Appearance Power on/off and Restart Bluetooth Connection USB Connection Handheld Barcode Scanner HN-3358SR Start up:
1. Automacally start up aer connecng USB;
2. When USB is not connected, press the scanning buon to start the scanner. Shut down:
touch). Restart:
1. Press and hold for 15s to shut down;
2. Shut down automacally aer 15 minutes of silence (without any If the scanner crashes or does not response, press the boom switch with the paper clip. Then press the scanning buon to restart. Maintenance The reading window must be kept clean. Avoid hard and rough objects to scratch the reading window. Remove the stains from window with a brush. Please use a so cloth to clean the window, such as glasses cloth. Do not spray any liquid on the window Do not use any cleanner other than cleaning water. Instruction Manual Sound Hole Scan Window Scan Buon Indicator Type-C Shutdown Hole The scanner is shut up by pressing the scanning buon, and be 1) Connect the device interface (type-C interface) of USB to scanner;
connected it to the host devices through Bluetooth. The green light 2) Connect the host interface (USB interface) of USB to the host and indicates that it is connected and can be used normally. switch to the keyboard mode. Buzzer Status Power on Scan Successfully Beeping mes 3 mes 1 Interface Setting The scanner can communicate with the host by RS-232 serial port or USB port. The user can switch to the corresponding interface by replacing the cable and scanning the corresponding barcode below. 1USB virtual keyboard LED Indicator Color Red light on Red light o Red light ash Description Charging Full charge Low power prompt Green light slow ash Bluetooth not connected Green light on Bluetooth connected Alternang slow ashing Charging and Bluetooth not of red and yellow light connected Yellow light on Charging and Bluetooth connected 2USB virtual Serial Port 3Bluetooth Bluetooth Connection Bluetooth Connection Scanning Mode Common Problem State FCC Warning FCC Warning
(1) Set shut down/up me Pop up iPhone keyboard by Bluetooth 2 Scan mode sengs by scanning the barcode below 1Manual Mode 2Sensing Mode Disable 5min Yes No 3connuous Mode 10min 15min Scan the barcode to restore all sengs to the factory default state. Set Deafults 30min 60min Note: Please use the factory reset funcon carefully. Aer recognizing this barcode, the current parameter sengs will be lost and replaced with the factory default values. 1Aiming Barcode 2Read Successfully Barcode Other ON OFF ON OFF QThere are some barcodes can not be scan. A a) Firstly, check the barcode type and enable the barcode funcon; if there is veried, try to close the vericaon. b) Unable to know the barcode type, then set all barcodes allow to be read. QThe barcode data is incorrect. A Check the status of barcode errors (whether all barcodes have errors or specic barcodes have errors) QBar code can be read but not displayed. A First, conrm whether the working mode of the scanner is in Bluetooth transmission mode; if it is already in Bluetooth trans-
mission mode, conrm whether the Bluetooth of the scanner is connected to the host terminal. Q Aiming light and illumuniaon light are not on. A a) Check whether the device is powered on. b) Re-plug the data cable. Our company does not assume any responsibility for losses caused by natural disasters (such as earthquakes, oods, etc.) that exceed our scope of responsibility. In any case, our company does not assume any responsibility for losses caused by using this product, such as loss of prots, loss of reputaon, business interrupon, loss or change of stored data, and any special, unexpected, associated or intermient losses ca-
used by the above. Our company does not assume the responsibility for the losses ca-
used by due to improper use of hardware or soware not specied by the our company . Our company does not provide any form of warranty or technical support for the informaon, data, les, other products, services obtained though the use of this product, and does not assume any responsibility for the use of above descripon by users. Our company are not take any form of guarantee for third-party soware used by this product. Due to the connuous improvement of the products, the operaon and common problems of the models described in the manual are mainly based on actual machines. And it may be changed without noce. This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including int-
erference that may cause undesired operaon. NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency ene-
rgy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interfer-
ence to radio or television recepon, which can be determined by tu-
rning the equipment o and on, the user is encouraged to try to corr-
ect the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separaon between the equipment and receiver.
- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help. Warning:
Changes or modicaons to this unit not expressly approved by the part responsible for compliance could void the users authority to operate the equipment. FCC Radiaon Exposure Statement The device has been evaluated to meet general RF exposure require-
ment. The device can be used in portable exposure condion without restricon. FCC ID 2AUTE-HN3358