FCC ID: 2AV7W-PDNA012W Smart Plug-in Dimmer

Installation Instructions for Smart Plug-in Dimmer Works with DIMMABLE LED, CFL, Incandescent and halogen bulbs Model No. PDNA012U2-W-300 Rated Voltage 120V,60Hz Rated Power 300W Load Range Incandescent.: 15W-300W LED/CFL: 3W-200W

: 3W-200W

: 3W-200W Dimming type Phase-cut dimming Operating Temperature 0~35 Operating Humidity 10% R.H.-90% R.H. Size 45.5 47 50.5 mm FCC Information This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation.This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help. FCC CAUTION Any changes or modifications to this unit not expressly approved by the manufacture could void the user's authority to operate the equipment. RF EXPOSURE STATEMENT This equipment complies with the FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. This equipment meets the exemption from the routine evaluation limits in section 2.5 of RSS-102. It should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body. Cet quipement est conforme l'exemption des limites d'valuation habituelle de la section 2.5 de la norme RSS-102. Il doit tre install et utilis une distance minimale de 20 cm entre le radiateur et toute partie de votre corps. IC Information This device contains licence-exempt transmitter(s) that comply with Innovation, Science and Economic Development Canadas licence-ex-

empt RSS(s). Operation is subject to the following two conditions:

(1) This device may not cause interference.and (2) This device must accept any interference, including interference that may cause undesired operation of the device. Lmetteur/rcepteur exempt de licence contenu dans le prsent appareil est conforme aux CNR dInnovation, Sciences et Dveloppe-

ment conomique Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:

1. Lappareil ne doit pas produire de brouillage;

2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. WARNINGS AND CAUTIONS After installed the dimmer, it is recommended to set the minimum brightness level to make bulbs turn on immediately. If you are unsure about any part of these instructions, consult a licensed electrician. To reduce the risk of overheating and possible damage to other equipment do not install to control a motor-operated receptacle, fluorescent lighting fixture, or a transformer supplied receptacle. Use with compatible dimmable LED, CFL bulbs, Incandescent or halogen fixtures only. When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs shall be either LED, CFL or Incandescent.Using the same model of each bulb will enhance dimmer performance. Functional parts instructions ON/OFF button Status indictor Status indictor Indicator lights red : The load lights are OFF and no App connect. Indicator lights yellow : The load lights are ON and no App connect. Indicator lights green : App has connected. Indicator lights green and flash: In the EZ connection mode, indicator lights green and flashes quickly (flash once every 2 seconds); or In the AP connection mode, indicator lights green and flashes slowly (flash once every 4 seconds). Quick to the Max. brightness: Continuous press ON/OFF button twice. Set the Min. brightness : Turn on the light and dim to the Min. brightness you desired, continuous press ON/OFF button 6 times then finished the Min. brightness setting. Recover to the factory default Min. brightness: Turn on the light, continuous press ON/OFF button 9 times. Enter to the EZ network connection mode: Turn on the light, continuous press ON/OFF button 5 times, status indicator will flash quickly(flash once every 2s),then your phone can connect to the dimmer. The light will flash once when successed the connection .

(The dimmer will exit connection mode after 3 minutes of inactivity.) Enter to the AP network connection mode: Turn on the light, continuous press ON/OFF button 7 times, status indicator will flash slowly(flash once every 4s),then your phone can connect to the dimmer. The light will flash once when successed the connection.

(The device will exit connection mode after 3 minutes of inactivity.) Recover to factory default: Turn on the light,continuous press ON/OFF button 10 times,the lights flash once mean recovered.

(Default: 1.Turn on the light will at Max. brightness; 2. The min. brightness at 1% ; 3.Current at EZ network connection mode.) Function Description Table of the functions Function Operation method Turn ON/OFF Dimming Quick to the Max. brightness Set the Min. brightness Reset the default brightness EZ network connection mode AP network connection mode Reset to the factory default Schedule ON/OFF Share device Group control Press once Press/Press and hold Press twice Press 6 times Press 9 times Press 5 times Press 7 times Press 10 times

Dimmer operation phone operation The opreation of device itself could stop the operation of mobile APP, when at the opreation of device itself ,mobile APP operation couldnt work. Priority Troubleshooting Symptoms Possible Cause Solution Lights flickering LED and CFL flickers at low end of dimming range Lamp has a bad connection Reconnect and fix the wires One dimmer connect to multiple types bulb, incur interference and cause flicker Change bulbs to same type Load compatibility is not good Turn up lamp minimum brightness properly Circuit breaker has tripped Turn power on Light does not turn on Fuse burn out Change fuse Lamp burned out Change lamp Lamp has a bad connection Reconnect the circuit Light does not respond Abnormal Restart the power ON/OFF button Turn ON/OFF: Press ON/OFF button once. Dimming: Press and hold to dim the lights,releas then press and hold again to change the dimming direction. Quick to the Max. brightness: Continuous press ON/OFF button twice. Mobile app operation Step 1 Download the Smart Life App Use your mobile device to scan the QR code below or search for

"Smart Life" in the App Store or Google play to download and install the app. Step 2 Register an account and Login Open the Smart Life app,click Register to create an account and login. 4G 09:36 35%

Step 3 Add Device Click Add Device or the top right-hand corner + ;

Click lighting then to enter the device connection interface;

Lighting

(Wi-Fi) Regitser Login with Existing Account 4G 09:36 35%

My home Welcome Home Set your home location for more informa... >

All Devices No devices,please add Add Device Home Smart Me 09:36 35%

Add Manually Auto Scan Lighting Lighting

(Wi-Fi) Lighting

(Bluetooth) Lighting

(ZigBee) Lighting Product...

(Bluetooth) 4G

Electrical Engineeri... Large Home Ap... Small Home Ap... Kitchen Appliance Security

&Sensor Exercise

&Health Others Step 4 Mobile device connection Step 4a EZ network connection mode:

Turn on the light, continuous press ON/OFF button 5 times, status indicator lights green and flash quickly(flash once every 2s), and load lights flash once mean enter to the paring mode; then your phone can connect to the device. Confirm the Status indicator flash quickly,click Enter your Wi-Fi password and click then waitting for the connection. Confirm indicator rapidly blink Confirm The load light flash once when successed the connection. 4G

09:36 35%

Add Device AP Mode Reset the device first. If the light blinking fast, skip the reset step Power on Turn On-off-on-off-on(Subject to User Manual) Ensure light is fast blinking Off/On3 Resetting Devives >

Confirm indicator rapidly blink 4G

09:36 35%

Add Device Enter Wi-Fi Password Only 2.4 GHz Wi-Fi networks are supported

Change Network

Confirm 4G

09:36 35%

Add Device Connecting... Place your router, mobile phone, and device as close as possible 23%

Device found Register Device to Smart Cloud Initializing device AP network connection mode:

Step 4b Turn on the light, continuous press self-reset switch 7 times, status indicator lights green and flash slowly(flash once every 4s), and load lights flash twice mean enter to the paring mode; then your phone can connect to the device. Click APMode to enter the operation interface. Confirm the status indicator flash slowly,click Enter the Wi-Fi password in your home and click Click ,connect to the Wi-Fi that comes with the dimmer and return, waiting for the connection. Confirm indicator rapidly blink Go to Connect Confirm The load light flash once when successed the connection. 4G

Add Device AP Mode AP Mode 4G

Reset the device first. If the light blinking fast, skip the reset step Power on Turn On-off-on-off-on(Subject to User Manual) Ensure light is fast blinking Reset the device first. If the light blinking fast, skip the reset step Power on On-off-on-off-on, after the flash is flashing, turn"on-off-on-off-on,"(Subject Ensure light is slowly blinking to User Manual) Off/On3 Off/On3

... Off/On3 Resetting Devives >

Resetting Devives >

Confirm indicator rapidly blink Confirm indicator slowly blink 4G

AP Mode 4G

AP Mode 09:36 35%

09:36 35%

4G 09:36 35%

Add schedule and then save it. Enter Wi-Fi Password Only 2.4 GHz Wi-Fi networks are supported

Connect your mobile phone to the device's hotspot 1.Connect the phone to the hotspot shown below. 4G 09:36 35%

< Wi-Fi Wi-Fi Home Guest 4G Change Network SmartLife_XXXX i Confirm Go to Connect Click to enter the operation interface. Done 4G

09:36 35%

AP Mode Connecting... Place your router, mobile phone, and device as close as possible 23%

Device found Register Device to Smart Cloud Initializing device 4G

09:36 35%

Add Device Device added successfully Wi-Fi Dimmer Done Wi-Fi Dimmer Setting

Brightness: 70%

Back 4G 09:36 35%

Wi-Fi Dimmer Setting

Brightness: 14%

Click to enter the minimum brightness interface for setting dimmer. Select the bulb type which connected with the dimmer. Set the minimum brightness of the light and save it. 4G 09:36 35%

4G 09:36 35%

Setting Setting Select Type of Your Lamp Click Reselect Select Type of Your Lamp Click Reselect Set the minimum brightness of the dimmer Please set the minimum brightness of your lamp,and try to dim your lamp.If the lamp is flashing or turned off,increase the brightness until it workks well. Set the minimum brightness of the dimmer Please set the minimum brightness of your lamp,and try to dim your lamp.If the lamp is flashing or turned off,increase the brightness until it workks well. 0%

24%

Reselect bulb type LED Incandescent CFL Lamp Cancel Step 5 Mobile phone app control outlet dimmer Click to control the light on/off function of the dimmer. Click to enter the dimming interface for dimming. Click Set the schedule light on/off function of the dimmer. Add Sharing Save Device is not shared,add an account to share it 4G

Time variance is30s 09:38 35%

09:38 35%

Schedule Schedule Save 4G

08 56 09 57 AM 10 58 PM Repeat Switch Once >

ON >

No time data Add Schedule Brightness: 14%

After the dimmer connection is completed, it can be shared to many people, that is, one dimmer can be controlled by multiple APPs. Click to enter the device details interface;

Click Share Device to enter the device sharing interface. 4G 09:36 35%

09:38 35%

Wi-Fi Dimmer Setting

Device Location 4G

More Device Name Wi-Fi Dimmer >

Check Device Network Check Now >

Third-party Control Alexa GoogleAssist ant Others Share Device Create Group Device Information FAQ & Feedback Add to Home Screen Click Add Sharing, add the account you are willing to sharing. 4G 09:38 35%

09:38 35%

4G

Add Sharing Done Cancel Device Sharing In a permanent resident in your home has an account,we recommend that you set the account as a family member and share all your family devices and smart scenarios with the family member.Family Settings Country/... United States of America +1 >

Account 626********

Support Amazon Alexa and Google Home voice control For Amazon Alexa Alexa,turn on <device name>

Alexa,turn off <device name>

Alexa,set <device name> to percent Alexa,brighten/increase <device name>

Alexa,dim/decrease <device name>

For Google Home Hey Google,turn on <device name>

Hey Google,turn off <device name>

Hey Google,is <device name> on/off?

Hey Google,brighten/increase <device name) Hey Google,Dim/Brighten <device name> by 50%

09:36 35%

09:36 35%

4G 4G 09:36 09:36 35%

35%

4G 09:36 35%

4G 09:36 35%

Wi-Fi Dimmer Wi-Fi Dimmer Wi-Fi Dimmer Wi-Fi Dimmer Setting >

Setting >

Setting

Setting

Power Off Power Off Brightness: 14%

Brightness: 14%

Reference No.: WTX21X12136361W Page 1 of 13 ANNEX EXHIBIT 1 - PRODUCT LABELING Proposed FCC ID Label Format Specifications: The label shall be securely affixed to a permanently attached part of the device, in a location where it is visible or easily accessible to the user, and shall not be readily detachable. The label shall be sufficiently durable to remain fully legible and intact on the device in all normal conditions of use throughout the devices expected lifetime. Proposed Label Location on EUT FCC ID Label Location Waltek Testing Group (Shenzhen) Co., Ltd. Http://www.waltek.com.cn

Xiamen Tenia Lighting & Elect cal Co., Ltd. No.575,Second Ring South Road, Tong'an District, Xiamen, Fujian, China Dale 2422-42-24 Federal Communicat ons Comm ss on Authorization and Eva uat on Div s on 7435 Oakland Mills Road Columb a, NID 21046 FCC D: 2AV^V-PDNAo12W Confidentiality Request To whom t may concern, tr Block Diagram tr Operational Descr ption

: Schernat cs

! Parts L st Pursuant to Sections 0 457 and 0.459 of the Commission s Rules we hereby request confident a treatment of the information accompar]ying lh s app cation as out ined be ow:

f Tune-Up lnforr.ation f Security nformat on f Software Defined Radio (SDR) information The above materials conta n tTade secrets and proprietary information not customarily re eased to the publ c The public d sclosure of these mater als may be harmful to the appl cant and provide unlustfied benefits to its competitors. The applicant understands lhat pursuant to Sectlon 0 457 of the Ru es. disclosure of this appl cation and a I accompanying documentation wi I not be made before the date of the Grant for this applcation Sincerely, Xiamen Ten a Llghting & Electr cal Co., Ltd. (Wenlong Zhang)

(General I\,4anager)

Xiamen Tenj.a lightj-ng & E].ectrical Co., ltd.

)ai@en, Eujian, Chlna No.575iSecond Ring South Road, Tong,an Distilct,

(FCC ID : 2AV7W-PDNA012'r) POIIER OF ATTORNEY DAEE: 2022-02-24 Eederal Communlcations Comission Aurnori_a"o' "'d -/. 1". o. Drvrsron

?435 Oakland Mills Road columbia. r'1D 21046 To Whom It May Concern:

i{e, the undersigned, hereby authorize Wallek Testing Group (Shenzhen) Co., trd. Jandy so on our behalf, to appLy to the Federal Comunications Conmassaon on our equlpment. Any and all acls carried out by Waltek Testinq croup (Shenzhen) Co., Ltd. Jandy So on our behalf shall have the same effect as acts of our own. This is to advise that we are in lul] compliance with ihe Anli-Drug Abuse Acr. we, xiamen Tenia l,ighting & Eleclrical Co./ Itd. aie not subject to a deniat of federal beneiits pursuanir to secrion 5301 of rhe Anti-Drug Act of 1988, 21 Usc853a, and no party to the application is subject to a denial of federal D"n.ri s p ,. "

.ec-ron. o .t-. Xiamen Tenia Liqhtinq , Electrical Co., Ltd. t^lry r\

{wenlonq zhang)

(GeneraI Manager)