MODEL WSP-R240
(2inch Mobile Printer) Rev. 6.5 All specifications are subjected to change without notice http://www.woosim.com WSP-R240 Rev. 6.5 Copyright WSP-R240 2inch mobile printer operators manual. Copyright 2022 by Woosim Systems Inc. All rights reserved. The information contained in this manual is the property of Woosim Systems Inc. And may not be reproduced in whole or in part without the prior written permission of Woosim Systems Inc. Trademark a registered trademark of Woosim Systems Inc. All other trademark are the properties of their respective companies. Caution Some semiconductor devices are easily damaged by static electricity. You should turn the printer OFF, before you connect or removed the cable on the rear side, in order to guard the printer against the static electricity. If the printer is damaged by the static electricity, you should turn the printer OFF. Notice The contents of this manual are subject to change without notice. http://www.woosim.com 2 WSP-R240 Rev. 6.5 Introduction The WSP-R240 is suitable designed for use with a growing variety of mobile devices. Bluetooth/Serial interfaces make the WSP-R240 the perfect comrade for applications such as point of transaction warehousing, distribution, point of sales, hospitality, gaming and healthcare. The general features of WSP-R240 printer are as follows:
Pocket size (79.5 X 114.3 X 43.5mm) Light weight (201g) for true mobility. Very silent printing thru direct thermal printing method. High speed(100mm/sec, MAX) High resolution(203dpi : 8dots/mm) UART(RS-232C or TTL), Bluetooth V5.2 Interface Intuitive LEDs indicate Power(on/off),Error, Bluetooth status, Battery status Support Magnetic Stripe Reader [option]. Support text and graphic printing. Easier paper loading by CLAMSHELL design. One touch paper cover Printer door open & Paper-out sensor Easier maintenance with self-diagnostics. In field programming Update Firmware, Download Fonts and Logos Microsoft Windows/Windows CE, Linux, Android, iOS compatible Free fall: 1.5M Flow control : Software (XON/XOFF) Hardware flow control not supported in printer. http://www.woosim.com 3 WSP-R240 Rev. 6.5 Operating Precautions Please follow the precautions below to enjoy and maintain the full performance of the printer. Using the Printer Be careful not to drop or bump the printer on a hard surface. Do not install the printer in direct sunlight or such areas. Suitable environment for the use of the printer is as follows:
Operating temperature : -10C to 50C Relative humidity
: 30% to 80%
Do not install the printer near devices that generate strong electromagnetic fields such as a copy machine. Do not open the platen cover during printing . Do not remove or reinstall the communication cable during printing or transmission. Do not touch the connectors of the communication during printing. Switch the POWER OFF when not in use. Do not use other solvent. The AC adapter, the battery charger and the battery pack may become warm when in use. This is normal and is not a malfunction. When the battery pack is used at low temperature, the length of time the printer can be used may be shortened. Thermal Paper Handling Store the thermal paper in a cool, dry and dark place. Do not rub the paper with hard object. Do not leave the paper with hard object. Do not allow plastic film, erasers, or adhesive tape to touch the paper for long periods. Do not stack the thermal paper with diazo copies immediately after copying or wet-type copies. Do not use chemical glue. Always use the clean thermal paper. http://www.woosim.com 4 WSP-R240 Rev. 6.5 Federal Communications Commission Radio Frequency Interference Statement FCC ID : QDDWSP-R240W This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. CAUTION: Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Modifications not expressly approved by the manufacturer could void the user's authority to operated the equipment under FCC rules. This Device has been evaluated to comply with RF exposure requirement for general use limit in portable condition. It is safe to be used in sold condition. CE WARNING Changes and modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. It is desirable that it be installed and operated with at least 20cm or more between the radiator and persons body(excluding extremities hand, wrists, feet, and ankles) http://www.woosim.com 5 WSP-R240 Rev. 6.5 CONTENTS 1. Outline ......................................................................................................................................................................... 7 1.1. Model classifications ......................................................................................................................................... 7 1.2 Symbol .................................................................................................................................................................. 7 1.3. Product Part Number System .......................................................................................................................... 8 1.4. Specifications. .................................................................................................................................................... 9 2. Setting up the printer ............................................................................................................................................ 11 2.1. Printer & Accessories ...................................................................................................................................... 11 2.2. Printer Features ................................................................................................................................................ 12 2.3. Replacing the paper roll ................................................................................................................................. 14 2.4. Power supply .................................................................................................................................................... 15 2.4.1. Internal power supply............................................................................................................................ 15 2.4.2. Installing the Battery ............................................................................................................................. 15 2.4.3. Recharging the battery ......................................................................................................................... 16 2.5. Set operation mode ........................................................................................................................................ 17 3. Interface ..................................................................................................................................................................... 21 3.1. UART(RS-232C or TTL) .................................................................................................................................... 21 3.2. Bluetooth ........................................................................................................................................................... 22 3.3. Read a magnetic stripe card (option) .......................................................................................................... 22 4. Using the printer ..................................................................................................................................................... 23 4.1. Control panel .................................................................................................................................................... 23 4.2. The self test ...................................................................................................................................................... 24 4.3. Using the Belt clip ........................................................................................................................................... 24 5. Consumable Parts ................................................................................................................................................... 25 5.1. Recommended paper ..................................................................................................................................... 25 5.2. Printing position .............................................................................................................................................. 25 6. Revision History ...................................................................................................................................................... 26 http://www.woosim.com 6 WSP-R240 Rev. 6.5 11.. OOuuttlliinnee 11..11.. MMooddeell ccllaassssiiffiiccaattiioonnss WSP-R240 ( ) ( ) Model Interface A1:UART/Bluetooth Power None : DC 8.4V 11..22 SSyymmbbooll Standby symbol IEC 5009, the standby symbol(line partially within a broken circle), Indicates a sleep mode or low power state. Direct current symbol This symbol is found on many electronic devices that either require or produce direct current. http://www.woosim.com 7 WSP-R240 Rev. 6.5 11..33.. PPrroodduucctt PPaarrtt NNuummbbeerr SSyysstteemm Model name / Interface Spec. S40 SC30 W25
. Wired Wireless 1 2 0 Bluetooth IrDA None A B C D E Z RS-232C TTL USB RS-485 Parallel None Example) 1. Porti-S40 UART/Bluetooth Part No. S40/A1 2. Porti-SC30 Bluetooth Only Part No. SC30/Z1 Note) The above table is the interface format which is supported. But some of the interfaces are not supported according to the product and please contact us, if you have any questions regarding the interface. http://www.woosim.com 8 11..44.. SSppeecciiffiiccaattiioonnss.. WSP-R240 Rev. 6.5 Item Specification Printing method Direct thermal line printing Character size Characters per line Optional Characters
- Font Size A: 12X24 / Font Size B : 9X24 / Font Size C : 8X16
- KOR : 24X24(16X24) / CHN, JPN : 24X24
- Font A : 32cpl / Font B : 42cpl / Font C : 48cpl
- KOR, CHN, JPN : 16cpl Alphanumeric:95, Extended Graphics:128X50 pages, International:10, Simplified/Traditional Chinese, Japanese, Korean(optional) Resolution Print width 203dpi, 8dots/mm 2-inch (48mm, 384dots) Printing speed 100mm / sec (MAX) Dimensions 79.5 X 114.3 X 43.5mm 79.5 X 118.2 X 43.5mm (MSR Model) Weight (w/o paper) 201g / 217g (MSR model) Interface UART(RS-232C or TTL) , Bluetooth V5.2 Paper supplied Thermal roll paper, Label roll (58mm wide, 40) 1-dimension : UPC-A, UPC-E, EAN-8, EAN-13, CODE-39, CODE-93, CODE-128, ITF, CODABAR Barcode supplied 2-dimension : PDF417, Micro PDF417, Truncated PDF417, QR-CODE, DATA Matrix, Maxicode Etc :GS1 databar Driver Microsoft Windows, Linux H/W spec. MCU : RX-32bit, RAM : 128M bit, FLASH : 64M bit Receive buffer size 1M bytes Sensor Support Cover open, Paper, Label MSR (option) Triple tracks (1&2&3 Tracks Reading)
*Supports 3DES & AES encryption
(Continue) http://www.woosim.com 9 WSP-R240 Rev. 6.5 Item Battery Specification Rechargeable 7.4V DC , 1150mAh (Li-ion) Battery duration 1 hour continuous printing Battery Charger Input (100~240V AC, 50~60Hz) Output(8.4VDC/0.8A), 4hours full charge time Temperature (operating) 0C ~ 45C (Charging)
-10C ~ 50C (Discharging) Environment Conditions
* Under 0C , density mode high is recommended. Temperature (storage)
-20C ~ 70C (storage) Humidity 30% - 80% (operating) 10% - 90% (storage) MCBF (Mean Cycle Mechanical 37,000,000 lines Between failure) Head Approximately 50 Km
< Table 1 >
http://www.woosim.com 10 WSP-R240 Rev. 6.5 22.. SSeettttiinngg uupp tthhee pprriinntteerr 22..11.. PPrriinntteerr && AAcccceessssoorriieess Your printer box should include these items. If any items are damaged or missing, please contact your dealer for assistance. Battery Pack Thermal roll paper Belt Clip Battery charger Communication cable WSP-R240 OPTIONAL External Battery Cradle MSR http://www.woosim.com 11 22..22.. PPrriinntteerr FFeeaattuurreess Part Name WSP-R240 Rev. 6.5 None MSR Model MSR Model http://www.woosim.com 12 Dimensions [Unit : mm]
WSP-R240 Rev. 6.5 None MSR Model MSR Model http://www.woosim.com 13 WSP-R240 Rev. 6.5 22..33.. RReeppllaacciinngg tthhee ppaappeerr rroollll Note : Be sure to use paper rolls that meet the specifications. Do not use paper rolls that have the paper glued to the core because the printer can not detect the paper end correctly. 1. Make sure that the printer is not receiving data; otherwise, data may be lost. 2. Open the paper cover as the One-Touch way by pressing the button in the arrow direction like the picture. 3. Insert the paper roll as shown. 4. Tear the excess paper off using the edge of paper door as a tear bar. http://www.woosim.com 14 WSP-R240 Rev. 6.5 22..44.. PPoowweerr ssuuppppllyy 22..44..11.. IInntteerrnnaall ppoowweerr ssuuppppllyy The following specification is requested for Power supply. Battery Charger : DC 8.4V/0.8A Avoid using power supply which its power capacity of power current is extremely high. 22..44..22.. IInnssttaalllliinngg tthhee BBaatttteerryy Warning :
Before installing or removing the battery pack, ensure the printer is OFF. If the printer is not used for long period of time, remove the battery pack from the printer. Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions. Batteries are provided not being charged. Please charge the battery before use. To install battery pack, proceed as follows:
-Insert the Battery Connector in the direction of the arrow. To remove battery pack, proceed the above order reverse. http://www.woosim.com 15 WSP-R240 Rev. 6.5 22..44..33.. RReecchhaarrggiinngg tthhee bbaatttteerryy For recharging the battery pack, install the battery pack in the printer. Insert the Battery Charger to the charge connector of the printer. Insert the Battery charger adaptor to the charge connector of the External Battery Cradle. NOTE : While charging the printer, turn off the printer power. Do not remove the battery during charging. The battery is consumable parts and when purchasing, compared to the use hour is gradually decreases. (Warranty 6 month) If the printer is not used for a long time, unplug the power cord from the printer and outlet. The recharging time depends on the voltage level and ambient temperature of the battery. Normally, if takes about 4 hours to recharge a battery pack. You must use only the supplied adapter. Red Lamp : charging the battery. Green Lamp : charging is finished. http://www.woosim.com 16 WSP-R240 Rev. 6.5 22..55.. SSeett ooppeerraattiioonn mmooddee In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode.
(refer to Table 2)
** Only the printer which support iOS Bluetooth interface comes out at the circumstance to change the printer mode. (Bluetooth Mode or Boluetooth(iAP) Mode).
** Manipulation methods :
1. Press Feed and Power buttons simultaneously until the ERROR lamp blinks 5 times and then keep pressing two buttons for 2 Seconds. 2. After the printer beeps twice, the Bluetooth mode is changed and it will print the result of change. 3. The changed mode can be checked in the printout. Example ) If the printer is in Bluetooth Mode Bluetooth(iAP) Mode If h i i i Bl h(iAP) M d Bl h M d
** If you want to change the Bluetooth Mode of printer, you need to disconnect the Bluetooth function of the current paired Smartphone.
** Methods :
1. Turn off the Bluetooth function of the current paired Smartphone.
(Blue LED is off.) 2. Change the printer mode.
(Additionally, we want to recommend you to rest(OFFON) the printer and change mode.) Printer LED status Android status iOS status http://www.woosim.com 17 WSP-R240 Rev. 6.5 POWER button : use for changing OPTION status. (Error Lamp) FEED button : use for changing MODE status. (Power Lamp)
[Example] The defaults of the printer are :
RS-232C / 9600 bps / 8 data bit / No parity / 1 stop bit / Density low / Mark use / Sensor low
/ Power down 5 minute If a user wants to modify the defaults with Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 stop bit / Density high / Mark no use
/ Sensor medium1 / Power down no use Press FEED & POWER Button during the Error Lamp flickers 5 times. You will see the Power Lamp and the Error Lamp flickers once. Press the POWER Button twice and the Error Lamp flickers 3 times. And then, interface mode has set to Bluetooth mode. When you press FEED button once again, Power Lamp flickers twice and the Error Lamp flickers once. Press POWER Button 3 times, Error Lamp flickers 4 times. And then, baudrate has set to 57,600 bps. When you press FEED button once again, Power Lamp flickers 3 times and the Error Lamp flickers twice. Press POWER Button once, Error Lamp flickers once. And then Data Bit has set to 7 data bit. When you press FEED Button once again, Power Lamp flickers 4 times and the Error Lamp flickers once. Press POWER Button once, Error Lamp flickers twice. And then the Parity bit has set to Odd parity bit. When you press FEED Button once again, Power Lamp flickers 5 times and Error Lamp flickers once. Press POWER Button once, Error Lamp flickers twice. And then the density has set to 2 stop bit. When you press FEED Button once again, Power Lamp flickers 6 times and Error Lamp flickers once. Press POWER Button twice, Error Lamp flickers 3 times. And then the density has set to Density high. http://www.woosim.com 18 WSP-R240 Rev. 6.5 When you press FEED Button once again, Power Lamp flickers 7 times and Error Lamp flickers twice. Press POWER Button once, Error Lamp flickers once And then the mark has set to Mark no use. When you press FEED Button once again, Power Lamp flickers 8 times and Error Lamp flickers once. Press POWER Button once, Error Lamp flickers twice And then the sensor has set to Sensor medium1. When you press FEED Button once again, Power Lamp flickers 9 times and Error Lamp flickers five times. Press POWER Button once, Error Lamp flickers once And then the power down has set to Power down no use. If all the mode have set, press the POWER Button and the FEED Button at the same time after then release the buttons at the same time. The printer will print out the mode status which has modified.
(Bluetooth / 57600 bps / 7 data bit / Odd parity / 2 stop bit / Density high /
Mark no use / Sensor medium1 / Power down no use) If the status is not correct, please try it again according to the procedure. http://www.woosim.com 19 MODE POWER Lamp ERROR Lamp
(Green)
(Red) Communication Port Baud Rate Data Bit Parity Stop bit Density Mark Sensor 1 2 3 4 5 6 7 8 Power Down 9 1 2 3 4 5 1 2 3 4 5 1 2 1 2 3 1 2 1 2 3 1 2 1 2 3 4 1 2 3 4 5 6 Option RS-232C RS-232C(Pro) Bluetooth Bluetooth(Pro) Bluetooth(iAP) 9600 bps 19200 bps 38400 bps 57600 bps 115200 bps 7 Data bit 8 Data bit No Parity Odd Parity Even Parity 1 stop bit 2 stop bit Density Low Density Medium Density High No use Use Low Medium1 Medium2 High No use 1 minute 2 minute 3 minute 4 minute 5 minute WSP-R240 Rev. 6.5
< Table 2 >
Notice : Bluetooth(iAP) is the mode which is used in iPod, iPhone and iPad Whole aspect. http://www.woosim.com 20 WSP-R240 Rev. 6.5 33.. IInntteerrffaaccee 33..11.. UUAARRTT((RRSS--223322CC oorr TTTTLL))
(Fig.3.1) The WSP-R240 printer has a UART(RS-232C or TTL) interface and is connected by means of a 5 pin mini USB socket. In the following table, the signals present on the Mini- USB socket are listed:
Pin No. Name Direction Function 1 2 3 4 5 TxD RxD GND NC GND Output Transmit Data Input Receive Data
Ground
Ground NOTE :
If you connect the printer interface cable is converted to UART mode. When data receiving, when it removes the communication cable, it loses a data. http://www.woosim.com 21 WSP-R240 Rev. 6.5 33..22.. BBlluueettooootthh Category Specification Bluetooth Spec. Bluetooth V5.2 / Class2 (10m) Frequency band 2402~2480 MHz Protocol Profile L2CAP, RFCOMM, SDP GAP, SDAP, SPP, GATT 33..33.. RReeaadd aa mmaaggnneettiicc ssttrriippee ccaarrdd ((ooppttiioonn)) Check the direction of the magnetic stripe and read the card. Holding the card as shown above, please pass at a steady speed (check the direction of the arrow). When the card reading is successful, buzzer sound one time. If it fails, buzzer sounds three times. http://www.woosim.com 22 WSP-R240 Rev. 6.5 44.. UUssiinngg tthhee pprriinntteerr 44..11.. CCoonnttrrooll ppaanneell
(Fig.4.1) Button
FEED Button:
When the printer is on, paper can be feed manually by pressing and holding the FEED button for more than one second.
- POWER Button:
When of 5 or more seconds presses and power comes to on or off. After pressing the POWER and the FEED button simultaneously, if the ERROR lamp 5 turn signals POWER button is converted with MODE functions.
: In keeping on pressing the Feed and Power button simultaneously until after the ERROR lamp blinks 5 times, the printer comes out at the circumstance to change the printer mode.
(Refer to 2.6. Set operation mode for details about mode conversion) LAMP
- Power : Printer is ON and ready to receive data.
(GREEN)
- Error : Indicates a fault condition or a printer error.
(RED) (details: no paper, paper cover opened. etc.)
- Bluetooth : Indicates a Bluetooth connection status.
(BLUE)
- Battery Power : These lamps(Green) indicated the battery power remaining.
(GREEN) The battery gain in quantity and these lamps are on the decrease. If so, you must recharge the battery by using the battery charger. http://www.woosim.com 23 WSP-R240 Rev. 6.5 44..22.. TThhee sseellff tteesstt Self-Test prints out the current setting value of printer. The way of self-test is as follows. 1. Insert proper paper into the printer. 2. Power on while pressing feed button to start self-test. 3. Printer will print out the current status. (F/W version and set contents) 4. And then pattern of characters will be printed out. 5. Self-test will be finished automatically and turned to the standby status. In case printer does not work properly, please contact Woosim customer service center. 44..33.. UUssiinngg tthhee BBeelltt cclliipp Following the instruction of the arrow, please put the belt clip in the hole and turn and fix the screw to the right by using a thing like a screw driver. Afterward, you can use it like the picture below http://www.woosim.com 24 WSP-R240 Rev. 6.5 55.. CCoonnssuummaabbllee PPaarrttss 55..11.. RReeccoommmmeennddeedd ppaappeerr Type
: Thermal Paper Paper width
: 58mm Paper thickness
: 605 Outer diameter
: 40mm or less Recording side
: Outside of roll Cautions 1. Do not paste the paper to the core. And the roll paper which has Near end mark printing on its near end is recommended. 2. Chemicals or oil may change the color of paper, or printed Characters may fade. 3. Change of paper color starts from approx 70 . Pay attention to heat, humidity and sun light. 4. Color of paper may be changed by being scratched by nail or hard metal, etc 55..22.. PPrriinnttiinngg ppoossiittiioonn http://www.woosim.com 25 WSP-R240 Rev. 6.5 66.. RReevviissiioonn HHiissttoorryy Date Version Comments Mar. 03. 2011 1.0 Initialize May. 03. 2011 2.0 Weight Change (215.3g -> 217g) Jan. 20. 2012 3.0
(only iPod, iPhone, iPad use) p18 : Bluetooth(iAP) Mode option Added Sensor option -> AUTO delete May. 10. 2012 4.0 p16 : Bluetooth Mode or Boluetooth(iAP) Mode setting additional Jul. 17. 2012 5.0 Printer door open & Paper-out sensor Added. p3 : One touch paper cover p8 : H/W Spec. change p3 : High speed(80 -> 100mm/sec, MAX) : p8 same Free fall : 1.5 -> 2M drop resistance Agency Approvals modify Aug. 08. 2013 6.0 P8 : General Spec. update Oct. 20. 2014 6.1 Jul. 01. 2016 6.2 p10 : Printer accessories modify p11-12 : MSR model figure additional p16 : Set operation mode modify p3 : Free fall : 2 -> 1.5M p21 : UART Pin spec modify Add contents of the note P25 : Add 4.3 Using belt clip p3,9,23 Bluetooth spec. update p3 p5 p7 p10 p15 p22 p23 p26
: Ver2.1+ EDR Ver3.0 Agency Approvals update Additional CE warning Additional Symbol(standby, DC current) Battery capacity modify : 1200 1130 Additional battery warnings Interface modify (USB part delete) 3.3 Read a magnetic stripe card(option) update 4.3 Using the belt clip image update May. 17. 2017 6.3 Feb. 12. 2020 Sep. 20. 2022 6.4 6.5 Change page layout (B5A4)
* Delete address p11-12 : Battery charger update(SHE) M3X M3W http://www.woosim.com 26 7..Regulatory Statement This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:
1. This device may not cause interference. 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes :
(1) lappareil ne doit pas produire de brouillage, et
(2) lutilisateur de lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. ISED Radiation Exposure Statement
(For Canada) This equipment complies with ISED radiation exposure limits set forth for an Uncontrolled environment. Avis d'industrie canada
(Pour le Canada) Cet appareil est conforme aux limites dexposition aux rayonnements dIndustrie Canada pour un environnement non contrl. NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USERS AUTHORITY TO OPERATE THE EQUIPMENT. REMARQUE : LE FABRICANT NEST PAS RESPONSABLE DES INTERFRENCES RADIOLECTRIQUES CAUSES PAR DES MODIFICATIONS NON AUTORISES APPORTES CET APPAREIL. DE TELLES MODIFICATIONS POURRAIENT ANNULER LAUTORISATION ACCORDE LUTILISATEUR DE FAIRE FONCTIONNER LAPPAREIL. http://www.woosim.com