AudioMagic AVMD6210-SWA12 Preliminary Module Brief Point-to-point AVMD6210-SWA12TX/RX modules for Stereo and Mono Wireless Audio Systems, based on Avneras AV6210 IC Features
Audio Interfaces
I2S Digital Input Interface with 93dB end-to-end digital audio path
Support for >15m range
Frequency range: 2.4 GHz ISM band, continuous dynamic frequency selection
Forward error correction coding, error detection, and audio-specific error concealment
Custom Dual onboard printed PCB antennas for multipath and fading mitigation
Auto-search/synch and dynamic channel selection
Low, fixed latency of 16ms, suitable for video lip-synch
Connector: 24 position 0.5mm flex cable connector for maximum mounting flexibility in the system.
Sample rate converter: Support for 16, 20, 24, and 32 bit PCM words at 8,16, 22.05, 24, 32, 44.1, and 48 kHz
General purpose over-the-air (OTA) serial interface:
2 kbps, bi-directional, full duplex
Support for meta-data and remote control commands General Description Every consumer wants to be free from wires, but it has been challenging to find a low-cost, high-quality, easy-to-use wireless audio solution for the wireless subwoofer market. Avneras proprietary wireless system takes a new approach to wireless audio. The wireless protocol was designed from the ground up and delivers uncompressed mono or stereo audio, with fixed latency and variable over the air data rate support to eliminate interference problems at the best possible audio quality. Avneras wireless modules offer a low-touch, easy-to-integrate wireless audio solution and enable fast time to market by already solving the problem associated with FCC certification, antenna tuning and board optimization. Modules based on Avneras AV6200 silicon provide audio functionality with fixed low-latency point-to-
point transport of uncompressed mono PCM audio data at up to 48KHz, 16-bit resolution using digital (I2S) interfaces. breakthrough wireless Applications
Wireless Subwoofers
Stereo audio channel transmission Ordering Options AVMD6200-SWA12 TXD: Transmit module with digital audio input and integrated printed PCB antennas AVMD6200-SWA12 RXD: Receive module with digital audio output and integrated printed PCB antennas AVNERA CORPORATION | 16505 NW BETHANY COURT SUITE 100 | BEAVERTON, OREGON 97006, U.S.A. | MAIN +1.503.718.4100 | FAX +1.503.718.4101 | WWW.AVNERA.COM AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AudioMagic AVMD6210-SWA12 Module Brief PRELIMINARY v0p1 4 AVMD6210-SWA12- Connector Information Table 1 shows the module connector pin out for the SWA12. A goal of the design is to have the exact same pin out for both the Tx and Rx modules. The module function is completely determined by firmware. The module pins provide the capability to use either SPI slave or I2C slave interfaces these are mutually exclusive. If an I2C slave host interface is used GPIOs 2 and 3 can be used for general purpose I/O. In addition, the SPI master port is brought out to the connector to facilitate direct programming of the module flash memory if required. A single I2S port is brought to the connector and can be configured to be either a slave or master port. The MCLK pin can be an input or output to offer optimal flexibility. Likewise the I2S audio pin can be an input or output to implement either audio Tx or Rx. In addition, there are 5 other GPIOs that can be used exclusively for system features such as pair button, interrupt, LEDs etc. The reset pin allows for an external device to reset the module but must be driven from an open drain device to avoid timing issues with the module reset. Note: the connector pin out is subject to change throughout the development process to optimize the PCB routing. SWA12 Pin-Out Pin Name VDD VDD GPIO GPIO GPIO Reset I2C_SCL_S / S_MISO I2C_SDA_S / S_MOSI I2C_SCL_M I2C_SDA_M S_SCLK No 1 2 3 4 5 6 7 8 9 10 11 12 GND 13 BCK1 14 WCLK1 15 S_SSB 16 MCLK 17 18 M_SSB 19 M_SCLK 20 M_MOSI 21 M_MISO 22 GPIO 23 GPIO 24 GND ADOUT/ADIN1 AV6200 Pin 24 I/O
-
-
I/O GPIO13 pin 28 I/O GPIO18 pin 43 I/O GPIO19 pin 37 I I/O GPIO5 pin 44 I/O GPIO4 pin 45 O GPIO22 pin 41 I/O GPIO21 pin 42 GPIO3 pin 46 I
-
I/O GPIO15 pin 26 I/O GPIO16 pin 25 I GPIO2 pin 47 I/O GPIO10 pin 31 I/O GPIO14 pin 27 GPIO6 pin 36 O GPIO7 pin 35 O O GPIO8 pin 34 I GPIO9 pin 33 I/O GPIO11 pin 30 I/O GPIO12 pin 29
-
Pin Description
+5V +/- 10%
+5V +/- 10%
Function defined by firmware application. Function defined by firmware application. Function defined by firmware application. Driven from open drain external source. Can be left open. I2C slave or SPI slave port I2C slave or SPI slave port I2C master port or GPIO I2C master port or GPIO SPI slave port or GPIO Ground I2S port I2S port SPI slave port or GPIO I2S port or GPIO I2S port SPI master port SPI master port SPI master port SPI master port Function defined by firmware application. Function defined by firmware application. Ground Table 1 Rx and Tx SWA12 Module Pin-Out CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 5 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6210-SWA12 Module Brief PRELIMINARY v0p1 5 AVMD6210-SWA12 Mechanical Dimensions 26mm 1mm x 3mm location slots 3 places 60mm 2 5 m m Shield Can Approx 23 x 25mm 3 3 m m 23mm Pin 1 Connector Mounting tabs around perimeter of PCB tbd Mounting Hole Figure 3 - AVMD6210-SWA12 mechanical dimensions CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 7 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6210-SWA12 Module Brief PRELIMINARY v0p1 6 Electrical Specifications 6.1 Absolute Maximum Ratings Absolute Maximum Ratings (AMR) are stress ratings only. AMR corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Stresses beyond those listed under AMR may cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Range is not implied. Exposure to absolute-maximum-rated conditions for extended periods may adversely affect device reliability. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. CONDITION MIN VDD Supply Voltage Input Input Voltage Range Digital Inputs1 Operating Temperature Storage Temperature Assembly Temperature Static Discharge Voltage HBM2 Static Discharge Voltage MM3
-0.3V
-0.3V
-20C
-40C TBD TBD MAX 6.0V 3.6V
+80C
+100C TBD Notes:
Note 1: Digital GPIO Pins are 5V Tolerant when programmed as Inputs. Note 2: Terminology: HBM => ESD human body model Note 3: Terminology: MM => Machine model 6.2 Recommended Operating Range PARAMETER MIN VDD Supply pin voltage Ambient Temperature (TA) 4.5 0 TYP MAX 5.5 70 UNIT V C CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 8 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6210-SWA12 Module Brief PRELIMINARY v0p1 6.3 Electrical Characteristics Test Conditions: TA=+25C, VDC=+5.0V Table 2 - AVMD6210-SWA12 Electrical Characteristics NDITIONS PARAMETER CO RF Frequency Range RF Transmit power RF Receiver sensitivity1 Range (LOS) Audio SNR I2S Input/Output2 Audio SNR I2S Input/Output2 Analog Audio THD+N3 Audio Bandwidth (end to end I2S) Audio Bandwidth (end to end I2S) Current consumption I2S end to end 16bit mode I2S end to end 12bit mode 0.1dB point 20KHz mode 0.1 dB point 5KHz mode VDC(Active Audio mode) MIN 2402
-3
-86 90 70 TYP MAX 2478 0
-89
>15 93 72 tbd 20 5 50 UNIT MHz dBm dBm m dB dB dB KHz KHz mA Note 1: AV6200 IC specification, measure by conducted u.fl connection at IC Note 2: AVMD6200-SWA12-TX/RX Note 3: Measured at -3dbFS input, A weighting. Output is taken, using external DAC on Avnera development board. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 9 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6210-SWA12 Module Brief PRELIMINARY v0p1 7 Firmware Architecture 7.1 Standard Firmware Options Avnera provides standard firmware images that implement basic wireless link operation. Each of these images uses 1 GPIO as a link status indicator and another GPIO is an input used to get the module into pairing mode as illustrated in Figure 4. Figure 4 Standard Module Firmware Topology The basic firmware image options supported are:
Tx Module SWA12TX-44/16-Slave SWA12TX-44/16-Master SWA12TX-11/16-Slave SWA12TX-11/16-Master Rx Module SWA12RX-44/16-Slave SWA12RX-44/16-Master SWA12RX-11/16-Slave SWA12RX-11/16-Master Over-the-Air Audio Format 44KSps @ 16bit Stereo 44KSps @ 16bit Stereo 11KSps @ 16bit Mono 11KSps @ 16bit Mono Over-the-Air Audio Format 44KSps @ 16bit Stereo 44KSps @ 16bit Stereo 11KSps @ 16bit Mono 11KSps @ 16bit Mono I2S Configuration I2S Slave I2S Master I2S Slave I2S Master I2S Slave I2S Master I2S Slave I2S Master I2S Configuration Table 3 Standard Firmware Image Support 7.2 Custom Firmware Options Beyond the basic audio, link status and pairing functionality, it is possible for Avnera to customize the firmware functionality to support advanced system features such as over-the-air communication by means of either an I2C or SPI host interface. Customization may consist of features such as:
Defined command and control API through I2C/SPI host interface Data transfer between the Tx and Rx modules Custom apps running on the module MCU to implement I2C master port or specific GPIO input/output functions CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 10 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6210-SWA12 Module Brief PRELIMINARY v0p1 7.3 Firm ware Upgrades The possible interfaces that can be used for upgrades of the flash memory device are shown in Figure 5. With the standard firmware implementation, firmware upgrades are achieved by using the module SPI master port to directly program the module flash device. Avnera provides a GUI application that runs on a PC to facilitate direct SPI programming. By means of additional custom firmware, programming of the module flash device can be achieved via the slave I2C or SPI host interfaces. It is also possible to implement over-the-air programming of the Rx module so all elements of a system can be upgraded through a single host interface. This requires working with customer to define the functionality and architecture required as well as the customer host interface and API to the Tx module. Over the Air Interface for Rx Module SWA12 Module SPI Master Interface Avnera AV6210 Wireless Transceiver Flash Memory Device I2C Host SPI Host I/F I/F Custom Host Interfaces Direct Flash Progamming Figure 5 Flash Programming Interface Options 8 Application 8.1 Applica tion circuit information Application schematics are available from Avnera Support. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 11 AVNERA PROPRIETARY & CONFIDENTIAL FCC Statement:
Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID:
NKR-SWA12 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. IC Statement:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC :
4441A-SWA12 ".