FLUSH, Fastprk Magnetic Sensor Model: FP-GFLL Description The Fastprk sensor uses magnetic sensors to precisely detect the presence of vehicles. It houses advanced signal processing, meaning that it can differentiate between the various magnetic fields in its surroundings to achieve highly reliable detection. The Fastprk sensor uses radio communication protocols based on standard certified technology. The sensors are capable of direct communication with the Gateway within a radius of up to 500 metres. As it does not use repeaters, this solution enables significant savings in the installation of the network. Installation of the sensor The Fastprk sensor must be positioned in the centre of the parking space. It is important to make sure the ground is dry before performing the installation. The step-by-step procedure is as follows:
- Mark the spot where the sensor will go;
- Drill a 70 mm-deep hole with a diameter of 112 mm;
- Prepare the Mapegrout SV grout;
- Put approximately 250 ml of the grout in the hole;
-
- Leave the grout to dry for approximately 15 minutes. Insert the sensor and clean off any excess grout;
Calibration of the sensor Once the sensor is in its final position, it must be calibrated. To do so, you need the following tools:
- A smartphone with the Worldsensing calibration app installed;
- A Worldsensing RFID reader;
- The username and password provided by Worldsensing. Calibration process 1. Turn on Bluetooth on the smartphone. 2. Log into the app on the smartphone. 3. Press the power button on the RFID reader. 4. Go to Scan for device in order to find nearby devices. 5. Make sure there are no metallic objects within 3 metres of the sensor, for example cars, tools or fences. 6. In the app, press Discovery while holding the RFID reader close to the sensor. 7. The ID of the sensor will appear on the screen together with information about the calibration. 8. In the app, press Calibration. The sensors calibration process begins. 9. A minute later, press Report while holding the reader close to the sensor. 104 x 64 mm 435 g
-30C to +70C IP67 3.6 VDC 902 928 MHz 200 metres Li-SOCl2 Specifications Dimensions Weight Working temperature range Protection Power supply Communications frequency Distance to Gateway Battery type FCC/IC Regulatory notices Modification statement Worldsensing, S.L. has not approved any changes or modifications to this device by the user. Any changes or modifications could void the users authority to operate the equipment. Interference statement This device complies with Part 15 of the FCC Rules and Industry Canadas licence-exempt RSS standards. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Wireless notice This equipment complies with FCC and IC radiation exposure limits set forth for an uncontrolled environment. The antenna should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. FCC Class B digital device notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
-
- Connect the equipment into an outlet on a circuit different from that to which the Increase the separation between the equipment and receiver. receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. CAN ICES-3 (B) / NMB-3 (B) This Class B digital apparatus complies with Canadian ICES-003.