FCC ID: HE7TGL Tag Link

by: Xmark Corporation latest update: 2003-09-26 model: TGL

Two grants have been issued under this FCC ID on 09/26/2003 (this is one of six releases in 2003 for this grantee). Public details available include internal & external photos, manuals, and frequency information. some products also feature user submitted or linked drivers, troubleshooting guides, warrantee terms, password defaults, & instructions.

permalink for this FCC identifier

search for: Repair details

from iFixIt

Trade-in? Recycling locations

eg for Slack usage

all	frequencies		exhibits	applications
		manual

all exhibits 7
1 ~ 2003-09-26 7
2 ~ 2003-09-26 7

app s				submitted / available
1 2	User Manual	Users Manual	pdf	1.26 MiB
1 2		External Photos	pdf
1 2		ID Label/Location Info	pdf
1 2		Internal Photos	pdf
1 2		Cover Letter(s)	pdf
1 2		Test Report	pdf
1 2		Test Setup Photos	pdf

exhibit
download
text

1 2

User Manual

Users Manual

pdf

1.26 MiB

User Manual - INTRODUCTION PHOTO ILLUS: TAG LINK WITH PTAG TAG LINK The eXI Tag Link device automates tag administration by providing a localized eLink between the Halo or Assetrac application software and the targeted tag device. The Tag Link communicates directly with the system computer through a serial port and may be powered by an internal 9 volt battery or accessory AC wall adapter. The Tag Link enables the software application to transparently interact with the tags. Tag Link Views PHOTO ILLUS: TAG LINK WITH MOTHER TAG WITH LED HIGHLIGHTED Copyright 2003 - eXI Wireless Systems Inc. Page XX 980-000003 002. R1.01 User Manual - INTRODUCTION Tag Link Range The communication range for Tag Link is designed to be typically less than 12 inches. Therefore, it is recommended that the tags be located within 6 to 12 inches of Tag Link. Those tags with off body sensor must be placed on the front panel in the marked area. This will assure that the alarm TIC message is not transmitted. Tag Link Functions The following table lists the functions that are performed transparently in response to commands from the application software:

COMMAND Power Up Power Down TAG LINK ACTION Powers up from sleep mode Return to sleep mode immediately or after 30 seconds if no application command LED none none Check RF Noise Measures and reports interference at 307 kHz Measures and reports interference at 433.92 MHz Test Tag TIF Interrogates tag and returns ID and tag status Green Flashes Red Flashes See next table Test Tag TIC Tag Link waits for TIC signal from specified tag See next table Set TLM Tag Link issues eLink TLM set command Disable TLM Tag Link issues eLink TLM disable command See next table See next table Check TLM Tag Link queries tag and reports rate to application See next table Assign MTAG Reads Mother Tag ID and assigns dynamic ID MTAG Bond Sends baby tag ID(s) to Mother Tag, Mother Tag is then bonded to the assigned tag(s) See next table See next table Each operation is performed for a maximum of 10 seconds. During application the following audio-visual signals are output:

ACTION Command received BEEPER Very short beep Command succeeded Longer beep Command failed 4 short beeps LEDs None random Both briefly on Copyright 2003 - eXI Wireless Systems Inc. Page XX 980-000003 002. R1.01 Restricted Rights User Manual - SUPERVISOR eXI's commercial software and commercial computer software documentation is provided to United States Government agencies in accordance with the terms of this Agreement, and per subparagraph "(c)" of the "Commercial Computer Software - Restricted Rights" clause at FAR 52.227-19 (June 1987). For DOD agencies, the restrictions set forth in the

"Technical Data-Commercial Items" clause at DFARS 252.227-7015 (Nov 1995) shall also apply. FCC Regulations This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for Class B Digital Device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures. Any changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio/TV technician for help eXI Wireless Systems CANADA: 287710217261A

* This device complies with Part 15 of the FCC Rules. Operation is subject to the following two rules: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Model No.: Tag Link FCC ID: HE7TGL Made in Canada Copyright 2003 - eXI Wireless Systems Inc. Page 137 980-000003 002. R1.01

		frequency	equipment class	purpose
1	2003-09-26	433.92 ~ 433.92	DSR - Part 15 Remote Control/Security Device Transceiver	Original Equipment
2		0.307 ~ 0.307	DCD - Part 15 Low Power Transmitter Below 1705 kHz

Application Forms

app s	Applicant Information
1 2	Effective	2003-09-26
1 2	Applicant's complete, legal business name	Xmark Corporation
1 2	FCC Registration Number (FRN)	0007050206
1 2	Physical Address	309 Legget Drive
1 2		Kanata, N/A K2K 3A3
1 2		Canada

app s	TCB Information
1 2	TCB Application Email Address	m******@ccsemc.com
1 2	TCB Scope	A1: Low Power Transmitters below 1 GHz (except Spread Spectrum), Unintentional Radiators, EAS (Part 11) & Consumer ISM devices

app s	FCC ID
1 2	Grantee Code	HE7
1 2	Equipment Product Code	TGL

app s	Person at the applicant's address to receive grant or for contact
1 2	Name	C**** B****
1 2	Title	Senior RF Designer
1 2	Telephone Number	613-5******** Extension:
1 2	Fax Number	613-5********
1 2	E-mail	c******@xmark.com

app s	Technical Contact
		n/a

app s	Non Technical Contact
		n/a

app s	Confidentiality (long or short term)
1 2	Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	Yes
1 2	Long-Term Confidentiality Does this application include a request for confidentiality for any portion(s) of the data contained in this application pursuant to 47 CFR § 0.459 of the Commission Rules?:	No
	if no date is supplied, the release date will be set to 45 calendar days past the date of grant.

app s	Cognitive Radio & Software Defined Radio, Class, etc
1 2	Is this application for software defined/cognitive radio authorization?	No
1 2	Equipment Class	DSR - Part 15 Remote Control/Security Device Transceiver
1 2	Equipment Class	DCD - Part 15 Low Power Transmitter Below 1705 kHz
1 2	Description of product as it is marketed: (NOTE: This text will appear below the equipment class on the grant)	Tag Link
1 2	Related OET KnowledgeDataBase Inquiry: Is there a KDB inquiry associated with this application?	No
1 2	Modular Equipment Type	Does not apply
1 2	Purpose / Application is for	Original Equipment
1 2	Composite Equipment: Is the equipment in this application a composite device subject to an additional equipment authorization?	Yes
1 2	Related Equipment: Is the equipment in this application part of a system that operates with, or is marketed with, another device that requires an equipment authorization?	No
1 2	Is there an equipment authorization waiver associated with this application?	No
1 2	If there is an equipment authorization waiver associated with this application, has the associated waiver been approved and all information uploaded?	No

app s	Test Firm Name and Contact Information
1 2	Firm Name	Compliance Certification Services Inc
1 2	Name	S** C****
1 2	Telephone Number	408-4******** Extension:
1 2	Fax Number	408-4********
1 2	E-mail	s******@ccsemc.com

Equipment Specifications
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
1	1	15.231(e)		433.92000000	433.92000000
	Line	Rule Parts	Grant Notes	Lower Frequency	Upper Frequency	Power Output	Tolerance	Emission Designator	Microprocessor Number
2	1	15C		0.30700000	0.30700000

some individual PII (Personally Identifiable Information) available on the public forms may be redacted, original source may include additional details