FCC ID: 2AUTE-3358 Handheld Barcode Scanner (BT)

Appearance Power on/off and Restart Bluetooth Connection USB Connection FCC ID:2AUTE-3358 Handheld Barcode Scanner HN-3358SR Start up:

1. Automacally start up aer connecng USB;

2. When USB is not connected, press the scanning buon to start the scanner. Shut down:

touch). Restart:

1. Press and hold for 15s to shut down;

2. Shut down automacally aer 15 minutes of silence (without any If the scanner crashes or does not response, press the boom switch with the paper clip. Then press the scanning buon to restart. Maintenance The reading window must be kept clean. Avoid hard and rough objects to scratch the reading window. Remove the stains from window with a brush. Please use a so cloth to clean the window, such as glasses cloth. Do not spray any liquid on the window Do not use any cleanner other than cleaning water. Instruction Manual Sound Hole Scan Window Scan Buon Indicator Type-C Shutdown Hole The scanner is shut up by pressing the scanning buon, and be 1) Connect the device interface (type-C interface) of USB to scanner;

connected it to the host devices through Bluetooth. The green light 2) Connect the host interface (USB interface) of USB to the host and indicates that it is connected and can be used normally. switch to the keyboard mode. Buzzer Status Power on Scan Successfully Beeping mes 3 mes 1 Interface Setting The scanner can communicate with the host by RS-232 serial port or USB port. The user can switch to the corresponding interface by replacing the cable and scanning the corresponding barcode below. 1USB virtual keyboard LED Indicator Color Red light on Red light o Red light ash Description Charging Full charge Low power prompt Green light slow ash Bluetooth not connected Green light on Bluetooth connected Alternang slow ashing Charging and Bluetooth not of red and yellow light connected Yellow light on Charging and Bluetooth connected 2USB virtual Serial Port 3Bluetooth Bluetooth Connection Bluetooth Connection Scanning Mode Common Problem State FCC Warning FCC Warning

(1) Set shut down/up me Pop up iPhone keyboard by Bluetooth 2 Scan mode sengs by scanning the barcode below 1Manual Mode 2Sensing Mode Disable 5min Yes No 3connuous Mode 10min 15min Scan the barcode to restore all sengs to the factory default state. Set Deafults 30min 60min Note: Please use the factory reset funcon carefully. Aer recognizing this barcode, the current parameter sengs will be lost and replaced with the factory default values. 1Aiming Barcode 2Read Successfully Barcode Other ON OFF ON OFF QThere are some barcodes can not be scan. A a) Firstly, check the barcode type and enable the barcode funcon; if there is veried, try to close the vericaon. b) Unable to know the barcode type, then set all barcodes allow to be read. QThe barcode data is incorrect. A Check the status of barcode errors (whether all barcodes have errors or specic barcodes have errors) QBar code can be read but not displayed. A First, conrm whether the working mode of the scanner is in Bluetooth transmission mode; if it is already in Bluetooth trans-

mission mode, conrm whether the Bluetooth of the scanner is connected to the host terminal. Q Aiming light and illumuniaon light are not on. A a) Check whether the device is powered on. b) Re-plug the data cable. Our company does not assume any responsibility for losses caused by natural disasters (such as earthquakes, oods, etc.) that exceed our scope of responsibility. In any case, our company does not assume any responsibility for losses caused by using this product, such as loss of prots, loss of reputaon, business interrupon, loss or change of stored data, and any special, unexpected, associated or intermient losses ca-

used by the above. Our company does not assume the responsibility for the losses ca-

used by due to improper use of hardware or soware not specied by the our company . Our company does not provide any form of warranty or technical support for the informaon, data, les, other products, services obtained though the use of this product, and does not assume any responsibility for the use of above descripon by users. Our company are not take any form of guarantee for third-party soware used by this product. Due to the connuous improvement of the products, the operaon and common problems of the models described in the manual are mainly based on actual machines. And it may be changed without noce. This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:

(1) This device may not cause harmful interference, and

(2) this device must accept any interference received, including int-

erference that may cause undesired operaon. NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency ene-

rgy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interfer-

ence to radio or television recepon, which can be determined by tu-

rning the equipment o and on, the user is encouraged to try to corr-

ect the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separaon between the equipment and receiver.

- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

- Consult the dealer or an experienced radio/ TV technician for help. Warning:

Changes or modicaons to this unit not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. FCC Radiaon Exposure Statement The device has been evaluated to meet general RF exposure require-

ment. The device can be used in portable exposure condion without restricon.

Xiamen Hanin Electronic Technology Co.,Ltd. Date: 08/14/2020 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 To Whom It May Concern:

The Xiamen Hanin Electronic Technology Co.,Ltd., the undersigned, hereby authorizes Mr. Qijie Xiao from Kehu-Morlab Test Laboratory to act on the behalf of the Xiamen Hanin Electronic Technology Co.,Ltd. solely in matters relating to the application for an FCC equipment authorization for FCC ID:

2AUTE-3358 including the signing of documents in connection with this Application. Necessary acts carried out Kehu-Morlab Test Laboratory on our behalf of the Xiamen Hanin Electronic Technology Co.,Ltd. in connection with the Application shall have the same effect as acts of the Xiamen Hanin Electronic Technology Co.,Ltd.. Xiamen Hanin Electronic Technology Co.,Ltd. also hereby certify that no party to this application is subject to a denial of benefits, including FCC benefits, pursuant to Section 5301 of the Anti-Drug Abuse Act of 1988, 21 U.S.C. 862. Thank you for your attention to this matter. Yours Sincerely,

| Signatory: . , j Dun (2m (u Contact name: QinQin Yu Title: Certified Engineer Tel: 15705965171 Email: yugingin@prttech.com Company name: Xiamen Hanin Electronic Technology Co.,Ltd.

Xiamen Hanin Electronic Technology Co.,Ltd. Date:08/14/2020 To: Federal Communications Commission, Authorization & Evaluation Division, 7435 Oakland Mills Road, Columbia, MD 21046 Re: Request of Confidentiality for FCC ID: 2AUTE-3358 To Whom it may concern:

Pursuant to sections 0.457 and 0.459 of Commissions Rules(CFR 47), and Section 552(b)(4) of the Freedom of Information Act, Xiamen Hanin Electronic Technology Co.,Ltd. hereby requests confidentiality and treatment of certain information accompanying this application. The materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these matters might be harmful to the Applicant and provide unjustified benefits to its competitors. We are also hereby request Short-Term Confidentiality till date 02/01/2021(max time 180 days from grant date) as outlined in Public Notice DA04-1705. This provision will give Xiamen Hanin Electronic Technology Co.,Ltd. temporary confidentiality of commercially sensitive information prior to product release. The requested Permanent and Short-Term Confidential exhibits are listed as follows:

PERMANENT AND SHORT-TERM CONFIDENTIAL LIST Exhibit Description Block Diagram Operational Description PERMANENT Schematics BOM External Photos Internal Photos Test-Setup Photos User Manual SHORT-TERM CO}N | OD) Or) B) |r) The Applicant understands that pursuant to Rule 0.457, disclosure of this application and all accompanying documentations, where applicable, will not be made public before the date of the Grant for this application. Signatory Name: QinQin Yu Company name: Xiamen Hanin Electronic Technology Co.,Ltd. Address: Room 305A, Angye Building, Pioneering Park,Torch High-tech,Zone,Xiamen Tel: 15705965171 Email: yugingin@prttech.com

(2vn Wan Yu

Xiamen Hanin Electronic Technology Co.,Ltd. Suppliers Declaration Of Conformity for the FCC SDoC Procedure The following equipment:

Product Name Brand Name

: Handheld Barcode Scanner

: HPRT, N/A Model Number

N130BT, BP130BT, HN-3358XX-XXXR (XX represents the focal distance of lens maybe SR/ MR / LR / HD / HP / WA, etc;X represents software version,maybe (0-9);XX represents customer code,maybe (00-99);R represents ROHS certification) Report Number

: XM20080015E01 Per FCC Part 2 Subpart J 2. 1077(a) Its herewith confirmed to comply with the requirements of FCC Part 15 Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and

(2) This device must accept any interference received, including interference that may cause undesired operation. It is understood that each unit marketed is identical to the device as tested, and any changes to the device that could adversely affect the emission characteristics will require retest. Signatory:

Contact name:QinQin Yu Tel:+86 15705965171 Email:yuqinqin@prttech.com Company name: Xiamen Hanin Electronic Technology Co.,Ltd. The following importer / manufacturer is responsible for this declaration:

Company Name Company Address Telephone

Person is responsible for marking this declaration:

Fax :

Name (Full name) Position / Title Date Legal Signature There are not Available United States importer / responsible party at Certification Stage.