FCC ID: 2BCGR-HS501003 Bluetooth Module

HS5010-03 Bluetooth module specification V1.0 Directory 1, product characteristics 2, electrical parameters 3, the appearance size 5, foot position definition 5, schematic 6, contact us 1 product features:

1, Based on LE5010 Bluetooth low energy research and development 2, Support private APP access, 2.4G remote control access 3, Bluetooth module designed with Bluetooth 5.0 low energy design, 4, Working voltage: 1.8~3.6V 5, Working temperature: -40 degrees ~ +80 degrees (commercial specifications) 6, SMD package Bluetooth features:

1 BLE5.0/5.1 2, Support 125Kbps/500Kbps/1Mbps/2Mbps 3. Receiving sensitivity: -99.7dBm @1Mbps

-96dBm @2Mbps

-105dBm @125Kbps 4, Transmission power: maximum +12dBm (max) 5, Link gain 117@125Kbps (max.) 6, SUPPORT FOR SIG MESH, PRIVATE MESH AND BLE MCU features:

1, 32BIT CPU CORE 2. Up to 64M main frequency 3, Maximum 64KB SRAM 4, MAX 512 FLASH 5, RX mode: 4.5mA 1, TX mode: 4.3mA @0DB 2, Deep sleep: 1.1UA (GPIO+RTC wake-up) 3, ShutDOWN: 700NA (GPIO wake-up) 4, Real-time clock RTC 5, peripheral interface: UART 6, All IOs support function mapping, Scope of application:

1, LED intelligent control 2, Smart home appliances 3. Exercise health 4, Sports wearable 5, Logistics label 6. Consumer products 2 Electrical parameters Voltage MIN Supply voltage 1.7 I/0 voltage Operating temperature 0

-40 Storage

-40 temperature Power consumption TYP 3.3

MAX Unit 3.6 3.6

+85 V V degree

+125 degree RX MODE TX MODE@0DB TYP 4.5 4.3 Deep sleep 1.1UA(GPIO+RTC) ShutDOWN 700NA(GPIO) unit mA mA uA nA 3) module shape and interface:

1, HS5010-03 (small size module) Size: 18X10X2.6mm (L*W*H) Definition PIN Pin Name Pin Name 1 2 GND PB15 GND GPIO/low-power wake-up pin/continuous low level into sleep; High-level wake-up;

There is a pull-up inside the dangling, which wakes up by default 3 PA00 indicates Bluetooth connection status;

BLE or SPP is connected and the output is high BLE and SPP are not connected, and the output is low serial port data input UART_RX PA02 serial port data output UART_TX GND Operating voltage range 1.8-3.6V GPIO 4 5 6 7 8 PA01 PA02 GND VCC PA14 5) The schematic Confidential Notes:

1, power supply, try to use a clean power supply, ripple control within 30mV 2, Antenna 2.1 The module can choose the on-board antenna or the external wire antenna, when laying the patch when laying the board, it is necessary to achieve complete headroom for the antenna, do not lay copper and wire;

2.2: The side of the IC on the module cannot face the high-frequency components on the drive, but the outside of the drive board;

2.3: The module should be far away from the high-frequency components on the drive;

2.4: The antenna placement of the module should be taken into account when the PCB layout of the driver is carried out;

2.5: For the module of the welding antenna, there are front welding and back welding methods, if the module of the front welding antenna is not well placed during the layout, you can consider using the module of the back welding antenna 6) Contact Us:

mailas1@hosotech.com FCC Statement FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 Device is equipped with PCB antenna, Antenna gain 3dBi This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Any Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. FCC Radiation Exposure Statement This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following: Contains Transmitter Module FCC ID:

2BCGR-HS501003 Or Contains FCC ID: 2BCGR-HS501003 When the module is installed inside another device, the user manual of the host must contain below warning statements;

1. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference;

(2) This device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. 2. Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. The devices must be installed and used in strict accordance with the manufacturer's instructions as described in the user documentation that comes with the product. Any company of the host device which install the modular with modular approval should perform the test of radiated & conducted emission and spurious emission, etc. according to FCC part 15C : 15.247 and 15.209

& 15.207 ,15B Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209

& 15.207 ,15B Class B requirementthen the host can be sold legally.

DATE: Aug 22.2023 Federal Communications Commission Authorization & Evaluation Division 7345 Oakland Mills Road Columbia, Maryland 21046 Authority to Act as Agent On our behalf, | appoint_BlueAsia of Technical Services(Shenzhen) Co.,Ltd. Building C, No. 107, Shihuan Road, Shiyan Sub-District, Baoan District, Shenzhen, Guangdong Province, China (Name of Agent company name and address) to act as our agent in the preparation of this application for equipment certification. | certify that submitted documents properly describe the device or system for which equipment certification is sought. | also certify that each unit manufactured, imported or marketed, as defined in the Federal Communications Commission s regulations will have affixed to it a label identical to that submitted for approval with this application.For instances where our authorized agent signs the application for certification on our behalf, | acknowledge that all responsibility for complying with the terms and conditions for certification, still resides with Xiamen Zhuoye Technology Co., Ltd. /Unit 602, No. 21 Pingcheng North Road, Haicang District, Xiamen, Fujian Province Xiamen Fujian Province China (Applicant Name and address)

<Signature>

Name: Mingling sun J!NG LinG Sun Title: manager Applicant Company: Xiamen Zhuoye Technology Co., Ltd.

DATE: 2023-08-22 Equipment Autorisation Division Federal Communications Commission 7435 Oakland Mills Road Columbia, MD 21046 FCCID:2BCGR-HS501003 Product Name: Bluetooth Module Request for Confidentiality Pursuant to Sections 0.457 and 0.459 of the commissions rules, we hereby request that the following documents be held confidential:

(List here the documents for which you are seeking confidentiality for example ...) e Schematics e Block diagram Operation description These materials contain trade secrets and proprietary information and are not customarily released to the public. The public disclosure of this information might be harmful to the company and provide unjustified benefits to our competitors.

<Signature> \ F Name: MingLing Sun Mwy Ling Sul Title: manager Applicant Company: Xiamen Zhuoye Technology Co., Ltd.

YES FCC standards: FCC CFR Title 47 Part 15 Subpart C Section 15.247 N/A Yes YES Refer to instruction Device is equipped with PCB antenna, Antenna gain 3dBi Comment Refer to instruction Compliance list INTEGRATION INSTRUCTIONS for 996369 D03 OEM the and 996369 D03 OEM by Sections 2.2 through 2.10. Requirement 2.2 List of applicable FCC rules List the FCC rules that are applicable to the modular transmitter. These are the rules that specifically establish the bands of operation, the power, spurious emissions, and operating fundamental frequencies. DO NOT list compliance to unintentional-radiator rules

(Part 15 Subpart B) since that is not a condition of a module grant that is extended to a host manufacturer. See also Section 2.10 below concerning the need to notify host manufacturers that further testing is required.3 2.3 Summarize the specific operational use conditions Describe use conditions that are applicable to the modular transmitter, including for example any limits on antennas, etc. For example, if point-to-point antennas are used that require reduction in power or compensation for cable loss, then this information must be in the instructions. If the use condition limitations extend to professional users, then instructions must state that this information also extends to the host manufacturers instruction manual. In addition, certain information may also be needed, such as peak gain per frequency band and minimum gain, specifically for master devices in 5 GHz DFS bands. 2.4 Limited module procedures If a modular transmitter is approved as a limited module, then the module manufacturer is responsible for approving the host environment that the limited module is used with. The manufacturer of a limited module must describe, both in the filing and in the installation instructions, the alternative means that the limited module manufacturer uses to verify that the host meets the necessary requirements to satisfy the module limiting conditions. A limited module manufacturer has the flexibility to define its alternative method to address the conditions that limit the initial approval, such as: shielding, minimum Not applicable N/A N/A signaling amplitude, buffered modulation/data inputs, or power supply regulation. The alternative method could include that the limited module manufacturer reviews detailed test data or host designs prior to giving the host manufacturer approval. This limited module procedure is also applicable for RF exposure evaluation when it is necessary to demonstrate compliance in a specific host. The module manufacturer must state how control of the product into which the modular transmitter will be installed will be maintained such that full compliance of the product is always ensured. For additional hosts other than the specific host originally granted with a limited module, a Class II permissive change is required on the module grant to register the additional host as a specific host also approved with the module. 2.5 Trace antenna designs For a modular transmitter with trace antenna designs, see the guidance in Question 11 of KDB Publication 996369 D02 FAQ Modules for Micro-Strip Antennas and traces. The integration information shall include for the TCB review the integration instructions for the following aspects: layout of trace design, parts list (BOM), antenna, connectors, and isolation requirements.4 a) Information that includes permitted variances (e.g., trace boundary limits, thickness, length, width, shape(s), dielectric constant, and impedance as applicable for each type of antenna);

b) Each design shall be considered a different type (e.g., antenna length in multiple(s) of frequency, the wavelength, and antenna shape

(traces in phase) can affect antenna gain and must be considered);

c) The parameters shall be provided in a manner permitting host manufacturers to design the printed circuit (PC) board layout;

d) Appropriate parts by manufacturer and specifications;

e) Test procedures for design verification; and f) Production test procedures for ensuring compliance. The module grantee shall provide a notice that any deviation(s) from the defined parameters of the antenna trace, as described by the instructions, require that the host product manufacturer must notify the module grantee that they wish to change the antenna trace design. In this case, a Class II permissive change application is required to be filed by the grantee, or the host manufacturer can take responsibility through the change in FCC ID (new application) procedure followed by a Class II permissive change application. 2.6 RF exposure considerations It is essential for module grantees to clearly and explicitly state the RF exposure conditions that permit a host product manufacturer to use the module. Two types of instructions are required for RF exposure information: (1) to the host product manufacturer, to define the application conditions (mobile, portable xx cm from a persons body); and (2) additional text needed for the host product manufacturer to provide to end users in their end-product manuals. If RF exposure statements and use conditions are not provided, then the host product manufacturer is required to take responsibility of the module through a change in FCC ID (new application). 2.7 Antennas A list of antennas included in the application for certification must be provided in the instructions. For modular transmitters approved as limited modules, all applicable professional installer instructions must be included as part of the information to the host product manufacturer. The antenna list shall also identify the antenna types (monopole, PIFA, dipole, etc. (note that for example an omni-directional antenna is not considered to be a specific antenna type)). For situations where the host product manufacturer is responsible for an external connector, for example with an RF pin and antenna trace design, the integration instructions shall inform the installer that YES Refer to instruction This modular complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. YES Refer to instruction Device is equipped with PCB antenna, Antenna gain 3dBi unique antenna connector must be used on the Part 15 authorized transmitters used in the host product. The module manufacturers shall provide a list of acceptable unique connectors. 2.8 Label and compliance information Grantees are responsible for the continued compliance of their modules to the FCC rules. This includes advising host product manufacturers that they need to provide a physical or e-label stating Contains FCC ID with their finished product. See Guidelines for Labeling and User Information for RF Devices KDB Publication 784748. YES Refer to instruction If the FCC identification number is not visible when the module is installed inside another device, then the outside of the device into which the module is installed must also display a label referring to the enclosed module. This exterior label can use wording such as the following:

Contains Transmitter Module FCC ID:

2BCGR-HS501003 Or Contains FCC ID:

2BCGR-HS501003 2.9 Information on test modes and additional testing requirements5 YES Refer to instruction Additional guidance for testing host products is given in KDB Publication 996369 D04 Module Integration Guide. Test modes should take into consideration different operational conditions for a stand-alone modular transmitter in a host, as well as for multiple simultaneously transmitting modules or other transmitters in a host product. The grantee should provide information on how to configure test modes for host product evaluation for different operational conditions for a stand-alone modular transmitter in a host, versus with multiple, simultaneously transmitting modules or other transmitters in a host. Grantees can increase the utility of their modular transmitters by providing special means, modes, or instructions that simulates or characterizes a connection by enabling a transmitter. This can greatly simplify a host manufacturers determination that a module as installed in a host complies with FCC requirements. 2.10 Additional testing, Part 15 Subpart B disclaimer The grantee should include a statement that the modular transmitter is only FCC authorized for the specific rule parts (i.e., FCC transmitter rules) listed on the grant, and that the host product manufacturer is responsible Any company of the host device which install this modular with modular approval should perform the test of radiated &

conducted emission and spurious emission,etc. according to FCC part 15C :

15.247 and 15.209 &15.207 ,15B Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209

&15.207 ,15B Class B requirementthen the host can be sold legally. YES Refer to instruction Any company of the host device which install this modular with modular approval should perform the test of radiated

& conducted emission and spurious emission,etc. according to FCC part 15C : 15.247 and 15.209

&15.207 ,15B Class B requirement, Only if the test result comply with FCC part 15C : 15.247 and 15.209

&15.207 ,15B Class B requirementthen the host can be sold legally. for compliance to any other FCC rules that apply to the host not covered by the modular transmitter grant of certification. If the grantee markets their product as being Part 15 Subpart B compliant (when it also contains unintentional-radiator digital circuity), then the grantee shall provide a notice stating that the final host product still requires Part 15 Subpart B compliance testing with the modular transmitter installed.6 When the module is installed inside another device, the user manual of the host must contain below warning statements;

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Single Modular approval Declaration letter We Xiamen Zhuoye Technology Co .. Ltd apply single modular approval for Product Name: Bluetooth Module Model: HS5010-03 FCC ID: 2BCGR-HS501003 According to 996369 D01 Module Equip Auth Guide v01r04 and 15.212 requirement:

1) The radio elements must have the radio frequency circuitry shielded. Physical components and tuning capacitor(s) may be located external to the shield, but must be on the module assembly;

Answer Yes shielded . 2) The module must have buffered modulation/data inputs to ensure that the device will comply with Part 15 requirements with any type of input signal;

Answer Yes All inputs to the modules are buffered through logic or microprocessor inputs. 3)The modular transmitter must have its own power supply regulation. Answer Yes A low drop out regulator is used for modular power supply regulation. 4) The module must contain a permanently attached antenna, or contain a unique antenna connector, and be marketed and operated only with specific antenna(s), per Sections15.203, 15.204(b), 15.204(c), 15.212(a), 2.929(b);

Answer Yes Device is equipped with PCB antenna.

(5) The module must demonstrate compliance in a stand-alone configuration;

Answer Yesdistance between modular and all AEs are bigger than 10cm refer to setup photo.

(6) The module must be labeled with its permanently affixed FCC ID label, or use an electronic display (See KDB Publication 784748 about labeling requirements);

Answer Yes The modular has a permanent fixed label, and below statement was listed in the User Manual; The host device must be labeled to display the FCC ID of the module Contains FCC ID: 2BCGR-HS501003

(7) The module must comply with all specific rules applicable to the transmitter includingall the conditions provided in the integration instructions by the grantee;

Answer Yes The module comply with all specific rules applicable to the transmitter including all the conditions provided in the integration instructions by the grantee, Refer to test report and user manual .

(8) The module must comply with RF exposure requirements Answer Yes Transmitter meets MPE calculation of 47 CFR 1.1307 . Refer to MPE Reports and Refer to modular installation manual Please contact me if you have any further questions. Thanks for your attention. Best Regards,

<Signature>

Name: Mingling Sun Title: manager Applicant Company: Xiamen Zhuoye Technology Co .. Ltd

Xiamen Zhuoye Technology Co., Ltd. Covered Equipment Certification Attestation Letter DATE: 2023/08/22 Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046 USA ATTN.: manager FCC ID:2BCGR-HS501003 Xiamen Zhuoye Technology Co., Ltd.(the applicant) certifies that the equipment for which authorization is sought is not covered equipment prohibited from receiving an equipment authorization pursuant to section 2.903 of the FCC rules. Note: If the equipment for which the applicant seeks authorization is produced by any of the entities identified on the current Covered List, the applicant should include an explanation on why the equipment is not covered equipment. Xiamen Zhuoye Technology Co., Ltd.(the applicant) certifies that, as of the date of the filing of the application, the applicant is not identified on the Covered List as an entity producing covered equipment. Signed:

Printed name:MingLing Sun ning L ng Sun Title:manager Company Name:Xiamen Zhuoye Technology Co., Ltd. Date: 2023/08/22

Attestation Statements

(date)2023/9/1 TO: Federal Communications Commission Authorization and Evaluation Division 7435 Oakland Mills Road Columbia, MD 21046, USA RE: Attestation Statements Part 2.911(d)(7) request for (FCC ID2BCGR-HS501003)

(Xiamen Zhuoye Technology Co., Ltd. ), the undersigned, hereby authorize

(Baihetian Innovative Solutions) to act as our designated U.S. agent for service of process, (Xiamen Zhuoye Technology Co., Ltd.) accepts to maintain an agent for no less than one year after the grantee has terminated all marketing and importation or the conclusion of any Commission-related proceeding involving the equipment.

(Baihetian Innovative Solutions) accepts the responsibility to act as designated U.S. agent for service of process. Applicant Information Company name:Xiamen Zhuoye Technology Co., Ltd. Contact Name:MingLing Sun Address:Unit 602, No. 21 Pingcheng North Road, Haicang District, Xiamen, FujianProvince FRN: 0034122010 Telephone No:

Email: 3487705339@qq.com 13959228749 Signature

[name]

U.S. Agent Information:

Company Name:Baihetian Innovative Solutions Address:6837 Chase Rd Dearborn, MI 48126 FRN:0033401605 Contact Name:Kenneth Young Telephone No:313-395-3113 Email:ken.young@baihetiansolutions.com Signature

[name]