Exhibit J User Manual XWS30W Xanboo/Core Technologies DRILLING TEMPLATE FOR WALL MOUNTING WATER SENSOR(S) ///
For wall mounting sensor(s), drill two holes using a 1/4 drill bit and the template below. Insert supplied wall anchors into holes and secure sensor to wall with supplied screws. Printers and copy machines can affect the scale of this template. Before drilling, compare this template with the actual sensor by placing the template on the back of the sensor and observing if mounting holes on sensor line up exactly with the drill holes on this template. WATER SENSOR DRILL HOLES IN THESE POSITIONS PRODUCT DESCRIPTION ///
The Shell HomeGenie Water Sensor monitors the presence or absence of water and notifies you when either is detected. You can use your Water Sensor to monitor the presence of water in basements/cellars, under sinks, and near water pipes. You can also monitor areas near other water sources such as an aquarium, water heaters, and washing machines. SHELL HOMEGENIE WATER SENSOR INSTALLATION EXAMPLE PACKAGE CONTENTS ///
n (1)Shell HomeGenie Water Sensor n (1)Water Sensor Probe n (1)Wall Mounting Kit SHELL HOMEGENIE WATER SENSOR WATER SENSOR PROBE WALL MOUNTING KIT INSTALLATION ///
The Shell HomeGenie Water Sensor is constructed of UV resistant ABS plastic allowing for indoor or sheltered outdoor use. When there is a change in status, either detecting or not detecting water, it is reported to the Motorola Gateway and an event is triggered. NOTE: The Water Sensor cannot be used on metal doors, metal doorframes or other metal objects. 1. Peel the paper strip from the double-sided tape located on the back of the sensor.
You can also mount the sensor more securely using the screws in the wall mounting kit. Using the
drilling template on the back of the instruction guide, drill two small holes for the screws.
Affix the screws to any object leaving 1/16 space between the screw head and the object, 2.Mount the Water Sensor onto the screws and slide down to lock into place. 3.Mount the Water Sensor Probe on a vertical surface, such as a baseboard or a sump wall,
using either one screw or the double-sided tape located on the back. 4.Plug the Water Sensor Probe jack into the base of the Water Sensor. HELPFUL HINTS ///
The Shell HomeGenie Water Sensor is suitable for indoor and outdoor use. Please bear in mind the following points when choosing a mounting position:
n The Water Sensor cannot be mounted on metal doors, metal door frames or metal objects. n Be sure to use 2-AAA alkaline batteries from a reliable manufacturer. Currently the sensor
does not support rechargeable NiCad or NiMH batteries. However, the sensor does have
power saving functionality. n You should periodically test the batteries by pushing the discovery button located on the back
of the Water Sensor. If battery power is available the LED indicator will light. FAQS ///
HOW FAR AWAY CAN THE SENSOR BE PLACED FROM THE MOTOROLA GATEWAY?
Typically 60 feet. CAN I PLACE THE SENSOR IN A DIFFERENT ROOM FROM THE MOTOROLA GATEWAY?
Yes, the sensor uses radio frequencies to communicate with the Motorola Gateway. These frequencies can travel through objects such as walls, ceilings, and floors. HOW LONG WILL THE BATTERY LAST?
The batteries are expected to last up to 12 months. This will depend on actual use and how often the Water Sensor is triggered. HOW MANY SENSORS CAN I USE WITH MY MOTOROLA GATEWAY?
The Motorola Gateway can support up to 20 sensors. THE LED INDICATOR ON THE SENSOR IS NOT ON?
This indicates that the sensor has gone into hibernation mode to save battery power. It will wake up when the sensor is triggered. WATER I 2 TECHNICAL SPECS ///
n Attaches to vertical flat surfaces n Operates on 2-AAA Alkaline batteries n LED indicator when sensor is triggered n Test/Discover button Typical Range Outdoors: Typical Range Indoors: Frequency Range: APPROVALS ///
250 feet 60 feet 418 MHz FCC ID NUMBER: OU4-XWS30W / IC: 4576A-XWS30W STANDARDS 93/68/EEC, 89/336/EEC, BS EN 50082-1:1992, 73/23/EEC, EN60950:1992 CE INSTRUCTIONS TO THE USER:
The user is cautioned that changes and modifications made to the equipment without the approval of manufacturer could void the user's authority to operate this equipment. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interferences will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help. CE directive 93/68/EEC, EMC directive 89/336/EEC, LV directive 73/23/EEC. This class B digital apparatus complies with Canadian ICES-003. The term IC: before the certification/registration number only signifies that the Industry Canada technical specifications were met. Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device. Increase the separation between the equipment and receiver. 3 4