wistron NeWeb Corporation 20 Park Avenue Il, Hsinchu Science Park Hsinchu 308, Taiwan PROFESSIONAL INSTALLATION ATTESTATION Date: 2020-04-10 FCC ID: NKR-TRIV-IU To whom it may concem, We, Wistron NeWeb Corporation declare that this booster, FCC ID: NKR-TR1V1-IDU, is. designed specifically for enhancing the 5G NR signal strength for our subscriber who is experiencing poor signal reception and is not for sale to the generat public. Since installation fs case by case determined and it requires knowledge of our network handshake protocol between each network component and where the best location /orientation for installing the booster is, ALL installations therefore must be done by a professional installer. We hereby declare that this device will be installed by a professional installer only and will not be sold to the general public. Thank you and please contact us if you should have any question(s). Sincerely yours, Wistron NeWeb Corporation Tek: 886-3-666-7799 ext 3155 Fax: 886-3-563-0789 E-mail: Angela.Lin@wne.com.tw

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park Hsinchu 308, Taiwan Declaration letter Date: 2020-03-27 FCC ID: NKR-TR1IV1-IDU To Whom It May Concern:

We, Wistron NeWeb Corporation, declare that the product Verizon 5G Extender, will have t warning label messages shown in online and point-of-sale marketing materials and on the out side pe the device. If you have any questions regarding this authorization, please do not hesitate to contac you!

LICE ENSEES and Qt QUALIFIED NSTALLERS. You MUST have an FCC uc! Eh IS Eo consent of an FCC Licensee to opere e this ere inate ni significant forfeiture pen f af t continuing violation. : an Thank you for your attention. Sincerely yours,

Wistron NeWeb Corporation 20 Park Avenue II, Hsinchu Science Park Heinchu 308, Taiwan Date: 2020-04-10 FCC ID: NKR-TRIVL-IDU To the attention of Federal Communications Commission Authorization and Evaluation Division Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the commissions rules, we request short-term confidential treatment for the following information until (year/month/day) or (90days after the Grant Date of Equipment Authorization) in onder to ensure sensitive business information remains confidential until, the actual marketing of the device:

External photos Test Setup photos Users manual Internal Photos Sincerely yours, Angela Lin / Project Manager / Project Management Dept. Wistron NeWeb Corporation Tel: 886-3-666-7799 ext 3155 Fax: 886-3-666-7323, mail: Angela in@wne.com.tw Pursuant to Sections 0.457 and 0.459 of the commission's rules, we request short-term confidential treatment for the following information until 90 days after the Grant Date of Equipment Authorization in order to ensure sensitive business information remains confidential until the actual marketing of the device:

Wistron NeWeb Corporation 20 Park Avenue Il, Hsinchu Science Park. Hsinchu 308, Taiwan Date: 2020-04-10 FCC ID: NKR-TRIVL-IDU To the attention of Federal Communications Commission Authorization and Evaluation Di Permanent Confidentiality Request Pursuant to Sections 0.457 and 0.459 of the Commission's Rules, the Applicant hereby requests confidential treatment of information accompanying this Application as outlined below:

Schematies Block Diagram Operational Description Tune up Procedure The above materials contain trade secrets and proprictary information not customarily released to the public, The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. The Applicant understands that pursuant to Rule 0.457, disclosure ofthis Application and all accompanying documentation will not be made before the date of the Grant for this appl Sincerely yours, __frigele Law Angela Lin Project Manager / Piet Management Dept Wiston NeWeb Coporaion Tel: 886-3-666-7799 ext 3155 Fax: 886-3-666-7323 E-mail: Angela.Lin@wne.com.tw

WNC Wistron NeWeb Corp. AGENCY AUTHORIZATION LETTER Date: 2020-4-9

|, William Su, am senior compliance manager for Wistron NeWeb Corp. hereby authorize the following to act on our behalf, as our agent, in all matters relating to all processes required according to FCC/IC Approval for Wistron NeWeb Corp. products. Angela Lin Brown Wang This Letter of Authorization will expire on 12/31/2020, unless earlier revoked in writing. If you have any questions regarding the authorization, please don t hesitate to contact us. Sincerely, Sincerely, William Su / Senior Compliance Manager Wistron NeWeb Corp. Tel: 886-3-6667799 Ext 6688 E-mail: William.Su@wnc.com.tw