XVA-CBL-IOX-01 INSTALLATION GUIDE Interface Cable DOC. 1013A | 04/2026 Xirgo and the Xirgo logo are either trademarks or registered trademarks of Xirgo Holdings, Inc. in the United States and/or other countries. Geotab, Geotab GO, and MyGeotab are either trademarks or registered trademarks of Geotab, Inc. in the United States and/or other countries. Other trademarks, registered trademarks, and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Xirgo disclaims any proprietary interest in the marks and names of others. Xirgo is not responsible for errors in typography or photography. 2026 Xirgo Holdings, Inc. TABLE OF CONTENTS Introduction Safety Checklist Hardware Description Specifications Hardware Hookup Connect the Cable to the Dashcam Connect the Cable to the Geotab IOX Ecosystem Termination Shunt Safety Advice Regulatory Information FCC Warning: California Proposition 65 IC Hardware and Software Versions 1 2 3 4 5 5 5 6 7 8 8 8 9 9 Contents i XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A INTRODUCTION The XVA-CBL-IOX-01 is an interface cable for use with a Xirgo dashcam and a Geotab GO device. The cable transmits vehicle video telematics from the Xirgo dashcam to the Geotab GO device for use in the MyGeotab platform. Page 1 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A SAFETY CHECKLIST WARNING: Installation should be performed by a qualified individual or installation professional only. Working with a vehicles power system can be dangerous to both you and your vehicle. Since vehicle designs and power/input sources can vary from vehicle to vehicle, the procedures described here are intended as a guide only. Personal Protection Equipment: To prevent injury, please wear the following equipment at all times when working on or near the vehicle. Hardhat Steel toe shoes High visibility vest Eye protection Site Requirements: Place the vehicle on a flat surface in an area that is sheltered from weather
(rain, snow, wind, etc.). Page 2 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A HARDWARE DESCRIPTION XVA-CBL-IOX-01 parts Molex connector to Xirgo dashcam Expansion port to other IOX devices
(shown with termination shunt) IOX connector to GO9 device or other IOX devices Page 3 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A SPECIFICATIONS Specification Functionality Weight Length Interfaces Description Universal RS232-type cable 1.8 ounces (50 grams) 49.6 in. (1260 mm) CAN: 500 kb/s; for daisy chaining RS232 Male/Female: 300 to 115,200 baud, parity, data bits, and flow control RS232 Male/Female: 8 data bits, and 1 stop bit Nominal Input Voltage 12/24 VDC Maximum continuous current to the IOX in daisy chain 40 mA at 12 V / 24 VDC Operating mode (typical/nominal current draw) Maximum peak current to the IOX in daisy chain 2750 mA @ 12 V/24 VDC Connectors Male Mini-USB Type-B connector: Daisy chain power and CAN in Note: For each IOX in the daisy chain, add the maximum current draw, and do not exceed the maximum total IOX current draw. Female Mini-USB Type-B connector: Daisy chain power and CAN out 5-Pin Molex 50579705 with the following pinouts:
1. GND (Black) 2. RS232 Tx (Green) 3. RS232 Rx (Yellow) 4. KL15 (White) 5. Power (Red) Compatible Devices All GO9 and newer devices and variants with firmware x.45.28 or later Page 4 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A HARDWARE HOOKUP Connect the XVA-CBL-IOX-01 to the Xirgo dashcam and the Geotab device. Connect the Cable to the Dashcam Connect cable to Xirgo dashcam Connect the Cable to the Geotab IOX Ecosystem The device can connect directly to the Geotab GO device or daisy chain to the expansion port of another IOX cable already connected to a Geotab GO device. Connect the Cable to a GO Device If connecting the XVA0CBL-IOX-01 directly to a Geotab GO device, and no other devices are to be connected, perform the following. 1. Connect the cable to the IOX port on the side of the Geotab GO device. 2. Connect the termination shunt to the cables expansion port. For details, refer to Termination Shunt on page 6. Daisy Chain the XVA-IOX-101 to another IOX Cable If daisy chaining the XVA0CBL-IOX-01 to an existing IOX connection, perform the following. 1. If a termination shunt is installed on the connected cables expansion port, remove it from the cable. 2. Connect the XVA-CBL-IOX-01 to the expansion port on the connected devices cable. Page 5 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A 3. Use a cable tie to secure the XVA-CBL-IOX-01 to the expansion port. Termination Shunt The XVA-CBL-IOX-01 cable is capable of daisy chaining to other devices in the IOX ecosystem; creating a network of in-
vehicle devices connected to the MyGeotab platform through a Geotab GO device. Remove the Termination Shunt The XVA-CBL-IOX-01 cable is equipped with a removable termination shunt that must be removed from the cables expansion port if the cable is to connect to other IOX cables. Once the connection is made, secure the connector to the expansion port with the included cable tie. Daisy-chained device installed Install the Termination Shunt If the cable is not going to be connected to other IOX cables, the termination shunt must be installed on the cables expansion port to ensure communication amongst the connected devices. Termination shunt installed Page 6 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A SAFETY ADVICE Caution This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Caution Any changes or modifications (including the antennas) to this device that are not expressly approved by the manufacturer may void the users authority to operate the equipment. Page 7 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A REGULATORY INFORMATION FCC This equipment with FCC ID: GKM-XVA-IOX Subject to the Federal Communications Commission (FCC) and Industry Canada (IC )rules. Notice:
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, 2. This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications made to this equipment not expressly approved by Xirgo Technologies, LLC may void the FCC authorization to operate this equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna. 2. Increase the separation between the equipment and receiver. 3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. 4. Consult the dealer or an experienced radio/TV technician for help. Radio frequency radiation exposure information:
Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Warning: California Proposition 65 This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This device and its antenna must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. Page 8 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A IC IC: 10281A-XVAIOX Antenna Statement Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type and its gain should be so chosen that the Equivalent Isotropically Radiated Power (E.I.R.P.) is not more than that necessary for successful communication. Conformment la rglementation dIndustrie Canada, le prsent metteur radio peut fonctionner avec une antenne dun type et dun gain maximal (ou infrieur) approuv pour lmetteur par Industrie Canada. Dans le but de rduire les risques de brouillage radiolectrique lintention des autres utilisateurs, il faut choisir le type dantenne et son gain de sorte que la Puissance Isotrope Rayonne quivalente (P.I.R.E.) ne dpasse pas lintensit ncessaire ltablissement dune communication satisfaisante. License exempt This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
1. This device may not cause interference, 2. This device must accept any interference, including interference that may cause undesired operation of the device. Le prsent appareil est conforme aux CNR dIndustrie Canada applicables aux appareils radio exempts de licence. Lexploitation est autorise aux deux conditions suivantes:
1. Lappareil ne doit pas produire de brouillage, et 2. Lappareil doit accepter tout brouillage radiolectrique subi, mme si le brouillage est susceptible den compromettre le fonctionnement. Hardware and Software Versions HW Version: XVA-IOX-001 SW Version: XVA-IOX-001 Page 9 XVA-CBL-IOX-01 / INSTALLATION GUIDE DOC # 1013A XVA-CBL-IOX-01 INSTALLATION GUIDE DOC. 1013A / PUBLISHED 04/2026 xirgo.com 2026 Xirgo Technologies. All Rights Reserved.
