FCC ID: 2AUTE-2DT23JR Portable Label Printer

Product Introduction Appearance and Components Packing List Product Introduction Indicator Status Paper Loading Instruction Paper Loading Instruction Use both hands to pry the cover apart on both sides. 01 03 Move the paddle switch up and adjust the paper limiter according to the width of the paper roll. After adjustment, press down the paddle switch and lock the paper limiter. APP Download Scan QR code to download the app:

Connect Printing HerePrint APP HereLabel APP Open the Hancode app and click on "My" - "Connect Device". Check the list of "Bluetooth devices", nd "HM-T260L-XXXX", and click to connect. Battery charging If you need to charge, please use a USB Type-C to Type-A cable and connect the power adapter (self provided, adapter output not higher than 5V/1A) to the printer for charging. When the battery level is low, the indicator light will ash (white, ashing once per second). Please charge in a timely manner. If you continue printing, the printer may automatically shut down. Charging through PC Type-C Charging Port Reset Hole Quick Start Guide Printer The actual content inside the box shall be based on the actual object. Tear Bar White Light Abnormal State Constant brightness: abnormal

(paper shortage/cover opening/TPH overheating) Slow ashing: low battery Flash: Firmware upgrade in progress Basic State Slow ashing: charging Always on: Printer ready/Bluetooth connected successfully/Bluetooth disconnected

/Bluetooth lost White Light On/O Long press the power button for 3 seconds to turn it on/o. Power Button Indicator Light 02 As shown in the following gure, install the paper roll with the thermal side facing outward. Thermosensitive Layer 04 Pull out a small piece of paper and close the lid. Click "New" - "New Label". Set the label width and height based on the actual size of the label paper. Charging through power adapter Edit the labels as needed, click "Next" after editing, and then print. Note: You can use a power adapter or computer USB for power supply, and the adapter is not included when shipping. If consumers use a power adapter for charging, they should purchase and use a power adapter that has obtained CCC certication and meets the standard requirements. Online WeChat Customer Service

(Warranty/After Sales/Technical Support) FCC WARNING This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any changes or modications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one or more of the following measures:

-- Reorient or relocate the receiving antenna.

-- Increase the separation between the equipment and receiver.

-- Connect the equipment into an outlet on a circuit dierent from that to which the receiver is connected.

-- Consult the dealer or an experienced radio/TV technician for help. To NOTE: This equipment has been tested and found to comply with the maintain compliance with FCCs RF Exposure guidelines, This equipment limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. should be installed and operated with minimum distance between 20cm These limits are designed to provide reasonable protection against harmful the radiator your body: Use only the supplied antenna. interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. HM-T260LR

Reference No.: WTX23X11255924W001/002/003 Page 1 of 12 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech, Zone, Xiamen, China Date: 2024-01-02 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref:

Attestation Statements Part 2.911(d) (5) (i) Filing SUBJECT: FCC Application for FCC ID: 2AUTE-2DT23JR To Whom It May Concern:

Xiamen Hanin Electronic Technology Co.,Ltd. certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Sincerely, Signatory

[Jeff Wang, Certified Engineer]

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech, Zone, Xiamen, Chin Date: 2024-01-02 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 Ref:

Attestation Statements Part 2.911(d) (5) (ii) Filing SUBJECT: FCC Application for FCC ID: 2AUTE-2DT23JR To Whom It May Concern:

Xiamen Hanin Electronic Technology Co.,Ltd. certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List (as a specifically named entity or any of its subsidiaries or affiliates) as an entity producing covered equipment. Sincerely, Signatory

[Jeff Wang, Certified Engineer]

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech,Zone, Xiamen, China Date: 2024-01-02 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2AUTE-2DT23JR Confidentiality Request To whom it may concern, Pursuant to the provisions of the Commissions rules Title 47 Sections 0.457 and 0.459, we are requesting the Commission to withhold the following attachment(s) as confidential documents from public disclosure indefinitely. Block Diagram Operational Description Schematics Parts List Tune-Up Information Security Information Software Defined Radio (SDR) Information The above materials contain trade secrets and proprietary information not customarily released to the public. The public disclosure of these materials may be harmful to the applicant and provide unjustified benefits to its competitors. In additional to above mentioned documents, in order to comply with the marketing regulations in Title 47 CFR 2.803 and the importation rules in Title 47 CFR 2.1204, while ensuring that business sensitive information remains confidential until the actual marketing of newly authorized devices, we request Short Term Confidentiality of the following attachment(s);

External Photos Internal Photos Test Setup Photos User Manual For 45 days, pursuant to Public Notice DA 04-1705. or For 180 days pursuant to KDB 726920 D01. The applicant understands that pursuant to Section 0.457 of the Rules, disclosure of this application and all accompanying documentation will not be made before the date of the Grant for this application. Sincerely, Signatory

[Jeff Wang, Certified Engineer]

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech,Zone, Xiamen, China Date: 2024-01-02 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 SUBJECT: FCC Application for FCC ID: 2AUTE-2DT23JR To Whom It May Concern:

I, the undersigned, hereby states this equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules, and will apply the Supplier's Declaration of Conformity procedure to the class B computer peripheral portion of this composite device. I understand the following FCC requirements:

1. Devices subject to the SDoC procedure are required to be tested to show compliance with the FCC technical regulations by a recognized accredited testing laboratory. The testing laboratory must be accredited by a Commission approved accreditation body or designated under the terms of a government-to-government Mutual Recognition Agreement (MRA). A listing of those accredited testing laboratories that have been recognized by the Commission is published on the FCC Webpage:

https://apps.fcc.gov/oetcf/eas/reports/TestFirmSearch.cfm (Select the "accredited" option to search for FCC recognized accredited test firms.) 2. Pt 2.1077 contains the list of information that must be included in the Supplier's Declaration of Conformity, which must be supplied with each product sold. The SDoC compliance info shall be included in the Users Manual or as a separate sheet. The info must contain the name, address, and phone number of the responsible party, which must be located within the United States. According to 2.909(b), the responsible party is either the Manufacturer or if the product is imported the Importer. Sincerely, Signatory

[Jeff Wang, Certified Engineer]

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech,Zone, Xiamen, China

January 2, 2024 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCCID: 2AUTE-2DT23JR TO WHOM IT MAY CONCERN:

We place the FCC label in the Printer bin due to below reasons:

1. 2. 3. The FCC label is visible when user opens the Printer bin door and place the photo paper into Printer, otherwise, the equipment doesnt work. The equipment is separated from the photo paper and the cover in the packing box, users can read the FCC ID information at the time of purchase. Label placed on the exterior of the equipment affect the appearance according to design requirements; otherwise, it would be easily removed or damaged. Sincerely, Signatory

[Jeff Wang, Certified Engineer]

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech,Zone, Xiamen, China Date: 2024-01-02 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCCID: 2AUTE-2DT23JR Model Declaration Letter Dear Regulatory Authority, Model(s): HCL-2DT23JR, HM26R are same to the model HM-T260LR, these models are same PCB Layout, Schematics, BOM. Only for different model name and appearances for different market require. Sincerely, Signatory

[Jeff Wang, Certified Engineer]

Xiamen Hanin Electronic Technology Co.,Ltd. Room 305A, Angye Building, Pioneering Park, Torch High-tech,Zone, Xiamen, China Date: 2024-01-02 FEDERAL COMMUNICATIONS COMMISSION AUTHORIZATION AND EVALUATION DIVISION 7435 OAKLAND MILLS ROAD COLUMBIA, MD 21046 SUBJECT: FCC Application for FCC ID: 2AUTE-2DT23JR POWER OF ATTORNEY To Whom It May Concern:

We, the undersigned, hereby authorize Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf, to apply to the Federal Communications Commission on our equipment. Any and all acts carried out by Waltek Testing Group (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in full compliance with the Anti-Drug Abuse Act. We, Xiamen Hanin Electronic Technology Co.,Ltd. are not subject to a denial of federal benefits pursuant to Section 5301 of the Anti-Drug Act of 1988, 21 USC853a, and no party to the application is subject to a denial of federal benefits pursuant to that section. Sincerely, Signatory

[Jeff Wang, Certified Engineer]