all | frequencies |
|
|
exhibits | applications |
---|---|---|---|---|---|
manuals |
app s | submitted / available | |||||||
---|---|---|---|---|---|---|---|---|
1 |
|
Users Manual 1 | Users Manual | 2.21 MiB | June 11 2003 | |||
1 |
|
Users Manual 2 | Users Manual | 2.60 MiB | June 11 2003 | |||
1 | Cover Letter(s) | June 11 2003 | ||||||
1 | Operational Description | June 11 2003 | ||||||
1 | Cover Letter(s) | June 11 2003 | ||||||
1 | External Photos | June 11 2003 | ||||||
1 | Internal Photos | June 11 2003 | ||||||
1 | ID Label/Location Info | June 11 2003 | ||||||
1 | ID Label/Location Info | June 11 2003 | ||||||
1 | Cover Letter(s) | June 11 2003 | ||||||
1 | RF Exposure Info | June 11 2003 | ||||||
1 | Test Report | June 11 2003 | ||||||
1 | Test Setup Photos | June 11 2003 |
1 | Users Manual 1 | Users Manual | 2.21 MiB | June 11 2003 |
IEEE 802.11b X-Micro WLAN Broadband Router Users Manual Version 1.2 Trademarks 2003 X-Micro Technology Corp. Contents are subject to change without notice. All trademarks belong to their respective proprietors. Copyright Statement THIS DOCUMENT CONTAINS OF PROPRIETARY TECHNICAL INFORMATION THAT IS THE PROPERTY OF X-
MICRO TECHNOLOGY CORP. AND NO PART OF THIS DOCUMENTATION MAY BE REPRODUCED, STORED IN A RETRIEVAL SYSTEM OR TRANSMITTED IN ANY FORM OR BY ANY MEANS, ELECTRICAL OR MECHANICAL, BY PHOTOCOPYING, RECORDING, OR OTHERWISE, WITHOUT THE PRIOR WRITTEN CONSENT OF X-MICRO TECHNOLOGY CORP. INFORMATION TO USER FCC INFORMATION FCC Radiation Exposure Statement This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. The equipment has been tested and found to comply with the limits for a Class B Digital Device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction, may cause harmful interference to radio communication. However, there is no grantee that interference will not occur in a particular installation. If this equipment dose cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
--Reorient or relocate the receiving antenna.
--Increase the separation between the equipment and receiver.
--Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
--Consult the dealer or an experienced radio/TV technician for help. Notice: The Part 15 radio device operates on a non-interference basis with other devices operating at this frequency. Any changes or modification not expressly approved by the party responsible could void the users authority to operate the device. USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Terminology ANSI AP CCK CSMA/CA CSMA/CD DHCP DSSS FCC FTP IEEE IP ISM LAN MAC NAT NT PSD RF SNR SSID TCP TFTP WEP WLAN American National Standards Institute Access Point Complementary Code Keying Carrier Sense Multiple Access/ Collision Avoidance Carrier Sense Multiple Access/ Collision Detection Dynamic Host Configuration Protocol Direct Sequence Spread Spectrum Federal Communications Commission File Transfer Protocol Institute of Electrical and Electronic Engineers Internet Protocol Industrial, Scientific and Medical Local Area Network Media Access Control Network Address Translation Network Termination Power Spectral Density Radio Frequency Signal to Noise Ratio Service Set Identification Transmission Control Protocol Trivial File Transfer Protocol Wired Equivalent Privacy Wireless Local Area Network iv USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Table of Contents TERMINOLOGY ..........................................................................................................................IV 1 INTRODUCTION.................................................................................................................... 1 1.1 1.2 1.3 1.4 1.5 PACKAGE CONTENTS........................................................................................................... 1 PRODUCT SPECIFICATIONS .................................................................................................. 1 PRODUCT FEATURES ........................................................................................................... 2 FRONT PANEL DESCRIPTION ............................................................................................... 2 REAR PANEL DESCRIPTION ................................................................................................. 3 2 INSTALLATION ..................................................................................................................... 4 2.1 2.2 HARDWARE INSTALLATION ................................................................................................. 4 SOFTWARE INSTALLATION................................................................................................... 4 3 SOFTWARE CONFIGURATION ......................................................................................... 5 PREPARE YOUR PC TO CONFIGURE THE X-MICRO WLAN BROADBAND ROUTER............... 5 3.1 3.2 CONNECT TO THE X-MICRO WLAN BROADBAND ROUTER................................................ 7 3.3 MANAGEMENT AND CONFIGURATION ON THE X-MICRO WLAN BROADBAND ROUTER ..... 7 STATUS............................................................................................................................ 7 3.3.1 3.3.2 WIRELESS BASIC SETTINGS ............................................................................................ 9 WIRELESS ADVANCED SETTINGS .................................................................................. 10 3.3.3 WIRELESS SECURITY SETUP.......................................................................................... 11 3.3.4 3.3.5 WIRELESS ACCESS CONTROL........................................................................................ 13 LAN INTERFACE SETUP................................................................................................ 14 3.3.6 WAN INTERFACE SETUP............................................................................................... 15 3.3.7 3.3.8 FIREWALL - PORT FILTERING......................................................................................... 17 FIREWALL - IP FILTERING ............................................................................................. 18 3.3.9 FIREWALL - MAC FILTERING........................................................................................ 19 3.3.10 3.3.11 FIREWALL - PORT FORWARDING.................................................................................... 20 FIREWALL - DMZ ......................................................................................................... 21 3.3.12 STATISTICS .................................................................................................................... 22 3.3.13 3.3.14 UPGRADE FIRMWARE.................................................................................................... 23 SAVE/ RELOAD SETTINGS ............................................................................................. 24 3.3.15 v USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 3.3.16 PASSWORD SETUP......................................................................................................... 25 4 FREQUENTLY ASKED QUESTIONS (FAQ).................................................................... 27 4.1 WHAT AND HOW TO FIND MY PCS IP AND MAC ADDRESS? ............................................. 27 4.2 WHAT IS WIRELESS LAN? ................................................................................................ 27 4.3 WHAT ARE ISM BANDS? ................................................................................................... 27 4.4 HOW DOES WIRELESS NETWORKING WORK?...................................................................... 27 4.5 WHAT IS BSSID? .............................................................................................................. 28 4.6 WHAT IS ESSID? .............................................................................................................. 28 4.7 WHAT ARE POTENTIAL FACTORS THAT MAY CAUSES INTERFERENCE? ................................ 29 4.8 WHAT ARE THE OPEN SYSTEM AND SHARED KEY AUTHENTICATIONS? ............................. 29 4.9 WHAT IS WEP?................................................................................................................. 29 4.10 WHAT IS FRAGMENT THRESHOLD?.................................................................................... 29 4.11 WHAT IS RTS (REQUEST TO SEND) THRESHOLD?............................................................. 30 4.12 WHAT IS BEACON INTERVAL?............................................................................................ 30 4.13 WHAT IS PREAMBLE TYPE?............................................................................................... 31 4.14 WHAT IS SSID BROADCAST? ............................................................................................ 31 vi USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 1 Introduction The X-Micro Wireless LAN Broadband Router is an affordable IEEE 802.11b wireless LAN broadband router solution, setting SOHO and enterprise standard for high performance, secure, manageable and reliable WLAN. This document describes the steps required for the initial IP address assign and other WLAN router configuration. The description includes the implementation of the above steps. Notice: It will take about 25 seconds to complete the boot up sequence after powered on the X-Micro WLAN Broadband Router; all LEDs are blank while booting except the Power LED, and after that the WLAN Activity LED will be flashing to show the WLAN interface is enabled and working now. 1.1 Package contents The package of the X-Micro WLAN Broadband Router includes the following items,
The X-Micro WLAN Broadband Router
The AC to DC 9V Power Adapter
Users manual CD-ROM 1.2 Product Specifications Product Name Standard Data Transfer Rate Modulation Method Frequency Band RF Output Power Receiver Sensitivity Operation Range Antenna LED Security LAN interface Power Consumption Dimension Operating Temperature Storage Temperature Humidity X-Micro WLAN Broadband Router 801.11b(Wireless), 802.3(10BaseT), 802.3u(100BaseT) 11Mbps(Wireless), 100Mbps(Ethernet) DBPSK/ DQPSK/ CCK 2.4GHz 2.497GJz ISM Band, DSSS
< 17 dBm 11Mbps better than 8% PER @ -88 dBm 30 to 300 meters (depend on surrounding) External Antenna Power, Active (WLAN), Act/Link (Ethernet) 64 bit/ 128 bit WEP, port filtering, IP filtering, MAC filtering, port forwarding and DMZ hosting One 10/100BaseT with RJ45 connector (WAN) Four 10/100BaseT with RJ45 connectors (LAN) DC 9V Power Adapter 160 x 110 x 35 mm 0 50oC ambient temperature
-20 - 70oC ambient temperature 5 to 90 % maximum (non-condensing) 1 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 1.3 Product Features
Complies with IEEE 802.11b standard for 2.4GHz Wireless LAN.
Supports 11Mbps data transfer rate with automatic fallback to 5.5M, 2M and 1Mbps.
Supports bridging, routing functions between wireless and wired Ethernet interfaces.
Supports 64-bit and 128-bit WEP encryption/decryption function to protect the wireless data transmission.
Supports IEEE 802.3x full duplex flow control on 10/100M Ethernet interface.
Supports DHCP server to provide clients auto IP addresses assignment.
Supports DHCP client for Ethernet WAN interface auto IP address assignment.
Supports static and dynamic IP routing.
Supports PPPoE on Ethernet WAN interface.
Supports clone MAC address function.
Supports firewall security with port filtering, IP filtering, MAC filtering, port forwarding, trigger port and DMZ hosting functions.
Supports WEB based management and configuration. 1.4 Front Panel Description Figure 1 X-Micro WLAN Broadband Router Front Panel LED Indicator 1. Power LED 2. WLAN Activity LED 3. WAN ACT LED 4. WAN 10/100M LED 5. LAN ACT LED State On Description The WLAN Broadband Router is powered on. Flashing Flashing Off Off Off On Off Off Flashing The WLAN Broadband Router is powered off. Data is transmitting or receiving on the antenna. No data is transmitting or receiving on the antenna. Data is transmitting or receiving on the WAN interface. No data is transmitting or receiving on the WAN interface. Connection speed is 100Mbps on WAN interface. Connection speed is 10Mbps on WAN interface. Data is transmitting or receiving on the LAN interface. No data is transmitting or receiving on the LAN 2 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 6. LAN 10/100M LED On Off interface. Connection speed is 100Mbps on LAN interface. Connection speed is 10Mbps on LAN interface. 1.5 Rear Panel Description Antenna WAN LAN Power Figure 2 X-Micro WLAN Broadband Router Rear Panel Interfaces 1. WAN 2. LAN 3. Power 4. Antenna Description The RJ-45 socket allows WAN connection through a Category 5 cable. Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively. The RJ-45 sockets allow LAN connection through Category 5 cables. Support auto-sensing on 10/100M speed and half/ full duplex; comply with IEEE 802.3/ 802.3u respectively. The power jack allows an external DC +9 V power supply connection. The external AC to DC adaptor provide adaptive power requirement to the X-Micro WLAN Broadband Router. The Wireless LAN Antenna. 3 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 2 Installation 2.1 Hardware Installation Step One: Place the X-Micro Wireless LAN Broadband Router to the best optimum transmission location. The best transmission location for your X-Micro WLAN Broadband Router is usually at the geographic center of your wireless network, with line of sign to all of your mobile stations. Step Two: Connect the X-Micro WLAN Broadband Router to your wired network. Connect the Ethernet WAN interface of X-Micro WLAN Broadband Router by category 5 Ethernet cable to your switch/ hub/ xDSL modem or cable modem. A straight-through Ethernet cable with appropriate cable length is needed. Step Three: Supply DC power to the X-Micro WLAN Broadband Router. Use only the AC/DC power adapter supplied with the X-Micro WLAN Broadband Router; it may occur damage by using a different type of power adapter. The hardware installation finished. 2.2 Software Installation
There are no software drivers, patches or utilities installation needed, but only the configuration setting. Please refer to chapter 3 for software configuration. 4 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 3 Software configuration There are web based management and configuration functions allowing you to have the jobs done easily. The X-Micro WLAN Broadband Router is delivered with the following factory default parameters on the Ethernet LAN interfaces. Default IP Address: 192.168.1.254 Default IP subnet mask: 255.255.255.0 WEB login User Name: <empty>
WEB login Password: <empty>
3.1 Prepare your PC to configure the X-Micro WLAN Broadband Router For OS of Microsoft Windows 95/ 98/ Me:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. Note: Windows Me users may not see the Network control panel. If so, select View all Control Panel options on the left side of the window 2. Move mouse and double-click the right button on Network icon. The Network window will appear. 3. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. IP Subnet Mask: 255.255.255.0 8. Click OK and reboot your PC after completes the IP parameters setting. For OS of Microsoft Windows 2000, XP:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 5 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 2. Move mouse and double-click the right button on Network and Dial-up Connections icon. Move mouse and double-click the Local Area Connection icon. The Local Area Connection window will appear. Click Properties button in the Local Area Connection window. 3. Check the installed list of Network Components. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. IP Subnet Mask: 255.255.255.0 8. Click OK to completes the IP parameters setting. For OS of Microsoft Windows NT:
1. Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear. 2. Move mouse and double-click the right button on Network icon. The Network window will appear. Click Protocol tab from the Network window. 3. Check the installed list of Network Protocol window. If TCP/IP is not installed, click the Add button to install it; otherwise go to step 6. 4. Select Protocol in the Network Component Type dialog box and click Add button. 5. Select TCP/IP in Microsoft of Select Network Protocol dialog box then click OK button to install the TCP/IP protocol, it may need the Microsoft Windows CD to complete the installation. Close and go back to Network dialog box after the TCP/IP installation. 6. Select TCP/IP and click the properties button on the Network dialog box. 7. Select Specify an IP address and type in values as following example.
IP Address: 192.168.1.1, any IP address within 192.168.1.1 to 192.168.1.253 is good to connect the Wireless LAN Access Point. IP Subnet Mask: 255.255.255.0 8. Click OK to completes the IP parameters setting. 6 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 3.2 Connect to the X-Micro WLAN Broadband Router Open a WEB browser, i.e. Microsoft Internet Explore, then enter 192.168.1.254 on the URL to connect the X-Micro WLAN Broadband Router. 3.3 Management and configuration on the X-Micro WLAN Broadband Router 3.3.1 Status This page shows the current status and some basic settings of the device, includes system, wireless, Ethernet LAN and WAN configuration information. Screenshot Status-1 7 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Status-2 Item System Alias Name Uptime Firmware version Wireless configuration SSID Channel Number WEP Associated Clients BSSID LAN configuration IP Address Subnet Mask Description It shows the alias name of this X-Micro WLAN Broadband Router. It shows the duration since X-Micro WLAN Broadband Router is powered on. It shows the firmware version of X-Micro WLAN Broadband Router. It shows the SSID of this X-Micro WLAN Broadband Router. The SSID is the unique name of X-Micro WLAN Broadband Router and shared among its service area, so all devices attempts to join the same wireless network can identify it. It shows the wireless channel connected currently. It shows the status of WEP encryption function. It shows the number of connected clients (or stations, PCs). It shows the BSSID address of the X-Micro WLAN Broadband Router. BSSID is a six-byte address. It shows the IP address of LAN interfaces of X-Micro WLAN Broadband Router. It shows the IP subnet mask of LAN interfaces of X-
8 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Default Gateway DHCP Server MAC Address WAN configuration Attain IP Protocol IP Address Subnet Mask Default Gateway MAC Address Micro WLAN Broadband Router. It shows the default gateway setting for LAN interfaces outgoing data packets. It shows the DHCP server is enabled or not. It shows the MAC address of LAN interfaces of X-Micro WLAN Broadband Router. It shows how the X-Micro WLAN Broadband Router gets the IP address. The IP address can be set manually to a fixed one or set dynamically by DHCP server or attain IP by PPPoE connection. It shows the IP address of WAN interface of X-Micro WLAN Broadband Router. It shows the IP subnet mask of WAN interface of X-
Micro WLAN Broadband Router. It shows the default gateway setting for WAN interface outgoing data packets. It shows the MAC address of WAN interface of X-Micro WLAN Broadband Router. 3.3.2 Wireless Basic Settings This page is used to configure the parameters for wireless LAN clients that may connect to your Broadband Router. Here you may change wireless encryption settings as well as wireless network parameters. 9 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Wireless Basic Settings Item Alias Name Disable Wireless LAN Interface SSID Channel Number Associated Clients Apply Changes Reset Description It is the alias name of this X-Micro WLAN Broadband Router. The alias name can be 32 characters long. Tick on to disable the wireless LAN data transmission. It is the wireless network name. The SSID can be 32 bytes long. Select the wireless communication channel from pull-
down menu. Click the Show Active Clients button to open Active Wireless Client Table that shows the MAC address, transmit-packet, receive-packet and transmission-rate for each associated wireless client. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 3.3.3 Wireless Advanced Settings These settings are only for more technically advanced users who have a sufficient knowledge about wireless LAN. These settings should not be changed unless you know what effect the changes will have on your X-Micro WLAN Broadband Router. 10 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Wireless Advanced Settings Item Authentication Type Fragment Threshold RTS Threshold Beacon Interval Data Rate Preamble Type Broadcast SSID Apply Changes Reset Description Click to select the authentication type in Open System, Shared Key or Auto selection. Set the data packet fragmentation threshold, value can be written between 256 and 2346 bytes. Refer to 4.10 What is Fragment Threshold?
Set the RTS Threshold, value can be written between 0 and 2347 bytes. Refer to 4.11 What is RTS (Request To Send) Threshold?
Set the Beacon Interval, value can be written between 20 and 1024 ms. Refer to 4.12 What is Beacon Interval?
Select the transmission data rate from pull-down menu. Data rate can be auto-select, 11M, 5.5M, 2M or 1Mbps. Click to select the Long Preamble or Short Preamble support on the wireless data packet transmission. Refer to 4.13 What is Preamble Type?
Click to enable or disable the SSID broadcast function. Refer to 4.14 What is SSID Broadcast?
Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 3.3.4 Wireless Security Setup This page allows you setup the WEP security. Turn on WEP by using encryption keys could prevent any unauthorized access to your wireless network. 11 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Wireless Security Setup Item Enable WEP Security Click the check box to enable WEP security function. Description Key Length Key Format Default Tx Key Encryption Key 1 Encryption Key 2 Encryption Key 3 Encryption Key 4 Apply Changes Reset Refer to 4.9 What is WEP?
Select the WEP shared secret key length from pull-down menu. The length can be chose between 64-bit and 128-
bit (known as WEP2) keys. The WEP key is composed of initialization vector (24 bits) and secret key (40-bit or 104-bit). Select the WEP shared secret key format from pull-down menu. The format can be chose between plant text
(ASCII) and hexadecimal (HEX) code. Set the default secret key for WEP security function. Value can be chose between 1 and 4. Secret key 1 of WEP security encryption function. Secret key 2 of WEP security encryption function. Secret key 3 of WEP security encryption function. Secret key 4 of WEP security encryption function. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. WEP encryption key (secret key) length:
Length Format 64-bit 128-bit 12 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 ASCII HEX 5 characters 13 characters 10 hexadecimal codes 26 hexadecimal codes 3.3.5 Wireless Access Control If you enable wireless access control, only those clients whose wireless MAC addresses are in the access control list will be able to connect to your Access Point. When this option is enabled, no wireless clients will be able to connect if the list contains no entries. Screenshot Wireless Access Control Description MAC Address Item Enable WEP Security Click the check box to enable wireless access control. This is a security control function; only those clients registered in the access control list can link to this X-
Micro WLAN Broadband Router. Fill in the MAC address of client to register this X-Micro WLAN Broadband Router access capability. Fill in the comments for the registered client. Click the Apply Changes button to register the client to new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. It shows the registered clients that are allowed to link to this X-Micro WLAN Broadband Router. Comment Apply Changes Current Access Control List Reset 13 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Delete Selected Delete All Reset Click to delete the selected clients that will be access right removed from this X-Micro WLAN Broadband Router. Click to delete all the registered clients from the access allowed list. Click the Reset button to abort change and recover the previous configuration setting. 3.3.6 LAN Interface Setup This page is used to configure the parameters for local area network that connects to the LAN ports of your X-Micro WLAN Broadband Router. Here you may change the setting for IP address, subnet mask, DHCP, etc. Screenshot LAN Interface Setup Item IP Address Subnet Mask Default Gateway DHCP Server DHCP Client Range Description Fill in the IP address of LAN interfaces of this X-Micro WLAN Broadband Router. Fill in the subnet mask of LAN interfaces of this X-
Micro WLAN Broadband Router. Fill in the default gateway for LAN interfaces out going data packets. Select to enable or disable the DHCP server function on LAN interfaces from pull-down menu. Fill in the start IP address and end IP address to allocate a range of IP addresses; client with DHCP function set will 14
1 | Users Manual 2 | Users Manual | 2.60 MiB | June 11 2003 |
USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 802.11d Spanning Tree Select to enable or disable the IEEE 802.1d Spanning Show Client Clone MAC Address Apply Changes Reset be assign a IP address from the range. Click to open the Active DHCP Client Table window that shows the active clients with their assigned IP address, MAC address and time expired information. Tree function from pull-down menu. Fill in the MAC address that is the MAC address to be cloned. Clone MAC address is designed for your special application that request the clients to register to a server machine with one identified MAC address. Since that all the clients will communicate outside world through the X-Micro WLAN Broadband Router, so have the cloned MAC address set on the X-Micro WLAN Broadband Router will solve the issue. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 3.3.7 WAN Interface Setup This page is used to configure the parameters for wide area network that connects to the WAN port of your X-Micro WLAN Broadband Router. Here you may change the setting for IP address, PPPoE and DNS, etc. Screenshot WAN Interface Setup - 1 15 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot WAN Interface Setup - 2 Item Attain IP Automatically (DHCP) Fixed IP IP Address Subnet Mask Default Gateway PPPoE User Name Password Connection Type Description Click to select DHCP support on WAN interface for IP address assigned automatically from a DHCP server. Click to select fixed IP support on WAN interface. There are IP address, subnet mask and default gateway settings need to be done. If you select the fixed IP support on WAN interface, fill in the IP address for it. If you select the fixed IP support on WAN interface, fill in the subnet mask for it. If you select the fixed IP support on WAN interface, fill in the default gateway for WAN interface out going data packets. Click to select PPPoE support on WAN interface. There are user name, password, connection type and idle time settings need to be done. If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server. If you select the PPPoE support on WAN interface, fill in the user name and password to login the PPPoE server. Select the connection type from pull-down menu. There are Continuous, Connect on Demand and Manual three types to select. Continuous connection type means to setup the 16 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 connection through PPPoE protocol whenever this X-
Micro WLAN Broadband Router is powered on. Connect on Demand connection type means to setup the connection through PPPoE protocol whenever you send the data packets out through the WAN interface; there are a watchdog implemented to close the PPPoE connection while there are no data sent out longer than the idle time set. Manual connection type means to setup the connection through the PPPoE protocol by clicking the Connect button manually, and clicking the Disconnect button manually. If you select the PPPoE and Connect on Demand connection type, fill in the idle time for auto-disconnect function. Value can be between 1 and 1000 minutes. Click to select getting DNS address for DHCP, PPPoE support. Please select Set DNS Manually if the Fixed IP support is selected. Click to select getting DNS address for Fixed IP support. Fill in the IP address of Domain Name Server 1. Fill in the IP address of Domain Name Server 2. Fill in the IP address of Domain Name Server 3. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. Idle Time Attain DNS Automatically Set DNS Manually DNS 1 DNS 2 DNS 3 Apply Changes Reset 3.3.8 Firewall - Port Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. 17 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Firewall - Port Filtering Description Item Enable Port Filtering Click to enable the port filtering security function. Port Range Protocol Comments To restrict data transmission from the local network on certain ports, fill in the range of start-port and end-port, and the protocol, also put your comments on it. The Protocol can be TCP, UDP or Both. Comments let you know about whys to restrict data from the ports. Click the Apply Changes button to register the ports to port filtering list. Click the Reset button to abort change and recover the previous configuration setting. Click to delete the selected port range that will be removed from the port-filtering list. Click to delete all the registered entries from the port-
filtering list. Click the Reset button to abort change and recover the previous configuration setting. Apply Changes Reset Delete Selected Delete All Reset 3.3.9 Firewall - IP Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. 18 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Firewall - IP Filtering Item Enable IP Filtering Local IP Address Protocol Comments Apply Changes Reset Delete Selected Delete All Reset Description Click to enable the IP filtering security function. To restrict data transmission from local network on certain IP addresses, fill in the IP address and the protocol, also put your comments on it. The Protocol can be TCP, UDP or Both. Comments let you know about whys to restrict data from the IP address. Click the Apply Changes button to register the IP address to IP filtering list. Click the Reset button to abort change and recover the previous configuration setting. Click to delete the selected IP address that will be removed from the IP-filtering list. Click to delete all the registered entries from the IP-
filtering list. Click the Reset button to abort change and recover the previous configuration setting. 3.3.10 Firewall - MAC Filtering Entries in this table are used to restrict certain types of data packets from your local network to Internet through the Gateway. Use of such filters can be helpful in securing or restricting your local network. 19 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Firewall - MAC Filtering Description Apply Changes Item Enable MAC Filtering Click to enable the MAC filtering security function. MAC Address To restrict data transmission from local network on Comments certain MAC addresses, fill in the MAC address and your comments on it. Comments let you know about whys to restrict data from the MAC address. Click the Apply Changes button to register the MAC address to MAC filtering list. Click the Reset button to abort change and recover the previous configuration setting. Click to delete the selected MAC address that will be removed from the MAC-filtering list. Click to delete all the registered entries from the MAC-
filtering list. Click the Reset button to abort change and recover the previous configuration setting. Delete Selected Delete All Reset Reset 3.3.11 Firewall - Port Forwarding Entries in this table allow you to automatically redirect common network services to a specific machine behind the NAT firewall. These settings are only necessary if you wish to host some sort of server like a web server or mail server on the private local network behind your Gateway's NAT firewall. 20 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Firewall - Port Forwarding Item Enable Port Forwarding IP Address Protocol Port Range Comment Apply Changes Reset Delete Selected Delete All Reset Description Click to enable the Port Forwarding security function. To forward data packets coming from WAN to a specific IP address that hosted in local network behind the NAT firewall, fill in the IP address, protocol, port range and your comments. The Protocol can be TCP, UDP or Both. The Port Range for data transmission. Comments let you know about whys to allow data packets forward to the IP address and port number. Click the Apply Changes button to register the IP address and port number to Port forwarding list. Click the Reset button to abort change and recover the previous configuration setting. Click to delete the selected IP address and port number that will be removed from the port-forwarding list. Click to delete all the registered entries from the port-
forwarding list. Click the Reset button to abort change and recover the previous configuration setting. 3.3.12 Firewall - DMZ A Demilitarized Zone is used to provide Internet services without sacrificing 21 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 unauthorized access to its local private network. Typically, the DMZ host contains devices accessible to Internet traffic, such as Web (HTTP ) servers, FTP servers, SMTP (e-mail) servers and DNS servers. Screenshot Firewall - DMZ Description Click to enable the DMZ function. Item Enable DMZ DMZ Host IP Address To support DMZ in your firewall design, fill in the IP address of DMZ host that can be access from the WAN interface. Click the Apply Changes button to register the IP address of DMZ host. Click the Reset button to abort change and recover the previous configuration setting. Apply Changes Reset 3.3.13 Statistics This page shows the packet counters for transmission and reception regarding to wireless, Ethernet LAN and Ethernet WAN networks. 22 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Statistics Item Wireless LAN Sent Packets Wireless LAN Received Packets Ethernet LAN Sent Packets Ethernet LAN Received Packets Ethernet WAN Sent Packets Ethernet WAN Received Packets Refresh Description It shows the statistic count of sent packets on the wireless LAN interface. It shows the statistic count of received packets on the wireless LAN interface. It shows the statistic count of sent packets on the Ethernet LAN interface. It shows the statistic count of received packets on the Ethernet LAN interface. It shows the statistic count of sent packets on the Ethernet WAN interface. It shows the statistic count of received packets on the Ethernet WAN interface. Click the refresh the statistic counters on the screen. 3.3.14 Upgrade Firmware This page allows you upgrade the Access Point firmware to new version. Please note, do not power off the device during the upload because it may crash the system. 23 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Upgrade Firmware Item Select File Upload Reset Description Click the Browse button to select the new version of web firmware image file. Click the Upload button to update the selected web firmware image to the X-Micro WLAN Broadband Router. Click the Reset button to abort change and recover the previous configuration setting. 3.3.15 Save/ Reload Settings This page allows you save current settings to a file or reload the settings from the file that was saved previously. Besides, you could reset the current configuration to factory default. 24 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Save/Reload Settings Item Save Settings to File Load Settings from File Reset Settings to Default Description Click the Save button to download the configuration parameters to your personal computer. Click the Browse button to select the configuration files then click the Upload button to update the selected configuration to the X-Micro WLAN Broadband Router. Click the Reset button to reset the configuration parameter to factory defaults. 3.3.16 Password Setup This page is used to set the account to access the web server of Access Point. Empty user name and password will disable the protection. 25 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 Screenshot Password Setup Item Description User Name Fill in the user name for web management login control. New Password Fill in the password for web management login control. Confirmed Password Because the password input is invisible, so please fill in Apply Changes Reset the password again for confirmation purpose. Clear the User Name and Password fields to empty, means to apply no web management login control. Click the Apply Changes button to complete the new configuration setting. Click the Reset button to abort change and recover the previous configuration setting. 26 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 4 Frequently Asked Questions (FAQ) 4.1 What and how to find my PCs IP and MAC address?
IP address is the identifier for a computer or device on a TCP/IP network. Networks using the TCP/IP protocol route messages based on the IP address of the destination. The format of an IP address is a 32-bit numeric address written as four numbers separated by periods. Each number can be zero to 255. For example, 191.168.1.254 could be an IP address. The MAC (Media Access Control) address is your computer's unique hardware number.
(On an Ethernet LAN, it's the same as your Ethernet address.) When you're connected to the Internet from your computer (or host as the Internet protocol thinks of it), a correspondence table relates your IP address to your computer's physical (MAC) address on the LAN. To find your PCs IP and MAC address,
Open the Command program in the Microsoft Windows.
Type in ipconfig /all then press the Enter button.
Your PCs IP address is the one entitled IP Address and your PCs MAC address is the one entitled Physical Address. 4.2 What is Wireless LAN?
A wireless LAN (WLAN) is a network that allows access to Internet without the need for any wired connections to the users machine. 4.3 What are ISM bands?
ISM stands for Industrial, Scientific and Medical; radio frequency bands that the Federal Communications Commission (FCC) authorized for wireless LANs. The ISM bands are located at 915 +/- 13 MHz, 2450 +/- 50 MHz and 5800 +/- 75 MHz. 4.4 How does wireless networking work?
The 802.11 standard define two modes: infrastructure mode and ad hoc mode. In infrastructure mode, the wireless network consists of at least one access point connected to the wired network infrastructure and a set of wireless end stations. This configuration is called a Basic Service Set (BSS). An Extended Service Set (ESS) is a set of two or more BSSs forming a single subnetwork. Since most corporate WLANs require access 27 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 to the wired LAN for services (file servers, printers, Internet links) they will operate in infrastructure mode. Example 1: wireless Infrastructure Mode Ad hoc mode (also called peer-to-peer mode or an Independent Basic Service Set, or IBSS) is simply a set of 802.11 wireless stations that communicate directly with one another without using an access point or any connection to a wired network. This mode is useful for quickly and easily setting up a wireless network anywhere that a wireless infrastructure does not exist or is not required for services, such as a hotel room, convention center, or airport, or where access to the wired network is barred (such as for consultants at a client site). Example 2: wireless Ad Hoc Mode 4.5 What is BSSID?
A six-byte address that distinguishes a particular a particular access point from others. Also know as just SSID. Serves as a network ID or name. 4.6 What is ESSID?
The Extended Service Set ID (ESSID) is the name of the network you want to access. It is used to identify different wireless networks. 28 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 4.7 What are potential factors that may causes interference?
Factors of interference:
Obstacles: walls, ceilings, furniture etc.
Building Materials: metal door, aluminum studs.
Electrical devices: microwaves, monitors and electrical motors. Solutions to overcome the interferences:
Minimizing the number of walls and ceilings.
Position the WLAN antenna for best reception.
Keep WLAN devices away from other electrical devices, eg: microwaves, monitors, electric motors, etc.
Add additional WLAN Access Points if necessary. 4.8 What are the Open System and Shared Key authentications?
IEEE 802.11 supports two subtypes of network authentication services: open system and shared key. Under open system authentication, any wireless station can request authentication. The station that needs to authenticate with another wireless station sends an authentication management frame that contains the identity of the sending station. The receiving station then returns a frame that indicates whether it recognizes the sending station. Under shared key authentication, each wireless station is assumed to have received a secret shared key over a secure channel that is independent from the 802.11 wireless network communications channel. 4.9 What is WEP?
An optional IEEE 802.11 function that offers frame transmission privacy similar to a wired network. The Wired Equivalent Privacy generates secret shared encryption keys that both source and destination stations can use to alert frame bits to avoid disclosure to eavesdroppers. WEP relies on a secret key that is shared between a mobile station (e.g. a laptop with a wireless Ethernet card) and an access point (i.e. a base station). The secret key is used to encrypt packets before they are transmitted, and an integrity check is used to ensure that packets are not modified in transit. 4.10 What is Fragment Threshold?
The proposed protocol uses the frame fragmentation mechanism defined in IEEE 802.11 to achieve parallel transmissions. A large data frame is fragmented into several 29 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 fragments each of size equal to fragment threshold. By tuning the fragment threshold value, we can get varying fragment sizes. The determination of an efficient fragment threshold is an important issue in this scheme. If the fragment threshold is small, the overlap part of the master and parallel transmissions is large. This means the spatial reuse ratio of parallel transmissions is high. In contrast, with a large fragment threshold, the overlap is small and the spatial reuse ratio is low. However high fragment threshold leads to low fragment overhead. Hence there is a trade-off between spatial re-use and fragment overhead. Fragment threshold is the maximum packet size used for fragmentation. Packets larger than the size programmed in this field will be fragmented. If you find that your corrupted packets or asymmetric packet reception (all send packets, for example). You may want to try lowering your fragmentation threshold. This will cause packets to be broken into smaller fragments. These small fragments, if corrupted, can be resent faster than a larger fragment. Fragmentation increases overhead, so you'll want to keep this value as close to the maximum value as possible. 4.11 What is RTS (Request To Send) Threshold?
The RTS threshold is the packet size at which packet transmission is governed by the RTS/CTS transaction. The IEEE 802.11-1997 standard allows for short packets to be transmitted without RTS/CTS transactions. Each station can have a different RTS threshold. RTS/CTS is used when the data packet size exceeds the defined RTS threshold. With the CSMA/CA transmission mechanism, the transmitting station sends out an RTS packet to the receiving station, and waits for the receiving station to send back a CTS (Clear to Send) packet before sending the actual packet data. This setting is useful for networks with many clients. With many clients, and a high network load, there will be many more collisions. By lowering the RTS threshold, there may be fewer collisions, and performance should improve. Basically, with a faster RTS threshold, the system can recover from problems faster. RTS packets consume valuable bandwidth, however, so setting this value too low will limit performance. 4.12 What is Beacon Interval?
In addition to data frames that carry information from higher layers, 802.11 includes management and control frames that support data transfer. The beacon frame, which is a type of management frame, provides the "heartbeat" of a wireless LAN, enabling 30 USERS MANUAL OF X-MICRO WLAN BROADBAND ROUTER Version: 1.2 stations to establish and maintain communications in an orderly fashion. Beacon Interval represents the amount of time between beacon transmissions. Before a station enters power save mode, the station needs the beacon interval to know when to wake up to receive the beacon (and learn whether there are buffered frames at the access point). 4.13 What is Preamble Type?
There are two preamble types defined in IEEE 802.11 specification. A long preamble basically gives the decoder more time to process the preamble. All 802.11 devices support a long preamble. The short preamble is designed to improve efficiency (for example, for VoIP systems). The difference between the two is in the Synchronization field. The long preamble is 128 bits, and the short is 56 bits. 4.14 What is SSID Broadcast?
Broadcast of SSID is done in access points by the beacon. This announces your access point (including various bits of information about it) to the wireless world around it. By disabling that feature, the SSID configured in the client must match the SSID of the access point. Some wireless devices don't work properly if SSID isn't broadcast (for example the D-
link DWL-120 USB 802.11b adapter). Generally if your client hardware supports operation with SSID disabled, it's not a bad idea to run that way to enhance network security. However it's no replacement for WEP, MAC filtering or other protections. 31 75-115100-01
frequency | equipment class | purpose | ||
---|---|---|---|---|
1 | 2003-11-06 | 2412 ~ 2462 | DTS - Digital Transmission System | Original Equipment |
app s | Applicant Information | |||||
---|---|---|---|---|---|---|
1 | Effective |
2003-11-06
|
||||
1 | Applicant's complete, legal business name |
X-Micro Technology Corp.,
|
||||
1 | FCC Registration Number (FRN) |
0015779200
|
||||
1 | Physical Address |
12F-3, No. 186, Jian Yi Road, Chung Ho City
|
||||
1 |
Taipei Hsien, N/A 235
|
|||||
1 |
Taiwan
|
|||||
app s | TCB Information | |||||
1 | TCB Application Email Address |
h******@americanTCB.com
|
||||
1 | TCB Scope |
A4: UNII devices & low power transmitters using spread spectrum techniques
|
||||
app s | FCC ID | |||||
1 | Grantee Code |
RAF
|
||||
1 | Equipment Product Code |
XWL-11BRRG
|
||||
app s | Person at the applicant's address to receive grant or for contact | |||||
1 | Name |
L****** A****
|
||||
1 | Title |
Product Manager
|
||||
1 | Telephone Number |
886-2********
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
L******@x-micro.com
|
|||||
app s | Technical Contact | |||||
1 | Firm Name |
Advance Data Technology Corp.
|
||||
1 | Name |
E**** W****
|
||||
1 | Physical Address |
13-1 Lane 19 WenShan 3rd Street
|
||||
1 |
Taoyuan, 333
|
|||||
1 |
Taiwan
|
|||||
1 | Telephone Number |
+886-******** Extension:
|
||||
1 | Fax Number |
+886-********
|
||||
1 |
E******@adt.com..tw
|
|||||
app s | Non Technical Contact | |||||
n/a | ||||||
app s | Confidentiality (long or short term) | |||||
1 | Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | Yes | ||||
1 | Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?: | No | ||||
if no date is supplied, the release date will be set to 45 calendar days past the date of grant. | ||||||
app s | Cognitive Radio & Software Defined Radio, Class, etc | |||||
1 | Is this application for software defined/cognitive radio authorization? | No | ||||
1 | Equipment Class | DTS - Digital Transmission System | ||||
1 | Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant) | X-Micro WLAN 11b Boardband Router | ||||
1 | Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application? | No | ||||
1 | Modular Equipment Type | Does not apply | ||||
1 | Purpose / Application is for | Original Equipment | ||||
1 | Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization? | No | ||||
1 | Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization? | No | ||||
1 | Grant Comments | Power Output listed is Conducted. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter. End-users and installers must be provided with antenna installation instructions and transmitter operating conditions for satisfying RF exposure compliance. | ||||
1 | Is there an equipment authorization waiver associated with this application? | No | ||||
1 | If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded? | No | ||||
app s | Test Firm Name and Contact Information | |||||
1 | Firm Name |
Bureau Veritas CPS (H.K.) Ltd. Taoyuan Branch
|
||||
1 | Name |
T**** W****
|
||||
1 | Telephone Number |
886-2********
|
||||
1 | Fax Number |
886-2********
|
||||
1 |
t******@adt.com.tw
|
|||||
Equipment Specifications | |||||||||||||||||||||||||||||||||||||||||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Line | Rule Parts | Grant Notes | Lower Frequency | Upper Frequency | Power Output | Tolerance | Emission Designator | Microprocessor Number | |||||||||||||||||||||||||||||||||
1 | 1 | 15C | CE | 2412.00000000 | 2462.00000000 | 0.0400000 |
some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details
This product uses the FCC Data API but is not endorsed or certified by the FCC