Connection LED Indicator Operation LED Indicator Cover-opening Button Power Button Cover-opening Button USB Interface USB Cable1 Rear View Accessories Product Introduction Front View Loading Paper Roll 01 Open the top cover Loading Paper Roll 03 Load the paper roll Push the cover-opening buttons on both sides,and open the top cover. Load the paper roll to the paper compartment again and pull some extra paper.Please adjust the separator according to the paper width. Power On 01 Power on Hold down the power button for 3 seconds to start the printer. Printing Wirelessly from Mobile Phone 01 Download App Scan the QR code below to download HiprintApp. Battery Charging When the battery is low, the indicator light will ash (red light ashes quickly). Please use the matching USB cable to charge in time. If you continue printing, the printer may shut down automatically. cover-opening button Separator 02 Remove the paper roll 04 Close the top cover Remove the supplied paper roll and tear it apart along the edge. Close the top cover after loading paper.Please make sure both sides click Turn on the printer. into place. charging by PC charging by power adapter To turn o the printer, also hold down the power buon for 3 seconds. Printing from Windows PC Connect one side of the USB cable to the PC and the other side to the printer. Download the driver program from HPRT website,and install it in the PC. Add the printer to the PC and print the documents from the PC after establishing the connection. 03 Printing Tip: Default page by page printing mode.Click the power button to continue printing after one page is printed.For continuous printing, go to the printer driver setting and set it to continuous printing mode. 02 Connect the Printer Open App, click +in the top right corner,select MT seriesSelect connect via 'system settings',mobile phone bluetooth selectMT810-XXXXXXXX is last four digits of Bluetooth address,click and connect. Return HiprintApp,and click the device and connect. Precauons The best operang temperature is 0
~40
, if the environmental temperature is too low or too high, the print quality may be aected. Please do not use the unocial adapter or paper roll to ensure the print quality. During prinng, the area around the thermal print head is very hot. Do not touch it, as you could be burned. Do not pull out the paper by force during prinng, or else it may damage the printer. Open the document to be printed on the mobile phone and copy it to
"Hiprint"Or select document printing on the App home page. Set it in the print preview as required, and then click Print. Note: App operation shall be subject to the latest version. 01 02 03 05 06 Please purchase and use HPRT ocial thermal paper. 04 LED Indicator and Buzzer Denions Operaon LED indicator, which shows the printer status itself 01 Error Status Status Print head temperature is too high Out of paper/paper jam/
abnormal paper loading LED Indicator Red LED ashes rapidly Buzzer Beep-beep beep-
Red LED ashes slowly Beep beep beep-
Voltage/Baery is too low Red LED ashes rapidly Beep-beep-beep-
Printer cover is not closed Red LED is lighng Printer Status Status Power on Power o Prinng Sleeping LED Indicator White LED is lighng Light o White LED ashes slowly Blue LED is lighng 02 Status LED Indicator In Bluetooth connecon Blue LED is lighng Bluetooth data receiving Blue LED ashes rapidly In USB connecon Green LED is lighng USB data receiving Green LED ashes rapidly No connecon currently Light o Connecon LED indicator, which shows the connecon status of printer Product Parameters Product Name Mobile Printer Product Model MT810 Battery Parameter 7.4V, 2500mAh Dimensions 280 x 95 x 51.4mm Weight About 1kg (without accessories) Operating Temperature 0~40 Executive Standard GB4943.1-2011, GB/T9254-2008, GB 17625.1-2012 FCC WARNING This device complies with part 15 of the FCC Rules. Operaon is subject to the following two condions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operaon. Any changes or modicaons not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protecon against harmful interference in a residenal installaon. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instrucons, may cause harmful interference to radio communicaons. However, there is no guarantee that interference will not occur in a parcular installaon. If this equipment does cause harmful interference to radio or television recepon, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separaon between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. 07 08 MT810