WARNING:pdfminer.pdfpage:The PDF <_io.BufferedReader name='/Volumes/Scratch/Incoming/eg-scratch/6699549.pdf'> contains a metadata field indicating that it should not allow text extraction. Ignoring this field and proceeding. Use the check_extractable if you want to raise an error in this case 1. Packing List 2. Hardware Introduction 3. Power Button and LED Patterns 4. Configuration Guide Presence Sensor DESK & SEAT OCCUPANCY SENSOR 1 x VS340 & VS341 Sensor 4 PIR Covers 1 3M Tape LED Indicator PIR Sensor Power Button PIR Sensor 2 Mounting Kits 1 Quick Start Guide 1 Warranty Card Mounting Holes
NFC Area PIR Cover Thermopile Sensor
(VS341 Only) Mounting Holes LED Indicator Battery Thermopile Sensor
(VS341 Only)
1. Download Milesight ToolBoxApp on an NFC-supported smartphone. Power On/Off Press and hold the power button for more than 3 seconds Check On/Off Status Quick press the power button Power OnOffOn Power OffOnOff Light OnDevice is on. Light Off: Device is off. Reset to Factory Default Press and hold the power button for more than 10 seconds Blinks quickly Android iOS Occupancy Status VacantOccupied OccupiedVacant Blinks twice Blinks twice 2. Open Milesight ToolBox App and attach the NFC area of the smartphone to device, click NFC Read to read/write the device until the App successfully shows a prompt. Its suggested to change the default password for security reasons. (Default password: 123456)
5. Installation
PIR Cover Installation Take off the front cover of the device, then select the PIR cover as required and put it on the PIR sensor with groove alignment. The adjustable angle of every groove is 30. The PIR cover can also be tailored according to requirements. Fixed by 3M Tape Fixed by Mounting Kits Attach 3M tape to the back of sensor, then tear the other side and place it under the working desk. Please adjust the installation direction according to the detection area and ensure that the thermopile sensor should be placed toward the seat. 1. Take off the front cover of the device, then fix the wall plugs under the desk according to the device mounting holes, then fix the device to the wall plugs with screws. Please adjust the installation direction according to the detection area and ensure that the thermopile sensor should be placed toward the seat. 2. Restore the front cover back to the device. 6. FCC Statement Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and.
(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits aredesigned to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator& your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. Cloud App Quick Start Guide All oftware & files can be downloaded from https://www.milesight-iot.com/documents-download/
Milesight IoT Co., Ltd. www.milesight.com Building C09, Software Park Phase III, Xiamen 361024, Fujian, China