XT-1010 User Guide Model: XT-1010 FCC ID: GKM-XT1000 IC: 10281A-XT1000 Version 1.1 1 2. Hardware Description .............................................................................................5 Table of Contents Document Change History ..........................................................................................3 1. Introduction ...........................................................................................................4 1.1FeatureMatrix.................................................................................................................................................................................4 2.1 Hardware Specifications.............................................................................................................................................................6 2.2 Cable Harness Description.........................................................................................................................................................6 2.3 LED Description..............................................................................................................................................................................7 3.1 Screw Mounting..............................................................................................................................................................................7 3.2 Magnetic Mounting........................................................................................................................................................................8 3.3 VHB Tape Mounting......................................................................................................................................................................8 4.1Device Installation.........................................................................................................................................................................9 4.2 Pairing the XT1010Z and the XT4860G5...........................................................................................................................10 4.3 Unpairing Devices........................................................................................................................................................................10 4. Quick Start Guide....................................................................................................9 3. Device Mounting Options: ......................................................................................7 2 Document Change History Revision 1.0 1.1 Date 8/28/2014 9/2/2014 Author Johnny Chen Johnny Chen Changes Document Creation Revision Based on Naders Feedback 3 1.1 Feature Matrix 1. Introduction The XT-1010 isawirelessZigBeesensor that pairs with theXT-4860G5generally knownas the Base Unitto provide inclinationdata based on a 3-axis digital accelerometer readout with an accuracy of 1 degree.Additional general purpose digital IO sensors can also be queried andtransmittedtothe XT-4860G5.The XT-1010 leveragesahigh efficiencysolarenergy harvestingplatformtosupportlong term, remote deployments withoutthe burden offrequent battery replacement. Thisinstallation guidedescribes the physical hardware, associated parts,mounting options, anda quick start-up procedure. High Efficiency Solar Panel 6600mAhRechargeableLi-Ion Battery Diagnostic LEDs OptionalDigital IO Sensorsand 1-Wire Serial Bus ZigBee pairing with XT-4860G5 Inclinometer Databased on 3-axis Dig Accel. with 1 deg. accuracy Over-the-airFWupgrade via XT-4860G5 Feature Description XT-1010 4 2. Hardware Description Belowis a depiction of key interfaces of the XT-1010:
Device Label ZigBee Pairing Button Solar Panel LED Indicators 8-Pin Bayonet Connector An optionalCable Harness that interfaces withthe unit is shown below. The Cable provides external power, when available, as well as interface to the IO HW options 5 2.1 Hardware Specifications ZigBee Specification Technology Frequency Band Antenna gain Transmit power Data Rate Power Requirements D.C. Power (if Avail.) Battery Physical Connection Interface Connector Programming Mechanical Case Material Dimension Weight Operating Temperature Protection Rating ZigBeeIEEE 802.15.4 DSSS modem 2405-2483.5MHz 0.5 dBi (peak again), -0.5 dBi (Average gain) 12dBm/MHz 250 kbps 8-24V, 12 V nominal Internal 6600mAh rechargeable Li-Ion 8-pin Bayonet type Serial (UART Logic Level) ABS plastic with weather-proofing for outdoor use 7.6 X 4.9 X 1.4 18 oz.
-30C to +70C IP67 2.2 Cable Harness Description Pin # Wire Color Pin Name Functional Description Port Characteristic 1 2 3 4 5 6 7 8 Ignition Sense Input port Ground Output Port (Defaulted open circuit) External battery negative terminal White Yellow Black Green IN1 IN2 Ground Out Blue UART-Rx Brown UART-Tx Red Orange VBATT ADC Main battery voltage, DC Analog Input 8v to 24v, Internally pulled low 2.4 to 24V, < 0.2 V Note: Internally pulled high 3.3V Logic Interface Com Port Settings:
Baud rate: 115200 bps; Flow control:
None; 8N1 3.3V Logic Interface Com Port Settings:
Baud rate: 115200 bps; Flow control:
None;8N1 8-24 V, 12V Nom. 8-24 V 6 2.3 LED Description LED GPS(Green) Description Pairing Successful Stand-by for Pairing Status Solidfor 30 Seconds then OFF BlinkingSteadily 3. Device Mounting Options:
3.1 Screw Mounting The XT-1010 canbe mounted via4mountingscrew,2 per side as depicted below. 7 3.2 Magnetic Mounting The XT-1010can also beprovidedwith4pre-installed(or kittedseparately)magnetsas depicted below. 3.3 VHB Tape Mounting Forsemi-permanent mountingoption,the device can be mounted with 3MVHB tapeas shown below. 8 4. Quick Start Guide 4.1 Device Installation The XT1010(Sensor unit)pairs with the XT-4860G5(Baseunit)and provides inclinometer data based on the on-board 3-axis digital accelerometer outputwhich in turn is transmitted toend user Server over the cellular network.The proper installation of the unit is criticaltoacquiring accurate inclinometer data.An application note entitled Installing and Pairing the XT-4860 and XT-1010 for Wireless Inclinometer Functionality contains detailed instructions for installing and pairing the two devices. This quick start guide will give you basic steps for installation and pairingof the two devices.Refer to the application note for any additional detail and instructions. When installing the device,make sure the Base unit(XT-4860G5)faces the Sensorunit (XT-1010) EachUnit hasa label near the 8-pin Connector to show the directionof deviceinstallation. The Base and the Sensor must be on the same plane and facing each otherfor optimal performance. The picture below illustrates theidealorientation of thetwo devices R O S N E S E C A F F A C E B A S E U N I T As anexample,below depicts possiblemounting positions of the two Units for aman-lift application. 9 4.2 Pairing the XT1010Z and the XT4860G5 WithbothBase andSensor unitsproperly oriented,the pairing process of the two devices can begin. Note that only one Sensor unit can be pairedwith one Base unit.During the pairing process, the devicesarecalibrated and normalized relative to each other.Once the calibration is complete, the Devices must not be moved or repositioned. Tobegin the pairing process,pressthe blackbuttonlocatednear the circular connector on the side of theBase unitfor5seconds. You should see theamberLED light(marked with Z)flashing 4 times per second.ThisLED pattern signifies that the Base unit is searching for the Sensor unit that itismeantto pair with. There is a 60-second window for the pairing process to complete. If the pairing process was not successful within 60 seconds, then the unit will return to its configured normal state and the process needs to berepeated if pairing isstill needed.At any time during pairing, the process can be stopped or reset by pressing and holding the button on either device for 15 seconds, then releasing, or by simply waiting for a timeout. Pairing Button During the Base unit60-secondpairingtime, press andhold the pairing button on the Sensor unit for 5 seconds. The green LED(marked with a C)will flash4 times per secondas well.A typical pairing process takes about 3to5 seconds afterpressingthe pairing buttonsofboth Units. After successful pairing, theBase units orange LED will turn off and the Sensor units green LED will turn solid for 30 seconds, thenitwill turn off. After the pairing process,theSensor unit will automatically send inclinometer data to the base unit ata rate of 1 sample per 5 seconds. Toun-pairaset ofpairedXT-4860 and XT-1010devices, press and hold the button on the XT-
4860 device for 15 seconds, then release. That devicewill attempt to notify its XT-1010 pair of the pairing reset. There is no LED feedback for a pairing reset. Thepairingreset can be performed individually on an XT-4860 or XT-1010 device if the paired device is no longer present. 10 4.3 Un-pairing Devices FCC/IC:
REGULATORY COMPLIANCE INFORMATION This equipment with FCC-ID: GKM-XT1000 and IC: 10281A-XT-1000, Model: XT-1010 is subject to the Federal Communications Commission (FCC) and Industry Canada (IC) rules. NOTICE:
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with Part 15 of the FCC Rules and with license exempt Radio Standard Specifications of Industry Canada. Operation is subject to the following two conditions:
(1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation. Les changements ou modifications non expressment approuvs par la partie responsable de la conformit pourraient annuler l'autorit de l'utilisateur utiliser l'quipement. Le prsent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation est autorise aux deux conditions suivantes :
(1) l'appareil ne doit pas produire de brouillage, et
(2) l'utilisateur de l'appareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible d'en compromettre le onctionnemen Radio frequency radiation exposure Information:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. 11
