Technology For Life Access Control Reader Xiamen Leelen Technology Co., Ltd. No.65 Sunban South Road, Jimei North Industrial Zone, Jimei District, Xiamen National Unified Service Hotline 95105895 Website: http://en.leelen.com The product shall be subject to the actual equipment Users Manual V1.0 RP.B06.ZC-SM.006
. Equipment Appearance View
. Installation Diagram 1 Installation Way 1.1 Fix the rear shell with the screw to the 86 box. CARD Access control port Lockpower supplyfire alarm door status detection port
. Wiring Instructions Access control reader Digital access control Door Exit Power Fire status button supply alarm NO NC COM
+
-
10 FIRE G G STATE OPEN cores socket Access control port B A black red purple blue green yellow orange orange red brown 1 Lock black white grey 1.2 Fasten the front shell to the back of the rear shell. 1.3 Use the screws to tighten the front shell and rear shell, complete the installation. 2 V. Function 1 This device can receive the instruction sent by outdoor unit or digital access controller, so that the lock controlled by this device can be opened normally. 2 When receiving the swiping card information, the card data can be uploaded to the digital access controller so that the digital access controller can unlock the corresponding door. 3 This device has anti-dismantle, anti-removal detecting and alarm function. 4 When the effective card is recognized, the access control reader emits "beep" sound and then it emits a long beep sound;
When the invalid card is recognized, the "beep" sound emitted by the access control reader is followed by two short bursts of beep sound 5 Users can use the IC cardto unlock 2 Installation Precautions 2.1 Before installation, please read the product instructions, confirm the wiring mode, and ensure that the input voltage complies with the product requirements. 2.2 Please make sure the product is used within the range of the technical parameters; if not, this may cause damage to the product. 2.3 Non-professionals shall not take the product apart;
otherwise, it may cause electric shock or damage to the product. 2.4 Do not install the equipment outdoors or in heavily -dusty places. 2.5 High voltage is dangerous! Non-professionals shall not open the housing. Technical Specifications Product name: Access control reader Rated working voltage: 12~24DC Static working current: 38mA Maximum working current: 90mA Environment temperature: -40~75 External dimension: 120*86*19.5mm Degree of protection: IP54 3 4
. Dial Switch
. Restricted Substances The equipment has three dialing switches, dial switch 1 is low, 3 is high, and the representative address information is shown in the following table. 3 ON ON ON ON OFF OFF OFF OFF 2 ON ON OFF OFF ON ON OFF OFF 1 ON OFF ON OFF ON OFF ON OFF Address 1 2 3 4 5 6 7 8 Part Name Metal part Plastic part CRT display screen LCD screen Circuit board component*
Power cord/
cable Power/
adapter Packaging Toxic and hazardous substances or elements
(Pb)
(Hg)
(Cd)
(Cr6+)
(PBB)
(PBDE) O O X O X X X O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O O This form was prepared in accordance with SJ/T 11364 *:
O: It indicates that the contents of the hazardous substance in all homogeneous materials of the part are below the limit requirement specified in GB/T 26572 X: It indicates that the contents of the hazardous substance in at least one of the homogeneous materials of the part exceed the limit requirement specified in GB/T26572
*: Circuit board components include a printed circuit board and its components, such as resistors, capacitors, integrated circuits, etc. 5 6
* FCC This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-- Consult the dealer or an experienced radio/TV technician for help. 7