WirelessAudioModule AVMD7520SWA3 ChrisO'Connor 2010/12/29 Customer P/N: N/A Avnera Model: AVMD7520-SWA3 WNC P/N: 55SWA301.SG1 Description: Wireless Audio Module AVMD7520-SWA3
+15dBm, integrated antenna, 4 channel digital I/O Wireless HD Audio Module Solution radio module General Description is a The AVMD7520-SWA3 module complete solution containing all the necessary HW and FW to provide a system-integration-
ready, multichannel wireless HD audio solution compatible with the AM2G and AAL wireless audio system. The module is comprised of an AV7520 IC combined with RF front-end circuits
(RF PA + balun + filter + RF switch), FLASH memory, crystal, and passive components. is an FCC-certified modular solution with high performance PCB printed antennas. The module also provides a convenient set of digital I/O interfaces for digital audio through an I2S port, host MCU control through an SPI or I2C interface and optional GPIO for indicator functions. The module is a card slot style using the 36 pin PCIe card edge pin arrangement to save space and cost in connecting to a main system board. control and various It Features
Complete, Integrated Wireless Module o AV7520 IC o Complete RF front-end o Single +5V supply voltage connection
High Performance Audio and RF solution o Supports 16 bit, 48kHz up to 24 bit, 96kHz digital audio formats o 120dB SNR Audio Path o Fixed Low Latency solution o +15dBm transmit RF output power o o Support for 30m/150m range NLOS/LOS
-82dBm receive RF sensitivity
Digital interfaces and Audio o 4 channel digital audio I/O (2 stereo I2S ports)
Configurable as input or output o Stereo audio DAC output o 4-wire SPI slave interface or 2-wire I2C-compatible communication with the host MCU
Package and connections o Compact size (38mm x 53mm) o 36 pin (2x18) PCIe style card slot edge connector o Dual PCB printed antennas for diversity support CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 2 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 Revision History Revision Change Summary 1.0 Initial release Release Date Nov, 2010 Table of Contents 3 2.7 2.8 2.6.1 2.6.2 2.1 2.2 2.3 2.4 2.5 2.6 General Description .............................................................................................................................................................. 2 Features ............................................................................................................................................................................... 2 List of Figures ....................................................................................................................................................................... 3 AVMD7520-SWA3 PIN CONFIGURATION................................................................................................................. 4 1 2 ELECTRICAL SPECIFICATIONS ............................................................................................................................... 6 Absolute Maximum Ratings ............................................................................................................................... 6 DC Electrical Characteristics ............................................................................................................................. 6 Electrical Characteristics RF Receiver ............................................................................................................ 7 Electrical Characteristics RF Transmitter ........................................................................................................ 7 Electrical Characteristics RF Channel Frequency .......................................................................................... 8 Electrical Characteristics End-to-end Audio Characteristics ........................................................................... 8 I2S Paths ...................................................................................................................................................... 8 Audio DAC Path ............................................................................................................................................ 8 Electrical Characteristics MCLK Characteristics ............................................................................................. 9 Over-the-air Range ............................................................................................................................................ 9 Package Information ................................................................................................................................................. 10 Mechanical Dimensions ................................................................................................................................... 10 Ordering Information ................................................................................................................................................. 11 4 5 CONTACT INFO & LEGAL DISCLAIMER................................................................................................................. 12 FCC Statement ................................................................................................................................................................... 14 For product available in the USA/Canada market, only channel 1~11 can be operated. Selection of other channels is not possible. .............................................................................................................................................. !
IC Statement: ...................................................................................................................................................................... 16 List of Figures Figure 1-1 AVMD7520-SWA3 module pin configuration .................................................................................................... 4 Figure 3-1 - AVMD7520-SWA3 module mechanical dimensions ........................................................................................ 10 3.1 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 3 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 1 AVMD7520-SWA3 PIN CONFIGURATION B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 A18 A17 A16 A15 A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 B-side
(with shield can) A-side
(No shield can) Connector Top View VCCPA VCC5V ADAT3 BCLK3 WCLK3 MCLK_OUT ADAT1 BCLK1 WCLK1 SDA SCL S_SSB S_SCLK S_MOSI S_MISO SRQ/PND SM0 WM_DETN/GND B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 B14 B15 B16 B17 B18 GND GND GPIO2 GPIO23 GPIO22 GPIO18 GPIO17 GPIO16 GPIO7 GPIO6 GPIO4 GPIO3 GPIO5 GND AGND ROUT LOUT AGND A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 AVMD7520-SWA3 Pinout Configuration v.1 Figure 1-1 AVMD7520-SWA3 module pin configuration CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 4 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 Table 1-1 AVMD7520-SWA3 Pin Description Pin Name
A1 GND A2 GND A3 GPIO2 A4 GPIO23 A5 GPIO22 A6 GPIO18 A7 GPIO17 A8 GPIO16 A9 GPIO7 A10 GPIO6 A11 GPIO4 A12 GPIO3 A13 GPIO5 A14 GND A15 AGND A16 ROUT A17 LOUT A18 AGND VCCPA B1 VCC5V B2 ADAT3 B3 B4 BCLK3 B5 WCLK3 B6 MCLK_OUT ADAT1 B7 B8 BCLK1 B9 WCLK1 B10 SDA B11 SCL B12 S_SSB B13 S_SCLK B14 S_MOSI B15 S_MISO B16 SRQ/PND B17 SM0 Pin Type Analog Analog Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Ground Analog Analog Analog Analog Analog Analog Digital I/O Digital I/O Digital I/O Digital Output Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital I/O Digital Output Digital Input B18 WM_DETN / GND Digital output Description Module ground Module ground GPIO #2 See Note GPIO #23 GPIO #22 GPIO #18 GPIO #17 GPIO #16 GPIO #7 GPIO #6 GPIO #4 GPIO #3 GPIO #5 Module ground See Note Audio DAC ground; do not connect to module or system board ground Audio DAC right channel output Audio DAC left channel output Audio DAC ground; do not connect to module or system board ground
+5V supply voltage input for the RF power amplifier
+5V supply voltage input for the module I2S Audio Data for AV75xx I2S I/O Port # 3 I2S Bit Clock for AV75xx I2S I/O Port # 3 I2S Word Clock for AV75xx I2S I/O Port # 3 MCLK for I2S audio data I2S Audio Data for AV75xx I2S I/O Port # 1 I2S Bit Clock for AV75xx I2S I/O Port # 1 I2S Word Clock for AV75xx I2S I/O Port # 1 I2C compatible serial data I/O I2C compatible serial clock I/O SPI Slave Slave Select (active low) SPI Slave Serial Clock SPI Slave Master Out / Slave In SPI Slave Master In / Slave Out Notification signal to host (pending notification) Serial MUX control (for flash programming) and module reset (active low) Wireless module detect (low signal to indicate module is inserted in product) (This pin is internally connected to Module ground pins A1, A2, & A14) Note: The GPIO2 module pin assignment is different from that uses on the AVMD7520-SWA1 and AVMD7540-SWA4 modules, which assign GPIO2 to Pin A14 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 5 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 2 ELECTRICAL SPECIFICATIONS 2.1 Absolute Maximum Ratings The Absolute Maximum Rating (AMR) corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics and for the test conditions specified. Table 2-1 AVMD7520-SWA3 Absolute Maximum Ratings CONDITION Supply (relative to GND)
+5V supply voltage range Input Voltage Range Digital Inputs Short circuit to GND (any pin) Storage Temperature ESD Voltage Rating Human Body Model test MIN
-0.3
-0.3
-20 MAX 6.0 3.6V continuous
+85 2000 Units V V C V 2.2 DC Electrical Characteristics Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA3 edge connector pins and RF connectors, unless otherwise specified. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-2 AVMD7520-SWA3 DC Electrical Characteristics PARAMETER Input supply voltage Supply Current +5V supply (Note 1) CMOS I/O Logic Levels 3.3V I/O Input Voltage Logic Low, VIL Input Voltage Logic High, VIH Output Voltage Logic Low, VOL Output Voltage Logic High, VOH CONDITIONS Driven by an external regulator RESET OTA RX mode, 2 output channels via I2S OTA TX mode, 2 input channels via I2S FCC_TX (Pout = +15dBm) RX_search VVDC33 = 3.3V VVDC33 = 3.3V VVDC33 = 3.3V; ILOAD=1mA VVDC33 = 3.3V; ILOAD=1mA MIN 4.5 2.0 2.9 TYP 6 126 160 425 220 MAX 5.5 0.6 0.4 UNIT V mA mA mA mA mA V V V V Note 1: The operating states are defined as follows:
RESET: The AVMD7520-SWA2 is held in RESET by holding the SM0 input LOW OTA-RX mode: The AVMD7520-SWA2 is operating in an Over-The-Air (OTA) link as a Client node, receiving 2 channels of 16bit, 48 kHz audio OTA-TX mode: The AVMD7520-SWA2 is operating in an OTA link as an Arbiter node, transmitting 2 channels of 16bit 48 kHz audio FCC_TX mode: The AVMD7520-SWA2 is operating in the diagnostic FCC_TX mode RX_search mode: The AVMD7520-SWA2 is configured as a Client and is powered ON but not operating in a link (in which case it will be in continuous RX search mode) CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 6 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 2.3 Electrical Characteristics RF Receiver Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA3 edge connector pins and RF connectors, unless otherwise specified. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-3 AVMD7520-SWA3 Electrical Characteristics RF Receiver PARAMETER RF Channel Frequency Range Sensitivity (Note 1) Max Input Signal (Note 1) Spurious RF outputs LO leakage CONDITIONS TA=25C 2400-2483.5 MHz
<2400 MHz
>2483.5 MHz MIN 2412 TYP
-82
-5 MAX 2462
-47
-60
-60
-47 UNIT MHz dBm dBm dBm dBm dBm dBm Note 1: Sensitivity and max signal level are defined as the onset of 1% BLER Block Error Rate. 2.4 Electrical Characteristics RF Transmitter Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA3 edge connector pins and RF connectors, unless otherwise specified. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-4 AVMD7520-SWA3 Electrical Characteristics RF Transmitter PARAMETER RF Channel Frequency Range Output Power (Note 1) Harmonics (Note2) Conducted RF Spurious signals (Note2) Radiated Spurious RF signals (Note 3) CONDITIONS TA=25C, OFDM signal, 16MHz channel BW 2nd harmonic 3rd harmonic
< 2390MHz; RBW=1MHz
> 2483.5MHz; RBW=1MHz 30-88MHz, 88-216MHz 216-960MHz
>960MHz MIN 2412 TYP
+15 34 37 40 48 MAX 2462
-50
-55
-45
-45 UNIT MHz dBm dBm dBm dBm dBm dBuV/m dBuV/m dBuV/m dBuV/m Note 1: Output power is the average transmitter output power in a 16MHz bandwidth centered on the channel, measured at the U.FL connector with the port terminated into a load of 50 ohms at the frequency of interest. The stated specification refers to the maximum level measured at either antenna port. Note 2: Harmonic and Conducted RF Spurious Signal power are measured at the U.FL connector, with the port terminated into a load of 50 ohms at the frequency of interest. The stated specification refers to the maximum level measured at either antenna port. Note 3: Radiated Spurious RF Signal strength is the radiated power measured in a calibrated chamber, with the module antenna ports connected to dipole antennas having +2dBi (nominal) gain. The stated specification refers to the level measured from either antenna port. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 7 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 2.5 Electrical Characteristics RF Channel Frequency Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = see below. All specifications are referenced to the AVMD7520-SWA3 edge connector pins and RF connectors, unless otherwise specified. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-5 AVMD7520-SWA3 Electrical Characteristics RF Channel Frequencies PARAMETER Channel Frequency Frequency Error CONDITIONS AM2G system channel 1 AM2G system channel 2 AM2G system channel 3 16MHz crystal MIN TYP 2412 2438 2462 MAX
+/- 20 UNIT MHz MHz MHz ppm 2.6 Electrical Characteristics End-to-end Audio Characteristics I2S Paths 2.6.1 Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA3 edge connector pins and RF connectors, unless otherwise specified. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-6 AVMD7520-SWA3 Electrical Characteristics End-to-end Audio Characteristics PARAMETER End-to-end SNR Latency Bandwidth CONDITIONS I2S in to I2S out, no interference;
16bit / 48kHz mode 24bit / 48kHz mode 16bit / 96kHz mode 24bit / 96kHz mode 48kHz, interleaving level = 0 48kHz, interleaving level = 1 48kHz, interleaving level = 2 96kHz, interleaving level = 0 96kHz, interleaving level = 1 96kHz, interleaving level = 2
+/-0.5dB flatness, 48Khz modes
+/-0.5dB flatness, 96Khz modes MIN 96 120 97 120 20 20 TYP MAX UNITS 11 15 19 9.5 13.5 17.5 20k 40k dB dB dB dB ms ms ms ms ms ms Hz Hz 2.6.2 Audio DAC Path Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA2 edge connector pins and RF connectors, unless otherwise specified. Measurements use a 24bit, 96kHz digital I2S audio input on the sending side. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-7 AVMD7520-SWA2 Electrical Characteristics Analog Audio (DAC) Characteristics PARAMETER THD+N Dynamic range Channel isolation Load resistance Load capacitance CONDITIONS 0 dBFS fs = 48 kHz (-60 dBFS, A-weighted) fs = 48 kHz (-60 dBFS, BW = 20Hz 20kHz) fs = 96 kHz (-60 dBFS, BW = 20Hz 40kHz) MIN 5 TYP
-88 99 99 99 100 10 MAX 25 UNITS dB dB dB dB dB k pF CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 8 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 Common-mode output voltage Full-scale output voltage swing 1.40 1.70 V Vp-p Note: Audio DAC path characteristics reflect the capabilities of the on-chip DAC and module; however, care must be taken in the layout and wiring of the external audio path to prevent degradation of the signal environment. 2.7 Electrical Characteristics MCLK Characteristics Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA2 edge connector pins and RF connectors, unless otherwise specified. Measurements use a 24bit, 96kHz digital I2S audio input on the sending side. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-8 AVMD7520-SWA3 Electrical Characteristics MCLK Characteristics PARAMETER MCLK frequency MCLK output duty cycle CONDITIONS 24MHz mode (256MHz divide by 10.5) 12MHz mode (256MHz divide by 21) MIN 40 TYP 24.38 12.19 MAX 60 UNITS MHz MHz
2.8 Over-the-air Range Operating Conditions: VCC = 5.0V 10%, TA=0C to +50 C; RF Chan. Freq = 2412MHz to 2462MHz. All specifications are referenced to the AVMD7520-SWA3 edge connector pins and RF connectors, unless otherwise specified. Typical specifications use VCC = 5.0V and TA=25 C. Table 2-9 AVMD7520-SWA3 Electrical Characteristics Range PARAMETER LOS (line-of-sight) Range (Note 1) NLOS (non-line-of-sight) Range (Note 1) CONDITIONS 2 channel audio link; >=100cm height 2 channel audio link; >=100cm height MIN TYP 150 30 MAX UNIT m m Note 1: Range is defined as the maximum distance at which there are no audio breaks. The LOS environment is outdoors, with no obstructions between the arbiter and client AV75xx radios. NLOS is indoors, with obstructions (typically walls) between the arbiter and client AV75xx radios. NLOS range performance will be highly dependent on the actual environment. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 9 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 3 Package Information 3.1 Mechanical Dimensions 45.60 mm 45.60 mm 8.85 mm 8.85 mm 57.50 mm 57.50 mm 8.50 mm 8.50 mm 11.90 mm 11.90 mm 20.05 mm 20.05 mm 21.95 mm 21.95 mm 29.15 mm 29.15 mm 38.00 mm 38.00 mm Figure 3-1 - AVMD7520-SWA3 module mechanical dimensions 3.0 mm 3.0 mm 4.6 mm 4.6 mm 1.60 mm 1.60 mm CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 10 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 4 Ordering Information Table 4-1 AVMD7520-SWA3 Module Ordering Information Module Part Number AVMD7520-SWA3 Description
+15dBm TX power, printed antenna, AV7520 based wireless audio module CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 11 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 5 CONTACT INFO & LEGAL DISCLAIMER Avnera Corporation 16505 Bethany Court, Suite 100 Beaverton, Oregon 97006 U.S.A. Main: +1.503.718.4100 Fax: +1.503.718.4101 www.avnera.com Avnera Corporation reserves the right to make changes without notice to the product to improve function, reliability, or performance. Avnera Corporation does not assume any liability arising from the application or use of the products or circuits described herein. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 12 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 13 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 FCC Statement Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 14 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the FCC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the FCC radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: NKR-SWA3". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 15 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AVMD7520-SWA3 Module Datasheet Preliminary revision 1.0 IC Statement:
This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
IC Radiation Exposure Statement:
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. 20cm minimum distance has to be able to be maintained between the antenna and the users for the host this module is integrated into. Under such configuration, the IC RSS-102 radiation exposure limits set forth for an population/uncontrolled environment can be satisfied. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed to keep at least 20cm separation with the antenna while this end product is installed and operated. The end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC : 4441A-SWA3 ". CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 16 AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA