XT6075 User Guide Terminology a) Unit Xirgo XT6075 b) Asset Customer product that the XT6075 is mounted to. 1. XT6075 Installation:
Install unit bracket a) b) Secure unused high voltage communication connector into unit bracket c) Install unit into bracket Push unit into bracket Secure 2 torx screws Push On/Off Switch d) Connect antenna wires to unit e) Connect 3 and 7 pin connectors to unit f) Bundle the wires by using cable ties and fix to unit g) Connect unit ribbon harness to controller XT6075 User Guide h) Attach TK bracket to unit i) Fit unit with bracket to TK controller and tighten upper screws j) Connect antenna wires to unit k) Connect Power Cable Harness X1 RED wire to Transformer X1 tap, and X2 BLACK wire (with ground terminal) to Controller Chassis. l) Connect 7 pin from unit ribbon harness to unit m) Connect 3 pin harness to unit n) Bundle the wires by using cable ties and fix to unit Test:
XT6075 User Guide o) Connect power plug to power source p) Put unit into install mode (on/off button) see section below q) Observe installer LED for green pass see section below r) s) Take unit out of installer mode t) Close the controller door. u) If installer LED fail, refer to trouble shooting guide and fix issue Installation is complete. LED Operation 1. GPS LED (Green):
OFF GPS OFF Blinking GPS Lock (position obtained) ON solid No GPS Lock 2. Asset LED (Red, disabled during install mode):
OFF Asset OFF Slow blink Asset communications OK Med blink Physical connect on 7 pin but no asset communications Fast blink No physical connect on 7 pin ON solid software upload in progress 3. CELL LED (Blue):
OFF Scanning for network or cell module is off Blinking Registered on cellular network ON solid Periods of network data transmission active 4. WLAN LED (Orange, disabled during install mode):
OFF - Mesh OFF Slow blink Mesh Bound Fast blink - Mesh searching for network ON solid - No battery detected 5. INSTALL LED To use the INSTALL LED, use the following steps:
a. Enter Install mode i. Make sure unit is powered on by applying asset AC or by pressing the unit ON/OFF button (the unit is on when the GPS LED is flashing or on solid green). ii. Press and hold ON/OFF button until INSTALL LED is blinking blue then release iii. Wait for unit to reboot, indicated by fast blinking green LED b. Observe INSTALL LED i. Testing in progress is indicated by fast blinking green LED (approx. 1-6 min) ii. Testing is complete when solid LED is observed:
Solid GREEN: All test conditions PASS Solid BLUE: No AC & No asset Communications but all others PASS Solid RED: Any other conditions (fails) XT6075 User Guide c. Exiting install mode i. Press and hold ON/OFF button for approx. 5 seconds any time after solid LED indication from step 2 above ii. Or wait for timeout of install mode which is 15 minutes from start of solid LED status Important notes about the INSTALL LED and install mode:
1. INSTALL LED is only operational when the unit is put into the install mode. It does not provide information during normal operation. 2. The INSTALL LED and the install mode do not work during off power reporting periods
(periodic, listen, motion start/motion stop). 3. Install mode will disable normal unit communications with the asset and the server and the following conditions will exist:
a. No SMS processing. b. No processing of forward commands from the server to the unit. c. No LED status function on the WLAN or ASSET LEDs during install mode. 4. During the install mode testing, the unit will check for the following:
a. AC power is on b. Unit is communicating with asset c. Unit has communicated with server d. Physical connection detected on the 7 pin connector e. Battery is detected f. GPS position obtained g. 2G/3G/4G cellular registration and activation is good General Notes LED Blink Rates:
Slow Blink once per three second period Med Blink once per second Fast Blink three times per second ON/OFF Push Button:
U OFF and not on AC power o press ON/OFF Push Button to wake unit (1 sec then release) o unit will wake for 15 minutes before shutting down (no AC) Unit ON and not on AC power or Install Mode o press and hold for > 15 seconds to initialize unit ship mode shut down XT6075 User Guide Regulatory Statements:
FCC:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1)
(2) this device may not cause harmful interference, and this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Xirgo Technology may void the FCC authorization to operate this equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Connect the equipment into an outlet on a circuit different from that to which the receiver is Increase the separation between the equipment and receiver. connected. Consult the dealer or an experienced radio/TV technician for help. Radiofrequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 30 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. IC:
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le onctionnement. XT6075 User Guide Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful communication. Conformment la rglementation d'Industrie Canada, le prsent metteur radio peut fonctionner avec une antenne d'un type et d'un gain maximal (ou infrieur) approuv pour l'metteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope rayonne quivalente (p.i.r.e.) ne dpasse pas l'intensit ncessaire l'tablissement d'une communication satisfaisante. This radio transmitter (IC: 10281A-XT6075, Model Number: XT6075) has been approved by Industry Canada to operate with the antenna types listed below with the maximum permissible gain and required antenna impedance for each antenna type indicated. Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited for use with this device. Cet metteur radio (identifier le priphrique par numro de certification, ou le numro de modle si Catgorie II) a t approuv par Industrie Canada pour fonctionner avec les types d'antennes numres ci-dessous avec le gain maximal admissible et l'impdance d'antenne requise pour chaque antenne type indiqu. Types d'antennes ne figurent pas dans cette liste, ayant un gain suprieur au maximum gagner indiqu pour ce type, sont strictement interdites pour une utilisation avec cet appareil. 2G/3G/4G LTE Antenna Specifications
-4.1
-2.6 2.2m 698~960 Connector 1710~2170 2490~2690
-2.47 50 RG58 Low Loss Right-Angle FAKRA Code D-female Frequency (MHz) Average Gain (dBi) Impedance Cable type Cable length The DOC (Declaration of Conformity) is either included in the packaging or can be found at the following link: www.xirgotech.com 2.4GHz Wi-Fi Antenna Specifications 2400~2500 Impedance Cable type Cable length Frequency (MHz) Average Gain (dBi) Right-Angle FAKRA Code B-female RG58 Low Loss
-3.65 50 Connector 2.2m