Manual BlueNiceCom III V1.4 Stand November 2004 AMBER wireless GmbH Albin-Kbis-Strae 18 51147 Kln Tel. 02203-6991950 Fax 02203-459883 eMail info@amber-wireless.de Internet www.amber-wireless.de Inhaltsverzeichnis 1 Allgemein.......................................................................................Fehler! Textmarke nicht definiert. 2 Technische Daten:.........................................................................Fehler! Textmarke nicht definiert. 3 Anschlussbelegung :..........................................................................................................................4 4 Abmessungen: ...................................................................................................................................5 5 Hinweise zum Layout:......................................................................................................................6 Stand November 2004, Version 1.4 Technische nderungen vorbehalten AMBER wireless GmbH, Tel. 02203-6991950, Fax 02203-459883 Email info@ amber-wireless.de Internet www.amber-wireless.de 1 General BlueNiceCom III Bluetooth-Modul with UART-interface and integrated Chip-antenna Integrated chip-antenne Bluetooth Class 2 Modul Serial Port Profile (SPP) UART interface GAP & SDP support AMBER wireless provides with the BlueNiceCom III a Bluetooth-module with an integrated chip-
antenna, based on LMX9820 from National Semiconductor. This compact and inexpensive Bluetooth-
version is qualified for a serial data transmission. BlueNiceCom III comes with a SPP profile (Serial Port Profile) and works with other Bluetooth modules which support the same profile. Through the serial UART interface the BlueNiceCom will be connected to a processor or a direct to a system, according to the application. Via an external processor or host (PC) all further available application profiles could be set on the SPP-
profile, for example: Dial up Networking Profile, Fax Profile, LAN Access Profile. The module has an integrated chip-antenna and can placed into a circuit like a SMD-part. The controlling and setting is raised by a host processor. The module can be integrated easily in a system. According to the application and the settings the BlueNiceCom II can be work as a stand-alone-slave-
module. For a cable replacement or a point-to-multipoint (piconet) application a controlling through a processor is necessary. Up to 3 slaves could be managed by a master module. 2 Technical data:
2,85V to 3,6V typ. 65 mA typ. 0 dBm typ. 77dBm 9,6 kbps to 115kbps according to LMX9820
-10 bis +55, optional an extended temperature range is possible 27,5 x 16 x 3,5 mm All further technical datas according to the LMX9820 Modul of National Semiconductor BlueNiceCom III Voltage supply Current consumption RF output Rx Sensitivity Datarate UART:
Interface Operating temperature Dimension Miscellaneous Order number Stand November 2004, Version 1.4 Technische nderungen vorbehalten AMBER wireless GmbH, Tel. 02203-6991950, Fax 02203-459883 Email info@ amber-wireless.de Internet www.amber-wireless.de 3 Pin assignment :
Antenne Pin Nr. Signal of BlueNiceCom III 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 VCC ISEL1 ISEL2 RX TX RTS CTS RESET GND ENV1 ENV0 LSTAT_0 LSTAT_1 HOST_WU TX_SWITCH_P VDD_DIGI_PWR_D#
ST1 Signal of LMX 9820 Voltage supply (2,85V bis 3,6V) Input Isel1 of LMX9820 Input Isel2 of LMX9820 Input Uart_rx of LMX9820 Output Uart_tx of LMX9820 Output Uart_rts of LMX9820 Input Uart_cts of LMX9820 Input Reset_b and Reset_5100 of LMX9820 Ground Input Env1 of LMX9820 Input Env0 of LMX9820 Output Lstat_0 of LMX9820 Output Lstat_1 of LMX9820 Output Host_wu of LMX9820 Output TX_Switch_P of LMX9820 Input VDD_DIGI_PWR_D# of LMX9820 The signal level correspond to the power supply (2,85V bis 3,6V) of BlueNiceCom III and must be aligned if the Hostsystem has a different signal level. Stand November 2004, Version 1.4 Technische nderungen vorbehalten AMBER wireless GmbH, Tel. 02203-6991950, Fax 02203-459883 Email info@ amber-wireless.de Internet www.amber-wireless.de 4 Dimession:
BlueNiceCom III has 1mm x 2mm soldering pads with a raster of 2mm to be solder direct on a motherboard. Stand November 2004, Version 1.4 Technische nderungen vorbehalten AMBER wireless GmbH, Tel. 02203-6991950, Fax 02203-459883 Email info@ amber-wireless.de Internet www.amber-wireless.de 5 Details for Layout:
To achieve the maximum of range no metall has to be near or under the antenna. The antenna should have a distance of 8mm to any gound, strip line or component. Most suitable is to place the antenna at the margin of the motherboard. The figure shows the area which should be free of metal (ground, strip line, components, etc..). The area off 12mm between the soldering pads on the bottom side should (e.g. with adhesive tape) additional isolated, if any strip line is under the module to avoid any short circuit. 6 Soldering & Reflow Reflow appropriate The temperature curve depends on the motherboard its character. Depending on the limit values of the components following limits are not allowed to excess-
225C (LMX) 220C max. 10s (Chip-antenna) 200C max. 40s (Chip-antenna) Recommendation for Footprints:
Stand November 2004, Version 1.4 Technische nderungen vorbehalten AMBER wireless GmbH, Tel. 02203-6991950, Fax 02203-459883 Email info@ amber-wireless.de Internet www.amber-wireless.de Abbildung 1: Bluenicecom III Abbildung 2: Vorschlag for Footprint Further range of products around BlueNiceCom II:
Bluetoothmodules: BlueNiceCom I & II & III Evaluation-Kit:
1 BlueNiceCom II module; 1 2,4GHz antenna; 1 RS232 board with Sub-D-9 connector and LEDs; batteries for power supply; 1 USB-Bluetoothmodule for a second station to build up a Bluetooth radio link immediately, documentation and software. Software-Tools: C-Tools for controlling the LMX9820. AMBER wireless GmbH reserves for itself to change the mentioned data without announcement and takes no liability for technical inaccuracies and/or omissions. AMBER wireless GmbH Albin-Kbis-Strae 18 51147 Kln Tel. 02203-6991950 Fax 02203-459883 eMail info@amber-wireless.de Internet www.amber-wireless.de Stand November 2004, Version 1.4 Technische nderungen vorbehalten AMBER wireless GmbH, Tel. 02203-6991950, Fax 02203-459883 Email info@ amber-wireless.de Internet www.amber-wireless.de