FCC ID: NKR-KM66 WLAN Module

WLAN Module

(Wireless LAN Adaptor) Konica Minolta DAUB-KM66 User Manual Copyright Statement No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, whether electronic, mechanical, photocopying, recording or otherwise without the prior writing of the publisher. Pentium is trademark of Intel. All copyright reserved. Europe EU Declaration of Conformity This device complies with the essential requirements of the R&TTE Directive 1999/5/EC. The following test methods have been applied in order to prove presumption of conformity with the essential requirements of the R&TTE Directive 1999/5/EC:

-

IEC 60950-1:2005 (2nd Edition); Am 1:2009

- EN 60950-1:2006+A11:2009+A1:2010+A12:2011 Safety of Information Technology Equipment

- EN 62311: 2008 / Article 3(1)(a) and Article 2 2006/95/EC) Assessment of electronic and electrical equipment related to human exposure restrictions for electromagnetic fields (0 Hz-300 GHz)

- EN 300 328 V1.8.1: 2012-06

- Electromagnetic compatibility and Radio spectrum Matters (ERM); Wideband transmission systems; Data transmission equipment operating using wide band modulation techniques; Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive

- EN 301 893 V1.7.1: 2012-06

- Broadband Radio Access Networks (BRAN); 5 GHz high performance RLAN;

Harmonized EN covering the essential requirements of article 3.2 of the R&TTE Directive

- EN 301 489-1 V1.9.2: 2011

- Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment and services; Part 1: Common technical requirements

- EN 301 489-17 V2.2.1 2012

- Electromagnetic compatibility and Radio spectrum Matters (ERM); ElectroMagnetic Compatibility (EMC) standard for radio equipment; Part 17: Specific conditions for Broadband Data Transmission Systems

-

In Italy the end-user should apply for a license at the national spectrum authorities in order to obtain authorization to use the device for setting up outdoor radio links and/or for supplying public access to telecommunications and/or network services. 1 esky

[Jmno vrobce] tmto prohlauje, e tento [typ zazen] je ve shod se zkladnmi

[Czech]

poadavky a dalmi pslunmi ustanovenmi smrnice 1999/5/ES. Dansk Undertegnede [fabrikantens navn] erkl rer herved, at f lgende udstyr [udstyrets

[Danish]

typebetegnelse] overholder de v sentlige krav og vrige relevante krav i direktiv 1999/5/EF. Deutsch Hiermit erklrt [Name des Herstellers], dass sich das Gert [Gertetyp] in

[German]

bereinstimmung mit den grundlegenden Anforderungen und den brigen einschlgigen Bestimmungen der Richtlinie 1999/5/EG befindet. Eesti Kesolevaga kinnitab [tootja nimi = name of manufacturer] seadme [seadme tp = type

[Estonian]

of equipment] vastavust direktiivi 1999/5/E phinuetele ja nimetatud direktiivist tulenevatele teistele asjakohastele stetele. English Hereby, [name of manufacturer], declares that this [type of equipment] is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. Espaol Por medio de la presente [nombre del fabricante] declara que el [clase de equipo]

[Spanish]

cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999/5/CE.

[name of manufacturer] [type of equipment]

[Greek]

1999/5/. Franais Par la prsente [nom du fabricant] dclare que l'appareil [type d'appareil] est conforme

[French]

aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999/5/CE. Italiano Con la presente [nome del costruttore] dichiara che questo [tipo di apparecchio]

[Italian]

conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999/5/CE. Latviski Ar o [name of manufacturer / izgatavotja nosaukums] deklar, ka [type of equipment

[Latvian]

/ iekrtas tips] atbilst Direktvas 1999/5/EK btiskajm prasbm un citiem ar to saisttajiem noteikumiem. Lietuvi iuo [manufacturer name] deklaruoja, kad is [equipment type] atitinka esminius

[Lithuanian]

reikalavimus ir kitas 1999/5/EB Direktyvos nuostatas. Nederland Hierbij verklaart [naam van de fabrikant] dat het toestel [type van toestel] in s [Dutch]

overeenstemming is met de essentile eisen en de andere relevante bepalingen van 2 richtlijn 1999/5/EG. Malti Hawnhekk, [isem tal-manifattur], jiddikjara li dan [il-mudel tal-prodott] jikkonforma

[Maltese]

mal-tiijiet essenzjali u ma provvedimenti orajn relevanti li hemm fid-Dirrettiva 1999/5/EC. Magyar Alulrott, [gyrt neve] nyilatkozom, hogy a [... tpus] megfelel a vonatkoz alapvet

[Hungarian]

kvetelmnyeknek s az 1999/5/EC irnyelv egyb elrsainak. Polski Niniejszym [nazwa producenta] owiadcza, e [nazwa wyrobu] jest zgodny z

[Polish]

zasadniczymi wymogami oraz pozostaymi stosownymi postanowieniami Dyrektywy 1999/5/EC. Portugus

[Nome do fabricante] declara que este [tipo de equipamento] est conforme com os

[Portuguese]

requisitos essenciais e outras disposies da Directiva 1999/5/CE. Slovensko

[Ime proizvajalca] izjavlja, da je ta [tip opreme] v skladu z bistvenimi zahtevami in

[Slovenian]

ostalimi relevantnimi doloili direktive 1999/5/ES. Slovensky

[Meno vrobcu] tmto vyhlasuje, e [typ zariadenia] spa zkladn poiadavky a vetky

[Slovak]

prslun ustanovenia Smernice 1999/5/ES. Suomi

[Valmistaja = manufacturer] vakuuttaa tten ett [type of equipment = laitteen

[Finnish]

tyyppimerkint] tyyppinen laite on direktiivin 1999/5/EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen. 3 Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

- Reorient or relocate the receiving antenna.

-

Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC Caution: Any changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate this equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. IMPORTANT NOTE:

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Country Code selection feature to be disabled for products marketed to the US/CANADA 4 Operation of this device is restricted to indoor use only This device is intended only for OEM integrators under the following conditions:

1) The antenna must be installed such that 20 cm is maintained between the antenna and users, and 2) The transmitter module may not be co-located with any other transmitter or antenna, 3) For all products market in US, OEM has to limit the operation channels in CH1 to CH11 for 2.4G band by supplied firmware programming tool. OEM shall not supply any tool or info to the end-user regarding to Regulatory Domain change. As long as 3 conditions above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed IMPORTANT NOTE In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the FCC authorization is no longer considered valid and the FCC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate FCC authorization. End Product Labeling The final end product must be labeled in a visible area with the following: Contains FCC ID: NKR-KM66. Manual Information to the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. Antenna info. Antenna Peak gain ( dBi ) Model Type Connector 2400~2483.5MHz 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz Wi Fi up Printed NA Wi Fi down Printed NA 3.26 4.15 3.3 3.1 3.17 3.1 3.31 2.73 3.33 2.65 5 Industry Canada statement:

This device complies with Industry Canadas licence-exempt RSSs. Operation is subject to the following two conditions:

(1) This device may not cause interference; and

(2) This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1) lappareil ne doit pas produire de brouillage;

2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Caution:

(i) the device for operation in the band 51505250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

(ii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;

(iii) for devices with detachable antenna(s), the maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and Operations in the 5.25-5.35GHz band are restricted to indoor usage only. Avertissement:

(i) les dispositifs fonctionnant dans la bande de 5150 5250MHz sont rservs uniquement pour une utilisation l'intrieur afin de rduire les risques de brouillage prjudiciable aux systmes de satellites mobiles utilisant les mmes canaux;

6

(ii) pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis pour les dispositifs utilisant les bandes de 5250 5350MHz et de 5470 5725 MHz doit tre conforme la limite de la p.i.r.e;

(iii)pour les dispositifs munis d'antennes amovibles, le gain maximal d'antenne permis

(pour les dispositifs utilisant la bande de 5725 5850 MHz) doit tre conforme la limite de la p.i.r.e. spcifie pour l'exploitation point point et l'exploitation non point point, selon le cas;

Les oprations dans la bande de 5.25-5.35GHz sont limits un usage intrieur seulement. Radiation Exposure Statement:

This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. Dclaration d'exposition aux radiations:

Cet quipement est conforme Canada limites d'exposition aux radiations dans un environnement non contrl. Cet quipement doit tre install et utilis distance minimum de 20cm entre le radiateur et votre corps. This device is intended only for OEM integrators under the following conditions:

1) The transmitter module may not be co-located with any other transmitter or antenna. As long as 1 condition above are met, further transmitter test will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required with this module installed. Cet appareil est conu uniquement pour les intgrateurs OEM dans les conditions suivantes:

1) Le module metteur peut ne pas tre complant avec un autre metteur ou antenne. Tant que les 1 condition ci-dessus sont remplies, des essais supplmentaires sur 7 l'metteur ne seront pas ncessaires. Toutefois, l'intgrateur OEM est toujours responsable des essais sur son produit final pour toutes exigences de conformit supplmentaires requis pour ce module install. IMPORTANT NOTE:

In the event that these conditions can not be met (for example certain laptop configurations or co-location with another transmitter), then the Canada authorization is no longer considered valid and the IC ID can not be used on the final product. In these circumstances, the OEM integrator will be responsible for re-evaluating the end product

(including the transmitter) and obtaining a separate Canada authorization. NOTE IMPORTANTE:

Dans le cas o ces conditions ne peuvent tre satisfaites (par exemple pour certaines configurations d'ordinateur portable ou de certaines co-localisation avec un autre metteur), l'autorisation du Canada n'est plus considr comme valide et l'ID IC ne peut pas tre utilis sur le produit final. Dans ces circonstances, l'intgrateur OEM sera charg de rvaluer le produit final (y compris l'metteur) et l'obtention d'une autorisation distincte au Canada. End Product Labeling The final end product must be labeled in a visible area with the following: Contains IC:

4441A-KM66. Plaque signaltique du produit final Le produit final doit tre tiquet dans un endroit visible avec l'inscription suivante:

"Contient des IC: 4441A-KM66". Manual Information To the End User The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the users manual of the end product which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual. 8 Manuel d'information l'utilisateur final L'intgrateur OEM doit tre conscient de ne pas fournir des informations l'utilisateur final quant la faon d'installer ou de supprimer ce module RF dans le manuel de l'utilisateur du produit final qui intgre ce module. Le manuel de l'utilisateur final doit inclure toutes les informations rglementaires requises et avertissements comme indiqu dans ce manuel. Antenna info. Antenna Peak gain ( dBi ) Model Type Connector 2400~2483.5MHz 5150~5250MHz 5250~5350MHz 5470~5725MHz 5725~5850MHz Wi Fi up Printed NA Wi Fi down Printed NA 3.26 4.15 3.3 3.1 3.17 3.1 3.31 2.73 3.33 2.65 Taiwan Statement 1. 2. :

CCAFXXLPXXXXTX) 9 Table of Contents 1. INTRODUCTION 2. DRIVER/UTILITY INSTALLATION / UNINSTALLATION 3. CONNECTING TO AN EXISTING NETWORK 4. MODIFYING A WIRELESS NETWORK 10 1. Introduction Thank you for purchasing the 802.11 a/b/g/n/ac USB Wireless LAN Module that provides the easiest way to wireless networking. This User Manual contains detailed instructions in the operation of this product. Please keep this manual for future reference. System Requirements

- 128 MB of RAM or later (recommended)

- 300 MHz processor or higher 2. Driver/Utility Installation The driver should have been installed before the MULTI-FUNCTION PRINTER is shipped from the manufacturer. You can start using its network function without installing driver or utility. 3. Connecting to an Existing Network 1. Use the remote control that came with your MULTI-FUNCTION PRINTER to access the network configuration settings page. 2. Select the scanning wireless network function. The system starts to scan for available network. On this list, click Refresh to refresh the list at any time 3. Select the network you want to connect to. 4. If the chosen network has security enabled, you will have to setup corresponding security parameter. Contact the network manager for the correct settings. Select the security type and fill in required parameters. The options include the following:

WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None 11 4. Modifying a Wireless Network 4.1 Modifying General Settings 1. Use the remote control that came with your MULTI-FUNCTION PRINTER to access the network configuration settings page. 2. From the profile list, select one profile and choose the modify function. 3. Modify the settings below for your network. Profile Name Identifies the configuration wireless network profile. This name must be unique. Profile names are not case sensitive. Client Name Identifies the client machine. Use this profile for Configures station to operate in Access Point mode. Access Point mode Network Names The IEEE 802.11 wireless network name. This field

(SSIDs) has a maximum limit of 32 characters. Configure up to three SSIDs (SSID1, SSID2, and SSID3). 12 4.2 Modifying Security Settings 1. Use the remote control that came with your MULTI-FUNCTION PRINTER to access the network configuration settings page. 2. Select a security option of this wireless network. This product provides security options below. Contact your wireless network administrator for choosing a correct option. WPA/WPA2/CCKM WPA/WPA2 Passphrase 802.1x Pre-Shared Key (Static WEP) None WPA/WPA2 WPA/WPA2 Passphrase 802.1x Pre-Shared Key

(Static WEP) Enables the use of Wi-Fi Protected Access (WPA). Choosing WPA/WPA2 opens the WPA/WPA2 EAP drop-down menu. The options include:

EAP-FAST EAP-TLS EAP-TTLS EAP-SIM PEAP (EAP-GTC) PEAP (EAP-MSCHAP V2) LEAP Enables WPA/WPA2 Passphrase security. Click on the Configure button and fill in the WPA/WPA2 Passphrase. Enables 802.1x security. This option requires IT administration. Choosing 802.1x opens the 802.1x EAP type drop-down menu. The options include:

EAP-FAST EAP-TLS EAP-TTLS EAP-SIM PEAP (EAP-GTC) PEAP (EAP-MSCHAP V2) LEAP Enables the use of pre-shared keys that are defined on both the access point and the station. To define pre-shared encryption keys, choose the Pre-Shared Key radio button and click the Configure button to fill in the Define Pre-Shared Keys window. 13 None Allow Association to Mixed Cells Limit Time for Finding Domain Controller To Group Policy Delay No security (not recommended). Check this check box if the access point with which the client adapter is to associate has WEP set to Optional and WEP is enabled on the client adapter. Otherwise, the client is unable to establish a connection with the access point. Check this check box and enter the number of seconds (up to 300) after which the authentication process times out when trying to find the domain controller. Entering zero is like unchecking this check box, which means no time limit is imposed for finding the domain controller. Note: The authentication process times out whenever the authentication timer times out or the time for finding the domain controller is reached. Specify how much time elapses before the Windows logon process starts group policy. Group policy is a Windows feature used by administrators to specify configuration options for groups of users. The objective is to delay the start of Group Policy until wireless network authentication occurs. Valid ranges are from 0 to 65535 seconds. The value that you set goes into effect after you reboot your computer with this profile set as the active profile. This drop-down menu is active only if you chose EAP-based authentication. 14