User Instructions for Remote IC Information This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-exempt RSS(s). Operation is subject to the following two conditions:(1) This device may not cause interference.and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppement conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1. Lappareil ne doit pas produire de brouillage;
2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Remote Control Accessory Information Note:
The 1. Battery 2. battery of the remote control can be replaced. model: CR2032. Status Indicator Power Button Dimming Button
(UP) Dimming Button
(Down) Screw Remote Control Junction box bracket Junction box
(1pc)
(1pc) auxiliary bracket Wall bracket
(1pc)
(1pc) Battery Holder 3.Tools Needed To Install FCC Information This device complies with Part 15 of the FCC Rules. Operation is Status subject to the following two conditions:
2.9.1 Indicator Indicator lights white:
5mm Screwdriver Philips Electrical Tape Press any button once. Cutter 4.Installation Test Pencil Plier Ruler Model No. RDNA042C Rated Voltage 3VDC
! WARNINGSAND CAUTIONS 1.Chemical Burn Hazard. Keep batteries away from children. 2.This product contains a lithium button/coin cell battery. If a new or used lithium button/coin cell battery is swallowed or enters the body, it can cause severe internal burns and This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television can lead to death in as little as 2 hours. Always completely reception, which can be determined by turning the equipment off and secure the battery compartment. If the battery compartment on, the user is encouraged to try to correct the interference by one or does not close securely, stop using the product, remove the more of the following measures:
batteries, and keep it away from children. If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention. 3.The cells shall be disposed of properly, including keeping them away from children. 4.Even used cells may cause injury. RF EXPOSURE STATEMENT This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. Cet quipement est conforme l'exemption des limites d'valuation habituelle de la section 2.5 de la norme RSS-102.
- Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION Any changes or modifications to this unit not expressly approved by the manufacture could void the user's authority to operate the equipment. Button on:
Short off: Short mode Power Turn Turn Pairing the pairing within once indicator stops 2.10.1 2.10.2 2.10.3 enters control) status once when once when control:
the the press press of mode, 15s. remote press After blinking. power pairing OFF. in in ON. When the dimmer button (remote is successful, the once can increase a 2.11.1 of level Dimming Button (UP) press Short brightness press Long brightness the
.brightness. the when in the dimming ON dimming until continuous 2.11.2 increase max 2.11.3 Short press the dimming button(up) 2 times continuously when in ON/OFF status to turn quickly to the max. brightness. can reach the release to button status. button or 4.1.1 Installing the base to fixed the remote control
(Installation the junction box with panel) Installation the Junction box auxiliary bracket on the Junction box bracket. Junction box auxiliary bracket Junction box bracket 2.12.1 level a Dimming Button (Down) press brightness press Short of Long when the the dimming ON in dimming until 2.12.2 decrease min.brightness. the brightness once button status. button release can or reach the can decrease Secure the junction box bracket securely with the continuous to mounting screws provided. 2.12.3 Continuous status short quickly to turn to 2 press the min. when times brightness. in ON/OFF Junction Box Junction box bracket Screws 4.1.2 Installing the panel Installing the panel base on the Junction box bracket and tighten with the matched screws. Wall Mode two:
Expansion screw Junction box bracket Screws according to the wall bracket hole, drill two holes on the wall, and into the expansion bolt, the wall bracket with mounting screws fixation. Wall Junction box bracket Panel base Screws Expansion screw Wall bracket Screw Remote control 4.2.2 Installing the panel Installing the panel base on the Junction box bracket and tighten with the matched screws. Wall Junction box bracket 4.4 Remote control battery replacement Panel base Screws Hold the card buckle both ends of the battery compartment pull it out then remove the battery compartment. Put the panel on the panel base , press gently to make it to make sure it installed firmly. Panel base Remote control Battery holder Battery holder Remote control Battery holder remove the old battery from the battery holder, change new battery (CR2032), Reinstall the battery box on the remote control. Old battery New batteryCR2032 Battery holder Battery holder Remote control Battery holder Panel Remote control Put the panel on the panel base , press gently to make it to make sure it installed firmly. Panel base 4.2.1 Wall installing with panel according to the junction box bracket hole, drill two holes on the wall, and into the expansion bolt, with mounting screws to junction box support fixation. Panel Remote control 4.3 Wall installing without panel Mode one :
Peel off the wall bracket's stripping layer of back adhesive and attach the wall bracket to the wall and fix it firmly. Wall Wall bracket Remote control Adhesive surface Stripping layer