PRELIMINARY AudioMagic Module Datasheet Point-to-point AVMD6600-SWA91 module family for Mono Wireless Audio Systems, based on Avneras AV6600 IC Features Audio Interfaces I2S Digital Input Interface with 95dB end-to-end digital audio path Integrated DAC supporting Analog output with 90dB SNR and 20-20KHz bandwidth (RXA model only) Support for 15m range Frequency range: 2.4 GHz ISM band, continuous dynamic frequency selection Forward error correction coding, error detection, and audio-specific error concealment Dual onboard printed PCB antennas for multipath and fading mitigation Auto-search/synch and dynamic channel selection Low, fixed latency of 13ms, suitable for video lip-synch Connector: 2mm header which allows for either horizontal or vertical module mounting Sample rate converter: Support for 16, 20, 24, and 32 bit PCM words at 8,16, 22.05, 24, 32, 44.1, and 48 kHz General purpose over-the-air (OTA) serial interface:
2 kbps, bi-directional, full duplex Support for meta-data and remote control commands the air, without General Description Every consumer wants to be free from wires, but it has been challenging to find a low-cost, high-quality, easy-to-use wireless audio solution for the wireless subwoofer market. Avneras proprietary wireless system takes a new approach to wireless audio. The wireless protocol was designed from the ground up and delivers uncompressed mono audio, with fixed latency over interference problems. Avneras wireless modules offer a low-touch, easy-to-integrate wireless audio solution and enable fast time to market by already solving the problem associated with FCC certification, antenna tuning and board optimization. Modules based on Avneras AV6600 silicon provide audio functionality with fixed low-latency point-to-
point transport of uncompressed mono PCM audio data at 16-bit, 48 kHz resolution using either analog or digital (I2S) interfaces. breakthrough wireless Applications Wireless Subwoofers Mono audio channel transmission Ordering Options AVMD6600-SWA91TXD: Transmit module with digital audio input and integrated printed PCB antennas AVMD6600-SWA91RXD: Receive module with digital audio output and integrated printed PCB antennas AVMD6600-SWA91RXA: Receive module with analog audio output and integrated printed PCB antennas AVNERA CORPORATION | 16505 NW BETHANY COURT SUITE 100 | BEAVERTON, OREGON 97006, U.S.A. | MAIN +1.503.718.4100 | FAX +1.503.718.4101 | WWW.AVNERA.COM AVNERA PROPRIETARY & CONFIDENTIAL | PROVIDED UNDER NDA AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 1 Table of Contents General Description ______________________________________________________________ 1 Applications ____________________________________________________________________ 1 Ordering Options ________________________________________________________________ 1 Features _______________________________________________________________________ 1 1 Table of Contents ____________________________________________________________ 2 2 Lists of Figures and Tables ____________________________________________________ 3 3 AVMD6600-SWA91-TXD/RXD/RXA Functional Block Diagrams _____________________ 4 4 AVMD6600-SWA91 Pin Information ____________________________________________ 7 5 AVMD6600-SWA91 Mechanical Dimensions______________________________________ 9 6 Electrical Specifications ______________________________________________________ 10 Absolute Maximum Ratings ______________________________________________________________ 10 Recommended Operating Range __________________________________________________________ 10 Electrical Characteristics ________________________________________________________________ 11 7 Application information ______________________________________________________ 12 7.1 Mechanical requirements ________________________________________________________________ 12 Application circuit ______________________________________________________________________ 13 7.2 7.3 External I2S Requirement _______________________________________________________________ 13 8 FCC and Industry Canada certification information _______________________________ 14 Label Information ______________________________________________________________________ 14 Equipment labeling requirements _________________________________________________________ 14 User manual labeling requirements ________________________________________________________ 15 9 Ordering Information _______________________________________________________ 16 10 Contact Information and Legal Disclaimer _____________________________________ 17 6.1 6.2 6.3 8.1 8.2 8.3 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 2 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 2 Lists of Figures and Tables Table 1: AVMD6600-SWA91 Module Block Diagram Description ___________________________________________ 6 Table 2: AVMD6600-SWA91 Pin Information ___________________________________________________________ 7 Table 3; AVMD6600-SWA91 Electrical Characteristics __________________________________________________ 11 Table 4: AVMD6600-SWA91 Module Ordering Information _______________________________________________ 16 Figure 1: AVMD6600-SWA91TXD Module Block Diagram................................................................................................ 4 Figure 2: AVMD6600-SWA91RXD Module Block Diagram ............................................................................................... 4 Figure 3: AVMD6600-SWA91RXA Module Block Diagram ................................................................................................ 5 Figure 4: AVMD6600-SWA91 mechanical dimensions ....................................................................................................... 9 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 3 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 3 AVMD6600-SWA91-TXD/RXD/RXA Functional Block Diagrams The AVMD6600-SWA91 module is available in three variations, Digital Input Transmitter, Digital Output Receiver and Analog Output Receiver. Note: The device does not have full I2S master capability and cannot generate MCLK as an output. SPI GPIO V3.3 EEPROM Antenna Diversity Switch Balun TWI SPI GPIO VBATT
(Slave) I2S RESET_N AV6600 RFP RFN 2.4-2.5GHz Printed PCB Antennas Antenna matching networks DSC LED Crystal LED SPI GPIO V3.3 Figure 1: AVMD6600-SWA91TXD Module Block Diagram 2.4-2.5GHz Printed PCB Antennas EEPROM Antenna Diversity Switch Balun TWI SPI RFP RFN Antenna matching networks GPIO VBATT
(Slave) I2S RESET_N AV6600 DSC LED Crystal LED I2S Audio Input RESET_N I2S Audio Output RESET_N Figure 2: AVMD6600-SWA91RXD Module Block Diagram CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 4 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 Figure 3: AVMD6600-SWA91RXA Module Block Diagram CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 5 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 Table 1: AVMD6600-SWA91 Module Block Diagram Description Interface SPI GPIO/ LED Description The AVMD6600s SPI interface is used to allow an external host to control the AV6600 IC and to facilitate testing of the module. The GPIO and LED lines allow buttons and LEDs to be connected to the AVMD6600-
SWA91 to allow the user to control the Audio Magic system and communicate the systems state to the user. Analog Audio These pins form the AVMD6600-SWA91RXA modules analog audio output. The analog ground on the module and should be isolated from the host systems ground to prevent the creation of noise-inducing ground loops. RESET_N This pin connects directly to the RESET_N pin on the AV6600 IC and is used to signal the module to power on and off. This pin provides power to all elements of the AVMD6600-SWA91. Internal regulators condition the input power according to the requirements of the various sub-circuit blocks. These input pins connect to the AV6600s digital audio interface and provide a digital audio input channel. The AVMD6600-SWA91 TXD is always an I2S slave while the AVMD6600-SWA91 RXD can be either a Slave or a Master I2S port but the module cannot generate MCLK as an output.. Depending upon module configuration the audio data direction will change. V3.3 I2S CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 6 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet 4 AVMD6600-SWA91 Pin Information Table 2: AVMD6600-SWA91 Pin Information Pin Name RXA Module Not Connected Pin Name TXD/RXD Module Not Connected Number Pin 1 2 Not Connected Not Connected 3 4 5 6 7 8 9 Not Connected Not Connected Not Connected LINE_OUT Not Connected LINE_OUT_COM GND V3.3 ADAT/GPIO1 GND V3.3 GPIO1 LRCLK/GPIO2 GPIO2 10 BCLK/GPIO3 GPIO3 11 12 13 14 15 LED LED RESET_N RESET_N CMP CMP S_MOSI/S_CLK/
GPIO12 S_MOSI/S_CLK/
GPIO12 S_MISO/S_SDA/
GPIO13 S_MISO/S_SDA/
GPIO13 16 S_SCLK/GPIO14 S_SCLK/GPIO14 Type Analog Ground Analog Ground Analog Input Analog Output Analog Ground Ground PRELIMINARY v0p1 Pin Description Audio section ground; must be connected to LINE_IN_COM at the audio source to minimize noise. Audio section ground. Both LINE_IN_COM and LINE_IN_COM2 must be isolated from system ground for best noise performance Reserved, not supported on these module configurations Mono Analog Audio Output Audio section ground. LINE_OUT_COM must be isolated from the system ground for best noise performance. Digital section ground. Tie to Pin 24 as close to the module as possible Main power supply (3.3 Volts) Power Digital I/O Multifunction; I2S digital Audio data output (Input for TXD, Output for RXD), General Purpose I/O Default = ADAT digital module Digital I/O Multifunction; I2S digital Audio frame clock input (Slave for TXD, Master/Slave for RXD ), General Purpose I/O Default = LRCLK digital module Digital I/O Multifunction; I2S digital Audio bit clock input (Slave for TXD, Master/Slave for RXD), General Purpose I/O Default = BCLK digital module LED drive line; current sink to GND Analog Output Digital Input Analog Input Digital I/O Multifunction, SPI slave serial data Active-LOW Reset input expecting open drain connection Comparator input; default function is sensing battery status Digital I/O Multifunction, SPI slave serial data input, I2C slave clock, General-
Purpose I/O Default = S_MOSI output, I2C slave data, General-
Purpose I/O Default = S_MISO Digital I/O Multifunction, SPI slave clock, General-Purpose I/O Default = S_SCLK CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 7 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 S_SSB/GPIO15 S_SSB/GPIO15 UART_RX/GPIO6 UART_RX/GPIO6 UART_TX/GPIO7 UART_TX/GPIO7 M_MOSI/M_SCL/
GPIO4 M_MOSI/M_SCL/
GPIO4 M_MISO/M_SDA/
GPIO6 M_MISO/M_SDA/
GPIO6 M_SCLK/GPIO8 M_SCLK/GPIO8 M_SSB/GPIO9 M_SSB/GPIO9 Digital I/O Multifunction, SPI slave select, Digital I/O Multifunction, UART receive, Digital I/O Multifunction, UART transmit, General-Purpose I/O Default = S_SSB General-Purpose I/O Default = GPIO6 General-Purpose I/O Default = GPIO7 Digital I/O Multifunction, SPI master serial data Digital I/O Multifunction, SPI master serial data output, I2C master clock, General-
Purpose I/O Default = M_SCL input, I2C master data, General-
Purpose I/O Default = M_SDA Digital I/O Multifunction, SPI master serial clock, General-Purpose I/O Default = GPIO8 Digital I/O Multifunction, SPI master serial select, General-Purpose I/O Default = GPIO9 Digital section ground. Tie to Pin 6 as close to the module as possible GND GND Ground 17 18 19 20 21 22 23 24 CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 8 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 5 AVMD6600-SWA91 Mechanical Dimensions Figure 4: AVMD6600-SWA91 mechanical dimensions CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 9 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 6 Electrical Specifications 6.1 Absolute Maximum Ratings Absolute Maximum Ratings (AMR) are stress ratings only. AMR corresponds to the maximum value that can be applied without leading to instantaneous or very short-term unrecoverable hard failure (destructive breakdown). Stresses beyond those listed under AMR may cause permanent damage to the device. Functional operation of the device at these or any other conditions beyond those indicated under Recommended Operating Range is not implied. Exposure to absolute-maximum-rated conditions for extended periods may adversely affect device reliability. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. CONDITION V3.3 Supply Voltage Input Input Voltage Range Digital Inputs1 Input Voltage Range Analog Inputs Operating Temperature Storage Temperature Assembly Temperature Static Discharge Voltage HBM2 Static Discharge Voltage MM3 MIN
-0.3V
-0.3V
-0.3V 0C
-40C MAX 3.6V 3.6V V3.3+0.3V
+70C
+100C TBD TBD TBD Notes:
Note 1: Digital GPIO Pins are 5V Tolerant when programmed as Inputs. Note 2: Terminology: HBM => ESD human body model Note 3: Terminology: MM => Machine model 6.2 Recommended Operating Range PARAMETER V3.3 Supply pin voltage Ambient Temperature (TA) MIN 3.0 0 TYP MAX 3.6 70 UNIT V C CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 10 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 6.3 Electrical Characteristics Test Conditions: TA=+25C, V3.3=3.3V Table 3; AVMD6600-SWA91 Electrical Characteristics CONDITIONS PARAMETER RF Frequency Range Audio Output Voltage1 Audio SNR Analog Output1 Audio SNR I2S Input/Output2 Analog Audio THD+N3 Range (LOS) I2S end to end Current consumption V3.3(Active Audio mode) TYP MAX UNIT 2477 MHz Vpk-pk 2 MIN 2405 88 94 tbd 15 50 dB dB dB m mA Note 1: AVMD6600-SWA91RXA module only Note 2: AVMD6600-SWA91TXD/RXD modules only Note 3: Measured at -3dbFS input, A weighting. Output is taken, using external DAC on Avnera development board. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 11 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 7 Application information 7.1 Mechanical requirements Figure 5: Recommended module antenna system clearance CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 12 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 7.2 Application circuit Schematics are provided separately. 7.3 External I2S Requirement The AVMD6600-SWA91 TXD module is an I2S slave only device and requires connection to a master I2S device to provide LRCLK and BCLK. The AVMD6600-SWA91 RXD module is normally an I2S slave and generates LRCLK, BCLK as well as I2S data out. The AVMD6600-SWA91 RXD module can be configured as an I2S master but is not capable of generating MCLK as an output so can only be used with external slave devices that contain some form of rate converter. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 13 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 8 FCC and Industry Canada certification information 8.1 Label Information The AVMD6600-SWA91 family of modules will be certified by the requirements set by the US Federal Communications Commission (Part 15) and Industry Canada (RSS-Gen, Issue 3, 2010-12 and RSS-210 issue 8, 2010-12) for certification as modular intentional radiators. The certification identification numbers are as follows:
US FCC ID: NKR-SWA9 Industry Canada (IC): 4441A-SWA9
* IDs will be provided after certification has been completed Avnera makes the following representations: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference,
(2) This device must accept any interference received, including interference that may cause undesired operation. Per FCC regulation 47 CFR 15.21: Changes or modifications not expressly approved by Avnera, as the party responsible for compliance, can void the users authority to operate the equipment using AVMD6600-SWA91 modules. 8.2 Equipment labeling requirements The statement shown below, or its equivalent, must appear on the external label of every piece of equipment that contains an AVMD6600 module. If the size of the final equipment is too small to support such a label, the statement described in must appear in the user manual for that equipment. Contains FCC ID NKR-SWA9 IC: 4441A-SWA9 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) This device must accept any interference received, including interference that may cause undesired operation CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 14 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 8.3 User manual labeling requirements The statements shown below, or their equivalents, must appear in the user manual for equipment containing AVMD6600-SWA91 modules:
Contains FCC ID NKR-SWA9 IC: 4441A-SWA9 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference
(2) this device must accept any interference received, including interference that may cause undesired operation Per FCC regulation 47 CFR 15.21: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 15 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 9 Ordering Information Table 4: AVMD6600-SWA91 Module Ordering Information Module Part Number SWA91TXD Option Code
-TXD Description Digital Input , 2mm Header, integrated printed PCB antennas Digital Output, 2mm Header, integrated printed PCB antennas Analog Output, 2mm Header, integrated printed PCB antennas SWA91RXD SWA91RXA
-RXD
-RXA CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 16 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 10 Contact Information and Legal Disclaimer Avnera Corporation 16505 Bethany Court, Suite 100 Beaverton, Oregon 97006 U.S.A. Main: +1.503.718.4100 Fax: +1.503.718.4101 www.avnera.com Avnera Corporation reserves the right to make changes without notice to the product to improve function, reliability, or performance. Avnera Corporation does not assume any liability arising from the application or use of the products or circuits described herein. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 17 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet FCC Statement PRELIMINARY v0p1 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
The end user has to be informed that the FCC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. If the size of the end product is smaller than 8x10cm, then additional FCC part 15.19 statement is required to be available in the users manual: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX FCC ID: NKR-SWA9 ". If the size of the end product is larger than 8x10cm, then the following FCC part 15.19 statement has to also be available on the label: This device complies with Part 15 of FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 18 AVNERA PROPRIETARY & CONFIDENTIAL AudioMagic AVMD6600-SWA91 Family Module Datasheet PRELIMINARY v0p1 IC Statement This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B conforme la norme NMB-003 du Canada. This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. This device and its antenna(s) must not be co-located or operation in conjunction with any other antenna or transmitter. IMPORTANT NOTE:
This module is intended for OEM integrator. The OEM integrator is still responsible for the IC compliance requirement of the end product, which integrates this module. Any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. USERS MANUAL OF THE END PRODUCT:
In the users manual of the end product, the end user has to be informed that the IC radio-frequency exposure guidelines for an uncontrolled environment can be satisfied. The end user has to also be informed that any changes or modifications not expressly approved by the manufacturer could void the user's authority to operate this equipment. IC statement is required to be available in the users manual: This Class B digital apparatus complies with Canadian ICES-003. Operation is subject to the following two conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. LABEL OF THE END PRODUCT:
The final end product must be labeled in a visible area with the following " Contains TX IC : 4441A-SWA9 ". CONTENTS SUBJECT TO CHANGE WITHOUT NOTICE 19 AVNERA PROPRIETARY & CONFIDENTIAL