FCC ID: DYDWT3125 Windows-Based Terminal

Winterm Model 3125SE WBT Quick-Start Guide Connect Caution: Improper connection, mounting, or use of this product could result in component failure and/or flash memory corruption. Read the following caution statements before setting up and operating the terminal. Cautions:

Setup Do not connect power until all other connections are made. Connecting or disconnecting components or devices on the back panel when the terminal is receiving power can cause power surges and damage the terminal. (USB ports are hot-swappable.)

Do not force a connector into its socket. If any undue resistance is encountered, ensure that the connector is correctly oriented to the receptacle. Orientation and Venting

Mount the terminal only as shown above. Improper orientation (such as component side down, where the back panels symbols are upside down) could inhibit the dissipation of heat from the terminal and damage it.

Allow sufficient space around the terminal for ventilation; do not place the terminal in any enclosure that restricts airflow around the terminal; do not place any objects on the terminal. Product environmental specifications are available through Wyses Web site at http://www.wyse.com/products/winterm/products.htm. Power Sources

To ensure regulatory compliance, use only the power supply included in the shipping box, or a Wyse-approved equivalent, with the terminal. Also, the noise suppressor (ferrite bead) included in the box with the terminal must be installed on the network cable as described in the accompanying instructions. Refer to the regulatory notices in the terminals on-line documentation at http://www.wyse.com/products/winterm/

quickstart/3000.htm.

To prevent accidental loss of power, brown out, and spikes which could damage the terminal, avoid connecting it to any form of switching device (including power strips) or hard resetting the terminal by holding down the power button.

When turning off the terminal, be sure to perform a complete shutdown (via the user interface or power button); do not disconnect the power cord, shut off power at a circuit breaker, etc., to turn off the terminal.

*Supplied for U.S.A.; in other locales, check package contents or contact your Wyse reseller. Model 3125SE Back Panel Connectors Icon Connector Headphones USB port (3) Video Description Audio output jack for headphones or powered speakers USB device connection Monitor interface Network (LAN) Ethernet RJ45 connection, 10/100Base-T Power Lock Parallel Port Keyboard Mouse Serial Port1 Serial Port1 Power module cable interface Receptacle for cable lock Local printer output PS/2-type keyboard interface PS/2-type mouse interface Serial device connection Serial device connection 1. For a listing of recommended peripherals visit http://www.wyse.com/serviceandsupport/support/winterm/peripherals/3000peripheral.htm. Turn On Wait until the initialization sequence is completed (amber light goes off) before pressing the power button. Important: By unpacking and using the terminal, you agree to be bound by the license agreements in the users and administrators guides. See those agreements for specific details at http://www.wyse.com/products/winterm/quickstart/

3000.htm. Configure Setup is quick and simple... The logo will appear on the screen, followed by:

The Setup Wizard, if it is the first time that you have turned on your terminal.

The Winterm Connection Manager dialog box, if the Setup Wizard has been completed. Help Need more information or upgrades/accessories?

http://www.wyse.com/products/winterm/quickstart/3000.htm Need more information on Wyse Rapport, the remote management software that comes with this terminal, or Wyses automated warranty registration process?

http://www.wyse.com/bundle Register within 90 days to get 2 years extended warranty at no cost. Wyse Technology Inc. 3471 North First Street San Jose, CA 95134-1801 U.S.A. 883752-01 Rev. A July 2002 Printed in U.S.A. 2002 Wyse Technology Inc. All rights reserved.

Winterm 3000 Series Windows:?-based Terminal Administrators Guide issue: 072301 xi FCC Statement This equipment has been tested and found to comply with the limits for either Class A or Class B digital devices (refer to Terminal Requirements Compliance"), pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

* Increase the separation between the equipment and the receiver.

* Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

* Consult the dealer or an experienced radio/TV technician for help. Caution Changes or modifications not covered in this manual must be approved in writing by the manufacturer's Regulatory Engineering department. Changes or modifications made without written approval may void the users authority to operate the equipment. Terminal Requirements Compliance FCC Compliance Models 3200LE, 3230LE, 3320SE, 3350SE, 3360SE, 3630LE, 3730LE, and 3720SE terminals meet Class B requirements. iIEC/EN Compliance Models 3200LE, 3230LE, 3320SE, 3350SE, 3360SE, 3630LE, 3730LE, and 3720SE terminals meet Class B requirements. Canadian DOC Notices Refer to the previous section, Terminal Requirements Compliance, to find out to which model terminal each of the statements below refers. Class A This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le prsent appareil numrique nmet pas de bruits radiolectriques dpassant les limites applicables aux appareils numriques de la classe A prescrites dans le Rglement sur le brouillage radiolectrique dict par le Ministre des Communications du Canada. xii Class B This digital apparatus does not exceed the Class B limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications. Le prsent appareil numrique nmet pas de bruits radiolectriques dpassant les limites applicables aux appareils numriques de la classe B prescrites dans le Rglement sur le brouillage radiolectrique dict par le Ministre des Communications du Canada. IEC/EN Notice This product conforms to the requirements of IEC950 and EN60950. This product conforms to requirements of EN55022 for Class A equipment or EN55022 for Class B equipment (refer to Terminal Requirements Compliance). Models 3320SE, 3350SE, and 3360SE Terminals For use with External Power Supply DVE Model DSA-0301-05 or certified equivalent model supplied by the manufacturer, rated minimum 5V/4A. Models 3200LE and 3230LE Terminals For use with External Power Supply DVE Model DSA-0151D-12 or certified equivalent model supplied by the manufacturer, rated minimum 12V/1.5A. Model 3630LE Terminals For use with External Power Supply Ilan Model F1650K or certified equivalent model supplied by the manufacturer, rated minimum 12 V/3.5A. Noise Suppressor A noise suppressor (ferrite bead) must be installed on the network cable of your terminal. This installation is necessary to maintain compliance with U.S. FCC B limits and European CISPR B EN55022 Class B limits. The noise suppressor is supplied by the manufacturer and is packed in your terminal's shipping carton. Cable Notice The use of shielded I/O cables is required when connecting this equipment to any and all optional peripheral or host devices. Failure to do so may cause interference and violate FCC and international regulations for electromagnetic interference. 55 Noise Suppressor Installation A noise suppressor (ferrite bead) must be installed on the network cable of your terminal. This installation is necessary to maintain compliance with US FCC B limits and European CISPR B EN55022 Class B limits. The noise suppressor is supplied by the manufacturer and is packed in your terminal's shipping carton. Figure 55-1 shows the noise suppressor. Figure 55-1 Noise Suppressor To install:

1. Open the casing. 2. Fit the casing over the network cable, as close as possible to the back of the cables connector. 3. Snap the casing shut.