FCC ID: YMX-EC3209K1 Massage Chair

Instruction Manual AM-Juno II ISEDC warning Control Buttons on the side panel 1-2 3 4 5 6 7 8-9 10-11 12 13 14-17 18 19 20 21 Keep Dry Do not operate in a wet or moist condition. 1 2 3 This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment . 4 ISEDC warning This device complies with Innovation, Science, and Economic Development Canad licence-exempt RSS standard(s). Operation is subject to the following two conditions:

(1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d' Innovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :

(1) l'appareil nedoit pas produire de brouillage, et

(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le fonctionnement. The device is compliance with RF exposure guidelines, users can obtain Canadian information on RF exposure and compliance. Le prsent appareil est conforme Aprs examen de ce matriel aux conformit ou aux limites dintensit de champ RF, les utilisateurs peuvent sur lexposition aux radiofrquences et la conformit and compliance dacqurir les informations correspondantes. 5 4 4 6 7 1.PREPARATION contains footrest. This model is come with 2 boxes packing design : Box 1 contains main body and Box 2 Connect the cable to outlet and chair .Switch ON the current,the chair will return back to the original position.(Caution:the assembly for footrest will be easy after the chair had returned to original position.Unplug the cable after the chaire return to original position). 2.Footrest assemble 1.Connect the wire connectors and screw the cap tight.Then connect the air hose. Caution:after the wire connector have been connected the cap must be screwed tight. 8 2.Remove the two circlips on the bolts,then attach the footrest onto the base and lock the circlips. Caution:please attach on the long bolt first. 3.Zip the zipper between the seat pad 4.Connect the chair to a power supply and footrest. turn on the power switch,the chair will be ready to start. 9 10 11 Controller 1.Power 3/4.Spot/Zone 7.Time 9.Wake up 10.Healthy 12.Revitalize 15.Arm 16.Shoulder 19.Recline 20.Upright 21.Up 22.Down 2.Pause 5/6. -/+

8.Zero Gravity 11. Classic 13.Relax 14.Stretch 17.Foot Air 18.Vibrate 23.Speed 24.Manual 25.Intensity 26.Width HEALTHY WAKE UP RELAX REVITALIZE CLASSIC STRETCH SHOULDER ARM FOOT AIR VIBRATE RECLINE UPRIGHT UP DOWN SPEED MANUAL INTENSITY WIDTH 12 Intensity adjustment Blue tooth Heating Footrest massage Auto program Position adjustment Remark:the blue tooth button will light when the blue tooth is open,then remote will show blue tooth icon. Wireless charging USB charging 13

How to Start Function Description 1.Power The power button starts and stops all functions on the massage chair. Press once, the chair is idle mode. Press again, all functions will stop, and massage rollers will return to original position. The pause button will allow all massage functions to stop temporarily. Press once, all the massage functions and timer will be stopped temporarily. Press again to resume the massage session. This key with two functions: one is for spot massage and one is for making roller upward. Press once, it will allow users to choose the exact position to massage. Hold the key and dont release, it will move roller upward. When the roller reach the position needed, stop holding the key. This can be applied to all massage selections. This key with two functions: one is for zone massage and one is for making roller Press once, it will allow uses to limit the massage in 12cm long to a particular body Hold the key and dont release, it will move roller downward. When the roller reach the position needed, stop holding the key. 2.Pause 3.Spot 4.Zone downward. zone. 5/6.-/+

Press each time to adjust intensity of Kneading Massage. 14 7.Time The timer button controls the length of the massage session. The default time for all massage functions is 15 minutes. Press each time to change the length of the time in the following sequence:

20>25>30>5>10>15. 8.Zero Gravity Adjust the angle of the massage chair to zero gravity position. Press to achieve position required.Press again to resume to original position. Engages the Snooze Auto Program, based on the waist by Kneading, Shiatsu and other Help to shape up body and relieve stress. Rolling and tapping will be activated at the area of mid and low back. Recommended for sore mid and low back. Engages the deep tissue massage to loosen up the muscles. This program focuses on neck, shoulder and hip by Rolling and Kneading, reduction of 9.Wake up techniques. 10.Healthy 11. Classic 12.Revitalize body fatigue. 13.Relax Combination of kneading and tapping massage kicks off the full body. With kneading and tapping, start from the head, down to the lower back, and focus on the buttocks. 15 This function allows users to adjust the strength of massage. There are total 5 levels for your options. This function activated the air compression on arm area. This function activated the air compression on shoulder area. This function activated the air compression on foot area. This button control the vibration in seat area. Press once to activate vibration.Press again to stop the vibration. 14.Stretch 15.Arm 16.Shoulder 17.Foot Air 18.Vibrate 19.Recline 20.Upright This button controls recline angle of the massaging chair. Press once, the backrest and footrest will move to a horizontal reclining position. This button control incline angle of the massage chair. Press once, the backrest and footrest will move to an upright sitting. Press again to stop the product at your preferred angle. 21.Up Adjust back massage position. Press the button to choose position of massage rollers when a "beep" sound alerts in 10 seconds. Release the button once the desired position is achieved. 16 22.Down Adjust back massage position. Press the button to choose position of massage rollers when a "beep" sound alerts in Release the button once the desired position is achieved. Control the speed of Tapping, Kneading, Swedish, Shiatsu, Kneading and tapping Select a massage function and press to select between 5 speeds. Controls Kneading, Tapping, Swedish, Shiatsu, Kneading and tapping ,Rolling massage. Press once to activate kneading massage of the full back. Each press of button, the massage mode changes in sequence: Tapping>Swedish>

Shiatsu>Kneading and Tapping>Rolling. This button allows users to adjust the intensity of airbag on the calves and feet area. There are five levels for your option. This button allows you to control the width of the rollers. Select a massage function and press to adjust between Narrow, Normal and Wide 10 seconds. 23.Speed massage. 24.Manual 25.Intensity 26.Width widths. 17 18 19 20 AM-Juno II 130W 57.1 29.5 42.9 67.3 29.5 33.5 213.8 177.5 This equipment contains a certified radio transmission module:

FCCID2AOC9-ZENBDM10A ICID27631-ZENBDM10A 21

Massa Model:

Rated!

Rated 1 Serial}

Made Ir FCC ID:Y) IC: 7284A:

Contains This device is subject t

(1) This dev

(2) This dev interferenc XIAMEN CC ye Chair EC-320s 1 China MiX-EC3209

-EC3209K1 FCC ID:2A\

IC :27631

> complies w o the followii ice may not fice must acc e that may ce JMFORT SCI K1 OC9-ZENBI

-ZENBDM1 ith Part 15 of ng two condi cause harmf

-ept any inter ause undesir ENCE & TECI

-60Hz DM10A 0A the FCC Rul tions:

ul interferenc ference rece ed operation HNOLOGY Gi les. Operatior ce, and sived, includi i ROUP CO.,LT ing

XIAMEN COMFORT SCIENCE & TECHNOLOGY GROUP CO., LTD Agent Authorization Letter 2022-05-27 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 USA RE: LETTER OF AGENT AUTHORIZATION To Whom It May Concern:

We, the undersigned, hereby authorize Shenzhen Most Technology Service Co., Ltd. to act on our behalf in all matters relating to application for equipment authorization, including the signing of all documents relating to these matters. We also hereby certify that no party to the application authorized hereunder is subject to the denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C.853(a). This agreement expires one year from the current date. Sincerely, Name:

Position:

Company Name:

Address:

Tel / Fax E-Mail:

Pengfei Cui Safety Engineer XIAMEN COMFORT SCIENCE & TECHNOLOGY GROUP CO., LTD

(5/F) NO.168, QIANPU ROAD, SIMING DISTRICT, XIAMEN, CHINA

+86-592-7266925/ +86-592-5532788 cpf.cui@easepal.com.cn

Model difference letter 2022.05.27 TO: Innovation, Science and Economic Development Canada Certification and Engineering Bureau 3701 Carling Ave., Bldg. 94, Ottawa, ON, K2H 8S2 This is a new Application from XIAMEN COMFORT SCIENCE &

TECHNOLOGY GROUP CO., LTD Model No.:

EC-3209K, AM-Juno II Only the model EC-3209K was tested, since the electrical circuit design, layout, components used and internal wiring were identical for the above models, with difference being the name of the product, the name of the model Thank you for your cooperation!

Yours sincerely, Signatory:

Pengfei Cui Safety Engineer XIAMEN COMFORT SCIENCE & TECHNOLOGY GROUP CO., LTD

(5/F) NO.168, QIANPU ROAD, SIMING DISTRICT, XIAMEN, CHINA

+86-592-7266925/ +86-592-5532788 cpf.cui@easepal.com.cn Name:

Position:

Company Name:

Address:

Tel / Fax E-Mail:

XIAMEN COMFORT SCIENCE & TECHNOLOGY GROUP CO., LTD Long Term Confidentiality Request Letter 2022-05-27 Eurofins Electrical and Electronic Testing NA, Inc. 914 West Patapsco Avenue Baltimore, MD 21230 USA RE: CONFIDENTIALITY REQUEST FOR (FCC ID:YMX-EC3209K1) To Whom It May Concern:

This letter serves as an official request for confidentiality under sections 0.457 and 0.459 of CFR 47. We have requested that the

- e.g. Block diagram

- e.g. SCH

- e.g. Operational Description required to be submitted with this application be permanently withheld from public review. The above documents are company proprietary information that could never get into the possession of your competition. Please contact me if there is any information you may need. Sincerely, Name:

Position:

Company Name:

Address:

Tel / Fax E-Mail:

Pengfei Cui Safety Engineer XIAMEN COMFORT SCIENCE & TECHNOLOGY GROUP CO., LTD

(5/F) NO.168, QIANPU ROAD, SIMING DISTRICT, XIAMEN, CHINA

+86-592-7266925/ +86-592-5532788 cpf.cui@easepal.com.cn