all | frequencies |
|
exhibits | applications |
---|---|---|---|---|
manual |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 2 |
|
User's Manual | Users Manual | 1.79 MiB | ||||
1 2 | Attestation Statements | |||||||
1 2 | Attestation Statements | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Report | |||||||
1 2 | Attestation Statements | |||||||
1 2 | Test Setup Photos | |||||||
1 2 | External Photos | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Report | |||||||
1 2 | Internal Photos | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | ID Label/Location Info | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Cover Letter(s) | |||||||
1 2 | Test Setup Photos |
1 2 | User's Manual | Users Manual | 1.79 MiB |
FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Chelton Avionics Inc., dba Wulfsberg Electronics Division, a Cobham Avionics & Surveillance Group Company, hereafter referred to as Cobham Avionics, is located in Prescott, Arizona. Wulfsberg Electronics designs and manufactures the Wulfsberg Electronics C-5000 suite of products, including the FLEXCOMM, FLEXCOMM I and FLEXOMM II. For more than 25 years, Wulfsberg Electronics has distinguished itself by providing top quality avionics products for civil, air transport, and military applications. Wulfsberg Electronics makes no warranty, expressed or implied, with regard to this manual, including but not limited to any implied warranties of merchantability, fitness for a particular purpose, and non-
infringement. In addition, Wulfsberg Electronics makes no warranty with regard to the documentation or consequential, or any other damages in connection with or arising from furnishing, performance, or use of this manual. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment Reproduction of this publication or any portion thereof by any means is prohibited. For further information contact Sales, Wulfsberg Electronics, 6400 Wilkinson Drive, Prescott, Arizona, 86301. Telephone: (928) 708-1500. INFORMATION IN THIS MANUAL IS SUBJECT TO CHANGE WITHOUT NOTICE. 2009 WULFSBERG ELECTRONICS ALL RIGHTS RESERVED C-5000, FLEXCOMM, FLEXCOMM I, and FLEXOMM II are trademarks of Wulfsberg Electronics. Confidential and propriety to Chelton Avionics, Inc. Publication No. 150-041102 Rev E Page 2 of 88 C-5000 Operators Manual Rev Date Date Inserted By Rev Date Date Inserted By FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Record of Revisions Rev No. Rev No. A B C D E 10/04/2001 07/24/2008 11/19/2008 06/19/2009 07/29/2010 Publication No. 150-041102 Rev E Page 3 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Record of Revisions Date Inserted By Rev No. Rev Date Date Inserted By Rev No. Rev Date Publication No. 150-041102 Rev E Page 4 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual TABLE OF CONTENTS B. Transceiver Overview ..................................................................................................................12 C. FLEXCOMM II..............................................................................................................................12 D. FLEXCOMM I...............................................................................................................................12 E. FLITECOMM ................................................................................................................................13 F. Steps to Successful Setup and Operation ...................................................................................13 Section Page 1. Applicability ..........................................................................................................................................9 2. Glossary ...............................................................................................................................................9 Introduction.........................................................................................................................................12 3. A. Features ........................................................................................................................................12 G. Refer to Pilots Guide for C-5000 Operations ...............................................................................14 4. Configuration Availability ....................................................................................................................15 5. Configuring the C-5000 ......................................................................................................................18 G. Downloading a Configuration from RP into the C-5000...............................................................27 C. Configuring the C-5000 to Control A Non RT-5000 .....................................................................22 B. Configuring the C-5000 to Control an RT-5000 ...........................................................................20 K. Key Erase.....................................................................................................................................31 A. Configuring the C-5000................................................................................................................18 D. Setting Passwords .......................................................................................................................25 J. KVL Load .....................................................................................................................................30 I. Entering CPS Load Mode ............................................................................................................29 F. Configuring the C-5000 Using a PC.............................................................................................27 E. Setting Miscellaneous Configuration Options ..............................................................................26 H. Uploading a Configuration from the C-5000 into RP ...................................................................28 Publication No. 150-041102 Rev E Page 5 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual TABLE OF CONTENTS (CONTD) B. CPS Code PMA File Details ........................................................................................................32 A. Before you Begin..........................................................................................................................32 D. Feature Set ..................................................................................................................................34 C. Versioning ....................................................................................................................................33 B. Tracking .......................................................................................................................................33 C. Controls............ ..........................................................................................................................43 A. General...........................................................................................................................................33 A. Radio Wide ..................................................................................................................................34 B. NAT List .......................................................................................................................................42 Section Page 6. CPS Software Description and Programming ....................................................................................32 7. Radio Information ...............................................................................................................................33 8. Radio Configuration ...........................................................................................................................34 9. Conventional.......................................................................................................................................51 G. Quick-Call II..................................................................................................................................59 D. Display and Menu ........................................................................................................................44 E. Phone...........................................................................................................................................47 F. Secure..........................................................................................................................................47 F. MDC .............................................................................................................................................57 B. MPL..............................................................................................................................................52 H. DTMF ...........................................................................................................................................61 I. Singletone ....................................................................................................................................63 A. Conventional Configuration..........................................................................................................51 E. Status Alias List............................................................................................................................57 J. ASTRO Systems..........................................................................................................................63 C. Conventional Personality .............................................................................................................53 D. Message Alias List .......................................................................................................................57 Publication No. 150-041102 Rev E Page 6 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual TABLE OF CONTENTS (CONTD) B. Trunking System ..........................................................................................................................69 E. Type II Trunking Call List .............................................................................................................76 A. Trunking Configuration.................................................................................................................66 D. Trunking Call List .........................................................................................................................76 C. Trunking Personality ....................................................................................................................73 Section Page 10. Trunking..............................................................................................................................................66 11. Scan....................................................................................................................................................77 12. Zone Channel Assignment .................................................................................................................77 Appendix A CTCSS (PL) Tone Codes ......................................................................................................79 Appendix B Mode 2 Operation..................................................................................................................81 Appendix C Single Microphone Operation................................................................................................83 Appendix D Equivalent Part Number ........................................................................................................87 Publication No. 150-041102 Rev E Page 7 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual This page intentionally left blank. Publication No. 150-041102 Rev E Page 8 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 1. Applicability This manual describes how to configure and use Cobham C-5000 Communication Management Controllers with part numbers in the 31300-1X02-XXXX series (where X can be any digit), and the civil support software configuration. Although this manual is largely applicable to previous software versions, some recently added features may not be available, and minor operational changes in previously available features may exist. 2. Glossary AM Acronym for Amplitude Modulation. In this type of modulation, the amplitude of the signal is varied in proportion to the voice or data input signal. The signal quality can be severely degraded because of lightning or man made electrical noise. AM is only used in the frequency ranges 108 to 152 MHz and 225 to 400 MHz. All air traffic control functions use AM modulation. Audio Phase The RT-5000 can invert the phase of the audio signal during transmit or receive. This is sometimes necessary for DPL systems to work. Bandwidth A term used to describe the amount of frequency a channel has to transmit a signal. Two of the most common FM channel bandwidths are 12.5 kHz (Narrow) and 25 kHz (Standard). Some special signals, such as military encryption, work best when using 35 kHz (Wide) or 70 kHz (Extra-wide) channels. All of these bandwidths are available in the RT-5000. Channel A group of radio characteristics, such as RX & TX frequencies, modulation, power levels, etc. CMC An acronym for Communication Management Controller. The C-5000 is a CMC. CTCSS Acronym for Continuous Coded Squelch System. DCS Acronym for Digital Coded Squelch DES Acronym for Digital Encryption Standard. This is an algorithm by which signals are encrypted. Deviation The amount of peak change the RF signal varies from the carrier in proportion to the amplitude of the voice signal. DPL Acronym for Digital Private Line. Also known as DCS. DTMF Dual Tone Multiple Frequency. On a telephone keypad, each row and column have unique audio tones that are sent when a button is pushed. At the receiver, a decoder listens for a row tone and a column tone and can determine from that, which button has been pushed. Direct Also known as simplex, car-to-car, and talk-around. This mode of operation allows you to bypass the repeater and talk directly to another radio. TX and RX frequencies are the same. Encryption Method by which a signal is scrambled so that other listeners without the proper encryption key cannot understand what is being transmitted. Encryption Key When encrypting a transmission, the algorithm used to scramble the information requires both the transmitting and receiving devices to have a number. This number is called an Encryption Key. Some systems are limited to one key and others are capable of having multiple keys. Publication No. 150-041102 Rev E Page 9 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Flexcomm I First generation of Flexcomm control heads and transceivers. This includes the C-1000 control head and RT-30, RT-138(F), RT-450, RT-406F transceivers. Flexcomm II Second generation of Flexcomm control heads and transceivers. This includes the C-
5000 control head and RT-5000 multi-band transceiver. FM Acronym for Frequency Modulation. In this type of modulation, the frequency of the signal is varied from its center point in proportion to the amplitude of the voice or data signal. Most importantly, this type of modulation is not affected by lightning or other atmospheric noise. Guard Receiver Second receiver added to the transceiver to monitor a specific frequency. Some common guard frequencies are 121.5, 243, Marine channel 16, and Marine channel 70. However, this optional function can also be used to monitor a dispatch channel, or an important tactical frequency. Some Guard receivers have a single frequency that is set in hardware Other options, available only in the RT-5000, are a programmable dual channel receiver and a multi-band P25/Trunking compatible unit. IF Injection In a superhetrodyne receiver, high frequency signals are progressively lowered in frequency until only the audio is left. This is done by multiplying the RF Signal by a sinewave either above or below the RF carrier. Mathematically this results in an Intermediate Frequency (IF) that is the sum and difference of the two signals The RT-5000 has the capability of having either High (Above) or Low
(Below) the signal frequency What this means is if you have a signal interfering with the desired signal. Sometimes the interference can be eliminated by switching either the 2nd or 3rd injection setting. Interoperability The ability for different radio systems to communicate with each other directly. For example, when one manufacturers radio products will communicate with anothers, they are said to be Interoperable. ITM Internal Transceiver Module. This is the module that is physically placed in the Guard Receiver slot in the RT-5000. This is the part of the radio that can perform P-25, encryption, and Motorola Trunking. Each ITM covers a specific frequency band: 136-174, 380-470, 450-520, 764-870, and 806 870 MHz. Up to two ITMs can be put into one RT-5000 however one must be below 380 MHz and one above 380 MHz. KEYMAT Another name for an encryption key. KVL Acronym for Key Variable Loader. It is a Motorola product for loading encryption keys into an encryption capable radio. Main Receiver Full function receiver located in every transceiver. Manual Channel A special preset channel that allows the operator to manipulate channel information without going into programming mode. On the C-5000 this special channel is labeled ..M and is located at channel 0. MODE 1 Operational mode of the C-5000/RT-5000 system where the operator does not know there is a main and guard located in the transceiver. This simplifies the user interface dramatically. However, only one receiver, the main or the ITM module in the Guard is in operation at one time so only one channel is monitored. MODE 2 Operational mode of the C-5000/RT-5000 system where the main and guard receiver are both monitoring frequencies at the same time. The user interface is more complex in that the user must select using the silver soft buttons on the C-5000 which determine which channel to display and transmit on. Publication No. 150-041102 Rev E Page 10 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual OTAR Acronym for Over The Air Re-key. Method by which the Encryption Key is transmitted over the radio channel, hence over the air. P-25 Digital Modulation Standard. Page The contents of the display, sometimes called a screen or view. PL Acronym for Private Line, also known as CTCSS or sub-audible tone. Preset Channel A channel that has been programmed into the memory of a control head or transceiver. Private Another name for encryption. Repeat This mode of operation uses a ground or air based repeater to retransmit your signal to another radio. TX and RX frequencies are different. RP - Acronym for Remote Programmer. Cobhams software to program the C-5000 with channel information via a connector of the front of the C-5000 is called the RP Software. It is recommended that this method is used whenever possible to program the C-5000 memory. While front panel programming is available for emergencies, using the RP software is less prone to operator errors and automatically provides for memory backup in case of control head failure. CPS Acronym for Customer Programming Software. A Motorola PC application used for configuring, uploading, and downloading information into the RT-5000s Internal Transceiver Modules. RT System Another way of saying Receiver/Transmitter System. Most often, the term refers to a single transceiver. However, because the Flexcomm I transceivers can be grouped together and controlled as one radio, it can refer to more than one transceiver. The C-5000 can control up to two RT systems. RX Abbreviation for Receive Shadow Key Special encryption key used to encrypt the keys received during the OTAR process. Squelch level Signal level at which the radio will detect a strong enough signal by the radio and audio is allowed to go to the user. Transceiver A radio containing both a transmitter and a receiver, co-located in one box. Trunking A term used to describe a communication system that automatically assigns an available channel to the operator. This type of system can improve channel use to the point that more conversations are going on than channels available. There are many different Trunking systems available. Most are proprietary to each manufacturer. In other words, systems built by different radio manufacturers will NOT communicate with each other. Only the P25 Trunking standard guarantees interoperability. TX Abbreviation for Transmit. Volume Loudness of a voice signal Publication No. 150-041102 Rev E Page 11 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 3. Introduction The Cobham C-5000 Communication Management Controller (CMC) is a microprocessor-based control head device that controls one or two Cobham transceivers. The C-5000 supports the full line of Cobham FLITECOMM, FLEXCOMM I, and FLEXCOMM II transceivers. This manual is intended to quickly instruct the user on the basic operations of the C-5000 and also outline the advanced operations that set the C-
5000 apart from any other communication device. A. Features The C-5000 provides a host of powerful features, including 7200 transceivers. Note: Software versions 10 and below are only capable of 350 preset channels.
(1) Controls Cobham RT-5000, RT-406F, RT-450, RT-138(F), RT-30, RT-9600(F) and RT-
(2) 700 preset channels, programmable from the front panel or using Cobhams Remote Programmer software.
(3) Users can dial in frequencies, PL tones, and transmit power on two manual channels.
(4) Advanced multi-radio modes, such as Simulcast, Relay, Repeater, and Relay-Simulcast.
(5) Control encryption functions embedded in the RT-5000 transceiver such as APCO P25 compliant digital voice and encryption with Over the Air Re-key (OTAR) capability. Note: Applicable to units with Motorola ITMs installed (-06xx or greater). Note: One manual channel available per RT system. B. Transceiver Overview The C-5000 provides support for the Cobham FLITECOMM, FLEXCOMM I, and FLEXCOMM II transceivers. It is very important that users know the number and type of transceivers connected to the C-5000, since different transceivers have very different capabilities and features. Here is a summary of the supported transceivers and their capabilities:
1. FLEXCOMM II This product line consists of the RT-5000 AM/FM transceiver, which covers the 29.7 to 960 MHz frequency range. The optional Guard Receiver can be specified as a single channel crystal guard
(available in three frequency ranges), a tunable multi-channel guard (29.7 960 MHz), or a multi-
band digital-capable guard (available in four frequency ranges). RT-5000s are equipped with CTCSS and CS tones on both the Main and Guard Receivers. The MTM (digital-capable) Guard variant of the RT-5000 adds support for P25 and Trunking channels, with encryption and over-the-air-
re-key (OTAR) capability. 2. FLEXCOMM I This product line currently consists of the RT-30, RT-138F, and RT-406F transceivers. The C-5000 also supports the RT-118, RT-138, and RT-450 transceivers, which are no longer manufactured but remain in wide use. The RT-30, RT-138F, and RT-406F FM transceivers cover the 29.7 to 49.99 MHz, 138.0 to 173.9975 MHz, and 406.0 to 511.9975 MHz frequency ranges, respectively. These transceivers can be specified with a single-channel, crystal-controlled, Guard Receiver that operates on a customer specified frequency. An optional Guard Receiver CTCSS decoder with programmable Guard Receiver tone can also be specified. Publication No. 150-041102 Rev E Page 12 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 3. FLITECOMM This product line is no longer manufactured, but remains in wide use. It consisted of the RT-7200, RT- 9600, and RT-9600F transceivers. They were available with a two-channel, crystal-controlled, Guard Receiver that could be user-specified for any Guard frequency between 138.000 and 173.9950 MHz (RT-7200) or between 150.000 and 173.9975 MHz (RT-9600/9600F). They were equipped with CTCSS tones on both the Main and Guard Receivers. C. Steps to Successful Setup and Operation IMPORTANT!!! CPS PROGRAMING NOTES:
ZONE 1 CHANNEL 1 MUST BE ASSIGNED TO CONVENTIONAL (CNV) PERSONALITY 1, MUST USE DIFFERENT RECEIVE AND TRANSMIT FREQUENCIES, AND HAVE DIR/TALKAROUND ENABLED. ZONES MUST BE SET FOR A MAXIMUM OF 16 CHANNELS PER ZONE, EXCEPT WHEN UTILIZING SINGLE ZONE SETTINGS. DO NOT ENABLE SCAN ON ANY PERSONALITY. DO NOT CHANGE MENU OR DISPLAY OPTIONS. USE FACTORY SETTINGS ONLY. WHEN MIXING DIRECT AND NONDIRECT CHANNELS WITHIN A ZONE, CHANNEL 1 OF THAT ZONE MUST BE ASSIGNED TO CONVENTIONAL (CNV) PERSONALITY 1, MUST BE A DUPLEX FREQUENCY, AND MUST HAVE DIR/TALKAROUND ENABLED. The following checklist will help installers and initial users setup the C-5000 and RT-5000.
(1) Connect the C-5000 to the transceivers. Note part numbers of the Control Head and all transceivers. C-5000 Part Number = 31300-1X02- ____________ Radio #1 Model # = _________________ Part Number = ____________________ Radio #2 Model # = _________________ Part Number = ____________________
(2) Configure the C-5000 using the steps outlined in section 5 of this manual. You must know the last four digits of the C-5000 part number and the last four digits of any RT-5000s or the model type of any Flexcomm/Flitecomm Transceiver. Note: Your C-5000 software may not be updated to include all versions of RT-5000s. Use Appendix D to find alternative RT-5000 part numbers to enter.
(3) If Radio #1 is an RT-5000 that has a MTM Guard Receiver (-06XX or greater) connect a PC to the 9-pin programming port of the RT-5000 and run the Motorola CPS software.
(4) Put the C-5000 in CPS mode for radio #1 and select the first ITM (Internal Transceiver Module) to appear. Publication No. 150-041102 Rev E Page 13 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(5) Using the CPS software, read the codeplug out of the ITM. Save this first as a back-up in case you need to return to the factory setting.
(6) Modify system settings for your application. Program the personalities and assign Zone/Channels. It is important to use good channel identifiers so CPS operators can efficiently determine the purpose of the channel. Whenever possible, use the same channel names as used by the ground personnel to avoid using the wrong preset. Note: These steps require significant knowledge of the Motorola software. We encourage enlisting the help of someone familiar with Motorola CPS software to successfully program the ITM.
(7) Save the modified codeplug to the hard drive and load it into the ITM.
(8) Do the above for the second ITM if there is one in Radio #1.
(9) Do the above for Radio #2 only if its an RT-5000 with an MTM Guard (-06XX or greater).
(10) Using the front panel, or better yet the Cobham RpWin software, program all preset channels into the C-5000, including the ones programmed into each ITM module in the steps above.
(11) Using a communication analyzer or over the air test, verify that each radio and channel operates properly. D. Refer to Pilots Guide 150-041103 for C-5000 operations Publication No. 150-041102 Rev E Page 14 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 4. Configuration Availability PN 400-015525-XXXX Internal Transceiver Module
(MHz) 138-174 403-470 450-520 764-806 DES. / XL / OFB Encryption D.V.P. / XL Encryption D.V.I. / XL Encryption SmartNet Trunking SmartZone Trunking OTAR RT-5000 P/N options (with embedded XTS-3000 ITM modules)
-1311
-1111 E
-0811
-0711
- 0 1
-1011
-0911
-1211 E
-0611
- 0 2 E E E E E E
-1411
-02 X X X M P T Y S L O T X M P T Y S L O T
-04 M
- 0 3 M X X X P T Y S L O T X P T Y S L O T
-06 X X X M P T Y S L O T
-05 X M P T Y S L O T
- 0 8 X X X M P T Y S L O T
-07 X M P T Y S L O T X X X RT-5000 P/N options (with embedded XTS-3000 ITM modules) contd
-1511
-01
-1611
-02
-07 X
-07 X X X X X
- 0 8 X X X PN 400-015525-XXXX
-1711
-1811
-1911
-2011
-2111
-2211
-2311
-2411
-2511
-2611
-2711
-02
-01
-02
-01
-02
-01
-02
-01 450-520 764-806
-05
-08 X X
-05
-06 X X
-03
-06 X X
-03
-04 X X
-04 X 138-174
-01 403-470 Internal Transceiver Module
(MHz) D.E.S. / XL / OFB Encryption D.V.P. / XL Encryption D.V.I. / SL Encryption SmartNet Trunking SmartZone Trunking OTAR X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
-09 X
-10 X X E M P T Y S L O T E M P T Y S L O T Publication No. 150-041102 Rev E Page 15 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual RT-5000 P/N options (with embedded XTS-3000 ITM modules) contd
-3311
-3011
-2811
-2911
-3111
-3211 PN 400-015525-XXXX Internal Transceiver Module
(MHz) 138-174 403-470 450-520 764-806 A.E.S. Encryption D.E.S. / XL / OFB Encryption D.V.P. / XL Encryption D.V.I. / XL Encryption SmartNet Trunking SmartZone Trunking ASTRO P25 Trunking (3600 & 9600 BAUD) OTAR
-02 X E M P T Y S L O T
-12 X X E M P T Y S L O T
-13 X X X E M P T Y S L O T
-14 X E M P T Y S L O T E
-16
-15 M X X X P T Y S L O T X X X X E M P T Y S L O T
-3411
-3511
-16
-16 X X X X
-20 X X X
-18 X X X X X X X X X PN 400-015525-
XXXX
-5011
-5111
-5211
-5311
-5411
-5511
-5611
-5711
-5811
-5911
-6011 RT-5000 P/N options (with embedded XTS-5000 ITM modules) ITM Frequency 136-174
-04 380-470 450-520 806-870 A.E.S. Encryption D.E.S./XL/OFB Encryption D.V.P./XL Encryption D.V.I/ XL Encryption OTAR SmartZone/Omnilink P25 Trunking (3600 & 9600 BAUD) X X X X
-22 X X X X
-04
-04 X X X X
-11 X X X X X X X X
-16 X X X X
-22 X X X X Mod 7 N/A Mod 7 Mod 7 Mod 7 Mod 7 N/A 121.5 243.0 CH 16.0 CH 70.0 Vote Scan Search and Rescue Receivers E M P T Y S L O T
-10 X X X X Mod 7
-24 X X X X X E M P T Y S L O T
-16 X X X X Mod 7 E M P T Y S L O T
-04 X X X X Mod 7 E M P T Y S L O T
-23 X X X Mod 7 E M P T Y S L O T E M P T Y S L O T
-25 X X X Mod 7
-24 X X X X X
-26 X X X X X E M P T Y S L O T Continues......... Publication No. 150-041102 Rev E Page 16 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual RT-5000 P/N options (with embedded XTS-5000 ITM modules) (contd)
-8211
-9999
-6111 PN 400-015525-XXXX ITM Frequency 380-470 450-520
-27 806-870 A.E.S. Encryption D.E.S./XL/OFB Encryption D.V.P./XL Encryption D.V.I/ XL Encryption OTAR SmartZone/Omnilink P25 Trunking
(3600 & 9600 BAUD)
-28 X X X X
-10 X X X X Vote Scan Search and Rescue Receivers MOD 7 MOD 7 Mod 7 N/A 121.5 243.0 CH 16.0 CH 70.0 X X X X X X X X
-10 X X X X MOD 7 E M P T Y S L O T Note: The ITM dash number e.g. -02, -22 represents the ITM module option installed. Note: All P/N flavors come standard with the following features:
FM1 Main portion: 29.7-960 MHz FM & 29.7-400 MHz AM analog conventional capability. FM2 ITM portion: Project 25 Common Air Interface (CAI); conventional FM analog;
FM digital (ASTRO). Publication No. 150-041102 Rev E Page 17 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 5. Configuring the C-5000 A. Configuring the C-5000 Although Cobham highly recommends using the PC based Remote Programmer software to specify the C-5000s configuration, it can be specified from the front panel. The process is as follows.
(1) Ensure you are on the HOME PAGE.
(2) Press the PROG button. You will be prompted to enter a password, as follows. E N T E R P A S S W OR D 2
# = . .
< E N T E R >
(3) Input the appropriate password using the keypad and press the ENTER button. Note: Password 2 is 2222 by default.
(4) Press the MODE button until the following display page appears:
P R O G :
< E N T E R > = C F G SYST 2 = N E X T 3 = B A C K E M
(5) Press the ENTER button. You will be prompted to enter a password, as follows:
E N T E R P A S S W OR D 1
# = . .
< E N T E R >
(6) Input the appropriate password and press the ENTER button. Note: Password 1 is 1111 by default.
(7) The display will appear as follows:
S E T U P :
C 5 0 0 0 P / N = 1 220 2 = N E X T 3 = B A C K Publication No. 150-041102 Rev E Page 18 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(8) Use the cursor/value knobs to input the last four digits of your C-5000s part number. Press the MODE button to display the next menu page. S E T U P :
E N T E R = S E T UP 2 = N E X T 3 = B A C K I O # 1 RAD
(9) You can press the ENTER button to configure radio 1. Refer to the sections on configuring RT-5000 and non-RT-5000 radios for details on these sub-menu pages. Press the MODE button to display the next menu page. S E T U P :
E N T E R = S E T UP 2 = N E X T 3 = B A C K I O # 2 RAD
(10) You can press the ENTER button to configure radio 2. Refer to the sections on configuring RT-5000 and non-RT-5000 radios for details on these sub-menu pages. Press the MODE button to display the next menu page. S E T U P :
E N T E R = C H G P A S S W OR D 2 = N E X T 3 = B A C K 1
(11) You can press the ENTER button to change the system configuration password. Refer to the section on changing passwords for details on these sub-menu pages. Press the MODE button to display the next menu page. S E T U P :
E N T E R = C H G P A S S W OR D 2 = N E X T 3 = B A C K 2
(12) You can press the ENTER button to change the programming password. Refer to the section on changing passwords for details on these sub-menu pages. Press the MODE button to display the next menu page. S E T U P :
E N T E R = SET 2 = N E X T 3 = B A C K U P M I SC .
(13) You can press the ENTER button to change miscellaneous system properties, such as system encryption, side-tones, and de-emphasis. Refer to the section on miscellaneous configuration options for details on these sub-menu pages. Press the MODE button to display the next menu page. Publication No. 150-041102 Rev E Page 19 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual S Y S T E M S E T U P M O D E H O M E = E X I T 2 = R E V I E W
(14) Press the HOME button to exit system configuration, or the MODE button to review current settings. B. Configuring the C-5000 to Control an RT-5000 This section covers the radio setup sub-menu pages. Refer to the section on configuring the C-5000 for details on how to reach these menu pages. This section assumes the C-5000 part number you entered indicated an RT-5000 was present for Radio #1. We pick up at the following display page. S E T U P :
E N T E R = S E T UP 2 = N E X T 3 = B A C K I O # 1 RAD
(1) Press the ENTER button to begin configuring the RT-5000. S Y S R T - 5 0 0 0 P / N =
# 1 : 2 = N E X T 3 = B A C K 5 01 1
(2) Use the cursor/value knobs to input the last four digits of your RT-5000s part number. Press the MODE button to display the next menu page. Note: If the RT-5000 part number you enter is rejected, and you are sure you are entering a valid part number, it is likely your flavor of RT-5000 was created after the C-5000 software was released. Since the C-5000 software has no knowledge of this part number, it will reject it. Until your C-5000 software gets updated, you may enter an equivalent part number. Refer to Appendix D for a complete list. S Y S E N T E R = S E T UP
# 1 : 2 = N E X T 3 = B A C K
# 1 G UARD
(3) This page will only display if the RT-5000 part number entered indicates a Guard receiver is present. Pressing the ENTER button invokes the preset channel programming menu pages for the Guard channel. Refer to the section on programming a preset channel for details since programming a Guard channel is very similar to programming a preset channel. Publication No. 150-041102 Rev E Page 20 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual S Y S R A D I O M O D E = 1
# 1 : 2 = N E X T 3 = B A C K
(4) This page will only display if the RT-5000 part number entered indicates an ITM is present. Use the cursor/value knobs to select a value of 1 or 2. Mode 1 indicates that the ITM should act as part of the main transceiver, i.e. the two transceivers appear to be a single unit. Mode 2 indicates that the ITM should not act as part of the main, i.e. it should behave as a Guard receiver. Press the MODE button to display the next menu page. S Y S
# 1 : 2 = N E X T 3 = B A C K L E M O D E =
Z O N E IN G S
(5) This page will only display if the RT-5000 part number entered indicates an ITM is present. Use the cursor/value knobs to select a value of SINGLE or MULTI. SINGLE indicates that the ITM is configured for single-zone mode, which means all channels (up to 256) are programmed in zone 1. MULTI indicates that the ITM is configured for multi-zone mode, which means channels are dispersed across multiple (up to 16) zones. Press the MODE button to display the next menu page. Note: Software versions 10 and below will not have this feature available. I N C D E C 2 = N E X T 3 = B A C K M A I N S Q L = 1 6 0
(6) This page allows you to set the RT-5000s main receiver squelch level. Press the UPPER SOFT KEY to increase the squelch level, or the LOWER SOFT KEY to decrease squelch level. The squelch level determines the signal strength required by the RT-5000 to open its audio gates, allowing you to hear what it is receiving. The larger the number, the stronger the required signal. Press the MODE button to display the next menu page. I N C D E C G UARD 2 = N E X T 3 = B A C K 1 6 0 S Q L =
(7) This page allows you to set the RT-5000s guard receiver squelch level. Press the UPPER SOFT KEY to increase the squelch level, or the LOWER SOFT KEY to decrease squelch level. The squelch level determines the signal strength required by the RT-5000 to open its audio gates, allowing you to hear what it is receiving. The larger the number, the stronger the required signal. Press the MODE button to display the next menu page. Publication No. 150-041102 Rev E Page 21 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual S E T UP H O M E = E X I T RAD I O # 1 2 = R E V I E W
(8) Press the HOME button to exit the radio setup menu pages, or press the MODE button to review the current settings. C. Configuring the C-5000 to Control A Non RT-5000 This section covers the radio setup sub-menu pages. Refer to the section on configuring the C-5000 for details on how to reach these menu pages. This section assumes the C-5000 part number you entered indicated a Flitecomm or Flexcomm I radio was present on radio #2. We pick up at the following display page:
S E T U P :
E N T E R = S E T UP 2 = N E X T 3 = B A C K I O # 2 RAD
(1) Press the ENTER button to begin configuring the radio. S Y S
# 2 : 2 = N E X T 3 = B A C K T - N O R T - 3 0 PR ESEN
(2) Use the cursor/value knobs to tell the C-5000 if an RT-30 is present. Press the MODE button to display the next menu page. S Y S
# 2 : 2 = N E X T 3 = B A C K T - N O R T - 1 1 8 PR ESEN
(3) Use the cursor/value knobs to tell the C-5000 if an RT-118 is present. Press the MODE button to display the next menu page. S Y S R T - 1 3 8 PR
# 2 : 2 = N E X T 3 = B A C K T - Y E S ESEN
(4) Use the cursor/value knobs to tell the C-5000 if an RT-138 is present. Press the MODE button to display the next menu page. Publication No. 150-041102 Rev E Page 22 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual S Y S R T - 1 3 8
# 2 : 2 = N E X T 3 = B A C K T - N O F PR ESEN
(5) Use the cursor/value knobs to tell the C-5000 if an RT-138F is present. Press the MODE button to display the next menu page. S Y S R T - 4 5 0 PR
# 2 : 2 = N E X T 3 = B A C K T - N O ESEN
(6) Use the cursor/value knobs to tell the C-5000 if an RT-450 is present. Press the MODE button to display the next menu page. S Y S R T - 4 0 6
# 2 : 2 = N E X T 3 = B A C K T - N O F PR ESEN
(7) Use the cursor/value knobs to tell the C-5000 if an RT-406F is present. Press the MODE button to display the next menu page. S Y S R T - 9 6 0 0
# 2 : 2 = N E X T 3 = B A C K T - N O F PR ESEN
(8) Use the cursor/value knobs to tell the C-5000 if an RT-9600F is present. Press the MODE button to display the next menu page. S Y S R T - 9 6 0
# 2 : 2 = N E X T 3 = B A C K T - N O 0 PR ESEN
(9) Use the cursor/value knobs to tell the C-5000 if an RT-9600 is present. Press the MODE button to display the next menu page. S Y S R T - 7 2 0
# 2 : 2 = N E X T 3 = B A C K T - N O 0 PR ESEN
(10) Use the cursor/value knobs to tell the C-5000 if an RT-7200 is present. Press the MODE button to display the next menu page. Publication No. 150-041102 Rev E Page 23 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual S Y S G U A R D
# 2 : 2 = N E X T 3 = B A C K T - Y E S
# 1 PR ESEN
(11) Use the cursor/value knobs to tell the C-5000 if a Guard is present. Press the MODE button to display the next menu page. S Y S E N T E R = S E T UP
# 2 : 2 = N E X T 3 = B A C K
# 1 G UARD
(12) This page only appears if a guard is present. Press the ENTER button to configure the first Guard channel. Refer to the preset channel programming section for details on the menu pages that appear. Press the MODE button to display the next menu page. S Y S G U A R D
# 2 : 2 = N E X T 3 = B A C K T - Y E S
# 2 PR ESEN
(13) This page only appears if a second Guard is possible. Use the cursor/value knobs to tell the C-5000 if a second Guard is present. Press the MODE button to display the next menu page. S Y S E N T E R = S E T UP
# 2 : 2 = N E X T 3 = B A C K
# 2 G UARD
(14) This page only appears if a second guard is present. Press the ENTER button to configure the second Guard channel. Refer to the preset channel programming section for details on the menu pages that appear. Press the MODE button to display the next menu page. S Y S T O N E
# 2 : 2 = N E X T 3 = B A C K CT CS S - N O B O ARD
(15) Use the cursor/value knobs to tell the C-5000 if an internal CTCSS tone board is present.(Represented by a 3 in the C-5000 part number, i.e. 31300-XXXX-X333). Press the MODE button to display the next menu page. S Y S T O N E
# 2 : 2 = N E X T 3 = B A C K
- N O B O ARD DCS Publication No. 150-041102 Rev E Page 24 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(16) Use the cursor/value knobs to tell the C-5000 if an internal DCS tone board is present.
(Represented by a 3 in the C-5000 part number, i.e. 31300-XXXX-X333). Press the MODE button to display the next menu page. H O M E = E X I T 2 = R E V I E W I O # 2 RAD S E T UP
(17) Press the HOME button to exit the radio setup menu pages, or press the MODE button to review the current settings. D. Setting Passwords This section covers the password setup sub-menu pages. Refer to the section on configuring the C-
5000 for details on how to reach these menu pages. This section assumes we want to change password 1. The process is the same for password 2. We pick up at the following display page. S E T U P :
E N T E R = C H G P A S S W OR D 2 = N E X T 3 = B A C K 1
(1) Press the ENTER button to begin the password changing process. The display will appear as follows:
E N T E R N E W PA
# = . . SS W OR D 1
< E N T E R >
(2) Use the keypad to input the new password, and press the ENTER button. B A C K
# = . V E R I F Y
. .
< E N T E R >
I N P U T
(3) Use the keypad to re-input the new password, and press the ENTER button. This second entry is for verification. If you entered an inconsistent password, your input will be erased, and you may try again. Once you have entered the same password on both pages, it will be changed, and the display will revert to the following:
S E T U P :
E N T E R = C H G P A S S W OR D 2 = N E X T 3 = B A C K 1 Publication No. 150-041102 Rev E Page 25 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual E. Setting Miscellaneous Configuration Options This section covers the miscellaneous setup sub-menu pages. Refer to the section on configuring the C-5000 for details on how to reach these menu pages. We pick up at the following display page:
S E T U P :
E N T E R = SET 2 = N E X T 3 = B A C K U P M I SC .
(1) Press the ENTER button to begin configuring miscellaneous options. S E T U P :
D I M K E Y M O D E 2 = N E X T 3 = B A C K
- M UT E
(2) This page only appears if utilizing software 11 and above. Use the cursor/value knobs to tell the C-5000 if the DIM key should be used for the DIM function or the MUTE function. When configured for MUTE, pressing the DIM key will mute audio from the non-active receivers. Press the MODE button to display the next menu page. S E T U P :
2 = N E X T 3 = B A C K L E M I C M O D E
- S IN G
(3) This page only appears if using software 11 and above. Use the cursor/value knobs to tell the C-5000 if it has one or two microphones connected to it. When configured for SINGLE, the C-
5000 will operate in single-mic mode. Press the MODE button to display the next menu page. S E T U P :
S Y S T E M E N C R Y P T 2 = N E X T 3 = B A C K
- N O
(4) Use the cursor/value knobs to tell the C-5000 if external encryption is available. This option pertains only to a separate encryption device, i.e. one that is not part of the C-5000 or any of the transceivers. A KY-58 device is a typical example. Press the MODE button to display the next menu page. S E T U P :
C - 5 0 0 0 2 = N E X T 3 = B A C K S I D E T O N E
- N O
(5) This page only appears if system encryption is available. Use the cursor/value knobs to tell the C-5000 if it should use side-tones. Press the MODE button to display the next menu page. Publication No. 150-041102 Rev E Page 26 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual S E T U P :
C - 5 0 0 0 D E E M P H 2 = N E X T 3 = B A C K
- N O
(6) This page only appears if system encryption is available. Use the cursor/value knobs to tell the C-5000 if it should use de-emphasis. Press the MODE button to display the next menu page. H O M E = E X I T M I S C S E T U P 2 = R E V I E W
(7) Press the HOME button to exit the miscellaneous configuration menu pages, or the MODE button to review current settings. F. Configuring the C-5000 Using a PC Cobham highly recommends using the PC based Remote Programmer (RP) software to specify the C-5000s configuration. The Remote Programmer software offers several advantages over using theC-5000s front panel which includes:
(1) Allowing you to specify a C-5000s configuration in less time.
(2) Enhanced error checking reduces the likelihood of specifying an incorrect configuration.
(3) A configuration can be specified once and loaded to multiple C-5000s, saving huge amounts of data entry time.
(4) Configurations can be saved, archived, and backed-up, reducing the likelihood of lost data.
(5) Configurations can be uploaded from the C-5000s as well, saving data entry time on existing configurations. Refer to the Remote Programmer softwares user manual 150-041374 for details on how to specify C-
5000 configurations in RpWin. G. Downloading a Configuration from RP into the C-5000 The C-5000 continuously polls the data port on the front panel for incoming data, so all the user has to do is initiate the download from RpWin. Refer to RpWins user manual for details on how to initiate a download. Once the communication channel is open, the C-5000s display will change to the following:
M E M O RY R E C E I V I NG BL O CK=
T RANS F E R 0 0 0 Publication No. 150-041102 Rev E Page 27 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual The 3-digit hexadecimal number to the right of the display on the lower line will increment from 000 to 2FF while the download is in progress. When the download is complete, the C-5000 will automatically restart. H. Uploading a Configuration from the C-5000 into RpWin The C-5000s current configuration can be uploaded into the RpWin software as follows:
(1) From the HOME page, press the PROG button, and enter the appropriate password.
(2) Press the MODE button until the following display page appears:
P R O G :
< E N T E R > = R P L O A D 3 = B A C K 2 = N E X T
(3) Press the ENTER button to display the following page:
M E M O RY S T A R T T RANS F E R S E N D I N G
(4) Ensure the serial cable is connected to both the PC and the C-5000. Ensure the RpWin software is ready to receive data. Refer to RpWins user manual for details on how to prepare RpWin to receive data. Press the LOWER SOFT button on the C-5000 to initiate the transfer. Once the communication channel is open, the C-5000s display will change to the following:
M E M O RY S E N D I NG BL O CK=
T RANS F E R 0 0 0
(5) The 3-digit hexadecimal number to the right of the display on the lower line will increment from 000 to 2FF while the upload is in progress. When the upload is complete, the C-5000s display will return to the following:
P R O G :
< E N T E R > = R P L O A D 3 = B A C K 2 = N E X T
(6) Press the HOME button to return to the HOME PAGE. Note: You will most likely want to save the uploaded data to a disk file on the PC. Refer to RpWins user manual (150-041374) for details on how to do this. Publication No. 150-041102 Rev E Page 28 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual I. Entering CPS Load Mode Digital RT-5000s must have the ITM(s) loaded with Motorola CPS before being able to TX/RX on digital channels. Enter into CPS Load Mode by doing the following:
(1) From the HOME page, press the PROG button, and enter the appropriate password.
(2) Press the MODE button until the following display page appears:
P R O G :
< E N T E R > = C P S L O A D 3 = B A C K 2 = N E X T
(3) Press ENTER button to enter the CPS LOAD screen:
S T A R T R A D I O = 1 C P S L O A D I T M = V H F 1 3 8
(4) Use the cursor to select either Radio 1 or 2 (if available), and between VHF or UHF ITM depending on RT-5000 model number:
S T A R T R A D I O = 1 C P S L O A D I T M = U H F 8 0 0
(5) Press START to open the CPS data lines and communicate between the laptop and the RT-
5000. When finished press END, and HOME twice to return:
E N D R A D I O # 1 C P S L O A D I N C P S M O D E J. KVL Load In order to load encryption keys using a KVL data loader, you must enter KVL LOAD MODE by performing the following procedures:
(1) From the HOME page, press the PROG button, and enter the appropriate password.
(2) Press the MODE button until the following display page appears:
Publication No. 150-041102 Rev E Page 29 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual P R O G :
< E N T E R > = K V L L O A D 3 = B A C K 2 = N E X T
(3) Press ENTER button to enter the KVL LOAD screen:
S T A R T R A D I O = 1 K V L L O A D I T M = V H F 1 3 8
(4) Use the cursor to select either Radio 1 or 2 (if available), and between VHF or UHF ITM depending on RT-5000 model number:
S T A R T R A D I O = 1 K V L L O A D I T M = U H F 8 0 0
(5) Press START to open the KVL data lines and load the encryption keys into the RT-5000. When finished press END, and HOME twice to return:
E N D R A D I O # 1 K V L L O A D I N K V L M O D E NOTE: Unit power must be cycled BEFORE utilizing the radio for communications after performing a key load. K. KEY Erase In order to erase loaded encryption keys, you must enter KEY ERASE MODE by performing the following procedures:
(1) From the HOME page, press the PROG button, and enter the appropriate password.
(2) Press the MODE button until the following display page appears:
Publication No. 150-041102 Rev E Page 30 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual P R O G :
< E N T E R > = K E Y E R A S E 3 = B A C K 2 = N E X T
(3) Press ENTER button to enter the KEY ERASE screen:
S T A R T R A D I O = 1 KE Y E RAS E I T M = V H F 1 3 8
(4) Use the cursor to select either Radio 1 or 2 (if available), and between VHF or UHF ITM depending on RT-5000 model number:
S T A R T R A D I O = 1 KE Y E RAS E I T M = U H F 8 0 0
(5) Press START to erase the encryption keys. When finished press END, and HOME twice to return:
E N D R A D I O # 1 K E Y S E R A S E D KE Y E RAS E 6. CPS Software Description and Programming A. Before You Begin To program the ITM(s) inside the RT-5000 the user must use a Windows based PC and Motorolas CPS software. Users must obtain their own copies of the software from Motorola as Cobham cannot supply it. The programming of the ITM requires three basic steps. First, enter the information that has to do with the setup of the way the RT-5000 communicates with the ITM. Second enter channel information, or what Motorola calls Personalities, and finally assign the personalities to Zones and Channels. It may help tremendously to enlist the help of an experienced CPS programmer. Note: Do Not simply write a portable file into the RT-5000 because this will overwrite data that should not be altered. If your agency uses Motorola XTS-X000 model handhelds, the simplest way to get started is to use an archive from a known properly programmed XTS-X000. Then transfer a single channel to the Publication No. 150-041102 Rev E Page 31 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual resident archive stored in the RT-5000 ITM from the factory. Add more channels once the first one is proven. Alternatively, the ITM comes from the factory with all the necessary information loaded in it for basic operation. The user only needs to load system information such as USER IDs, personalities, and zone/channel allocation. Once an archive for an ITM is established, it can be cloned to other ITMs in other RT-5000s of the same flavor. The CPS software only allows the programmer to see and change functions that are available with the hardware it is trying to program. As such, not all of the screens listed will be seen for every model of ITM. There are (2) versions of CPS that may apply to the RT-5000 depending upon P/N as follows:
RT-5000 P/N 400-015525-0611 through -3511 uses CPS for XTS-3000 Portable radios. CPS P/N RVN4182, which is 1 portion of a 2 disk set ordered under P/N RVN4184. Note: There is no need for a RIB (Radio Interface Box) when using the RT-5000. The RIB is already built into the radio. RT-5000 P/N 400-015525-5011 and above uses CPS for XTS-5000 Portable Radios. CPS P/N RVN4181, which is 1 portion of a 2 disk set ordered under P/N RVN4186. Motorola CPS Ordering Information:
North American Customers: 1-800-422-4210 U.S.A. Federal Customers: 1-800-826-1913 International Customers:
1-847-538-8023 B. CPS Code PMA File Details For a detailed description and help understanding CPS and the numerous options within you may refer to the built in CPS help tool and tutorials. Further definition of each entry may be obtained by pressing F1 with the entry highlighted on the screen. Note: The following is a general guideline for programming the RT-5000 ITMs using the CPS software. Not all of the RT-5000 flavors will follow the same settings as outlined in this manual due to various setting requirements for each specific flavor. Please remember to never modify the Controls and Display and Menu Options unless instructed to do so, as they are set at the factory per the RT-5000 flavor requirement. 7. Radio Information Contains key elements describing the configuration of the module. Publication No. 150-041102 Rev E Page 32 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual A. General This menu contains the model number, serial number, FLASHcode version, and an assignable codeplug alias. B. Tracking Allows you to view information regarding the last programmed date, time, and source of CPS and FLASHport. C. Versioning Allows you to view the latest software versions applied to the codeplug and ITM. D. Feature Set Allows you to view the feature set that is installed in the ITM. Publication No. 150-041102 Rev E Page 33 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 8. Radio Configuration Menu contains elements that affect the overall operation of the radio. A. Radio Wide These menus allow you to modify settings that affect the overall operation of the radio. Note: These are necessary to allow integration of the ITM with the C-5000/RT-5000 system.
(1) General This menu contains general elements of the ITM. Publication No. 150-041102 Rev E Page 34 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Note: DO NOT change any of these settings from the defaults.
(2) Emergency This menu is for setting up the emergency features of the ITM. Publication No. 150-041102 Rev E Page 35 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(3) TPS This menu allows you to modify Tactical Public Safety (TPS) elements.
(4) Alert Tones This menu allows you to modify alert tone elements radio wide. Publication No. 150-041102 Rev E Page 36 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(5) Time-Out Timers This menu allows you to modify port timing elements. Publication No. 150-041102 Rev E Page 37 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(6) Home Mode This menu allows you to change Home Mode elements radio wide. Note: DO NOT enable this option.
(7) Advanced II This menu allows you to change advanced elements radio wide. Publication No. 150-041102 Rev E Page 38 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(8) RX Audio Control This menu allows you to change received audio control elements radio wide.
(9) Surveillance Mode This menu allows you to change Surveillance Mode elements. Publication No. 150-041102 Rev E Page 39 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(10) Data This menu allows you to modify the Radio Wide Data used for the Trunking Systems.
(11) TX Audio Control Per Mode This menu allows you to chance transmit audio control elements radio wide. Publication No. 150-041102 Rev E Page 40 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(12) Digital Audio Options This menu allows you to enable the feedback indication of the received audio quality. d - These are necessary to allow integration of the ITM with the RT-5000 system.
(13) Advance Publication No. 150-041102 Rev E Page 41 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual B. NAT List This allows you to configure the Network Address Translation. C. Controls This contains the Display and Menu options. Settings should be as follows:
(1) Buttons These are set at the factory level and should remain as follows:
Publication No. 150-041102 Rev E Page 42 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
.
(2) Hand Held Control Head - ALL entries should remain set to UNPROGRAMMED.
(3) Switches Settings should be as follows:
Publication No. 150-041102 Rev E Page 43 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual D. Display and Menu
(1) General This menu allows you to modify basic elements of the radios display. Here you can also change the zone and channel text size.
(2) Menu Items - This menu sets up some very critical items in order for the RT-5000 to communicate with the ITM. Publication No. 150-041102 Rev E Page 44 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
****VERY IMPORTANT****: THESE SETTINGS MUST BE EXACTLY AS SHOWN !!!!!
For ITMs with encryption set up as follows:
Conv Item ZONE CHAN MUTE KEY ERAS REKY DIR DIR DIR Trunk Item ZONE CHAN MUTE For ITMs without encryption set up as follows:
Conv Item ZONE CHAN MUTE Trunk Item ZONE CHAN MUTE
(3) Radio Lock This menu allows you to modify the radios security elements. DIR DIR DIR DIR DIR Publication No. 150-041102 Rev E Page 45 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(4) Advanced This menu allows you to modify the radios display elements. E. Phone Contains menus to configure the system to use DTMF codes. Publication No. 150-041102 Rev E Page 46 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(1) Phone Configuration This menu allows you to modify the radios Phone configuration settings applied to Conventional and Trunking personalities.
(2) DTMF Codes This menu allows you to configure the codes used by the radio when utilizing
(3) Phone Number This menu allows you to select the DTMF number for the Phone Number a Phone System. used by the radio. F. Secure The settings in these menus control the overall behavior of the radio when operating in the secure mode. Note: Some of these settings will vary depending on the encryption system. Settings should be as follows:
(1) Secure Configuration Contains menus to modify secure TX and RX elements.
(a) General This menu allows you to modify the General options that apply to the Secure Configuration.
(b) ASTRO OTAR This page controls all ASTRO (Digital) specific OTAR settings. Publication No. 150-041102 Rev E Page 47 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(c) MDC OTAR This page controls all radio settings specifically applicable to MDC
(Analog) OTAR operations.
(d) Multikey Options This screen controls the number of User Selectable Encryption Keys, the CKR (Common Key Reference) and Key Names. Publication No. 150-041102 Rev E Page 48 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(e) Multikey This page controls additional items necessary for the OTAR and secure functions to operate properly. These are necessary to allow integration of the ITM module with the RT-5000 Flexcomm system. DO NOT make changes to these unless instructed.
(f) Advanced This menu allows you to modify the Advanced options that apply to the Secure Configuration. Publication No. 150-041102 Rev E Page 49 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(2) Secure Multikey List This allows you to modify multiply encryption keys for Secure communication.
(3) Secure KMF Profile This menu allows you to modify the Secure Key Managements elements.
(a) ASTRO OTAR Information This menu allows you to modify ASTRO and OTAR elements.
(b) Data Transport This menu allows you to modify elements used in sending Key Management Messages. Publication No. 150-041102 Rev E Page 50 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(c) Secure Hardware Encryption Key Reference List Allows you to modify the set of Common Key References (CKR) the Key Management Facility (KMF) can attain. 9. Conventional - All the aspects of any given channel are assigned to a personality numbered 1 through 255. These menus allow the user to modify the settings for the Conventional Personalities. A. Conventional Configuration These menus are used to configure the conventional personalities.
(1) General This menu allows general configuration of Conventional elements.
(2) Smart PTT This menu allows you to modify Push ToTalk elements of the Conventional channels. Publication No. 150-041102 Rev E Page 51 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual B. MPL Allows you to configure the Multiple Private Line setting.
(1) MPL Configuration This menu allows you to modify the General MPL configuration settings.
(2) MPL List This menu allows you to select a MPL from the current available MPL entries. Note: DO NOT enable this option. C. Conventional Personality Contains the assigned personalities and the configurations for each.
(1) RX Options This menu allows you to modify the Conventional Personalitys RX settings. The Receive Only Box allows the user to make the personality a Receive Only Personality. Publication No. 150-041102 Rev E Page 52 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual This box is normally DISABLED. The user may also designate the RX Voice/Signal Type as either ASTRO, Non-ASTRO, or Mixed Mode which will allow you to RX in both ASTRO and Non-ASTRO mode. Utilize the Squelch (Fine Tune) to adjust the squelch level.
(2) TX Options This menu allows you to modify the Conventional Personalitys TX settings. The user may define the TX Voice/Signal Type as ASTRO or Non-ASTRO only if the RX Voice/Signal Type was selected as Mixed Mode. The user may also select the Transmit Power Level as either High or Low. Publication No. 150-041102 Rev E Page 53 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(3) Signaling - This menu allows you to modify the Conventional Personalitys Signaling System. The Signaling Type may be None, MDC, Quick-Call II, or DTMF.
(4) MDC This menu controls Selective Calling and Paging features of the radio, along with control of the transmit function when other signals are present on the frequency. Please note these options are only available if MDC is selected as the Signaling Type in the Signaling menu. Leave all settings as shown below:
Publication No. 150-041102 Rev E Page 54 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(5) Secure This menu allow you to modify the Conventional Personalitys Secure options. The user may select Clear or Secure in the Secure/Clear Strapping option and may select either DES-XL, OTAR, or ASTRO OTAR.
(6) Secure II This menu allows you to modify the Conventional Personalitys secure TX and encoded RX operations. The user may select a key in the Voice Key Selection as well as select Strapped in the Key Strapping option.
(7) RAC This menu allows you to modify the Conventional Personalitys Repeater Access.
(8) Phone This menu allow you to modify the Conventional Personalitys Phone code to use the radio with a Phone System.
(9) Smart PTT This feature is not enabled Leave set to DISABLED.
(10) Scan This menu allows you to assign the Conventional Personalities to a Scan List. For Vote scan operations users must select a valid scan list and ENABLE Automatic Scan. Note: The Vote Scan feature is not available in all RT-5000 models. Publication No. 150-041102 Rev E Page 55 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(11) Advanced This menu allows you to modify complex features of the Conventional Personality. These options are left DISABLED.
(12) ASTRO This menu allows you to modify the Conventional Personalitys ASTRO
(13) ASTRO Call This menu allows you to modify the Conventional Personalitys ASTRO parameters. System functions.
(14) ASTRO Talkgroup Options This menu allows you to modify the Conventional Personalitys ASTRO System Talkgroup List functions.
(15) Quick-Call II This menu allows you to modify the Call Alert and Selective Call parameters for the Conventional Personality.
(16) DTMF This menu allows you to modify the Call Alert tones for the Conventional Personality. D. Message Alias List This is used to configure various short messages to send via the radio. This feature is currently not used in the FLEXCOMM System. Publication No. 150-041102 Rev E Page 56 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual E. Status Alias List This is used to configure various short status messages to send via the radio. This feature is currently not used in the FLEXCOMM System. F. MDC This is used to configure the MDC operations of the radio.
(1) MDC Call List - This allows you to modify MDC call list menus.
(2) MDC Repeater ID List This allows you to modify IDs for repeaters.
(3) MDC System This menu controls the setup for MDC (Analog) operations. With the exception of the Primary ID, the settings shown on this screen must remain as depicted. The Primary ID is the Unique ID (UID) assigned to the radio, by radio serial number, when it is first established in the radio network. No two radios may have the same UID.
(a) General - This menu allows the user to modify the General MDC system settings.
(b) DOS This menu allows the user to modify the DOS settings for the MDC System. Publication No. 150-041102 Rev E Page 57 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(c) Emergency Revert Allows the user to select a preset used to TX data in Emergency Mode for the Conventional Personality. This menu is only available when Emergency Enable is ENABLED in the Emergency Menu.
(d) Emergency Allows the user to enable the Emergency Enable for the Conventional Personality. Normally set to DISABLED.
(e) Repeater Access Allows the user to enable Repeater function for the Conventional Personality. Pretime (ms): 200
(f) TX Multiplier Allows the user to modify Emergency Mode key-up limits for the Conventional Personality.
(g) Advanced Allows the user to modify Advanced settings for the Conventional Personality. Publication No. 150-041102 Rev E Page 58 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual G. Quick-Call II This is used to configure the Quick-Call II call alert and selective call for each personality.
(1) Quick-Call II Call List This allows you to select which Quick-Call II Call List to be used for the Conventional Personalities.
(2) Quick-Call II System These menus allow you to modify the settings for the Quick-Call II System.
(a) General This menu allows you to modify the General settings of the Quick-Call II System. Publication No. 150-041102 Rev E Page 59 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(b) Advanced - This menu allows you to modify the Advanced settings of the Quick-Call II System. Publication No. 150-041102 Rev E Page 60 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual H. DTMF This is used to configure the DTMF (Dual Tone Multiple Frequency) options.
(1) DTMF Call List This allows you to select which DTMF Call List to be used for the Conventional personalities.
(2) DTMF System These menus allow you to modify the settings for the DTMF System.
(a) General This menu allows you to modify the General settings of the DTMF System. Publication No. 150-041102 Rev E Page 61 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(b) Advanced This menu allows you to modify the Advanced settings of the DTMF System. I. Singletone This is used to configure the Singletone frequency options. Publication No. 150-041102 Rev E Page 62 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(1) Singletone Frequency List This allows you to select which Singletone Frequency is to be used for the Conventional Personality repeater access. This is only available when the Repeater Access Type is set to Singletone in the Conventional Personalities.
(2) Singletone System These menus allow you to modify the settings for the Singletone System. PTT Sidetone:
RAB Sidetone:
Tone Pretime (ms):
Tone Duration (ms):
ENABLED ENABLED 250 500 J. ASTRO Systems This is used to configure the ASTRO system options for each personality.
(1) ASTRO Configuration These menus allows the user to configure all aspects of ASTRO operations for the radio.
(a) Radio Wide This menu allows you to configure the Radio Wide ASTRO System features:
Max TX Attempts:
4 Response Timer:
3300 Min Response Timer: 700 Max Packet Size:
512
( b) Data This menu allows you to modify the Data settings used for the ASTRO System.
(c) Group ID This menu allows you to select the CAI (Common Air Interface) Group ID Frame Sync Seek Period:
TX Short Random Range:
TX Long Random Range:
TX Resp Random Range:
TX Limited Patience:
750 50 2000 1000 Infinite number used for the ASTRO Systems. NUM GROUP ID
(d) OTAC This menu allows you to modify the OTAC (Over-The-Air-Channel) functions that 10000000 10000000 10000000 10000000 10000000 10000000 10000000 10000000 1 2 3 4 5 6 7 8 apply to all ASTRO Systems. OTACS Feature:
OTACR Feature:
DISABLED DISABLED
(e) OTAC Table This menu allows you to modify the OTAC Table and assign the Zones and Channels that utilize OTAC. Publication No. 150-041102 Rev E Page 63 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(f) Soft ID This menu allows you to modify the Soft ID feature used whenever the PTT button is pressed. Soft ID Feature: ENABLED
(2) ASTRO System These menus allow the user to modify the settings for ASTRO Digital operations. All of the settings should remain as depicted EXCEPT the Individual ID. This is the ASTRO ID assigned to the radio by serial number when it is first brought on line in the radio network. It must be unique to the radio.
(a) General - This menu allows you to modify the General settings of the ASTRO System.
(b) Emergency This menu allows you to modify the Emergency settings of the ASTRO System. Emergency:
Emergency Type:
Acknowledge Alert Tone:
NUM REVERT ZONE 1 2 3 1 1 1 DISABLED Alarm Only Enabled REVERT CHANNEL 1 1 1
(c) Emergency Options This menu allows you to modify the Emergency Options for the ASTRO System. Priority TX Inhibit:
DISABLED Publication No. 150-041102 Rev E Page 64 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Limited Patience Time (sec):
Polite Retries:
Impolite Retries:
TX Multiplier:
Silent Override w/Mon:
Global TX Multiplier:
(d) Advanced This menu allows you to modify the Advanced settings for the ASTRO 0 5 15 0 DISABLED DISABLED System. settings.
(e) ARS This menu allows you to modify the ARS (Automatic Registration Service) Automatic Registration Service Enable: DISABLED
(f) DVRS This menu allows you to modify the DVRS (Digital Vehicular Repeater System) settings. DVRS Operation Enable: DISABLED
(3) ASTRO Call List This menu configures group and selective calling features. It is not implemented and therefore should remain blank.
(4) ASTRO Talkgroups List This entire menu is used to configure Conventional ASTRO mode talkgroups, much like trunking. This feature is not supported at this time and therefore this menu should remain empty. Any data shown on the menu is the factory default and may remain. 10. Trunking These menus contain elements that affect the configuration of the trunking system. Publication No. 150-041102 Rev E Page 65 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual A. Trunking Configuration This is used to configure the trunking system and all trunking personalities.
(1) General This menu allows you to modify the General options that apply to Trunking Personalities.
(2) Common Air Interference This menu allows you to change elements of the data sent utilizing the CAI protocol. Publication No. 150-041102 Rev E Page 66 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(3) SMARTZone This menu allows you to modify elements of the SMARTZone functions that can be utilized for all Trunking Personalities. Note: Older Archive CPS files contained Display Site Trunking ENABLED. However this must be DISABLED in order to function properly with customer trunking systems.
(4) RSSI Thersholds This menu allows you to modify elements of the Received Signal Strength Indication (RSSI) utilized for all Trunking Personalities. Publication No. 150-041102 Rev E Page 67 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(5) Filter Constants This menu allows you to modify Filter Constants used in conjunction with the RSSI Thresholds that can be applied to all Trunking Personalities.
(6) Phone This menu allows you to modify the Trunking Personalitys Phone Interconnect for land-to-portable calls. B. Trunking System This is used to set-up the advanced options of the trunking system.
(1) ASTRO 25 Omnilink This menu allows you to modify the Omnilink settings for ASTRO 25 mode. Publication No. 150-041102 Rev E Page 68 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(a) General This menu allows you to modify the General settings of the Trunking System.
(b) Type II This menu allows you to modify the Type II Trunking Setting when Type II is selected in the General menu.
(c) DTMF- This menu allows you to modify the DTMF settings for the Trunking System.
(d) Aliasing This menu allows you to modify the Aliasing setting for the Trunking System.
(e) Message Alias This menu allows you to modify the Message Aliasing settings for the Trunking System. Trunking System.
(f) Status Alias This menu allows you to modify the Status Aliasing settings for the
(g) Site Alias This menu allows you to modify the Site Aliasing settings for the Trunking System. Note: These fields should be set to DISABLED.
(h) Advanced This menu allows you to modify the Advanced settings for the Trunking System. Publication No. 150-041102 Rev E Page 69 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(i) ASTRO 25 Channel ID - This menu allows you to view the Channel ID settings for the Trunking System.
(j) 700_800 ASTRO Control Channels This menu allows you to modify the Control Channel settings for the ASTRO 25 mode.
(k) Data This menu allows you to modify the Data Settings for the Trunking System.
(l) ASTRO 25 Omnilink This menu allows you to modify the Omnilink settings for ASTRO
(m) ASTRO 25 Site Alias This menu allows you to modify the Site Alias settings for the
(n) 700_800 Control Channels This menu allows you to modify the Control Channel 25 mode. ASTRO 25 mode. settings. Publication No. 150-041102 Rev E Page 70 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(o) Dynamic Regrouping This menu allows you to modify the Dynamic Regrouping settings. Enable Dynamic Regrouping: DISABLED
(p) ASTRO 25 This menu allows you to modify the ASTRO 25 settings for the Trunking System.
(q) Digital This menu allows you to modify the Digital settings used for digital communications. Publication No. 150-041102 Rev E Page 71 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(r) Multikey- This menu allows you to assign Multikey fuctions. C. Trunking Personality This is used to set-up individual trunking personalities, as well as select Type II or ASTRO 25 Trunking.
(1) General This menu allows you to modify the General settings of the Trunking Personality. Publication No. 150-041102 Rev E Page 72 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(2) Emergency - This menu allows you to modify the Emergency settings of the Trunking Personality. Publication No. 150-041102 Rev E Page 73 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(3) Secure This menu allows you to modify the Secure settings of the Trunking personality.
(4) Scan This menu allows you to modify the Scan features of the Trunking Personality. Please note that Scan is not currently available in the FLEXCOMM II System. Scan List Selection: None
(5) Phone This menu allows you to modify the Phone settings for the Trunking Personality.
(6) 700/800 Failsoft This menu allows you to modify the 700/800 Failsoft settings for the Phone Interconnect: DISABLED Trunking Personality.
(7) Advanced This menu allows you to modify the Advanced settings for the Trunking Personality. Publication No. 150-041102 Rev E Page 74 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(8) Talkgroup This menu allows you to select the Talkgroup for the Trunking Personality.
(9) Call/Page This menu allows you to select the Call and Page Operation for the Trunking Personality. Publication No. 150-041102 Rev E Page 75 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual
(10) Preferred Sites This menu allows you to select the Preferred Sites for the Trunking Personality.
(11) Emergency Revert This menu allows you to modify and select the Emergency Revert function for the Trunking Personality. D. Trunking Call List This is used to create trunking call lists. E. Type II Trunking Call List This is used as an advanced feature of the trunking system which allows talkgroups to be set-up as trunking channels. 11. Scan These menus contain elements that affect the scan mode. This feature is currently not used in the FLEXCOMM System. Publication No. 150-041102 Rev E Page 76 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual 12. Zone Channel Assignment These menus are used to assign any of the possible 255 Personalities to a specific zone and channel, as well as enter the TX and RX frequencies, and assign the Personality Type as either Conventional (Cnv) or Trunking (Trk). Please follow the CPS programming notes outlined in Section 3 of this manual. Publication No. 150-041102 Rev E Page 77 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual This page intentionally left blank. Appendix A CTCSS (PL) Tone Codes Publication No. 150-041102 Rev E Page 78 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual C-5000 TONE CODE TONE FREQ (HZ) EIA TONE CODE C-5000 TONE CODE TONE FREQ (HZ) EIA TONE CODE 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 67.0 71.9 74.4 77.0 79.7 82.5 85.4 88.5 N/A N/A 91.5 94.8 97.4 100.0 103.5 107.2 110.9 114.8 N/A N/A 118.8 123.0 127.3 131.8 136.5 141.3 146.2 151.4 N/A N/A 156.7 162.2 167.9 173.8 XZ XA WA XB SP YZ YA YB N/A N/A ZZ ZA ZB 1Z 1A 1B 2Z 2A N/A N/A 2B 3Z 3A 3B 4Z 4A 4B 5Z N/A N/A 5A 5B 6Z 6A 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 179.9 186.2 192.8 203.5 N/A N/A 210.7 218.1 225.7 233.6 241.8 250.3 229.1 150.0 N/A N/A 69.3 159.8 165.5 171.3 177.3 183.5 189.9 196.6 N/A N/A 199.5 206.5 254.1 Reserved Reserved Reserved Reserved Reserved 6B 7Z 7A M1 N/A N/A M2 M3 M4 M5 M6 M7 9Z N/A N/A WZ N/A N/A 8Z 0Z Publication No. 150-041102 Rev E Page 79 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual This page intentionally left blank. Publication No. 150-041102 Rev E Page 80 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Overview Appendix B Mode 2 Operation The C-5000 has the capability to control the RT-5000 in such a way that the user can monitor both the main and the Guard (ITM) channel at the same time. This mode of operation is more difficult to use than MODE 1. The Home Page The only visible difference in the HOME PAGE from Mode 1 operation is in the Main/Guard status fields. The illustration below depicts the HOME PAGE for a system comprised of two digital RT-5000 radios. Both radios are configured to operate in Mode 2. The Main transceiver is the active transceiver on radio 1. The digital transceiver (Guard) is the active transceiver on radio 2. The active transceiver is the one that will transmit when the push-to-talk switch is depressed. Main Status Indicators Guard Status Indicators 1 1 2 2 1 2 3 L UKE AF B T W R 1
. 1 T A C T I C A L - 0 0 1
. Main/Guard Status Fields These fields display symbols indicating the current status of all the available transceivers in the system. The symbols are as follows. Indicates a radio is available, but not enabled. Indicates a radio is transmitting. 1 Indicates Main/Guard 1 is available and enabled, but not active. 2 Indicates Main/Guard 2 is available and enabled, but not active. 1 Indicates Main/Guard 1 is available, enabled, and active. 2 Indicates Main/Guard 2 is available, enabled, and active. 1 Indicates Main/Guard 1 is receiving. 2 Indicates Main/Guard 2 is receiving. Publication No. 150-041102 Rev E Page 81 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Setting the Active Transceiver You can toggle the active transceiver for a radio between Main and Guard by pressing the soft keys. The UPPER SOFT KEY toggles the active transceiver for radio 1. The LOWER SOFT KEY toggles the active transceiver for radio 2. The following sequence of illustrations demonstrates this process for radio 1. The Main transceiver is currently active. 1 2 3 L UKE AF B T W R 1
. 1 T A C T I C A L - 0 0 1
. Pressing the UPPER SOFT KEY makes the digital transceiver (Guard) active. 1 5
. T A C T I C A L - 0 1 5
. 1 T A C T I C A L - 0 0 1 Pressing the UPPER SOFT KEY again makes the Main transceiver active. 1 2 3 L UKE AF B T W R 1
. 1 T A C T I C A L - 0 0 1
. 1 1 2 2 1 1 2 2 1 1 2 2 Selecting Preset Channels Selecting preset channels in Mode 2 is conceptually the same as in Mode 1. If an MTM Guard receiver is active, the user can only select preset channels programmed for an ITM, and the main transceiver will only allow you to select channels programmed for a main transceiver. A ramification of this is that you cannot select the manual channel while the Guard receiver is active. Publication No. 150-041102 Rev E Page 82 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Appendix C Single Microphone Operation Overview Starting with software modification 11 (SWID 11), the C-5000 has the ability to control both radios with a single microphone/headset. This feature, hereafter called single-mic mode, is useful for installations where audio panel space is limited, or it is otherwise impractical to dedicate two ports to the C-5000. The main features of single-mic mode are as follows:
Audio from all enabled sources are routed to the primary headset. The operator can dynamically select which transceiver will be used for transmit. Supports both Mode 1 and Mode 2 operation. Configuring Single-Mic Mode You can configure the C-5000s microphone mode using either the Cobham Remote Programmer software or from the C-5000s front panel. To set the option using the Remote Programmer software, simply select Single or Dual from the Mic Mode combo box, located on the Hardware Configuration screen. To set the option from the C-5000s front panel, simply select SINGLE or DUAL from the option list on the MIC MODE configuration page. This page, depicted below, is located under the SETUP MISC. sub-menu of the CFG SYSTEM menu. S E T U P :
2=NEXT MODE M I C 3=B A C K
-S I N G L E The Home Page The main visible difference in single-mic mode is the addition of the active RT indicator, displayed as an unfilled triangle. The active RT indicator shows which RT will be used for transmit. The illustration below depicts the HOME PAGE for a system comprised of two digital RT-5000 radios. Both radios are configured to operate in Mode 2. The Main transceiver of radio 1 is the both the active transceiver for radio 1 and the active RT for the entire system. The digital transceiver (Guard) is the active transceiver on radio 2. Main Status Indicators Guard Status Indicators 1 1 2 3 LUKEAFB 2 2 . 1 TACTICAL- 0 0 1 T W R 1 Publication No. 150-041102 Rev E Page 83 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Setting the Active RT You can change the active RT by pressing the soft keys. If radio 1 does not already contain the active RT, pressing the UPPER SOFT key will make radio 1s active transceiver the active RT. If radio 1 already contains the active RT, pressing the UPPER SOFT key toggles the active RT between radio 1s Main and Guard. The LOWER SOFT key performs the same operations for radio 2. The following sequence of illustrations demonstrates changing the active RT using the soft keys. The Guard transceiver of radio 2 is currently the active RT. Pressing the UPPER SOFT key again makes the Guard transceiver of radio 1 the active RT. Pressing the UPPER SOFT key makes the Main transceiver of radio 1 the active RT. TACTICAL- 0 0 1 1 1 1 2 3 LUKEAFB 2 . 1 1 1 2 3 LUKEAFB 2 2 . 1 TACTICAL- 0 0 1 1 . 1 5 TACTICAL- 0 1 5 TACTICAL- 0 0 1 2 2 . 1 1 1 2 3 LUKEAFB 2 2 . 1 1 1 1 2 3 LUKEAFB 2 . 1 1 1 1 2 3 LUKEAFB 2 . 1 TACTICAL- 0 0 1 TACTICAL- 0 0 1 TACTICAL- 0 0 1 T W R 1 T W R 1 T W R 1 T W R 1 T W R 1 Pressing the LOWER SOFT key makes the Guard transceiver of radio 2 the active RT. Pressing the UPPER SOFT key again makes the Main transceiver of radio 1 the active RT. Pressing the LOWER SOFT key again makes the Main transceiver of radio 2 the active RT. Publication No. 150-041102 Rev E Page 84 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Muting Inactive Receivers The C-5000 can be configured such that the DIM key invokes the MUTE function rather than the DIM function. When MUTE is active, the audio from all non-active transceivers will be muted. Muted transceivers are indicated by an M character in their status fields. See depiction below. 1 5
. T A C T I C A L - 0 1 5
. 1 T A C T I C A L - 0 0 1 M M . You can configure the DIM key for the MUTE function using either the Cobham Remote Programmer software or from the C-5000s front panel. To set the option using the Remote Programmer software, simply select DIM or MUTE from the DIM Key Mode combo box, located on the Hardware Configuration screen. To set the option from the C-5000s front panel, simply select DIM or MUTE from the option list on the DIM KEY MODE configuration page. This page, depicted below, is located under the SETUP MISC. sub-menu of the CFG SYSTEM menu. S E T U P :
D I M K E Y 2=NEXT MODE Publication No. 150-041102 Rev E 3=B A C K
-M UT E Page 85 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual This page intentionally left blank. Publication No. 150-041102 Rev E Page 86 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Appendix D Equivalent Part Numbers Because RT-5000s and C-5000s are maintained as separate products, there can be circumstances when a new flavor (part number) of RT-5000 is released, but the C-5000 is not yet aware of its existence. This problem manifests itself as rejected part numbers in the C-5000 configuration pages for RT-5000 radios. Should this occur, the work around is to enter an RT-5000 part number that will make the C-5000 function properly for the intended radio. As far as the C-5000 is concerned, only the module and encryption types are significant. Should your RT-5000 part number be rejected by the C-5000, find an RT-5000 part number (last 4 digits) in the table that has the equivalent part number to the RT-5000 you are trying to configure. Enter the equivalent part number into the C-5000 configuration pages, and your RT-5000 should function properly. Alternative RT-5000 Part Numbers Standard RT-5000
-0101
-0201
-0301
-0401
-0501
-0611
-0711
-0811
-0911
-1011
-1111
-1211
-1311
-1411
-1511
-1611
-1711
-1811
-1911
-2011
-2111
-2211
-2311
-2411
-2511
-2611
-2711
-2811
-2911
-3011
-3111
-3211
-3311
-3411
-3511
-5011
-5111
-5211
-5311
-0101
-0201
-0301
-0401
-0501
-0611
-0711
-0811
-0911
-1011
-1111
-1211
-1311
-1411
-1511
-1611
-1711
-1811
-1911
-2011
-2111
-2211
-2311
-2411
-2511
-1011
-1211
-0611
-0611
-1211
-1311
-0811
-0611
-2111
-2411
-1611
-2411
-2011
-1211 continues.......... Publication No. 150-041102 Rev E Page 87 of 88 C-5000 Operators Manual FLEXCOMM II C-5000 (P-25 Capable) Operators Manual Appendix D Equivalent Part Numbers (contd)
-5411
-5511
-5611
-5711
-5811
-5911
-6011
-6111
-0811
-1011
-0611
-2611
-0611
-0611
-2411
-6111 Publication No. 150-041102 Rev E Page 88 of 88 C-5000 Operators Manual
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2013-09-20 | 941 ~ 960 | TNB - Licensed Non-Broadcast Station Transmitter | Class II Permissive Change |
2 | 2012-12-28 | 941 ~ 960 | TNB - Licensed Non-Broadcast Station Transmitter | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 2 | Effective |
2013-09-20
|
||||
1 2 |
2012-12-28
|
|||||
1 2 | Applicant's complete, legal business name |
Wulfsberg Electronics Division
|
||||
1 2 | FCC Registration Number (FRN) |
0015514268
|
||||
1 2 | Physical Address |
6400 Wilkinson Drive
|
||||
1 2 |
Prescott, AZ
|
|||||
1 2 |
United States
|
|||||
app s | TCB Information | |||||
1 2 | TCB Application Email Address |
a******@compliancetesting.com
|
||||
1 2 |
k******@compliancetesting.com
|
|||||
1 2 | TCB Scope |
B3: Maritime & Aviation Radio Services equipment in 47 CFR parts 80 & 87
|
||||
1 2 |
B2: General Mobile Radio And Broadcast Services equipment in the following 47 CFR Parts 22 (non-cellular) 73, 74, 90, 95, 97, & 101 (all below 3 GHz)
|
|||||
app s | FCC ID | |||||
1 2 | Grantee Code |
FRW
|
||||
1 2 | Equipment Product Code |
RT-5000P-01
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 2 | Name |
J****** F******** B****
|
||||
1 2 | Title |
Certification Manager
|
||||
1 2 | Telephone Number |
928-7********
|
||||
1 2 | Fax Number |
928-7********
|
||||
1 2 |
j******@cobham.com
|
|||||
app s | Technical Contact | |||||
n/a | ||||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 2 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
1 2 | Yes | |||||
1 2 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 2 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 2 | Equipment Class | TNB - Licensed Non-Broadcast Station Transmitter | ||||
1 2 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | Tactical Airborne Transceiver | ||||
1 2 | 29.7 to 960 MHz Tactical Airborne Transceiver | |||||
1 2 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 2 | Modular Equipment Type | Does not apply | ||||
1 2 | Purpose / Application is for | Class II Permissive Change | ||||
1 2 | Original Equipment | |||||
1 2 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 2 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 2 | Grant Comments | Class II Permissive Change to add Part 80 and Part 87 operation. Power listed is conducted. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of Section 1.1307(b)(3). | ||||
1 2 | Power listed is conducted. RF exposure compliance is addressed at the time of licensing, as required by the responsible FCC Bureau(s), including antenna co-location requirements of Section 1.1307(b)(3). Note 1: 8K10F1E, 8K10F1D, 11K0F3E Note 2: 8K10F1E, 8K10F1D, 11K0F3E, 16K0F3E | |||||
1 2 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 2 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 2 | Firm Name |
Compliance Testing, LLC
|
||||
1 2 | Name |
M******** S********
|
||||
1 2 | Telephone Number |
480-9********
|
||||
1 2 | Fax Number |
480 9********
|
||||
1 2 |
m******@compliancetesting.com
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 87 | 118.05 | 118.05 | 16.41 | 20 ppm | 6K00A3E | ||||||||||||||||||||||||||||||||||
1 | 2 | 87 | 127.5 | 127.5 | 18.24 | 20 ppm | 6K00A3E | ||||||||||||||||||||||||||||||||||
1 | 3 | 87 | 136.95 | 136.95 | 19.01 | 20 ppm | 6K00A3E | ||||||||||||||||||||||||||||||||||
1 | 4 | 87 | 156.3 | 156.3 | 11.8 | 20 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 5 | 87 | 156.3 | 156.3 | 11.8 | 20 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 6 | 87 | 157.425 | 157.425 | 11.75 | 20 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 7 | 87 | 157.425 | 157.425 | 11.75 | 20 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 8 | 8 | 161.775 | 161.775 | 14.62 | 2.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 9 | 8 | 161.775 | 161.775 | 14.62 | 2.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 1 | 8 | 161.775 | 161.775 | 14.62 | 2.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 11 | 9 | 29.7 | 88 | 11.78 | 5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 12 | 9 | 29.7 | 88 | 11.78 | 5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 13 | 9 | 29.7 | 88 | 11.78 | 5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 14 | 9 | 29.7 | 88 | 11.78 | 5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 15 | 22 | 72 | 73 | 11.78 | 5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 16 | 22 | 72 | 73 | 11.78 | 5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 17 | 22 | 72 | 73 | 11.78 | 5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 18 | 22 | 72 | 73 | 11.78 | 5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 19 | 22 | 75.4 | 88 | 11.78 | 5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 2 | 22 | 75.4 | 88 | 11.78 | 5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 21 | 22 | 75.4 | 88 | 11.78 | 5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 22 | 22 | 75.4 | 88 | 11.78 | 5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 23 | 9 | EF | 136 | 150 | 12.42 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 24 | 9 | EF | 136 | 174 | 12.42 | 2.5 ppm | 8K10F1E | |||||||||||||||||||||||||||||||||
1 | 25 | 9 | EF | 136 | 174 | 12.42 | 2.5 ppm | 8K10F1D | |||||||||||||||||||||||||||||||||
1 | 26 | 9 | EF | 136 | 174 | 12.42 | 2.5 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 27 | 9 | EF | 380 | 380 | 19.63 | 2.5 ppm | 6K00A3E | |||||||||||||||||||||||||||||||||
1 | 28 | 9 | EF | 380 | 421 | 10.45 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 29 | 9 | EF | 380 | 520 | 10.45 | 2.5 ppm | 8K10F1E | |||||||||||||||||||||||||||||||||
1 | 3 | 9 | EF | 380 | 520 | 10.45 | 2.5 ppm | 8K10F1D | |||||||||||||||||||||||||||||||||
1 | 31 | 9 | EF | 380 | 520 | 10.45 | 2.5 ppm | 11K0F3E | |||||||||||||||||||||||||||||||||
1 | 32 | 9 | EF | 470 | 520 | 10.45 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
1 | 33 | 9 | 763 | 775 | 8.59 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 34 | 9 | 763 | 775 | 8.5 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 35 | 9 | 763 | 775 | 8.59 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 36 | 9 | 763 | 775 | 8.59 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 37 | 9 | 793 | 805 | 9.64 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 38 | 9 | 793 | 805 | 9.64 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 39 | 9 | 793 | 805 | 9.64 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 4 | 9 | 793 | 805 | 9.64 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 41 | 9 | 806 | 849 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 42 | 9 | 806 | 849 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 43 | 9 | 806 | 849 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 44 | 9 | 806 | 849 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 45 | 22 | 809 | 851 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 46 | 22 | 809 | 851 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 47 | 22 | 809 | 851 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 48 | 22 | 809 | 851 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 49 | 9 | 851 | 894 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 5 | 9 | 851 | 894 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 51 | 9 | 851 | 894 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 52 | 9 | 851 | 894 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 53 | 22 | 854 | 896 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 54 | 22 | 854 | 896 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 55 | 22 | 854 | 896 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 56 | 22 | 854 | 896 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 57 | 9 | 896 | 901 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 58 | 9 | 896 | 901 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 59 | 9 | 896 | 901 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 6 | 9 | 896 | 901 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 61 | 9 | 902 | 930 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 62 | 9 | 902 | 930 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 63 | 9 | 902 | 930 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 64 | 9 | 902 | 930 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 65 | 22 | 928 | 929 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 66 | 22 | 928 | 929 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 67 | 22 | 928 | 929 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 68 | 22 | 928 | 929 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 69 | 22 | 931 | 935 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 7 | 22 | 931 | 935 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 71 | 22 | 931 | 935 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 72 | 22 | 931 | 935 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 73 | 9 | 935 | 940 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 74 | 9 | 935 | 940 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 75 | 9 | 935 | 940 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 76 | 9 | 935 | 940 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
1 | 77 | 22 | 941 | 960 | 11.02 | 1.5 ppm | 8K10F1D | ||||||||||||||||||||||||||||||||||
1 | 78 | 22 | 941 | 960 | 11.02 | 1.5 ppm | 8K10F1E | ||||||||||||||||||||||||||||||||||
1 | 79 | 22 | 941 | 960 | 11.02 | 1.5 ppm | 11K0F3E | ||||||||||||||||||||||||||||||||||
1 | 8 | 22 | 941 | 960 | 11.02 | 1.5 ppm | 16K0F3E | ||||||||||||||||||||||||||||||||||
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
2 | 1 | 9 | 29.7 | 88 | 11.78 | 5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 2 | 22 | 72 | 73 | 11.78 | 5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 3 | 22 | 75.4 | 88 | 11.78 | 5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 4 | 9 | EF | 136 | 150 | 12.42 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
2 | 5 | 9 | EF | 136 | 174 | 12.42 | 2.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
2 | 6 | 9 | EF | 380 | 380 | 19.63 | 2.5 ppm | 6K00A3E | |||||||||||||||||||||||||||||||||
2 | 7 | 9 | EF | 380 | 421 | 10.45 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
2 | 8 | 9 | EF | 380 | 520 | 10.45 | 2.5 ppm | NOTE 1 | |||||||||||||||||||||||||||||||||
2 | 9 | 9 | EF | 470 | 520 | 10.45 | 2.5 ppm | 16K0F3E | |||||||||||||||||||||||||||||||||
2 | 1 | 9 | 763 | 775 | 8.59 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 11 | 9 | 793 | 805 | 9.64 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 12 | 9 | 806 | 849 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 13 | 22 | 809 | 851 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 14 | 9 | 851 | 894 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 15 | 22 | 854 | 896 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 16 | 9 | 896 | 901 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 17 | 9 | 902 | 930 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 18 | 22 | 928 | 929 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 19 | 22 | 931 | 935 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 2 | 9 | 935 | 940 | 11.02 | 1.5 ppm | NOTE 2 | ||||||||||||||||||||||||||||||||||
2 | 21 | 22 | 941 | 960 | 11.02 | 1.5 ppm | NOTE 2 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC