FCC ID: 2AVMJ-XGO2 Kids Smartwatch

 

Kid Smart watch User Manual

Focus on Smart Kid’s device, Follow Kid’s demand, Care about children’s

Education, Ensure Children’s safety

AI voice by iFLY

Please read the user manual carefully before using, so that you

can install it correctly and use it quickly. The color of the

product shall be subject to the actual product

Watch

1pcs

User manual 1set

Packaging accessories

Charging

cable

Screwdriver

1pcs

1pcs

Card

Protective

film

Specifications

Name: Kids Smartwatch

Battery: Lithium polymer 3.8V

Input charging: DC5V 1A

Working temperature: 0℃--35℃

Relative humidity: Non-condensing condition 5%--93%

1 Preparation before use

Check whether the model of the equipment is correct and whether the accessories are

Select the nano SIM card of, 4G network, and refer to the opinions of dealers for details.

(please POWER-OFF before installing the card)

The watch SIM card needs to activate GPRS function and call display function.

Install the app client on the mobile terminal. For details of the client, please ask your dealer

Barcode

complete.



2 Install nano SIM card

Select the nano SIM card of 2G \ 4G network. This card needs to open the call display, GPRS

data for Internet and call function. Note that the SIM card should be installed and then turned on

when the power is turned off to prevent the SIM card from being burned out.

3 Install SIM card

Install SIM card in power-off status

Note: remove the card plug to install the card. Avoid to water

inside please tighten the screw on the card plug.Otherwise it

will cause the watch to be unable to use normally

After installing the SIM card, press the figure above to install the SIM card trim in place, and then

press and hold the power-key to start the phone.

4 Power-off

Power-off: the watch can only be remote to power-off through the app or enter the setting

interface in the normal working state. If the watch is not installed with card or connected with app,

you can enter the setting interface to power-off. Take care not to remove the SIM card directly

when it is turned on to prevent the card from burning.

5 Watch information

Front camera

Front camera

Flight

SIM card

slot

Back-key

Power-key/SOS key

Button operation instruction

Power-key: When the watch is off, Long time press and hold the power-key

to power on

The watch is connected to Internet when it is turned on and the app has

set the SOS number. Long press and cycle to dial three numbers. If there

is no answer, cycle to dial twice.

Back key: short press to return to the previous interface

USB connector

6 Download APP

6.1 Scan QR code to download watch app DOWEAR 2. App QR code can also be found in watch

app download interface.

6.2 Register and Log-in

Create a Account and Log-in under the APP instruction

6.3 App account binding watch device

After the account registration is successful, bind the watch, scan the registration QR code pasted

on the watch or manually input the 15 digit registration code. If the registration barcode pasted on

the watch is lost, you can also find the registration code in the watch app download interface.

Then go to binding settings.



7 Function Instruction

Base station, GPS, WiFi Positioning: view real-time location by App map

Weather forecast: watch can automatically update weather information

Footsteps: Record history tracks

Safety area: We can set three safety fences , and there will it will alarm when out of the

fence.

Alarm: can set 3 alarm clocks

Phonebook: can set 15 contact phone numbers.

Chat: Click to chat with app, and send voice and picture to mobile phone. Note: the watch

cannot send micro information to the mobile app, which can send micro information to the watch.

Camera: take photo/video/or turn-on camera automatically by open the back case.

Dialing: watch can dial independently, app can turn on or off this function

Video call: click in to select single chat or group chat to have video chat with app, and group chat

can be up to 8 people together.

Gallery: Enter to review the photos taken by the watch. Photos can be shared, deleted and

modified.

Settings: volume settings (media volume, alarm volume, ringing tone volume, call volume)

Brightness setting, sleep, restart, shutdown, device information (wireless upgrade, model, version

number, IMEI)

Desktop style (single palace, four Palace), cleaning tools (cleaning background applications,

cleaning cache)

More (Bluetooth, flashlight, mobile network, date and time settings, language).

Barcode

app.

Early Education

1、Comment: click in and click "start" in the interface to start the game. The difficulty of

the game is divided into three levels: simple, general and difficult. Click the setting button in the

interface to set.

Touch to make friends: Click to enter the interface. Touch two watches to make friends. After

making friends successfully, the picture will light up.

It can make four friends maximum. Click your friend's Avatar to chat with your friend, and send

voice and pictures to your friend. Long press messages sent by friends to delete and delete all.

Long press "friends picture" to delete friends.

and other third-party applications, which can be installed by issuing installation instructions on the

app.

SOS: Set 3 emergency contact numbers. In case of emergency, the watch will press and hold the

SOS key for 3 seconds, then it will give an alarm and call 3 numbers in a circle. When there is no

answer, the cycle of dialing ends in two rounds.

Voice monitoring: through app settings, the watch actively dials the set number (generally the

1. Scan code to download: Click to display QR code, scan code to download DOWEAR

2、Pocket story: enter to listen to children's stories.

2、CID code: confirm the register number



parent number), and the mobile phone can realize one-way listening to the watch end

Non-disturbed time: three time periods can be set. The watch can block all phones and other

sounds during the time period (valid from Monday to Friday).

SMS reminder setting: it can control whether the watch opens the SMS function of relevant

alarm information (normal charging for SMS)

Family member: display all family member accounts which bound

Remote shutdown: the watch can be remote to power-off through app after it is turned on and

working normally.

8 Troubleshooting

The watch cannot be connected to the server when it is turned on at the

first time. The app sends an instruction to show that the device is not

connected to the Internet. Please check:

1)Check SIM card is from mobile card, Unicom card or telecom card.

2)Check if it activate the internet data

3)The server parameters are IP and port. If the IMEI is correct, the IMEI barcode

pasted on the watch must be consistent with the IMEI written by the watch factory.

If you don't understand, you can ask the agent.

5）There are two situations when registering: A. prompt that the equipment number does not exist

or that the equipment number has been registered, and you must find an agent to handle it; B.

prompt that the account number has been registered, that is, the account number has been

registered, and the customer only needs to change an account number to register again.

FCC Statement

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could

void the user's authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital

device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable

protection against harmful interference in a residential installation. This equipment generates uses

and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no

guarantee that interference will not occur in a particular installation. If this equipment does cause

harmful interference to radio or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information:

This device meets the government's requirements for exposure to radio waves. The guidelines are

based on standards that were developed by independent scientific organizations through periodic

and thorough evaluation of scientific studies. The standards include a substantial safety margin

designed to assure the safety of all persons regardless of age or health. FCC RF Exposure

Information and Statement the SAR limit of USA (FCC) is 1.6 W/kg averaged over one gram of

tissue. Device types: This device has also been tested against this SAR limit. This device was

tested for typical body-worn operations with the back of the device kept 10mm from the body. To

maintain compliance with FCC RF exposure requirements, use accessories that maintain an 10mm

separation distance between the user's body and the back of the device. The use of belt clips,

holsters and similar accessories should not contain metallic components in its assembly. The use

of accessories that do not satisfy these requirements may not comply with FCC RF exposure

requirements, and should be avoided.



IC Statement

- English:

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) This device may not cause interference,

and (2) This device must accept any interference, including interference that may cause undesired

operation of the device.

The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).

- French:

Le présentappareilestconforme aux CNR d'Industrie Canada applicables aux appareils radio

exempts de licence. L'exploitationestautorisée aux deux conditions suivantes:

(1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareildoit accepter tout

brouillageradioélectriquesubi, mêmesi le brouillageest susceptible d'encompromettre le

fonctionnement.

IC RF Exposure Information

This equipment complies with IC radiation exposure limits set forth for an uncontrolled

environment and meets RSS‐102 of the IC radio frequency (RF) Exposure rules. This equipment

has very low levels of RF energy that are deemed to comply without testing of specific absorption

ratio (SAR).

Cet équipement est conforme aux limites d’exposition aux rayonnements énoncées pour

un environnement non contrôlé et respecte les règles d’exposition aux fréquences radioélectriques

(RF) CNR‐102 de l’IC. Cet équipement émet une énergie RF très faible qui estconsidérée

conforme sans évaluation du débit d’absorption spécifque (DAS).



 

 

 

 

 

 

 

 

 

 

SHENZHEN LCS COMPLIANCE TESTING LABORATORY LTD. FCC ID: 2AVMJ-XGO2 IC: 26094-XGO2 LABEL AND LOCATION Kids Smartwatch Model: XGO2 FCC ID: 2AVMJ-XGO2 IC : 26094-XGO2 HVIN : XGO2 Size: L 2.0cm*W2.0cm Label Location This report shall not be reproduced except in full, without the written approval of Shenzhen LCS Compliance Testing Laboratory Ltd. Page 1 of 1

 

 

XPLORA Technologies AS Agent Authorization Company: XPLORA Technologies AS Address: Tangerudvegen 13, Fjerdingby, 2008, Norway Product Name: Kids Smartwatch Trade Mark: XPLORA Model Number: XGO2 FCC ID: 2AVMJ-XGO2 We authorize MiCOM Labs Inc., 575 Boulder Court, Pleasanton, California 94566, USA, to act on our behalf on all matters concerning the certification of above named equipment. We declare that MiCOM Labs Inc. is allowed to forward all information related to the approval and certification of equipment to the regulatory agencies as required and to discuss any issues concerning the approval application. Any and all acts carried out by MiCOM Labs on our behalf shall have the same effect as acts of our own. Signature:

Date: 2021-07-23 Name:

Sanghyo Kim Title:

CTO Company: XPLORA Technologies AS

 

 

 

 

 

 

 

 

 

 

XPLORA Technologies AS

Office of Engineering Technology

Federal Communications Commission

7435 Oakland Mills Road

Columbia, MD 21046

USA

Date: 2021-07-23

Subject; Request for Confidentiality

FCC ID: 2AVMJ-XGO2

To Whom It May Concern,

Pursuant to the provisions of the Commission’s rules Title 47 Sections §0.457 and §0.459, we

are requesting the Commission to withhold the following attachment(s) as confidential

documents from public disclosure indefinitely.

These documents contain detailed system and equipment descriptions and are considered as

proprietary information in operation of the equipment. The public disclosure of these documents

might be harmful to our company and would give competitors an unfair advantage in the market.

Schematic Diagram

Block Diagram

Operational Description

Parts List

Tune-up Procedure

External Photos

Test Setup Photos

Internal Photos

User Manual

In additional to above mentioned documents, in order to comply with the marketing regulations

in Title 47 CFR §2.803 and the importation rules in Title 47 CFR §2.1204, while ensuring that

business sensitive information remains confidential until the actual marketing of newly

authorized devices, we request Short Term Confidentiality of the following attachment(s);

OR

For 45 days, pursuant to Public Notice DA 04-1705.

For 180 days pursuant to KDB 726920 D01.

It is our understanding that all measurement test reports, FCC ID label format and

correspondence during the certification review process cannot be granted as confidential

documents and this information will be available for public review once the grant of equipment

authorization is issued.

Sincerely,

Signature:

Name: Sanghyo Kim

Title: CTO



 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

XPLORA Technologies AS

WIFI Channel 12 and 13 Declaration Letter

We declare the equipment identified below with regards to Channel 12 and 13 capabilities for

FCC ID: 2AVMJ-XGO2

Declaration

Product hardware does not have the capability to operate on Channel 12 and 13.

Product hardware has the capability to operate on Channel 12 and 13. However,

these two channels will be disabled via software and will not be accessible to user.

Product hardware has the capability to operate on Channel 12 and 13. However, all

the operated channels can’t be changed in the RF parameter via software. All

channels have complied with all of the requirements sets out in FCC Part 15.247.

Product hardware has the capability to operate on WiFi Channel 12 and 13, and

meets the requirements of KDB 594280 D01 v02r01. Please note:

1.) By default, this device operates in a mode that is compliant with the U.S.

requirements.

2.) This device will also use supplemental information such as geo-location data

to determine that it is operating outside the U.S., if necessary, to change its

power. Such supplemental data will be derived from the following:

Global Navigation Satellite System (GNSS)7 sensors in the device

Mobile Country Code (MCC),8 or MCC with a Mobile Network code (MNC), received

from a CMRS9 carrier and received directly by a receiver on the device

Country information derived from multiple adjacent access points (for example using

IEEE Std 802.11d provisions) may be permitted on case-by-case basis

Other suitable geo-location data based on IP addresses or other reliable source.

Name / Title: Sanghyo Kim / CTO

Signature:

Tel: +447479553848

Email: office@myxplora.com

Date: 2021-07-23

Page 1 of 1

Rev.2.0